Page 1
CRAFTSMEN, INC.
Assembly Instructions
Model 1575
Wide Cuisine Cart
GENERAL:
1. You have purchased model 1575. Overall dimensions of an assembled unit is 32” x 17 x 34.5”
2. Should you need assistance or need to replace a damaged or missing part, DO NOT
RETURN THE UNIT TO THE STORE where you purchased it, simply give us a call at
607-652-7321 from 7:30 - 4:00 PM Eastern time and we’ll send you the prepaid part via UPS
usually that same day! Please have model number and part description ready when you call.
3. Read the assembly instructions and the enclosed brochure before beginning assembly.
Assembly is very easy if you read and follow the instructions step by step.
4. Tools required: Phillips screwdrivers, medium and small; medium flat blade screwdriver and
hammer.
Page 2
CABINET PARTS
TOP
P1 P2 P3
Handle Side Panel (1)
T1
TOP
Plain Side Panel (1)
TOP
S
Shelf (2)
Back Panel (1)
D1
Drawer Front (1)
Cabinet Top(1)
Table Top Stick (2)
Drawer Dowel (1)
D6
Door Spacer (1)
D5
T2
D7
D2
Drawer Back (1)
D4
Drawer Side Left (1)
D8 D9
Left Door (1)
B2
D3
Drawer Side Right (1)
Right Door (1)
Drawer Bottom (1)
Top/Bottom Brace (2)
B1
Middle Brace (1)
Page 3
CABINET HARDWARE
1 3/4” Phillips Flat Head Machine Screw (10)
1 1/4” Phillips Flat Head #8 Screw (14)
1” Truss Head Machine Screw (6)
3/16” Flat Washer (4)
5/8” Phillips Flat Head #8 Screw (2)
1 1/2” Long 3/16” DIA. Steel Pin (4)
10-24 Hex Nut (10)
1” Long 3/16” DIA. Steel Pin (8)
3/4” Long 3/16” DIA. Steel Pin (6)
included in
magnet pack
Towel Bar Post (2)
Cam (2)
5/8 Wooden Disk (12)
Cam Posts (2)
5/8” Pan Head Screw (2)
included in
magnet pack
1/2” Phillips Flat Head #4 Screw (1)
Magnet (1)
Magnet Plate (1)
included in
magnet pack
Nickel Handle (3)
Caster Socket (4)
Locking Wheel Caster (2)
Non Locking Wheel Caster (2)
Polished
Nickel Towel
Bar (1)
Page 4
STEP 1
Repeat to other Side Panel
1 1/4” #8 Screw
1” Steel Pin
T2
P2
T2
STEP 2
Towel Bar Post
Towel Bar
P1
Handle can go on either side of cart so
choose which side you want the towel bar
1 1/4” Screw
Washer
P1 P2
P3
Nut
1 3/4” Machine Screw
Page 5
STEP 3
P3
P1 P2
1 1/4” Screw
T1
Page 6
STEP 4
A. Attach the drawer back to the drawer sides with
four 1 1/4” #8 screws. Make sure parts are aligned
as in illustration 4A.
B. Insert drawer bottom into the slots in the drawer
sides, best side to inside of drawer. Slide down
until seated in the slot in the drawer back.
See illustration4B.
C. Screw the cam posts into the two outside holes
on the inside face of the drawer front until seated.
Only 3/8” of this post goes into the wood, leaving
the 4 guide rings/head exposed. See illustration 4C.
D. Insert the posts into holes in the drawer sides
until seated against the front end of the drawer
sides. Insert cams so that slot in the cam fits over
the post and turn with Phillips screwdriver until
seated. Don’t over-torque! See illustration 4D.
E. Attach drawer handle with the two handle
screws ( no illustration ).
D2
D3 D4
ILLUSTRATION 4A
D2
D1
ILLUSTRATION 4C
Below line in wood
Cam Posts (2)
4 used
in this step
1 1/4” Phillips Flat Head #8 Screw (14)
2 used
in this step
1” Truss Head Machine Screw (6)
D4
D3
D5
ILLUSTRATION 4B
D2
D5
D4
D3
Cam (2)
2 used
in this step
D1
ILLUSTRATION 4D
Page 7
STEP 5
STEP 6
D1
1 1/2” Pin
Magnet Plate
1” Machine Screw
D9
D7
Place drawer in position
1/2” #4 Screw
Handel
5/8” #8 Screw
D6
D8
Door assembly
Page 8
STEP 6
STEP 7
B2
B2
B1
3/4” Pin
Install 3/4” pins in brace ends
B1
B2
Nut
1 3/4” Machine Screw
Page 9
STEP 7
B2
Washer
D9 D8
B1
B2
Page 10
STEP 8
Page 11
STEP 9
S
S
Page 12
STEP 10
5/8” Wooden disk
A. Stick magnet to magnet plate on right door.
B. With left door open, close the right door. The magnet should be positioned over the wooden block
on the bottom of the top front brace. Hold the magnet in place with your thumb, and open the right
door. The magnet will be in the correct position on the block.
C. Secure magnet with the two round head screws in the magnet packet. Center screws in the slots in
the magnet . This will allow adjustment later, if needed.
NOTE: No pilot holes in block, as softwood!
5/8” Pan Head Screw (2)
Magnet (1)
2 Used
in this step
Page 13
013108
For continued beauty and long life of
your Catskill Craftsmen cart, we
recommend Catskill Craftsmen’s Butcher
Block Oil.
If you would like to purchase Butcher
Block Oil directly from Catskill
Craftsmen’s factory, we offer a reduced
price. For one eight ounce (8 fl. oz.)
bottle, which is sufficient for two
applications, simply send $5.95 along
with the completed coupon to the
address below.
Catskill Craftsmen, Inc.
CRAFTSMEN, INC.
15 West End Ave.
Stamford, NY 12167-1296
CRAFTSMEN, INC.
BUTCHER BLOCK OIL COUPON
Please send me _____# of bottle(s) of the
Catskill Craftsmen Butcher Block Oil at $5.95.
My Check or Money Order is enclosed for a
total of $______________.
Item Code: 1575
NAME _____________________________________
ADDRESS __________________________________
__________________________________________
CITY ______________________________________
STATE _________________________ ZIP _______
Please make checks payable to: Catskill Craftsmen Inc.
15 West End Ave. Stamford, NY 12167-1296
Loading...