Casio MA1007-EA, 3247 User Manual

MA1007-EA

About This Manual

Indicators

Graphic area A Graphic area B

Operation Guide 3247

Depending on the model of your watch, display text • appears either as dark ﬁgures on a light background or light ﬁgures on a dark background. All sample displays in this manual are shown using dark ﬁgures on a light background. Button operations are indicated using the letters shown • in the illustration. Each section of this manual provides you with the • information you need to perform operations in each mode. Further details and technical information can be found in the “Reference” section.

PM indicator

Snooze alarm indicator

Alarm on indicator

Auto light switch indicator

DST indicator

Mute indicator

Hourly time signal on indicator

General Guide

Press • C to change from mode to mode. In any mode (except when a setting screen is on the display), press B to illuminate

• .

the display

Timekeeping Mode World Time Mode Stopwatch Mode Alarm Mode

Press C.

Timekeeping

Day of week

PM indicator

Hour : Minutes Seconds

To set the time and date

Month – Day

Home time zone

Seconds DST Home Time Zone Hour

Use the Timekeeping Mode to set and view the current time and date

Read This Before You Set the Time and Date !

The times displayed in the Timekeeping Mode and World Time Mode are linked. Because of this, make sure you select a Home Time zone before you set the time and date.

In the Timekeeping Mode, hold down 1. A until the seconds start to ﬂash, which indicates the setting screen. Press 2. C to move the ﬂashing in the sequence shown below to select other settings.

Press 4. A to exit the setting screen.

The day of the week is displayed automatically in accordance with the date (year, • month, and day) settings.

Daylight Saving Time (DST)

Daylight Saving Time (summer time) advances the time setting by one hour from Standard Time. Remember that not all countries or even local areas use Daylight Saving Time.

To toggle the Timekeeping Mode time between DST and Standard Time

DST indicator

To toggle between 12-hour and 24-hour timekeeping

In the Timekeeping Mode, press D to toggle between 12-hour timekeeping and 24-hour timekeeping.

With the 12-hour format, the • P (PM) indicator appears to the left of the hour digits for times in the range of noon to 11:59 p.m. and no indicator appears to the left of the hour digits for times in the range of midnight to 11:59 a.m. With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without • any indicator. The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is • applied in all other modes.

Countdown Timer

Mode

In the Timekeeping Mode, hold down 1. A until the seconds start to ﬂash, which indicates the setting screen. Press 2. C to display the DST setting screen. Press 3. D to toggle between Daylight Saving Time ( displayed) and Standard Time ( displayed).

4. Press A to exit the setting screen.

The DST indicator appears on the display to indicate that • Daylight Saving Time is turned on.

Flash Alert Day Month Year Minutes

When the setting you want to change is ﬂashing, use 3. D and B to change it as described below.

Screen To do this: Do this:

Reset the seconds to

Toggle between Daylight Saving Time ( ) and Standard Time ( )

Specify your Home Time zone

Change the hour or minutes

Change the year

Change the month or day

For details about time zones, see the “City Code Table”. • See “Daylight Saving Time (DST)” for details about DST setting. • For information about Flash Alert, see “Flash Alert”. •

Press D.

Use D (eastward) and B (westward).

Use D (+) and B (–).

World Time

City code

Current time and date in the zone of the selected city code

World Time shows the current time in 48 cities (29 time zones) around the world.

All of the operations in this section are performed in the • World Time Mode, which you enter by pressing C.

To view the time for another city code

In the World Time Mode, press D to scroll eastwardly through city codes.

For full information about city codes, see the “City Code • Table”. If the current time for a city is wrong, check your • Timekeeping Mode time and time zone settings and make necessary changes.

Operation Guide 3247

To toggle a city code time between Standard Time and Daylight Saving Time

DST indicator

In the World Time Mode, use 1. D to display the city code (time zone) whose Standard Time/Daylight Saving Time setting you want to change. Hold down 2. A for about one second to toggle Daylight Saving Time (DST indicator displayed) and Standard

Time (DST indicator not displayed). The DST indicator is on the display whenever you display • a city code for which Daylight Saving Time is turned on. Note that the DST/Standard Time setting affects only • the currently displayed city code. Other city codes are not affected.

Stopwatch

1/100 second

Hours

Minutes

To measure times with the stopwatch

Elapsed Time

D D

Start Stop Re-start Stop Clear

Split Time

D A

Start Split

Two Finishes

D A

Start Split

The time on the screen may not appear to stop immediately when you press a • button to stop timing or to perform a split operation. Despite this, the time recorded by your button operation is accurate.

About Auto-Start

With Auto-Start, the watch performs a 5-second countdown, and stopwatch operation starts automatically when the countdown reaches zero. During the ﬁnal three seconds of the countdown, a beeper sounds with each second.

To use Auto-Start

The stopwatch lets you measure elapsed time, split times, and two ﬁnishes. It also includes Auto-Start.

The display range of the stopwatch is 23 hours, • 59 minutes, 59.99 seconds. The stopwatch continues to run, restarting from zero • after it reaches its limit, until you stop it. The stopwatch measurement operation continues even if • you exit the Stopwatch Mode.

Seconds

Exiting the Stopwatch Mode while a split time is frozen • on the display clears the split time and returns to elapsed time measurement. All of the operations in this section are performed in the • Stopwatch Mode, which you enter by pressing C.

D D

A D

( displayed)

First runner ﬁnishes. Display time of ﬁrst runner.

Split release Stop Clear

Stop

Second runner ﬁnishes.

While the stopwatch screen is showing all zeros in the 1.

Stopwatch Mode, press A.

This displays a 5-second countdown screen. • To return to the all zeros screen, press • A again.

Press 2. D to start the countdown. When the countdown reaches zero, a tone sounds and a • stopwatch timing operation starts automatically. Pressing • D while the Auto-Start countdown is in progress starts the stopwatch immediately.

Split release

Display time of second runner.

Clear

Countdown Timer

The countdown timer can be set within a range of one minute to 24 hours. An alarm sounds when the countdown reaches zero. The countdown timer also has an auto-repeat feature and a progress beeper that signals the progress of the countdown.

All of the operations in this section are performed • in the Countdown Timer Mode, which you enter by pressing C.

Seconds

Hours

Minutes

Auto-repeat

When auto-repeat is turned on, the countdown restarts automatically from the countdown start time when it reaches zero. When auto-repeat is turned off, the countdown stops when it reaches zero and the display shows the original countdown start time.

Pressing • D while an auto-repeat countdown is in progress pauses the current countdown. You can resume the auto-repeat countdown by pressing D, or you can press A to reset to the countdown time starting value.

Countdown Timer Beeper Operations

The watch beeps at various times during a countdown so you can keep informed about the countdown status without looking at the display. The following describes the types of beeper operations the watch performs during a countdown.

Countdown End Beeper

The countdown end beeper lets you know when the countdown reaches zero.

When the progress beeper is turned off, the countdown end beeper sounds for • about 10 seconds, or until you press any button to stop it. When the progress beeper is turned on, the countdown end beeper sounds for • about one second.

Conﬁguring the Countdown Timer

The following are the settings you should conﬁgure before actually using the countdown timer.

Countdown start time; Auto-repeat on/off; Progress beeper on/off

See “To conﬁgure the countdown timer” for information • about setting up the timer.

Progress Beeper

When the progress beeper is turned on, the watch uses beeps to signal countdown progress as described below.

Starting from ﬁve minutes before the end of the countdown, the watch emits four • short beeps at the top of each countdown minute. 30 seconds before the end of the countdown, the watch emits four short beeps. • The watch emits a short beep for each of the last 10 seconds of the countdown. • If the countdown start time is six minutes or greater, the watch emits a short beep • for each second of the ﬁnal 10 seconds before the ﬁve-minute point is reached. Four short beeps are emitted to signal when the ﬁve-minute point is reached.

To conﬁgure the countdown timer

When the setting you want to change is ﬂashing, use 3. B and D to change it as described below.

Setting Screen Button Operation

Hours, Minutes

Auto-repeat

Progress Beeper

To specify a countdown start time of 24 hours, set • .

Press 4. A to exit the setting screen.

• You can also perform steps 1 and 2 of the above procedure whenever you need to view the current auto-repeat and progress beeper settings.

To use the countdown timer

While the countdown start time is on the display in the 1. Countdown Timer Mode, hold down A until the current countdown start time starts to ﬂash, which indicates the setting screen.

If the countdown start time is not displayed, use the • procedure under “To use the countdown timer” to display it.

Press 2. C to move the ﬂashing in the sequence shown below to select other settings.

Hours Minutes

Progress Beeper Auto-repeat

Use D (+) and B (–) to change the setting.

Press D to toggle auto-repeat on ( displayed) and off ( displayed).

Press D to toggle the progress beeper on ( ) and off ( ).

Press D while in the Countdown Timer Mode to start the countdown timer.

The countdown timer operation continues even if you exit • the Countdown Timer Mode. Press • D while a countdown operation is in progress to pause it. Press D again to resume the countdown. To stop a countdown operation completely, ﬁrst pause • it (by pressing D), and then press A. This returns the countdown time to its starting value.

Alarms

Alarm number

Alarm time (Hour : Minutes)

Alarm date (Month – Day)

Alarm Types

The alarm type is determined by the settings you make, as described below.

Daily alarm •

Set the hour and minutes for the alarm time. This type of setting causes the alarm to sound everyday at the time you set.

Date alarm •

Set the month, day, hour and minutes for the alarm time. This type of setting causes the alarm to sound at the speciﬁc time, on the speciﬁc date you set.

1-Month alarm •

Set the month, hour and minutes for the alarm time. This type of setting causes the alarm to sound everyday at the time you set, only during the month you set.

Monthly alarm •

Set the day, hour and minutes for the alarm time. This type of setting causes the alarm to sound every month at the time you set, on the day you set.

To set an alarm time

To set a one-time alarm, display an alarm screen • or . To set the snooze alarm, display the The snooze alarm repeats every ﬁve minutes. •

After you select an alarm, hold down 2. A until the hour setting of the alarm time starts to ﬂash, which indicates the setting screen.

• This operation turns on the alarm automatically.

You can set up to three independent multi-function alarms with hour, minutes, month, and day. When an alarm is turned on, the alarm tone sounds when the alarm time is reached. One of the alarms is a snooze alarm, while the other two are one-time alarms. You can also turn on an Hourly Time Signal that causes the watch to beep twice every hour on the hour.

There are three alarm screens numbered •

for the one-time alarm, a snooze alarm screen indicated by indicated by . All of the operations in this section are performed in the • Alarm Mode, which you enter by pressing C.

In the Alarm Mode, use 1. D to scroll through the alarm screens until the one whose time you want to set is displayed.

. The Hourly Time Signal screen is

Press D.

screen.

and

+ 2 hidden pages