Castex LS-1700, LS-1700HD, LS-2000, LS-2000HD, TS-1700HD Operator And Parts Manual

LS-1700/LS-1700HD
LS-2000/LS-2000HD

TS-1700HD/TS-2000HD

Low Speed Floor Machine

Model No.:
607265 – LS-1700
607266 – LS-1700HD
607267 – LS-2000
607268 – LS-2000HD
607263 – TS-1700HD
607264 – TS-2000HD

Operator and Parts Manual

CASTEX INCORPORATED

12875 RANSOM STREET
HOLLAND MI 49424 U.S.A.

A TENNANT COMPANY

1–800-522–7839
616-786–2330
FAX: [phone]
CUSTOMER S E RVICE: 1–800-964–9644

607583

Rev. 00 (04-99)

OPERATION

This manual is furnished with each new model. It
provides necessary operation and maintenance
instructions.

Read this manual completely and understand the
machine before operating or servicing.

This machine will provide excellent service. However,
the best results will be obtained at minimum costs if:

S The machine is operated with reasonable care.
S The machine is maintained regularly – per the

maintenance instructions provided.

S The machine is maintained with manufacturer

supplied or equivalent parts.

TABLE OF CONTENTS

MACHINE DATA

Please fill out at time of installation for future reference.

Model No.­Install. Date ­Serial No.-

Copyright E2000 Tennant Company Printed in U.S.A.

Castex is a registered United States trademark of Tennant Company.

SAFETY PRECAUTIONS 3. . . . . . . . . . . . . . . . . . . . . .

MACHINE COMPONENTS 4. . . . . . . . . . . . . . . . . . . .

MACHINE SETUP 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

MACHINE OPERATION 5. . . . . . . . . . . . . . . . . . . . . . .

MACHINE MAINTENANCE 6. . . . . . . . . . . . . . . . . . . .

STORING MACHINE 6. . . . . . . . . . . . . . . . . . . . . . . . . .

RECOMMENDED STOCK ITEMS 6. . . . . . . . . . . . . .

TROUBLE SHOOTING 7. . . . . . . . . . . . . . . . . . . . . . . .

SPECIFICATIONS 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ELECTRICAL DIAGRAMS 8. . . . . . . . . . . . . . . . . . . .

PARTS LIST 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

OPTIONS 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2

LS-1700/LS-1700HD/TS-1700HD/LS-2000/LS-2000HD/TS-2000HD (03–01)

SAFETY PRECAUTIONS

This machine is intended for commercial use. It is
suited to scrub floors in an indoor environment and is
not constructed for any other use. Use only
recommended pads/brushes and cleaning solutions.

The following safety alert symbols are used throughout
this manual as indicated in their descriptions:

OPERATION

4. Before leaving or servicing machine:

– Turn off machine.
– Unplug cord from wall outlet.

5. When servicing machine:

– Unplug cord from wall outlet.
– Avoid moving parts. Do not wear loose

jackets, shirts, or sleeves.

– Use manufacturer supplied or approved

replacement parts.

WARNING: To warn of hazards or unsafe
practices which could result in severe personal
injury or death.

FOR SAFETY: To identify actions which must be
followed for safe operation of equipment.

The following information signals potentially dangerous
conditions to the operator or equipment:

FOR SAFETY:

1. Do not operate machine:

– Unless trained and authorized.
– Unless operator manual is read and

understood.

– In flammable or explosive areas unless

designed for use in those areas.

– Unless cord is properly grounded.
– With damaged cord or plug.
– If not in proper operating condition.
– In outdoor areas.
– In standing water.

2. Before operating machine:

– Make sure all safety devices are in place

and operate properly.

3. When using machine:

– Do not run machine over cord.
– Do not pull machine by plug or cord.
– Do not pull cord around sharp edges or

corners.

– Do not unplug by pulling on cord.
– Do not stretch cord.
– Do not handle plug with wet hands.
– Keep cord away from heated surfaces.
– Do not release handle grips until pad

comes to a complete stop.

– Go slow on inclines and slippery surfaces.
– Report machine damage or faulty

operation immediately.

WARNING: Hazardous Voltage. Shock or
electrocution can result. unplug machine before
servicing.

GROUNDING INSTRUCTIONS
Machine must be grounded. If it should

malfunction or breakdown, grounding provides a
path of least resistance for electrical current to
reduce the risk of electrical shock. This machine
is equipped with a cord having an
equipment–grounding conductor and grounding
plug. The plug must be plugged into an
appropriate outlet that is properly installed in
accordance with all local codes and ordinances.
Do not remove ground pin; if missing, replace
plug before use.

Grounded
3 Hole Outlet

Ground Pin

(120V)

Grounded Outlet

Grounding

Edge/hole

(230V/240V)

LS-1700/LS-1700HD/TS-1700HD/LS-2000/LS-2000HD/TS-2000HD (01–00)

3

OPERATION

MACHINE COMPONENTS

5

8

7

3

6

12

9

11

MACHINE SETUP

1. Carefully check carton for signs of damage.

1

2

4

10

13

Report damages at once to carrier.

2. Unfold handle to the upright position and lock
handle using the handle lock knob (Figure 1).

FIG. 1

3. Carefully tilt machine back on handle and install
brush/pad driver.

NOTE: Pad driver, pads and brush are sold
separately. Consult your authorized distributor for
pad/brush recommendations.

4. Position brush/pad driver on driver lug and turn
counterclockwise to secure (Figure 2).

1. Handle Grips

2. Control Triggers

3. Safety Lock Button

4. Dual Speed Switch (Dual Speed Model)

5. Circuit Breaker Reset Button

6. Quick Release Power Cord Hook

7. 15 m (50 ft) Power Cord

8. Cord Grip

9. Handle Release Foot Lever

10. Motor Cover

11. Wheels 100 mm (4 in)

12. Handle Lock Knob

13. Brush/Pad Driver

FIG. 2

5. For pad installation, center pad on pad driver and
tap with hand to secure (Figure 3).

4

FIG. 3

LS-1700/LS-1700HD/TS-1700HD/LS-2000/LS-2000HD/TS-2000HD (01–00)

6. Return machine to the upright position.

7. For easy power cord removal, pull and turn cord
hook upward (Figure 4).

OPERATION

EMC MODEL

FIG. 7

FIG. 4

8. Plug power cord into a grounded wall outlet

(Figure 5).

Grounded
3 Hole Outlet

Ground Pin

(120V)

Grounded Outlet

Grounding

Edge/hole

FIG. 5

(230V/240V)

FOR SAFETY: Do not operate machine unless
cord is properly grounded.

9. Lower handle to desired operating height by
stepping down on handle release foot lever, seven
height settings (Figure 6).

MACHINE OPERATION

FOR SAFETY: Do not operate machine unless
operator manual is read and understood.

1. Before operating, lift handle so machine is parallel
to floor (Figure 8).

FIG. 8

2. To begin scrubbing, depress safety lock button
and pull triggers. Release safety lock button once
machine starts (Figure 9).

FIG. 6

10. For Dual Speed machines, position dual speed
switch downward for scrubbing/stripping and
upward for spray buffing (Figure 7).

LS-1700/LS-1700HD/TS-1700HD/LS-2000/LS-2000HD/TS-2000HD (01–00)

FIG. 9

ATTENTION: Use caution when starting out.
Machine will jolt when triggers are pulled.

5

OPERATION

3. To move machine left (A), slightly lower handle. To
move right (B), slightly raise handle. Operate
machine with a side to side motion (Figure 10).

STORING MACHINE

1. Remove brush/pad driver from machine and neatly
coil cord around cord hook and handle.

2. Store in a dry area in the upright position.

3. For minimal storage or transport space, fold
handle down and position as shown
(Figure 11).

A

FIG. 10

4. To stop machine, release triggers and safety lock
button will automatically engage.

FOR SAFETY: When using machine, do not
release handle grips until pad comes to a
complete stop.

NOTE: Circuit breaker may trip under conditions of
excessive overload. Periodically check pad for soil
build–up. To reset circuit breaker switch, wait 15
seconds and push reset button at side of handle.

5. When finished scrubbing perform the following
maintenance procedures:

B

MACHINE MAINTENANCE

WARNING: Hazardous Voltage. Shock or
electrocution can result. Unplug machine before
servicing.

AFTER EACH USE:

FIG. 11

ATTENTION: Do not expose to rain. Store
indoors.

RECOMMENDED STOCK ITEMS

Refer to the Parts List section for recommended stock
items. Stock Items are clearly identified with a bullet
preceding the parts description (Figure 12).

1. Remove pad driver or brush.

2. Wash pads and brush.

3. Clean machine base.

4. Inspect power cord for damage, if worn or

damaged, replace immediately.

5. Wipe power cord with damp cloth and neatly coil

around cord hook and handle. To remove cord,
pull and turn cord hook upward.

6. Periodically check that all bolts and nuts are tight.

7. Every 250 hours of operation check motor carbon

brushes for wear. Replace brushes when 1 cm or
less in length.

6

FIG. 12

LS-1700/LS-1700HD/TS-1700HD/LS-2000/LS-2000HD/TS-2000HD (03–01)