Catskill Craftsmen 1563 User Manual

CRAFTSMEN, INC.

Assembly Instructions

Model 1563

Cooks Workcenter II With Knife Rack

GENERAL:

1. You have purchased model 1563. This cart is made of the finest Northeastern Hardwood and
matching veneer.

2. Should you need assistance or need to replace a damaged or missing part, DO NOT
RETURN THE UNIT TO THE STORE where you purchased it, simply give us a call and we’ll
send you the prepaid part via UPS usually that same day! [phone] 7:00am- 4:00pm
Eastern Time

3. Read the assembly instructions and the enclosed brochure before beginning assembly.
Assembly is very easy if you read and follow the instructions step by step.

4. The only tools needed are a hammer, a small and a medium Phillips head screwdriver and
medium flat blade screwdriver. A power screwdriver will speed assembly, but is not required.
Place a few drops of vegetable oil on the threads of wood screws before screwing into
hardwood parts.

KF

TOP

TOP

TT

Table Top (1)

P/N: TT-1563

LD RD

Left Door (1)

P/N: DOR-1563L

Knife Rack Face (1)

P/N: KR-FACE-1563

KS

Knife Rack Side (2)

P/N: KR-SIDE-1563

Right Door (1)

P/N: DOR-1563R

Edge Banding

BP SP

Hole Not Used

Back Panel (1)

P/N: BP-1563

CB

Cutting Board (1)

P/N: CB-1563

DS

Door Spacer (1)

P/N: DORS-1563

Side Panel (2)

P/N: SP-1563

SL

Drawer Side Left (1)

P/N: DS-1563/L

SR

Drawer Side Right (1)

P/N: DS-1563/R

BS MS

Bottom Shelf (1)

P/N: BS-1563

Bottom Brace (1)

TB

P/N: B-20 1/2-BF-1563

Top Brace (1)

P/N: B-20 1/2-TF-1563

Middle Shelf (1)

P/N: MS-1563

BB

DF

TS

Table Top Stick (2)

P/N: TTS-1563

DD

Drawer Dowel (1)

P/N: DDL-1563

DB

Drawer Back (1)

P/N: DBK-1563

Drawer Front (1)

P/N: DF-1563

DBT

Drawer Bottom (1)

P/N: DB-1563

1 3/4” Phillips Flat Head Bolt (8)

2” Phillips Flat Head #8 Screw (4)

( 4 are brass
for knife rack )

1 1/4” Phillips Flat Head #8 Screw (16)

Nickel Handle (3)

3/16” Flat Washer (2) 10-24 Hex Nut (8)

Truss Head Machine Screw (6)

5/8” Phillips Flat Head #8 Screw (3)

5/8” Phillips Flat Head #6 Screw (8)

Cam Posts (2)

3/4” Long 3/16” DIA. Steel Pin (4)

1” Long 3/16” DIA. Steel Pin (8)

1 1/2” Long 3/16” DIA. Steel Pin (4)

Polished
Nickel Towel
Bar (1)

Cutting

Board

Cabinet

Cutting Board Glide (1 Set)

5/8 Wooden
Disk (8)

Cam (2)

Towel Bar Post (2)

Magnet Pack

Magnet (1)

Magnet Plate (1)

5/8” Pan Head Screw (2)

1/2” Phillips Flat Head #4 Screw (1)

Caster Socket (4)

Non Locking Wheel Caster (2) Locking Wheel Caster (2)

STEP 1

TS

1 1/4” #8 Screw

SP

TS

SP

STEP 2

Hex Nut

Nut Access Hole

STEP 3

The wheel on the glide

goes toward front of cart

Nut

SPSP SP

BP

1 3/4” Machine Bolt