http://www.cateye.com/
CYCLOCOMPUTER
DOWNLOAD KIT
Download unit & Download Software [e-Train Data™ Ver.3]
for Windows 98/ME/2000/XP
0365510 (ENG) 3
INTRODUCTION
The CC-TR100 Download Kit contains the software “e-Train DataTM Ver. 3”and the download kit that connects
the CatEye CC-TR100 to your personal computer.
Please read this manual carefully and keep for future reference.
• Windows is a registered trademark of Microsoft Corporation.
• IBM is a registered trademark of International Business Machines Corporation.
• No part of this manual may be reproduced or transmitted without the prior written permission
of CatEye Co., Ltd.
• If you have any questions or concerns about this manual, please contact CatEye at
www.cateye.com.
1
DOWNLOAD KIT
READING THIS MANUAL
For quick reference, refer to the sections below, or begin at the start of the manual.
Basic installation and operation See page 13-19.
This section describes how to connect the CC-TR100 to your PC using the download kit, and how to
download stored data.
Complete description of e-Train software functions See page 20-26.
Go here for descriptions and meanings of buttons, icons and items on the screens of e-Train Data
Ver. 3.
How to change and customize settings See page 47-48.
Go here to change the settings of e-Train DataTM Ver.3.
Quick highlights:
• Changing the settings of CC-TR100 via the PC ............................................................. see page 19.
• Displaying values from ride (average speed, max speed, etc) ....................................... see page 39.
• Viewing accumulated data ............................................................................................ see page 40.
• Analyzing stored data .................................................................................................... see page 46.
• Training while connected to the PC ............................................................................... see page 49.
TM
See the table of contents on the next page for more specific information.
The meaning of icons in this manual:
IMPORTANT! Sections marked with this icon are important notes and supplementary explanations.
Be sure to follow these instructions to avoid misuse of the product.
NOTE Helpful tips are highlighted this way.
About the manuals
• To use CC-TR100 Download Kit, you should be familiar with the operation and terms of Microsoft Windows
operating system. If you are using Windows for the first time, read the Windows documentation first and
familiarize yourself with the operation of Windows.
• In this manual, “CC-TR100 e-Train DataTM Ver. 3” will be referred to as “e-Train Data Ver. 3,” and “CC-
TR100 series heart rate computer” as CC-TR100, and “personal computer” as PC.
• Note that some functions described in this manual can only be used with optional parts; each optional part
will come with its own operating instructions.
• In this manual, the command names marked with [ ] indicate commands from the pull down menus and
other commands on the menu bar.
Registration
Please register your DOWNLOAD KIT to validate the warranty.
Refer to page 54, and make user registration.
2
DOWNLOAD KIT
TABLE OF CONTENTS
Download kit
INTRODUCTION............................................. 1
READING THIS MANUAL ............................... 2
TABLE OF CONTENTS .................................... 3
ABOUT DOWNLOAD KIT ................................ 4
BEFORE YOU BEGIN ......................................5
Contents of download kit ............................ 5
Parts of download unit ................................ 5
Battery installation ...................................... 5
System requirements for e-Train Data Ver.3 ...
6
INSTALLING e-Train Data Ver. 3 .................... 7
UNINSTALLING e-Train Data Ver. 3 ................ 11
CONNECTING DOWNLOAD KIT ..................... 13
Connecting to PC ........................................ 13
Connecting CC-TR100 ................................. 13
SETTING SERIAL PORT ................................. 14
Select the serial port to be used .................. 14
Watching connection and icon on the
task tray ...................................................... 14
To suspend watching connection ................ 15
To resume watching connectio ....................15
DOWNLOADING DATA ...................................16
Changing the CC-TR100 settings via the PC ..19
OPERATING e-Train Data Ver. 3 ..................... 20
Starting e-Train Data Ver. 3 ......................... 20
Operating the “e-Train Data Ver.3 Data View”
screen ......................................................... 23
MANAGING DATA .......................................... 27
Opening data ...............................................27
Deleting data ............................................... 28
Importing data ............................................ 29
Converting data to other file formats ........... 29
MAKING A TRAINING PLAN .......................... 30
Adding a training plan ................................. 30
Loading a plan ............................................. 32
Saving a training plan .................................. 33
PRINTING DATA ............................................ 34
DISPLAYING LAP DATA ................................. 35
DISPLAYING HEART RATE ZONES ................ 36
Heart rate (HR) zone ................................... 36
DISPLAYING CADENCE ZONE ....................... 37
Cadence (CDC) zone ................................... 37
DISPLAYING POWER ZONES ........................ 38
Power zone ................................................. 38
DISPLAYING DATA SUMMARY...................... 39
Displaying data overview ............................. 39
Entering notes ............................................. 39
DISPLAYING DATA HISTORY .........................40
Displaying training history .......................... 40
Displaying graph of time in zone .................43
DATA ANALYSIS ............................................ 46
CHANGING SETTINGS ...................................47
Changing e-Train Data Ver. 3 settings.......... 47
Changing user settings ............................... 48
EXITING e-Train Data Ver. 3 ........................... 48
ON-LINE MEASUREMENT ............................. 49
Online measurement procedure .................. 49
Exploring the “On-Line [e-Train Data Ver. 3]”
screen ......................................................... 50
QUICK REFERENCE ....................................... 52
TROUBLESHOOTING .....................................53
COPYRIGHT................................................... 54
LIMITED WARRANTY ....................................54
REGISTRATION ............................................. 54
REGISTRATION CARD ...................................55
3
DOWNLOAD KIT
ABOUT DOWNLOAD KIT
The Download Kit connects CC-TR100 and your personal computer via the download unit, and downloads
data stored in CC-TR100 using included e-Train Data Ver. 3.
About e-Train Data Ver. 3
e-Train Data Ver. 3 is the software that downloads data stored in CC-TR100.
On the PC screen, e-Train Data Ver. 3 arranges the downloaded data in graph format.
Main features
Downloading CC-TR100 data
Downloads stored data in CC-TR100 to the PC for data log and analysis.
IMPORTANT!
If the power unit is available, download the data according to the connection procedure described in the eTrain Data Instruction Manual of the power unit.
Power related data cannot be downloaded using this download unit.
NOTE
Data of MSC-2Dx and MSC-3Dx can be read using the download unit (IF-MSC1) included in the MSC
Download Kit.
Main screen
The stored data is displayed in graph format: The lower window, or full data window, displays all of the data.
The upper window, data zoom window, displays only the section of data displayed by the graph cursor in the
lower window.
The main screen has the following features:
Multiple Data Display
Superimposes lap data, heart rate target zone data and cadence zone data over recorded data. The user
can display additional training zones for further analysis.
Axis display
You can change the horizontal axis between elapsed time and trip distance with a click of the toolbar. You
can also switch display/non-display of the calibration markings and change the calibration of the horizontal axis.
Analysis
Capable of analyzing each zone data and training data combined.
Data summary
Displays history of stored data in bar graph format, including time in zones.
Schedule
You can enter your training schedule in the calendar. The downloaded data can be displayed in the calendar.
Online measurement
To use this function, the optional Power Unit is required. Power and torque data can be recorded 'live' if
connected to the PC while training indoors.
Changing CC-TR100 settings
The settings of CC-TR100 can be changed on your PC while the CC-TR100 is connected.
Downloaded data
The downloaded data is saved in its original format. Data can be exported and imported from desktop files.
4
DOWNLOAD KIT
BEFORE YOU BEGIN
C
A
B
D
Please be sure to check the following item before using a download kit.
Contents of download kit
Your package includes the following items:
A. CD-ROM -------------------------------------- 1
B. Download unit ------------------------------- 1
C. 'AAA' size Alkaline Battery (LR03) -------- 4
D. Serial-to-USB converter cable ------------- 1
AAA (LR03) dry batteries
Parts of download unit
OFFON
TR100 mount
Contact interface
Power indicator
Battery cover
Power switch
Battery installation
IMPORTANT!
Do not mix new and old batteries. Do not mix different kinds of batteries. Safely dispose of old batteries. Do
not place batteries within reach of children.
1. Install four AAA (LR03) dry batteries.
2. Turn the switch on, and see if the battery indicator lights up.
Battery cover
OFFON
Power switch
If not, re-install the batteries again, making sure the batteries are properly installed.
IMPORTANT!
The download unit continues to consume battery when the switch is on. When not using, turn off the
switch to save the battery life.
NOTE
The battery life is approximately 50 hours (with 1.5 volt alkaline batteries). If the battery indicator does
not turn on, replace the batteries with new ones.
5
DOWNLOAD KIT
System requirements for e-Train Data Ver.3
Personal computer -------------- Windows 98/ME/2000/XP
A USB port or RS232C port (serial port) must be available.
• The connector of the Download Unit is a 9-pin serial connector.
• For connecting to a USB port, use the converter cable included in the kit.
(The converter cable is compatible with Windows 98SE or later. Any USB
port cannot be used with Windows 98 since the cable is not compatible.)
Display --------------------------- 800 X 600 dot or higher resolution
Available hard disk space ------ 10 MB minimum
Available memory space ------- 32 MB or more
Printer ---------------------------- Windows 98/ME/2000/XP compatible
Mouse ---------------------------- Windows 98/ME/2000/XP compatible
6
DOWNLOAD KIT
INSTALLING e-Train Data Ver. 3
IMPORTANT!
Installation using Windows XP is described in the example: follow this procedure even if your OS is not
Windows XP, unless otherwise specified.
e-Train Data Ver. 3 is installed under “Program files” unless you specify another folder.
IMPORTANT!
If you have been using the old version of e-Train Data, uninstall it first.
If installation of the new e-Train Data Ver. 3 is unsuccessful, uninstall it and try again.
1. Turn on your computer.
2. Insert the e-Train Data Ver. 3 CD-ROM in your CD drive.
3. The CD menu appears automatically.
NOTE
If the CD menu does not appear automatically, double-click the “setup.exe” file in the CD drive.
4. Click “Install e-Train Data Ver.3.”
The installer will start automatically.
7
DOWNLOAD KIT
5. Click the [Next] button.
The “Select installation Folder” screen appears.
To change the folder, click the [Browse] button.
Specify the desired folder, and click the [OK] button.
NOTE
If the specified folder does not exist, a new folder is automatically created.
To check the amount of available space on the disk, click the [
Disc Cost...] button.
Click the [OK] button to close the window.
8
DOWNLOAD KIT
6. Click the [Next] button.
The Confirm Installation screen appears.
NOTE
To change the setting, press the [Back] button for return to the previous step, and change the setting.
7. Click the [
Next] button.
Installation begins.
8. After the files being copied, the installation of the driver for the serial-to-USB converter cable starts.
NOTE
For Windows 98, click the [Cancel] button to exit the installation. For Windows 98SE or later, click the
[Next>] button to continue the installation.
9. Click the [Next] button.
Installation begins.
9
DOWNLOAD KIT
10.When all of the files are copied, the “Installation Completed” screen appears.
Clicking the [Finish] button completes the installation of the driver for the serial-to-USB converter
cable.
11.Click the [Close] button to end installation.
10
DOWNLOAD KIT
UNINSTALLING e-Train Data Ver. 3
IMPORTANT!
Uninstallation from Windows XP is described in the example. Follow the procedure even if you are not using
Windows XP, unless otherwise specified.
1. Click the [Start] button.
The Start menu appears.
2. Click the [Control Panel] button.
The Control Panel appears.
IMPORTANT!
In some versions of the Windows, select [Set] - [Control Panel] in the Start Menu.
11
DOWNLOAD KIT
3. Click the [Change or Remove Programs] button.
The “Add or Remove Programs” screen appears.
IMPORTANT!
In some versions of Windows, click [Add or Remove Applications].
4. Select “e-Train Data Ver. 3,” and click the [Remove] button.
IMPORTANT!
In some versions of Windows, click the [Add/Remove] button.
5. Click the [Yes] button in the “Add or Remove Programs” window.
Uninstallation begins.
6. When the e-Train Data Ver.3 has been deleted, uninstallation is complete.
12
DOWNLOAD KIT
9-pin serial cable
CONNECTING DOWNLOAD KIT
Connecting to PC
Connecting to serial port
Connect the cable of the Download Unit to the 9-pin RS232C terminal (serial port) of the PC.
NOTE
• The connector of the cable is a 9-pin serial connector. It is compliant with IBM and IBM compatibles. For
some computer models, a separate converter adapter is required.
To USB port
serial-to-USB
converter cable
Connecting to USB port
Connect the 9-pin RS232C terminal of the serial-to-USB converter cable to the cable of the Download Unit,
and connect it to the USB port of the PC.
IMPORTANT!
• Connect the cables securely. If they are not connected securely, data transfer may not be carried out
successfully.
Connecting CC-TR100
1. Attach the CC-TR100 to the Download Unit securely until a click is heard.
IMPORTANT!
If the contact points of CC-TR100 and the Download Unit are loosely connected, download may not be
carried out successfully. Be sure to insert it securely.
2. Turn on the power switch 2 of the Download Unit, and make sure that the power indicator lights up.
When the power indicator lights up, the Download Unit is now ready to use.
Disconnecting CC-TR100
After download is completed, turn off the power switch, and remove the CC-TR100 from the Download Unit.
CC-TR100
TR100 Mount
DOWNLOAD KIT
Power Indicator
Power Switch
13
SETTING SERIAL PORT
Select the serial port to be used
1. Right-click the [Connection Manager] icon on the task tray.
A pop-up menu appears.
2. Click “Setup” on the pop-up menu.
The Serial Port Setup dialog appears.
NOTE
Alternatively, double-click the icon to display the dialog.
3. Select the using serial port number from “Serial Port”, and click the [OK] button.
When the port number is uncertain:
When the port number is uncertain, click the [Auto Recognition] button.
The Download Unit automatically recognizes the serial port being connected.
IMPORTANT!
Connection Manager exclusively uses the serial port selected in e-Train Data Ver.3 and other programs
cannot use the serial port accordingly.
To use the serial port with other programs when using Connection Manager, refer to “To suspend
watching connection” (page 15).
Watching connection and icon on the task tray
When the icon on the task tray shown as below, Connection Manager is using the serial port to watch
the download connection.
When the icon on the task tray shown as below, Connection Manager releases the serial port to
suspend watching the download connection.
14
DOWNLOAD KIT
To suspend watching connection
1. Right-click the [Connection Manager] icon on the task tray.
A pop-up menu appears.
2. Confirm the check on “Watch Connection on the pop-up menu.”
When checked, Connection Manager is using the serial port to watch the download connection.
When unchecked, Connection Manager releases the serial port to suspend watching the connection.
3. When checked, click “Watch Connection on the pop-up menu.”
The check mark is removed, and Connection Manager temporarily releases the serial port to suspend
watching the connection.
To resume watching connection
1. Right-click the [Connection Manager] icon on the task tray.
A pop-up menu appears.
2. Confirm the check on “Watch Connection”
When checked, Connection Manager is using the serial port to watch the download connection.
When unchecked, Connection Manager releases the serial port to suspend watching the connection.
3. When unchecked, click “Watch Connection.”
The check mark appears, and Connection Manager exclusively uses the serial port to resume watching
the connection.
15
DOWNLOAD KIT
DOWNLOADING DATA
MENU button
S
T
A
R
T
S
T
A
R
LAP
R
E
T
N
/
S
E
/
T
P
O
LAP
R
E
T
T
N
/
S
E
/
T
P
O
MODE-2 button
NOTE
When, after the power unit is connected to the PC, measurement is carried out, download the data according to the connection procedure described in the e-Train Data Instruction Manual of the power unit.
Power related data cannot be downloaded using this download unit.
1. Turn on your computer and make sure the CC-TR100 and download unit are properly connected to the PC.
2. Press the [MENU] button of CC-TR100.
3. Press the [MODE-2] button of CC-TR100 until the “PC Link” screen appears on CC-TR100.
PC Link Icon
4. Press the [START/STOP/ENTER] button of CC-TR100.
When the CCTR-100 is connected to the PC for the first time or after formatting, the user’s registration
screen appears. Enter the user name and click the “OK” button.
LAP
S
T
R
A
E
R
T
T
N
/
S
E
/
T
P
O
START/STOP/ENTER button
5. When the PC acknowledges the connection with CC-TR100, the message “COMPUTER ACKNOWL-
EDGED” appears.
The “PC Online” screen appears on CC-TR100.
IMPORTANT!
When “Power Select” of the CC-TR100 setting is ON, the “Online Power Measurement” appears.
The “PC Online” screen
If the connection to CC-TR100 cannot be established, check the following
• Check the connection between the Download Unit and the PC.
• Check the connection between the Download Unit and CC-TR100.
• Restart the PC, and follow the connecting procedure again.
• Refer to additional troubleshooting on page 53.
If the connection is still not established, reinstall e-Train Data Ver. 3.
16
DOWNLOAD KIT
6. Clicking the [Download] button will open a list of data stored in the CC-TR100.
IMPORTANT!
Press [MODE-1] on the CC-TR100 if “Power Select” is ON, then click the [Download] button on the PC
screen.
Pressing [START/STOP/ENTER] on the CC-TR100 while “Power Select” is ON will start online power
measurement.
7. A list of files stored in the CC-TR100 appears.
8. Select the file that you wish to download.
NOTE
You can delete unnecessary data from CC-TR100. Select a file, and click the [Delete] button.
When “Delete data in CC-TR100 after download” is checkmarked, the data in CC-TR100 is deleted after
the download is completed.
9. Click the [Download] button to begin download process.
IMPORTANT!
• It takes a maximum of 5 minutes to download data. Wait until the download is completed.
• If an error occurs during download, an alert will appear. Restart the PC, and redo the download pro-
cess.
• A probable cause of a download error is a loose connection between the contact points of CC-TR100
and the Download Unit. Check that CC-TR100 is securely attached to the Download Unit.
17
DOWNLOAD KIT
Loading...