CASTLE Euro ONE, EURO ONE PLUS User Manual
User
Manual
For use with end station 28, MSX 44
MSX 76, MSX 280 software:
Version 6.00 or above
RINS1020-6
You’ve Made the Right Choice
Page 1
Contents
Introduction 1-5
Using Euro-MERiDIAN with Code or
Tag
6-10
Intelligent Setting 12-13
When Problems Arise 15-17
Setting Individual Areas 18-21
Chime Facility 22
Omitting Zones 23-24
Keypad Hold Up/Personal Attack 25
Manager Menu 27-28
Omitting 24 hr Zones 30
Changing Date & Time 29
Change/Add Codes or Tags 31-35
Review History Log 36
SMS Phonebook 38
Walk Testing Detectors 39
Testing your Sounder 40
SMS Messaging System 41-42
Dial Out Menu 43
Allow Engineer Menu 44
Block Remote Set 45
Perform Anti-Code Reset 46
Service & Codeholder Records 50-51
SMS Disclaimer 52
Note the specification of Euro-MERiDIAN ONE
and ONE plus panels may vary between
models, and some facilities in the manual may
not be available. Check with your installer for
full details. This equipment may be used in
systems installed to a lower grade, which will
be agreed with your installation company.
There are no user serviceable parts contained
in this product.
© Castle Care-Tech 2008 (RINS1020) Issue 4
You’ve Made the Right Choice
Page 2
Using your Euro-MERiDIAN Alarm System
just couldn’t be easier!
This is the Keypad from where you
control your Alarm System*
Note:
For your security, the keypad becomes
disabled for 90 seconds after 30 incorrect
key-presses, or after 6 attempts to present
invalid tags. It will subsequently be
disabled again after 7 further incorrect
key-presses or after another invalid tag is
presented. Once a correct code or tag has
been registered, the keypad is returned to
normal operation.
*Please note that Keypad design may differ from that shown.
The Euro Keypad
Page 3
The display gives you any
important messages. It will alert
you if you need to call your alarm
installation engineer.
The 10 digit numeric keypad is
where you use your PIN code.
The A B C D keys help simplify use,
and will illuminate to highlight your
choice of security cover, or flash if
there is a problem.
This is where you present your
Tag
.
E
uro 1
Ti
me: 15:02
MAINS FAIL
Warning Indications
Page 4
All setting points (Keypads or Tag
Readers) have lamps to clearly
indicate what is happening.
The ‘Alert’ lamp will flash if there is
information available to you. Enter your
code to see the information. After a code
has been entered, one of the following
lamps will light: Alarm, tamper or fault.
The relevant detail of the problem will be
shown on the display. To clear the display,
press the ‘Yes’ key (or the display will
clear automatically after 3 minutes.)
The ‘Alarm’ lamp will flash after code
entry if an alarm occurs.
The ‘Tamper’ lamp will flash after code
entry if the wiring or equipment is
tampered with.
The ‘Fault’ lamp will light after code entry
to indicate if a technical fault occurs.
The ‘Unset’ lamp will light for 5 seconds if
the panel is completely Unset (steady) or if
some areas remain Set (flashing). It will
also light during the setting procedure,
going off once set.
Alert Alarm Tamper Fault Unset
Using Tags
Page 5
Euro-MERiDIAN’s High Security
Proximity Tag (or Card) will set or
unset your Alarm system with the
minimum of fuss or complexity.
The Tag contains NO batteries and
is completely maintenance free.
Just touch the Tag to the fascia
below the logo to use.
The Keypad will BEEP to
acknowledge the TAG.
Security Checks
Page 6
Before you set your system:
You must ensure all doors and
windows are securely closed and
any pets or people are excluded
from areas protected by movement
sensors.
Close Windows
Close Doors
Exclude Pets & People
Leaving the Building
Page 7
If you are leaving the building, go
to Keypad and key in your PIN
code, or present your Tag.
Exit tone Starts
The appropriate area (ABCD) keys
will illuminate.
(If flexi-set is enabled you will be able to
choose which areas you set, see page 19)
Leave by agreed Exit Route
Close and Lock the Final Exit
Door
Finally, press the ‘Push to Set’
button (if fitted) that is mounted
externally by the final exit door.
Exit tone will cease
Euro-MERiDIAN is now SET
SETTING [009]
OFFICE
If your exit is timed,
you will see the above
screen.
If you use a Push-toSet button, or finaldoor-set, you will see
the screen below.
E
uro 1
Ti
me: 15:02
L
eave via
Exit Route
Faults when you Switch On
Page 8
If when you key in your PIN code
(or present your Tag) a warning
tone sounds and the
fault
lamp
comes on, the keypad display will
show the nature of the problem.
An appropriate
A B C D
key will
flash to indicate within which area
the fault exists.
The tone will cease after about 10
seconds.
Press the NO key
The system will remain unset, so
you can resolve the problem.
For example, you may have left a
door open, if so, close the door.
Now commence the setting
procedure again.
UNABLE TO SET
BACK DOOR
Faults when Leaving the
Building
Page 9
If when you have closed the final
exit door (and pushed the
‘Push
to Set’
button if fitted), the exit
tone continues to sound an
interrupted tone…
“beep – beep – beep – “
You have probably left a
protected door on the exit route
open.
Return to the keypad and note
the message on the display.
Stop the setting procedure with
your PIN code, or Tag.
Close the open door
Now commence the setting
procedure again (see page 7).
EXIT VIA
HALLWAY
Entering the Building
Page 10
To enter the building you
must
use the agreed entry route and
go straight to the keypad.
Entry tone will be sounding
“beep – beep – beep –“
Key in your PIN code, or present
your Tag.
Entry tone will cease
To indicate that the system has
unset, the unset lamp will
illuminate for five seconds.
Euro-MERiDIAN is now UNSET
ENTRY
[010]
TIME
**
ENTRY
[020]
TIME
Using an External Proximity
Reader
Page 11
Setting the Euro One with the Proximity Reader
Action Visual Sequence
Present a valid
tag to the
reader and
then remove it.
The GREEN LED
will come on
Present the
same tag to the
reader, and then
remove it. The
exit time will start
on the control
panel.
The RED LED may
be programmed to
illuminate under
certain actions (for
example when the
system is armed)
Unsetting the Euro One with the Proximity Reader
Action Visual Sequence
Present a valid
tag to the
reader and
then remove it.
The GREEN LED
or RED LED (if
programmed) will
be displayed
Present the
same tag to
the reader,
and then
remove it. The
exit time will
start on the
control panel.
The RED LED will
extinguish, and
after 25 seconds
the GREEN LED
will extinguish.
Part Setting the System
Page 12
Intelligent Set
(if programmed)
If you wish to set Euro-MERiDIAN
and stay in the building (eg set
the alarm at night), the EuroMERiDIAN’s intelligent operating
system will realise which level of
security you require and will set
only part of the system.
You will NOT need to press a
Push-to-Set button if you set
only part of a system.
If intelligent set is not installed on
your system, you may part set
the system as described on Pages
18-19.
Using an External Proximity
Reader
Page 13
Intelligent Set
To Part Set Euro-MERiDIAN go to
the keypad and enter your PIN
code or present your Tag.
The appropriate
A B C D
keys will
illuminate
Exit tone will start
Leave the protected area and
retire to the un-protected area
(eg upstairs).
Euro-MERiDIAN will detect you
have gone upstairs and set the
appropriate areas accordingly.
After a preset time the exit tone
will cease.
Euro-MERiDIAN is now Part
Set
Using an External Proximity
Reader
Page 14
When
Problems
Arise, Just
Key in your
PIN Code or
present your
Silencing Alarms
Page 15
If an Alarm tone sounds, the Alert
lamp will flash:
Just key in your PIN code or
Present your Tag.
The Alarm will stop sounding
The display will indicate the
problem.
Press the
‘YES’
Key
Euro-MERiDIAN will advise you on
any action that is needed. If the
‘Alert’ LED indication remains lit,
there is additional information
available. Enter your PIN or
present your Tag to view.
Call Engi
neer
Low Volts
Al
arm
Sil
ence
d
Low Volts
Engineer Reset
Page 16
When an alarm has been cancelled and
the Police have been notified by the
Alarm Receiving Centre, you will see the
following screen when you try to use the
system.
It is usually necessary for an engineer
from your installation company to check
the installation and reset the system for
further use.
But if you have caused
the alarm in error
your Alarm
Receiving Centre or Alarm Installation
Company may permit you to reset the
system without an engineer present.
You will be required to quote a 6-digit
code by telephone (advise them that the
system is a Castle Euro-MERiDIAN). You
will then be given a special code which
will reset the system
for that one
occasion
only.
Press ‘NO’
Enter the anti-code given to you by your
installation company.
You alarm in now restored and ready to
use.
This 6-digit code is also displayed in the
‘user menu’ – see page 46.
Quote G19867
Anti-Code Needed
E
uro 1
Time:15:15
Engi
neer Restore
Performed
Quote G19867
Anti-Code Needed
Ent
er your Code
[* ]
Automatic Inhibit
Page 17
Euro-MERiDIAN is designed to
automatically disable certain
functionality. The factory default
settings are as shown below:
Intruder
Alarm
Signal
After 3* unconfirmed alarms
in the same area or 1
confirmed alarm.
Tamper
Alarm
Signal
After 3* unconfirmed alarms
in the same area or 1
confirmed alarm.
Keypad
After 30 keypresses without
entering a valid code, keys are
disabled for 90 seconds. After
reinstatement, this will be
repeated after each 7
keypresses until a valid code is
entered.
Tag Reader
(or Tag at a
keypad)
After 6 presentations of an
invalid tag, the reader will be
disabled for 90 seconds. After
reinstatement, this will be
repeated for each invalid tag
until a valid tag is used.
*
This figure is programmable by the installing company
Loading...