Page 1
Mount
Parts of Names
Mounting View
5 Main Unit
3 Wire
Fasten the screws
securely
2 Speed Sensor
4 Bracket
Lever
Peel off
Front fork
Caution!:
Insure enough wire clearance in the
area marked with
to allow the
handlebar to fully rotate without pulling
the wire.
C
Setup Guide
®
Align the center of the magnet
and the sensor's mark line while rotating the wheel or crank.
The clearance between the
sensor
and the magnet
should be less than 10 mm.
1 Magnet
Spoke
Bracket
Wire
Speed sensor
Bracket band
Sensor spacer
Magnet
Nylon tie
Bracket screw (long)
Sensor screw (short)
Lithium battery
(CR2032)
Bracket rubber pad
mark line
Remove
model OS1.0
U.S. Pat. Nos. 4642606/5904442/Pat. and Design Pat. Pending
Copyright© Aug. 2000 CAT EYE Co., Ltd.
OS1SME-001019 066600061
2
The position of the sensor and the magnet should be as shown:
Top view
less than 10 mm
Side view
Push
Pull
To remove
EE
Page 2
Setup
How to Use
• Names
1 Installing battery
2 Format operation
Format your unit before staring various setting.
Hold down both MODE/SELECT buttons simultaneously, press and release RESTART button.
Select "YES" and press ENTER/START/STOP.
3 Speed scale setting
4 Tire size setting
5 Date setting
6 Time scale setting
7 Clock time setting
• Custom Setup
Select your favorite functions and preferred font
size. (See "Reference guide" page 7.)
•Start/stop of measurement
By a press of START/STOP button, the unit starts measuring; by another press, it stops measuring. While measuring,
the speed scale icon flashes.
START/STOP/ENTER button measures Elapsed Time
(Tm), Trip Distance (Dst) and Average Speed (Av).
Maximum Speed (Mx) and Total Distance (Odo) continue
to be measured regardless of start/stop.
•Changing lower display
EASY -------- 14inch~27inch
CUSTOM --- 10~9999mm
Setup finished
If "YES" is selected
• Tire Size Calibration Chart
8 Custom setup entrance
Select "NO".
Liquid crystal display
START/STOP button
[ENTER button]
MODE button
[SELECT button (FWD/REV)]
MENU button
RESTART button
Contacts
Battery cover
Elapsed Time (Tm)
Clockwise
Trip Distance (Dst)
Average
Speed (Av)
Maximum Speed (Mx)Totall Distance (Odo)
Clock Time
Counterclockwise
TIRE SIZE mm inch
CUSTOM
EASY
12 x1.75 935
14 x 1.50 1020
14 x 1.75 1055 14inch
16 x 1.50 1185
16 x 1.75 1195 16inch
18 x 1.50 1340
18 x 1.75 1350 18inch
20 x 1.75 1515
20 x 1-3/8 1615 20inch
22 x 1-3/8 1770 22inch
22 x 1-1/2 1785
TIRE SIZE mm inch
CUSTOM
EASY
24 x 1 1753
24 x 3/4Tu 1785
24 x 1-1/8 1795
24 x 1-1/4 1905
24 x 1.75 1890 24inch
24 x 2.00 1925
24 x 2.125 1965
26 x 7/8 1920
26 x 1(59) 1913
26 x 1(65) 1952
26 x 1.25 1953
TIRE SIZE mm inch
CUSTOM
EASY
26 x 1-1/8 1970
26 x 1-3/8 2068
26 x 1-1/2 2100 26/650
26 x 1.40 2005
26 x 1.50 2010
26 x 1.75 2023
26 x 1.95 2050
26 x 2.00 2055
26 x 2.10 2068
26 x 2.125 2070
26 x 2.35 2083
TIRE SIZE mm inch
CUSTOM
EASY
26 x 3.00 2170
27 x 1 2145
27 x 1-1/8 2155 27/700
27 x 1-1/4 2161
27 x 1-3/8 2169
650 x 35A 2090
650 x 38A 2125
650 x 38B 2105
700 x 18C 2070
700 x 19C 2080
700 x 20C 2086
TIRE SIZE mm
CUSTOM
700 x 23C 2096
700 x 25C 2105
700 x 28C 2136
700 x 30C 2170
700 x 32C 2155
700CTubu 2130
700 x 35C 2168
700 x 38C 2180
700 x 40C 2200
•Reset operation
Press START/STOP/ENTER button and either of MODE/
SELECT button simultaneously, and the data other than
Total distance (Odo) and Clock Time is reset.
Press simultaneously
How buttons work in the SETUP process:
PRESSING FWD BUTTON:
Moves to the right or increases the figure
PRESSING REV BUTTON:
Moves to the left or decreases the figure
PRESSING BOTH FWD/REV BUTTONS:
Goes back to the previous screen
PRESSING ENTER BUTTON:
Enters the figure and executes the selection
CLOSE
OPEN
Battery (CR2032)
Loading...