• Before using it, be sure to read the precautions contained in this User’s Guide.
• Keep the User’s Guide in a safe place for future reference.
• For the most up-to-date information about this product, visit the official EXILIM
Website at http://www.exilim.com/
Accessories
As you unpack your camera, check to make sure that all accessories shown below
are included. If anything is missing, contact your original retailer.
Rechargeable lithium ion
battery (NP-130A)
Micro USB cableNeck strapBasic Reference
USB-AC adaptor
(AD-C53U)
Power cord*
* The shape of the power cord plug varies according to the country or geographic
area where the camera is sold.
2
Attaching the Neck Strap to the Camera
Buckle
Ring
Strap holes
1
To shorten
To lengthen
1. Undo the strap from the buckle
and remove the strap loop
3. Pass the end of the strap
.
2. Attach the loop on the other end
of the strap
on one side of the camera, and
the loop you removed
other side.
. Adjusting the Length of the Strap
You can adjust the length of the strap so it can
be used as a neck strap or a shoulder strap.
to the strap hole
to the
through the strap loop ring
and secure it with the buckle.
1. Pull the strap out at the center
of the buckle in the direction
indicated by
.
2. Pull the strap in one of the
directions indicated by the
illustration to adjust the length.
3
Read this first!
• The contents of this manual are subject to change without notice.
• The contents of this manual have been checked at each step of the production
process. Feel free to contact us if you notice anything that is questionable,
erroneous, etc.
• Any copying of the contents of this User’s Guide, either in part or its entirety, is
forbidden. Except for your own personal use, any other use of the contents of this
manual without the permission of CASIO COMPUTER CO., LTD. is forbidden
under copyright laws.
• CASIO COMPUTER CO., LTD. shall not be held liable for any damages or lost
profits suffered by you or any third party due to the use or malfunction of this
product.
• CASIO COMPUTER CO., LTD. shall not be held liable for any damages, lost
profits, or claims by third parties arising out of the use of the EXILIM Connect
application software.
• CASIO COMPUTER CO., LTD. shall not be held liable for any damages or lost
profits caused by loss of memory contents due to malfunction, repair, or any other
reason.
• Note that the example screens and product illustrations shown in this User’s Guide
may differ somewhat from the screens and configuration of the actual camera.
LCD Panel
The liquid crystal panel of the monitor screen uses high-precision technology that
provides a pixel yield in excess of 99.99%. This means that some very small number
of pixels may not light or may remain lit at all times. This is due to the characteristics
of the liquid crystal panel, and does not indicate malfunction.
Take test shots
Before shooting your final image, shoot a test shot to ensure that the camera is
recording correctly.
Assigning a Recording Function to the Front Shutter Button (Front Shutter). . 106
Assigning Functions to the Function Ring and Control Dial (Key Customize) . 107
Control dial
([8][2][4][6])
(pages 12, 43, 76, 91,
105, 133)
Monitor screen
(pages 13, 33)
blbm
123465
9bk
87
cmcncl ck
bo
co
bnbp bq br
bs
bt
Front
Back
General Guide
The numbers in parentheses indicate the pages where each item is explained.
11
General Guide
. Control Dial
crcpcq
cs
Bottom
Battery/memory card slots (pages 21, 29)
Battery cover
Speaker
Tripod hole
Use this hole when attaching to a tripod.
Control dial
With the control dial, you can perform operations by
pressing the edges of the dial ([8], [2], [4], [6]), and
by rotating the dial.
• Depending on the function, certain operations
cannot be performed using the control dial.
12
General Guide
Monitor Screen Contents and How to Change Them
NOTE
8
9
bl
bk
bp
bq
bm
bn
13567
cl
cp
cn
cm
co
cr
cs
cq
2
4
bo
ckbs
brbt
The monitor screen uses various indicators, icons, and values to keep you informed
of the camera’s status.
• The sample screens in this section are intended to show you the locations of all the
indicators and figures that can appear on the monitor screen in various modes.
They do not represent screens that actually appear on the camera.
. Snapshot Recording (1 Shot)
Movie quality (FHD/STD movie)
(pages 76, 117)/
Recording speed (high speed movie) (page 80)
AF Area (page 111)
Focal distance
(Converted to 35 mm film format.) (page 56)
Image stabilization (page 113)
Zoom (SR) indicator (page 57)
Remaining movie memory
capacity (page 76)
Remaining snapshot memory
capacity (page 233)
Snapshot image size/Quality
(pages 115, 116)
Wireless LAN communication status
(page 159)
Focus frame (pages 34, 111)
Battery level indicator (page 26)
Metering mode (page 54)
Flash (page 52)
Exposure (page 51)
Make-up (page 50)
ISO sensitivity (page 49)
Focus mode (page 47)
White balance (page 45)
• Depending on recording settings, the aperture, shutter speed, and ISO sensitivity
values may not appear on the monitor screen. These values will be red if the Auto
Exposure (AE) is not correct for some reason.
• The folder name and file name in the upper right corner of the monitor screen has
the meaning described below (page 184).
Example: 100-0023: 23rd image file in the folder named “100CASIO”.
Each press of [8] (DISP) will cycle through display settings that
display or hide on-screen information. You can configure separate
settings for the REC mode and PLAY mode.
REC mode
Information onDisplays setting information.
Information offHides setting information.
PLAY mode
Information onDisplays settings when shooting and histogram (page 121).
Information offNo information displayed when shooting.
Monitor Screen Contents and How to Change Them
16
Quick Start Basics
*See pages 19, 65, 106 for more information.
*See page 151 for more information.
*See page 161 for more information.
*See page 136 for more information.
*See page 134 for more information.
What you can do with your CASIO camera
Your CASIO camera is packed with a powerful selection of features and functions to
make recording of digital images easier, including the following main functions.
Self-portrait Shooting
The monitor screen can be tilted up to 180 degrees
upwards, which allows viewing while shooting selfportraits. Self-portrait shooting is also made simpler by
a front shutter button and Motion Shutter feature.
Wireless Connection
Turns your smartphone into a camera remote
controller and allows you to send images recorded with
your camera to your smartphone.
One Time Share
Share selected snapshots for viewing on smartphones
that are not paired with the camera.
The Scene app needs to be installed on the
smartphone in order to use One Time Share.
Highlight Photo
You can configure camera settings to automatically
select snapshot highlights and generate a collage of
them.
Highlight Movie
You can configure camera settings to automatically
select snapshot and movie highlights, and create a
movie of them.
17
Quick Start Basics
Premium Auto Pro
*See page 33 for more information.
*See page 80 for more information.
*See page 73 for more information.
Select Premium Auto Pro recording and the
camera automatically determines whether you
are shooting a subject or scenery, and other
conditions. Premium Auto Pro delivers higher
image quality than standard Auto.
High Speed Movie
Movies can be recorded at up to 1000 frames per
second. This makes it possible to clearly view
phenomena that are invisible to the human eye, in
slow motion.
Selfie Art
This function lets you select a scene and shoot selfies
with various art effects applied.
18
Quick Start Basics
Tilting the Monitor Screen
180 degrees
90 degrees
The monitor screen can be tilted upwards up
to 180 degrees. This means you can position
the monitor screen so it faces in the same
direction as the lens, for easy composition of
self-portraits. You can also tilt the monitor
screen upwards 90 degrees, which means
you can easily shoot from a low angle
without straining your neck to view the
monitor screen.
. What you can do with the camera...
Shoot self-portraitsLow-angle shots
You can position the monitor screen so it
faces in the same direction as the lens,
for easy composition of self-portraits.
The tilt angle of the monitor screen can
be adjusted for each composition of
images from various low angles.
By holding the camera upside down, you
can angle the monitor screen in a way that
allows you to shoot from high angles. In
this case, the camera will automatically
rotate on-screen information and the
displayed image 180 degrees.
High-angle shots
19
Quick Start Basics
. Tilting the Monitor Screen
NOTE
A
OKNG
A
As shown in the figure below, pull upwards on the bottom center of the monitor
screen at point
Keep lifting and it will tilt upwards up to 180 degrees.
• Do not pull downwards from the top of the monitor screen. Be sure to pull upwards
from the bottom of the monitor screen as shown in the figure.
IMPORTANT!
• Under factory default settings, the camera will turn on automatically whenever the
monitor screen is tilted. See page 192 for information about configuring the camera
so it does not turn on when the monitor screen is tilted upwards.
• When returning the monitor screen to the back of the camera, take care so you do
not catch your fingers between the top or bottom of the monitor screen and the
camera.
• Do not subject the monitor screen to strong impact. Doing so can damage it.
• Be sure to return the monitor screen to its normal position to the back of the
camera when you are not using it.
.
. Returning the Monitor Screen to Its Normal Position
As shown in the figure, holding the monitor screen at point
, rotate the screen downwards to the back of the
camera.
20
Quick Start Basics
First, charge the battery prior to use.
Battery cover
CASIO logo
Stopper
Battery
OK
NG
Note that the battery of a newly purchased camera is not charged. Perform the steps
below to load the battery into the camera and charge it.
• Your camera requires a special CASIO rechargeable lithium ion battery (NP-130A)
for power. Never try to use any other type of battery.
To load the battery
1. Open the battery cover.
2. Load the battery.
With the CASIO logo on the battery
facing downwards (in the direction
of the lens), hold the stopper next
to the battery in the direction
indicated by the arrow as you slide
the battery into the camera. Press
the battery in until the stopper
secures it in place.
3. Close the battery cover.
21
Quick Start Basics
To replace the battery
IMPORTANT!
Stopper
4
3
2
1
USB-AC adaptor
(AD-C53U)
u mark of the small (micro USB) connector
facing the monitor screen side of the camera.
[USB] port
Power cord
Micro USB cable
(included with camera)
1. Press [ON/OFF] (Power) to
turn off the camera and then
open the battery cover.
2. Remove the current battery
and load a new one.
3. Close the battery cover.
• The back lamp (page 11) will flash green for some time after you press [ON/OFF]
(Power) to turn off the camera. Never remove the battery while the back lamp is
flashing green. Doing so can result in corruption or loss of data in camera memory.
Charge the Battery
You can use either of the two following methods to charge the camera’s battery.
• USB-AC adaptor (page 22)
• USB connection to a computer (Using the included micro USB cable.) (page 24)
. To charge with the USB-AC adaptor
The adaptor lets you charge the battery while it is loaded in the camera.
While the camera is turned off, connect in the sequence shown below.
Charging time: Approximately 240 minutes
• When disconnecting the USB-AC adaptor from the camera, be sure to disconnect
from the camera first.
22
Quick Start Basics
Back Lamp Operation
IMPORTANT!
Back lamp
Lamp StatusDescription
Lit RedCharging
Abnormal ambient temperature,
Flashing Red
USB-AC adaptor problem, or battery
problem (page 218)
OffCharging complete
• A battery that has not been used for a long time and/or ambient temperature can
cause charging to take longer than normal. These conditions may also cause the
back lamp to flash red. If this happens, refer to page 218.
• Make sure that you insert the cable connector into the [USB] port until you feel it
click securely into place. Failure to insert the connector fully can result in poor
communication or malfunction.
• Note that even while the connector is fully inserted, you
still will be able to see the metal part of the connector as
shown in the illustration.
• Pressing [ON/OFF] (Power) while the USB-AC adaptor is
connected to the camera will turn on the camera with
power being supplied by the battery. Because of this,
charging will stop.
• The USB-AC adaptor will become warm during charging.
This is normal and does not indicate malfunction.
• The shape of the power plug depends on each country or geographic area.
23
Quick Start Basics
. To charge using a USB connection to a computer
IMPORTANT!
USB
2
1
Micro USB cable
(included with camera)
u mark of the small (micro USB) connector facing the
monitor screen side of the camera.
[USB] port
USB port
Computer
(power turned on)
Back lamp
USB connection lets you charge the battery while it is loaded in the camera.
While the camera is turned off, connect in the sequence shown below (
• If the camera is on, press [ON/OFF] (Power) to turn it off before connecting it to
your computer.
,
).
Back Lamp Operation
Lamp StatusDescription
Lit Red,
[Lit/Flashing Amber]
Charging
Abnormal ambient temperature,
Flashing Red
charging taking abnormally long, or
battery problem (page 218)
Off, [Lit Green]Charging complete
• Lamp statuses in parentheses above indicate operations when the camera is on
while charging over a USB connection with a computer.
• The first time you connect the camera to your computer with the USB cable, an
error message may appear on your computer. If this happens, disconnect and then
reconnect the USB cable.
• A battery that has not been used for a long time, certain types of computers, and
connection conditions can cause charging to take longer than normal. These
conditions may also cause the back lamp to flash red. If this happens, refer to page
218.
• For faster charging, use of the supplied USB-AC adaptor is recommended.
• You cannot use the camera to shoot images while it is being charged over a
computer USB connection. If you want to shoot with the camera, disconnect the
USB cable.
24
Quick Start Basics
• If you turn on the camera while charging over a USB connection to a computer is in
progress, the camera will establish a USB connection with the computer. Though
charging normally should continue at this time, certain types of computers or
connection environments may stop charging if supply power is low. This will be
indicated by the camera’s back lamp lighting green.
• Charging is not performed while the connected computer is in the hibernate mode.
Other Charging Precautions
• With the two charging methods described above, you can charge the camera’s
battery (NP-130A) without removing it from the camera. You also can charge the
battery using an optionally available charger unit (BC-130L).
• This model can be charged only via from USB 2.0 specification USB port only.
• USB charging devices and power supply devices are subject to fixed standards.
Use of an inferior device or a device that is not up to standard can cause
malfunction and/or failure of your camera.
• Operation is not guaranteed in the case of a computer built or modified by you.
Even in the case of a commercially available computer, certain USB port
specifications may make it impossible to charge via the USB cable.
• A battery that is still warm immediately after normal use may not charge fully. Give
the battery time to cool before charging it.
• A battery discharges slightly even when it is not loaded in the camera. Because of
this, it is recommended that you charge the battery immediately before you need to
use it.
• Charging the camera’s battery may cause interference with TV and radio reception.
If this happens, plug the USB-AC adaptor into an outlet that is further away from
the TV or radio.
• Actual charging time depends on current battery capacity and charging conditions.
• Do not use the USB-AC adaptor with any other device.
• Never use the power cord with another device.
• Use only the USB-AC adaptor and USB cable specified in this manual for charging.
Use of any other type of devices may result in improper charging.
25
Quick Start Basics
Checking Remaining Battery Power
As battery power is consumed, a battery indicator on the monitor screen indicates
remaining power as shown below.
Remaining PowerHighLow
Battery Indicator***
Indicator ColorWhite* White*Red*Red
indicates battery power is low. Charge the battery as soon as possible.
Recording is not possible when is indicated. Charge the battery immediately.
• The level shown by the battery indicator may change when you switch between the
REC mode and PLAY mode.
• Leaving the camera for about 20 days with no power supplied while the battery is
dead will cause its date and time settings to be cleared. A message telling you to
configure time and date settings will appear the next time you turn on the camera
after restoring power. When this happens, configure date and time settings (page
194).
• See page 238 for information about battery life and number of shots.
Battery Power Conservation Tips
• Entering the “ECO Mode” (page 187) enables low-power operation. Note that lowpower operation decreases monitor screen brightness.
• Enable the Auto Power Off (page 191) and the Sleep (page 191) features to protect
against wasting battery power when you forget to turn off the camera.
• Select “Off” for “Continuous AF” (page 113).
Configuring Basic Settings the First Time You Turn On the
Camera
The first time you load a battery into the camera, a screen appears for configuring the
display language, date, and time settings. Failure to set the date and time correctly
will cause the wrong date and time data to be recorded with images.
IMPORTANT!
• A screen for language selection will not appear in step 2 of the procedure below if
you purchased a camera intended for the Japanese market. To change the display
language from Japanese in this case, use the procedure under “Specifying the
Display Language (Language)” (page 195). Note that a version of this manual in
the language you select may not be included with a camera intended for the
Japanese market.
• Camera models sold in certain geographic areas may not support display language
selection.
26
Quick Start Basics
1. Press [ON/OFF] (Power) to turn on the
NOTE
[ON/OFF] (Power)
camera.
2. Use [8] and [2] to select the language
you want and then press [SET].
3. Use [8] and [2] to select a date style
and then press [SET].
Example: July 10, 2016
YY/MM/DD
DD/MM/YY
MM/DD/YY
* 16/7/10
* 10/7/16
* 7/10/16
4. Set the date and the time.
Use [4] and [6] to select the setting you want to
change and then use [8] and [2] to change it.
To switch between 12-hour and 24-hour format, use
[4] and [6] to select “24h” and then use [8] and [2]
to change the setting.
5. After setting the date and time, use [4] and [6]
to select “Apply” and then press [SET].
If you make a mistake configuring display language, date, or time settings with the
above procedure, refer to the following pages for information about how to correct
the settings.
– Display language: page 195
– Date and time: page 194
• Each country controls its local time offset and the use of summer time, and so they
are subject to change.
• Removing the battery from the camera too soon after configuring time and date
settings for the first time can cause the settings to be reset to their factory defaults.
Do not remove the battery for at least 24 hours after configuring settings.
27
Quick Start Basics
Preparing a Memory Card
Though the camera has built-in memory, its capacity is small. To shoot a large
number of images or long movies, you will need to use a commercially available
memory card. When no memory card is loaded, images are saved to built-in memory.
• For information about memory card capacities, see page 233.
Supported Memory Cards
Your camera supports use of the following types of SD memory
cards.
– SD Memory Card (Up to 2GB)
– SDHC Memory Card (2GB to 32GB)
– SDXC Memory Card (32GB to 2TB)
• The above are supported memory card types as of December 2015.
• Values in parentheses are specification values.
• Note that the ability to use any particular card with this camera, even if it satisfies
the above capacity and type requirements, is not guaranteed.
. Memory Card Handling Precautions
Certain types of memory cards can slow down processing speeds. In particular, highquality movies may not be able to be stored correctly. A slow memory card can take
too much time to record data and result in breaks in the image and/or audio during
playback. When this happens a yellow “Y” indicator will appear on the monitor
screen.
28
Quick Start Basics
To load a memory card
FrontBack
Back
1. Press [ON/OFF] (Power) to turn off
the camera and then open the
battery cover.
2. Load a memory card.
Positioning the memory card so its back
is facing upwards (towards the monitor
screen side of the camera), slide it into
the card slot all the way in until you hear
it click securely into place.
3. Close the battery cover.
IMPORTANT!
• Never insert anything besides a supported memory card (page 28) into the memory
card slot.
• Should water or any foreign object ever get into the card slot, immediately turn off
the camera, remove the battery, and contact your retailer or nearest CASIO
authorized service center.
29
Quick Start Basics
To replace the memory card
IMPORTANT!
Back lamp
Press the memory card and then release it.
This will cause it to pop out of the memory
card slot slightly. Pull the card out the rest
of the way and then insert another one.
IMPORTANT!
• Turn off the camera before replacing the
memory card.
• The back lamp (page 11) will flash green
for some time after you press [ON/OFF]
(Power) to turn off the camera. Never remove the memory card while the back
lamp is flashing green. Doing so can cause the image save operation to fail and
even damage the memory card.
To format (initialize) a new memory card
Format a memory card on the camera before using it for the first time.
• Formatting a memory card that already has snapshots or other files on it, will delete
its contents. Normally you do not need to format a memory card again. However, if
storing to a card has slowed down or if you notice any other abnormality, re-format
the card.
• Be sure to use the camera to format a memory card. Formatting a card on a
computer will result in a non-SD standard format, which can greatly slow down
processing time and cause compatibility, performance, and other problems.
1. Turn on the camera and press [MENU].
2. Press [4], use [8] and [2] to select the “
¥
SETTING” tab, and then
press [6].
3. Use [8] and [2] to select “Format” and then press [6].
4. Use [8] and [2] to select “Format” and then press [SET].
5. Use [8] and [2] to select “Yes” and then press [SET].
30
Quick Start Basics
Loading...
+ 210 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.