Casio EX-ZS160 Owner's Manual

Digital Camera

User’s Guide

Thank you for purchasing this CASIO product.

• Before using it, be sure to read the precautions contained in this User’s Guide.

• Keep the User’s Guide in a safe place for future reference.

• For the most up-to-date information about this product, visit the official EXILIM Website at http://www.exilim.com/

Accessories

As you unpack your camera, check to make sure that all accessories shown below are included. If anything is missing, contact your original retailer.

Rechargeable lithium ion

battery (NP-80)

* The shape of the power

cord plug varies according to country or geographic area.

Power cord Strap

USB-AC adaptor

(AD-C53U)

To attach the strap to the camera

USB cable

Attach strap here.

Read this first!

• The contents of this manual are subject to change without notice.

• The contents of this manual have been checked at each step of the production process. Feel free to contact us if you notice anything that is questionable, erroneous, etc.

• Any copying of the contents of this User’s Guide, either in part or its entirety, is forbidden. Except for your own personal use, any other use of the contents of this manual without the permission of CASIO COMPUTER CO., LTD. is forbidden under copyright laws.

• CASIO COMPUTER CO., LTD. shall not be held liable for any damages or lost profits suffered by you or any third party due to the use or malfunction of this product.

• CASIO COMPUTER CO., LTD. shall not be held liable for any damages or lost profits caused by loss of memory contents due to malfunction, repair, or any other reason.

• Note that the example screens and product illustrations shown in this User’s Guide may differ somewhat from the screens and configuration of the actual camera.

LCD Panel

The liquid crystal panel of the monitor screen uses high-precision technology that provides a pixel yield in excess of 99.99%. This means that some very small number of pixels may not light or may remain lit at all times. This is due to the characteristics of the liquid crystal panel, and does not indicate malfunction.

Take a few test shots

Before shooting your final image, shoot a test shot to ensure that the camera is recording correctly.

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Read this first! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

General Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Monitor Screen Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

❚

Configuring Monitor Screen Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

❚❙

Quick Start Basics 12

What you can do with your CASIO camera . . . . . . . . . . . . . . . . . . . . . . . . . . 12

First, charge the battery prior to use.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

❚

To load the battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

❚

Charge the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Configuring Basic Settings the First Time You Turn On the Camera. . . . . . . 19

Preparing a Memory Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

❚

To load a memory card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

❚

To format (initialize) a new memory card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Turning the Camera On and Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

❚

To turn power on. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

❚

To turn off the camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Holding the Camera Correctly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

To shoot a snapshot. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

❚

Selecting an Auto Recording Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

❚

To shoot a snapshot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Viewing Snapshots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Deleting Snapshots and Movies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

❚

To delete a single file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

❚

To delete specific files. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

❚

To delete all files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Snapshot Shooting Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

❚

Auto Focus Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

❚❙

Snapshot Tutorial 32

Using the Control Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Changing the Image Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Size) . . 33

Using Flash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(Flash) . . 37

Using the Self-timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Self-timer) . . 39

Using Face Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . (Face Detection) . . 40

Shooting without Disturbing Others . . . . . . . . . . . . . . . . . . .(Silent Mode) . . 41

Using the easy Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (easy Mode) . . 41

Shooting with Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

❚

Optical Zoom and Digital Zoom Switch Point . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

❚❙

Recording Movie Images and Audio 46

To record a movie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Recording Audio Only . . . . . . . . . . . . . . . . . . . . . . . . . . (Voice Recording) . . 48

❚

To play back an audio recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Contents

❚❙

Using BEST SHOT 50

What is BEST SHOT? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

❚

Some Sample Scenes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

To shoot an image with BEST SHOT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Recording a Self-portrait . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

❚❙

Advanced Settings 54

Using On-screen Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

REC Mode Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (REC) . . 56

❚

Selecting a Focus Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(Focus) . . . 56

❚

Changing the Focus Frame Shape . . . . . . . . . . . . . . . . . . . (Focus Frame). . . 58

❚

Using Continuous Shutter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (CS). . . 59

❚

Reducing the Effects of Camera and Subject Movement . . . . (Anti Shake). . . 59

❚

Specifying the Auto Focus Area . . . . . . . . . . . . . . . . . . . . . . . . . . (AF Area). . . 60

❚

Assigning Functions to the [4] and [6] Keys . . . . . . . . . . . . . . . (L/R Key). . . 61

❚

Displaying the On-screen Grid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Grid). . . 61

❚

Using Icon Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Icon Help). . . 61

❚

Configuring Power On Default Settings . . . . . . . . . . . . . . . . . . . . (Memory) . . . 62

Image Quality Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Quality) . . 63

❚

Specifying Snapshot Image Quality . . . . . . . . . . . .(T Quality (Snapshot)). . . 63

❚

Correcting Image Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . (EV Shift). . . 63

❚

Controlling White Balance . . . . . . . . . . . . . . . . . . . . . . . . . (White Balance). . . 64

❚

Specifying ISO Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(ISO). . . 65

❚

Optimizing Image Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Lighting). . . 65

❚

Using Built-in Color Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Color Filter). . . 65

❚❙

Viewing Snapshots and Movies 66

Viewing Snapshots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Viewing a Movie. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Zooming an On-screen Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Displaying the Image Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Viewing Snapshots and Movies on a TV Screen. . . . . . . . . . . . . . . . . . . . . . 68

❚❙

Other Playback Functions (PLAY) 70

Using the PLAY Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Playing a Slideshow on the Camera . . . . . . . . . . . . . . . . . . . . (Slideshow) . . 72

Performing Playback without Disturbing Others . . . . . . . . . .(Silent Mode) . . 73

Rotating an Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Rotation) . . 73

Selecting Images for Printing . . . . . . . . . . . . . . . . . . . . . (DPOF Printing) . . 74

Protecting a File Against Deletion . . . . . . . . . . . . . . . . . . . . . . . . (Protect) . . 74

Resizing a Snapshot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(Resize) . . 75

Cropping a Snapshot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Trimming) . . 75

Adding Audio to a Snapshot . . . . . . . . . . . . . . . . . . . . . . . . . . . (Dubbing) . . 76

❚

To play snapshot audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Copying Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Copy) . . 77

Contents

❚❙

Printing 78

Printing Snapshots. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Connecting Directly to a PictBridge Compatible Printer . . . . . . . . . . . . . . . . 79

Using DPOF to Specify Images to be Printed and

the Number of Copies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

❚❙

Using the Camera with a Computer 84

Things you can do using a computer... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Using the Camera with a Windows Computer . . . . . . . . . . . . . . . . . . . . . . . . 85

❚

Viewing and Storing Images on a Computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

❚

Playing Movies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Using the Camera with a Macintosh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

❚

Connecting the Camera to Your Computer and Saving Files . . . . . . . . . . . . . . . 90

❚

Playing a Movie. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

Using an Eye-Fi Wireless SD Memory Card to

Transfer Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Eye-Fi) . . 93

Files and Folders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

Memory Card Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

❚❙

Other Settings (Set Up) 98

Turning off Eye-Fi Card Communication . . . . . . . . . . . . . . . . . . . . (Eye-Fi) . . 98

Configuring Camera Sound Settings . . . . . . . . . . . . . . . . . . . . . (Sounds) . . 98

Configuring a Startup Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Startup) . . 99

Specifying the File Name Serial Number Generation Rule . . . . . (File No.) . . 99

Configuring World Time Settings . . . . . . . . . . . . . . . . . . . . . (World Time) . 100

Time Stamping Snapshots . . . . . . . . . . . . . . . . . . . . . . . . . . (Timestamp) . 101

Setting the Camera’s Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Adjust) . 101

Specifying the Date Style . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Date Style) . 102

Specifying the Display Language . . . . . . . . . . . . . . . . . . . . . . (Language) . 102

Configuring Sleep State Settings . . . . . . . . . . . . . . . . . . . . . . . . . (Sleep) . 103

Configuring Auto Power Settings . . . . . . . . . . . . . . . . . . (Auto Power Off) . 103

Configuring [r] and [p] Settings . . . . . . . . . . . . . . . . . . . (REC/PLAY) . 104

Disabling File Deletion . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Ü Disabled) . 104

Configuring USB Protocol Settings . . . . . . . . . . . . . . . . . . . . . . . . . (USB) . 105

Selecting the Screen Aspect Ratio and

Video Output System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Video Out) . 105

Formatting Built-in Memory or a Memory Card . . . . . . . . . . . . . . (Format) . 106

Resetting the Camera to Factory Defaults . . . . . . . . . . . . . . . . . . (Reset) . 106

Contents

❚❙

Appendix 107

Precautions during Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

Power Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114

❚

Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114

❚

Battery Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114

❚

Using the Camera in another Country . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115

Using a Memory Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115

Reset Initial Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117

When things don’t go right... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119

❚

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119

❚

Display Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124

Number of Snapshots/Movie Recording Time/Voice Recording Time . . . . . 126

Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128

Contents

General Guide

The numbers in parentheses indicate the pages where each item is explained.

BackFront

42135

bk9 bl bm bn8

[ ]

[

SET

[ ]

]

Zoom controller

(pages 26, 43, 67, 67) Shutter button (page 25)

Flash (page 37)

[ON/OFF] (Power)

(page 23) Front lamp (page 39)

Lens

Microphone

(pages 47, 76)

Bottom

bqbr bp bobs

[r] (REC) button

(pages 23, 25) Back lamp

(pages 15, 17, 37) [0] (Movie) button

(page 46) Strap hole (page 2)

[USB/AV] port

(pages 15, 16, 68, 79, 87, 91) Connector cover

Battery/memory card slots (pages 13, 21)

Tripod hole

Use this hole when attaching to a tripod. Speaker

[SET] button (page 32)

[ ] (Delete) button

(page 29) [p] (PLAY) button

(pages 23, 28) Control button

([8][2][4][6]) (pages 11, 29, 32, 37,

54) Monitor screen

(pages 9, 11)

btckcl

Monitor Screen Contents

The monitor screen uses various indicators, icons, and values to keep you informed of the camera’s status.

• The sample screens in this section are intended to show you the locations of all the indicators and figures that can appear on the monitor screen in various modes. They do not represent screens that actually appear on the camera.

. Snapshot Recording

bk bl bm bn bo

cn cm cl

341657

Remaining snapshot memory

capacity (page 126) Remaining movie memory

capacity (page 46) Recording mode (page 25)

White balance setting

(page 64) Continuous shutter (page 59)

. Shutter Button Half-pressed

3 4 5

Image deterioration indicator (page 44) Metering mode (page 128)

Snapshot image size (page 33)

Snapshot image quality (page 63)

Movie image quality (page 36)

Flash (page 37)

Self-timer (page 39)

Face Detection (page 40)

ISO sensitivity (page 65)

Date/time (page 101)

Exposure compensation (page 63)

Focus frame (pages 26, 60)

Timestamp indicator (page 101)

Battery level indicator (page 18)

Eye-Fi (page 93)

Lighting (page 65)

Anti Shake (page 59)

Focus Mode (page 56)

Recording mode (page 25)

Flash (page 37)

ISO sensitivity (page 65)

Aperture value

Shutter speed

Focus frame (pages 26, 60)

NOTE

• The aperture, shutter speed, and ISO sensitivity values will turn orange when you half-press the shutter button if Auto Exposure is not correct.

. easy Mode

bm bl bk 9 8

. Movie Recording

7 6

. Snapshot Viewing

bl bk

Remaining snapshot memory capacity

3 4 5

3 4

5 6

7 8 9

(page 126) Snapshot image size (page 33)

Flash (page 37)

Self-timer (page 39)

Date/time (page 101)

Timestamp indicator (page 101)

Battery level indicator (page 18)

Eye-Fi (page 93)

Lighting (page 65)

Focus frame (pages 26, 60)

Remaining movie memory capacity (page 46)

Movie image quality (page 36)

Recording mode (page 46)

White balance setting (page 64)

Remaining movie memory capacity (page 46)

Movie recording time (page 46)

Flash (page 37)

Exposure compensation (page 63)

Battery level indicator (page 18)

Movie recording in progress (page 46)

File type

Protect indicator (page 74)

Folder name/file name (page 95)

Snapshot image quality (page 63)

Snapshot image size (page 33)

ISO sensitivity (page 65)

Aperture value

Shutter speed

Date/time (page 101)

Battery level indicator (page 18)

Eye-Fi (page 93)

. Movie Playback

File type

4 5

Protect indicator (page 74)

Folder name/file name (page 95)

Movie recording time (page 46)

Movie image quality (page 36)

Date/time (page 101)

Battery level indicator (page 18)

Eye-Fi (page 93)

8 7

1 2

Configuring Monitor Screen Settings

You can turn display information on and off by pressing [8] (DISP). You can configure separate settings for the REC mode and PLAY mode.

Information display on

Information display + Date/Time on

Information display off No information displayed

Displays information about image settings, etc. (REC mode only).

In addition to information about snapshot settings, displays movie setting information and the date/time screen.

• You can specify the date style you want to use (page 102).

Quick Start Basics

What you can do with your CASIO camera

Your CASIO camera is packed with a powerful selection of features and functions to make recording of digital images easier, including the following three main functions.

Premium Auto

Select Premium Auto recording and the camera automatically determines whether you are shooting a subject or scenery, and other conditions. Premium Auto delivers higher image quality than standard Auto.

See page

25 for more information.

Silent

The Silent mode disables flash, mutes camera operation tones, and changes other settings to help ensure that shooting does not bother others around you.

See page

41 for more information.

BEST SHOT

Simply select the sample scene you want and the camera sets up automatically. Then all you need to do is press the shutter button for perfect images.

See page

50 for more information.

Quick Start Basics

First, charge the battery prior to use.

Note that the battery of a newly purchased camera is not charged. Perform the steps below to load the battery into the camera and charge it.

• Your camera requires a special CASIO rechargeable lithium ion battery (NP-80) for power. Never try to use any other type of battery.

To load the battery

1. Open the battery cover.

Slide the battery cover slider towards OPEN and then open it as indicated by the arrows in the illustration.

2. Load the battery.

With the EXILIM logo on the battery facing downwards (towards the lens side of the camera), hold the stopper next to the battery in the direction indicated by the arrow as you slide the battery into the camera. Press the battery in until the stopper secures it in place.

3. Close the battery cover.

Close the battery cover and then shift the slider towards LOCK.

Battery

Stopper

EXILIM logo

Quick Start Basics

To replace the battery

1. Open the battery cover and remove

Stopper

the current battery.

With the monitor screen side of the camera facing upwards, slide the stopper in the direction indicated by the arrow in the illustration. After the battery pops out, pull it the rest of the way out of the camera.

2. Load a new battery.

Charge the Battery

You can use either of the two following methods to charge the camera’s battery.

• USB-AC adaptor

• USB connection to a computer

. To charge with the USB-AC adaptor

1. Turn off the camera.

Check to make sure that the camera’s monitor screen is blank. If it isn’t, press [ON/OFF] (Power) to turn off the camera.

[ON/OFF] (Power)

2. After connecting the

supplied USB cable to the USB-AC adaptor, plug the power cord into a household power outlet.

USB cable (included with camera)

Large connector

USB

USB port

USB-AC adaptor

Power cord

Quick Start Basics

3. Connect the USB

cable to the camera.

The back lamp should light red, indicating that charging has started. The back lamp will go out when charging is complete. It takes about 130 minutes to achieve a full charge. Charging may take longer depending on charging conditions.

USB-AC adaptor

[USB/AV] port

Small connector

Making sure that the mark on the USB cable connector is towards the lens side, connect the cable to the camera.

USB cable (included with camera)

Back Lamp Operation

Lamp Status Description

Lit Red Charging

Flashing Red

Off Charging complete

Abnormal ambient temperature, USB-AC adaptor problem, or battery problem (page 114)

Back lamp

4. After charging is complete, disconnect the USB cable from the camera

and then unplug the power cord from the power outlet.

Quick Start Basics

. To charge using a USB connection to a computer

The battery loaded in the camera is charged whenever the camera is connected directly to a computer with the USB cable.

• Depending on the setup of your computer, you may not be able to charge the camera’s battery over a USB connection. If this happens, use of the USB-AC adaptor that comes with the camera is recommended.

1. Turn off the camera.

Check to make sure that the camera’s monitor screen is blank. If it isn’t, press [ON/OFF] (Power) to turn off the camera.

[ON/OFF] (Power)

Monitor screen

2. With your computer

turned on, connect the

USB port

USB cable

(included with camera)

camera to it.

Making sure that the mark on the USB cable connector is towards the lens side, connect the cable to the camera.

Large connector

[USB/AV] port

Small connector

IMPORTANT!

• The first time you connect the camera to your computer with the USB cable, an error message may appear on your computer. If this happens, disconnect and then reconnect the USB cable.

Quick Start Basics

Back Lamp Operation

Lamp Status Description

Lit Red, (Lit/Flashing Amber)

Flashing Red

Off, (Lit Green) Charging complete

• The information in parentheses in the above table shows the lamp status while the camera is turned on during charging.

Charging

Abnormal ambient temperature, charging taking abnormally long, or battery problem (page 114)

Back lamp

3. After charging is complete, disconnect the USB cable from the camera

and then from the computer.

IMPORTANT!

• Charging is not performed while the connected computer is in the hibernate mode.

• A charging error can occur immediately after charging begins or some time after charging begins. A charging error is indicated by the back lamp flashing red.

Other Charging Precautions

• With the two charging methods described above, you can charge the camera’s battery (NP-80) without removing it from the camera. You also can charge the battery using an optionally available charger unit (BC-80L). Never use any other type of charger device. Attempting to use a different charger can result in unexpected accident.

• USB charging devices and power supply devices are subject to fixed standards. Use of an inferior device or a device that is not up to standard can cause malfunction and/or failure of your camera.

• Operation is not guaranteed in the case of a computer built or modified by you. Even in the case of a commercially available computer, certain USB port specifications may make it impossible to charge via the USB cable.

• A battery that is still warm due to normal use may not charge fully. Give the battery time to cool before charging it.

• A battery discharges slightly even when it is not loaded in the camera. Because of this, it is recommended that you charge the battery immediately before you need to use it.

• Charging the camera’s battery may cause interference with TV and radio reception. If this happens, plug the charger into an outlet that is further away from the TV or radio.

• Actual charging time depends on current battery capacity and charging conditions.

• Do not use the USB-AC adaptor with any other device.

Quick Start Basics

Checking Remaining Battery Power

As battery power is consumed, a battery indicator on the monitor screen indicates remaining power as shown below.

Remaining Power High Low

Battery Indicator ***

Indicator Color Cyan * Amber * Red * Red

indicates battery power is low. Charge the battery as soon as possible.

Recording is not possible when is indicated. Charge the battery immediately.

• The level shown by the battery indicator may change when you switch between the REC mode and PLAY mode.

• Leaving the camera for about 30 days with no power supplied while the battery is dead will cause its date and time settings to be cleared. A message telling you to configure time and date settings will appear the next time you turn on the camera after restoring power. When this happens, configure date and time settings (page

101).

• See page 130 for information about battery life and number of shots.

Battery Power Conservation Tips

• When you do not need to use the flash, select ? (Flash Off) for the flash setting (page 37).

• Enable the Auto Power Off and the Sleep features to protect against wasting battery power when you forget to turn off the camera (pages 103, 103).

Quick Start Basics

Configuring Basic Settings the First Time You Turn On the Camera

The first time you load a battery into the camera, a screen appears for configuring the display language, date, and time settings. Failure to set the date and time correctly will cause the wrong date and time data to be recorded with images.

IMPORTANT!

• A screen for language selection will not appear in step 2 of the procedure below if you purchased a camera intended for the Japanese market. To change the display language from Japanese in this case, use the procedure under “Specifying the Display Language (Language)” (page 102). Note that a version of this manual in the language you select may not be included with a camera intended for the Japanese market.

• Camera models sold in certain geographic areas may not support display language selection.

1. Hold down [ON/OFF] (Power) until the

back lamp lights green momentarily.

• This indicates that power is on.

[ON/OFF] (Power)

Back lamp

2. Use [8], [2], [4], and [6] to select

the language you want and then press [SET].

[0] (Movie)

3. Use [8] and [2] to select a date style and then press [SET].

Example: July, 10, 2012 YY/MM/DD DD/MM/YY MM/DD/YY

* 12/7/10 * 10/7/12 * 7/10/12

4. Set the date and the time.

Use [4] and [6] to select the setting you want to change and then use [8] and [2] to change it. To switch between 12-hour and 24-hour format, press [0] (Movie).

5. After setting the date and time, use [4] and [6]

to select “Apply” and then press [SET].

6. Use [8] and [2] to select “Auto” or “Premium Auto” as the auto

recording mode and then press [SET].

See page 25 for information about the auto recording modes.

SET

Quick Start Basics

If you make a mistake configuring display language, date, or time settings with the above procedure, refer to the following pages for information about how to correct the settings.

– Display language: Page 102 – Date and time: Page 101

NOTE

• Each country controls its local time offset and the use of summer time, and so they are subject to change.

• Removing the battery from the camera too soon after configuring time and date settings for the first time can cause the settings to be reset to their factory defaults. Do not remove the battery for at least 24 hours after configuring settings.

Preparing a Memory Card

Though the camera has built-in memory that can be used to store images and movies, you probably will want to purchase a commercially available memory card for greater capacity. The camera does not come with a memory card. Images recorded while a memory card is loaded are saved to the memory card. When no memory card is loaded, images are saved to built-in memory.

• For information about memory card capacities, see page 126.

. Supported Memory Cards

– SD Memory Card – SDHC Memory Card – SDXC Memory Card

• The above are supported memory card types as of December 2012.

• This camera supports use of SD memory cards of the following types and capacities: SD memory cards up to 2GB, SDHC memory cards from 2GB up to 32GB, SDXC memory cards from 32GB up to 2TB. Note that the ability to use any particular card with this camera, even if it satisfies the above capacity and type requirements, is not guaranteed.

• This camera supports use of Eye-Fi cards.

Quick Start Basics

To load a memory card

1. Press [ON/OFF] (Power) to turn off

the camera and then open the

battery cover.

Slide the battery cover slider towards OPEN and then open it as indicated by the arrows in the illustration.

2. Load a memory card.

Positioning the memory card so its front is facing upwards (towards the monitor screen side of the camera), slide it into the card slot all the way in until you hear it click securely into place.

Front Back

3. Close the battery cover.

Close the battery cover and then shift the slider towards LOCK.

IMPORTANT!

• Never insert anything besides a supported memory card (page 20) into the memory card slot.

• Should water or any foreign object ever get into the card slot, immediately turn off the camera, remove the battery, and contact your retailer or nearest CASIO authorized service center.

Front

Quick Start Basics

To replace the memory card

Press the memory card and then release it. This will cause it to pop out of the memory card slot slightly. Pull the card out the rest of the way and then insert another one.

• Never remove a card from the camera while the back lamp is flashing green. Doing so can cause the image save operation to fail and even damage the memory card.

To format (initialize) a new memory card

Format a memory card on the camera before using it for the first time.

IMPORTANT!

• Formatting a memory card that already has snapshots or other files on it, will delete its contents. Normally you do not need to format a memory card again. However, if storing to a card has slowed down or if you notice any other abnormality, re-format the card.

• Be sure to use the camera to format a memory card. Formatting a card on a computer will result in a non-SD standard format, which can greatly slow down processing time and cause compatibility, performance, and other problems.

• Before formatting a new Eye-Fi card to use it for the first time, copy the Eye-Fi Manager install files to your computer. Do this before formatting the card.

1. Press [ON/OFF] (Power) to turn on the camera and then press [SET].

2. Use [8] and [2] to select the second Control Panel option from the

bottom (MENU) and then press [SET] (page 32).

3. Use [4] and [6] to select the “Set Up” tab.

4. Use [8] and [2] to select “Format” and then press [6].

5. Use [8] and [2] to select “Format” and then press [SET].

Quick Start Basics

Turning the Camera On and Off

To turn power on

Pressing [ON/OFF] (Power) enters the REC mode so you can record images. Pressing [p] (PLAY) while in the REC mode enters the PLAY mode, which you can use to view snapshots and movies (pages 28, 66).

•Pressing [r] (REC) while in the PLAY mode returns to the REC mode.

• Take care to ensure that nothing is restricting or coming into contact with the lens as it extends. Holding the lens with your hand so it cannot extend creates the risk of malfunction.

• About 10 seconds after you press [p] (PLAY) to enter the PLAY mode, the lens will retract into the camera.

• The Sleep function or Auto Power Off (pages 103,

103) will turn off power automatically if you do not perform any operation for a preset amount of time.

[ON/OFF] (Power)

[p] (PLAY) [r] (REC)

To turn off the camera

Press [ON/OFF] (Power).

NOTE

• You also can configure the camera to turn on or off when you press [r] (REC) or [p] (PLAY) (page 104).

Quick Start Basics

Holding the Camera Correctly

Your images will not come out clearly if you move the camera when you press the shutter button. When pressing the shutter button, be sure to hold the camera as shown in the illustration below, and keep it still by pressing your arms firmly against your sides as you shoot. Holding the camera still, carefully press the shutter button and take care to avoid all movement as the shutter releases and for a few moments after it releases. This is especially important when available lighting is low, which slows down the shutter speed.

Horizontal Vertical

Hold the camera so the flash is above the lens.

NOTE

• Take care that your fingers and the strap do not cover any of the areas indicated in the illustration.

• To protect against accidentally dropping the camera, attach the wrist strap and make sure it is around your fingers or wrist while you are operating the camera.

• Never swing the camera around by its strap.

• The supplied strap is intended for use with this camera only. Never use it for any other purpose.

IMPORTANT!

• Take care to ensure that your fingers are not blocking or are not too close to the flash. Fingers can cause unwanted shadows when using the flash.

Flash

Front lamp

Lens

Microphone

Quick Start Basics

To shoot a snapshot

Selecting an Auto Recording Mode

You can select one of two auto recording modes (Auto or Premium Auto) according to your digital imaging needs.

Auto This is the standard Auto recording mode.

With Premium Auto recording, the camera automatically determines whether you are shooting a subject or scenery, and other conditions. Premium Auto recording delivers higher

Premium Auto

image quality than standard Auto recording.

• Premium Auto recording takes longer to process image data after it is shot than Auto recording.

• It requires more power (and runs down the battery quicker) than Auto.

1. Press [ON/OFF] (Power) to turn on the camera.

The camera will enter the REC mode.

• If the camera is in the PLAY mode, press [r] (REC).

• You also can configure the camera to turn on when you press [r] (REC) or [p] (PLAY) (page 104).

2. Press [SET].

3. Use [8] and [2] to select the bottom Control Panel option (BS) and

then press [SET].

This will display a menu of BEST SHOT scenes (page 50).

4. Use [8], [2], [4], and [6] to select “Auto” or “Premium Auto”, and

then press [SET].

This enters the selected auto recording mode.

Auto recording mode icon

[ON/OFF] (Power)

Remaining Snapshot Memory Capacity (page 126)

Monitor screen

Shutter button

[r] (REC)

[SET]

[4] [6] [8] [2]

Quick Start Basics

To shoot a snapshot

1. Point the camera at the subject.

If you are using Premium Auto, text will appear in the lower right corner of the monitor screen describing the type of shot the camera has detected.

• You can zoom the image, if you want.

Zoom controller

w Wide Angle z Telephoto

2. Half-press the shutter button to

focus the image.

When focus is complete, the camera will beep, the back lamp will light green, and the focus frame will turn green.

Half-press

Press lightly until the button stops.

Beep, beep (Image is in focus.)

Back lamp Focus frame

When you half-press the shutter button, the camera automatically adjusts exposure and focuses on the subject it is currently pointed at. Mastering how much pressure is required for a half-press and a full-press of the shutter button is an important technique for goodlooking images.

• The focus frame in the screen shots

included in this manual is shown at ß. Note that you can change the form of the focus frame, if you want (page 58).

Quick Start Basics

3. Continuing to keep the camera still, press the shutter button the rest of

the way down.

This records the snapshot.

Full-press

Snap (Image is recorded.)

. If the image does not focus...

If the focus frame stays red and the back lamp is flashing green, it means that the image is not in focus (because the subject is too close, etc.). Re-point the camera at the subject and try to focus again.

. Shooting with Auto

If the subject is not in the center of the frame...

“Focus lock” (page 57) is the name of a technique you can use when you want to shoot an image in which the subject to be focused on is not within the focus frame in the center of the screen.

To track the movement of a moving subject

Half-press the shutter button to follow and focus automatically on a moving subject. See “O

Tracking” (page 60) for more information.

. Shooting with Premium Auto

• In addition to shutter speed, aperture, and ISO sensitivity, the camera automatically executes the following operation as required when shooting with Premium Auto. – Auto Focus is normally performed until you half-press the shutter button. – The camera automatically determines the focus point on the screen and focuses

there.

– Face Detection (page 40)

• Shooting with Premium Auto can cause vibration and noise to occur due to lens operation. This does not indicate malfunction.

• In some cases, Premium Auto may not be able to interpret the shooting environment correctly. If this happens, shoot with standard Auto.

Recording a Movie

Press [0] (Movie) to start movie recording. Press [0] (Movie) again to stop movie recording. See page 46 for details.

[0] (Movie)

Quick Start Basics

Viewing Snapshots

Use the following procedure to view snapshots on the camera’s monitor screen.

• For information about how to play back movies, see page 66.

1. Turn on the camera and press

[p] (PLAY) to enter the PLAY mode.

• This will display one of the snapshots currently stored in memory.

• Information about the displayed snapshot also is included (page 10).

• You also can clear the information to view only the snapshot (page 11).

• You can zoom in on the image by sliding the zoom controller towards z (page 67). If you are recording a snapshot that is very important to you, it is recommended that you zoom the image and check its details after recording it.

[p] (PLAY)

2. Use [4] and [6] to scroll between images.

• Holding down either button scrolls at high speed.

[6]

[4]

NOTE

• Half-pressing the shutter button while in the PLAY mode or while a menu screen is displayed will switch directly to the REC mode.

[4]

Quick Start Basics

Deleting Snapshots and Movies

If memory becomes full, you can delete snapshots and movies you no longer need in order to free up storage and record more images.

• In either the REC mode or PLAY mode, you can delete files simply by pressing [ ] (Delete).

IMPORTANT!

• Remember that a file (image) delete operation cannot be undone.

• Deleting an audio snapshot (page 76) deletes both the snapshot and the audio file.

• You cannot delete files while movie or audio recording is in progress.

• The delete menu will not appear if you press [ ] (Delete) while “On” is selected for the camera’s “Ü Disabled” setting (page 104). You can delete files only while “Off” is selected for “Ü Disabled”.

[ ] (Delete)

To delete a single file

1. Press [ ] (Delete).

2. Use [4] and [6] to scroll through the files until the one

you want to delete is displayed.

3. Use [8] and [2] to select “Delete” and then press [SET].

• To delete other files, repeat steps 2 and 3.

• To exit the delete operation, press [ ] (Delete).

Quick Start Basics

To delete specific files

1. Press [ ] (Delete).

2. Use [8] and [2] to select “Delete Files” and then press [SET].

• This displays a file selection screen.

3. Use [8], [2], [4], and [6] to move the selection boundary to the file

you want to delete, and then press [SET].

• This will select the check box of the currently selected file.

4. Repeat step 3 to select other files, if you want. After you are finished

selecting files, press [ ] (Delete).

5. Use [8] and [2] to select “Yes” and then press [SET].

• This deletes the files you selected.

• To exit the delete operation, press [ ] (Delete).

To delete all files

1. Press [ ] (Delete).

2. Use [8] and [2] to select “Delete All Files” and then press [SET].

3. Use [8] and [2] to select “Yes” and then press [SET] to delete all files.

This will cause the message “There are no files” to appear.

Quick Start Basics

+ 102 hidden pages