• Before using it, be sure to read the precautions contained in this User’s Guide.
• Keep the User’s Guide in a safe place for future reference.
• For the most up-to-date information about this product, visit the official EXILIM
Website at http://www.exilim.com/
To go to “Getting the Most Out of Dynamic Photo” click here!
1
Unpacking
As you unpack your camera, check to make sure that all items shown below are
included. If anything is missing, contact your original retailer.
Digital camera
Rechargeable lithium ion
battery (NP-80)
To attach the strap to the camera
Charger unit (BC-81L)
Attach strap here.
1
Power cordStrap
USB cableAV cableCD-ROMBasic Reference
2
2
Read this first!
• The contents of this manual and the bundled Basic Reference are subject to
change without notice.
• The contents of this manual have been checked at each step of the production
process. Feel free to contact us if you notice anything that is questionable,
erroneous, etc.
• Any copying of the contents of this User’s Guide, either in part or its entirety, is
forbidden. Except for your own personal use, any other use of the contents of this
manual without the permission of CASIO COMPUTER CO., LTD. is forbidden
under copyright laws.
• CASIO COMPUTER CO., LTD. shall not be held liable for any damages or lost
profits suffered by you or any third party due to the use or malfunction of this
product.
• CASIO COMPUTER CO., LTD. shall not be held liable for any damages, lost
profits, or claims by third parties arising out of the use of Photo Transport, Dynamic
Photo Manager, or YouTube Uploader for CASIO.
• CASIO COMPUTER CO., LTD. shall not be held liable for any damages or lost
profits caused by loss of memory contents due to malfunction, repair, or any other
reason.
• Note that the example screens and product illustrations shown in this User’s Guide
may differ somewhat from the screens and configuration of the actual camera.
LCD Panel
The liquid crystal panel of the monitor screen uses high-precision technology that
provides a pixel yield in excess of 99.99%. This means that some very small number
of pixels may not light or may remain lit at all times. This is due to the characteristics
of the liquid crystal panel, and does not indicate malfunction.
Take a few test shots
Before shooting your final image, shoot a test shot to ensure that the camera is
recording correctly.
The monitor screen uses various indicators, icons, and values to keep you informed
of the camera’s status.
• The sample screens in this section are intended to show you the locations of all the
indicators and figures that can appear on the monitor screen in various modes.
They do not represent screens that actually appear on the camera.
. Snapshot Recording
Remaining snapshot memory capacity
cp
co
cn
cm
341657
2
ckcl
bt
89
brbs
bk
bl
bm
bn
bo
bp
bq
1
(page 175)
Remaining movie memory capacity (page 50)
2
Recording mode (page 25)
3
White balance setting (page 83)
4
Continuous shutter (page 70)
5
Image deterioration indicator (page 48)
6
Metering mode (page 84)
7
Snapshot image size (page 32)
8
Snapshot image quality (page 81)
9
Movie image quality (page 35)
bk
Flash (page 36)
bl
Self-timer (page 38)
bm
AF Area (page 39)
bn
ISO sensitivity (page 41)
bo
easy Mode (page 41)
bp
Face Detection/Make-up/Landscape
bq
(pages 43, 45, 46)
Date/time (page 47)
br
Timestamp indicator (page 144)
bs
Exposure compensation (page 82)
bt
Focus frame (pages 26, 40)
ck
Battery level indicator (page 19)
cl
Histogram (page 150)
cm
Anti Shake (page 77)
cn
Auto shutter (page 73)
co
Focus mode (page 66)
cp
11
. Shutter Button Half-pressed
Recording mode (page 25)
2
3
1
Flash (page 36)
2
ISO sensitivity (page 41)
3
Aperture value
4
Shutter speed
5
Focus frame (pages 26, 40)
6
1
6
4
5
NOTE
• If the current aperture, shutter speed, ISO sensitivity, or Auto Exposure is not
correct, the setting will turn orange when you half-press the shutter button.
easy Mode
.
321
4
7
5
Flash (page 36)
1
Self-timer (page 38)
2
Remaining snapshot memory capacity
3
(page 175)
Snapshot image size (page 32)
4
Date/time (page 47)
5
Battery level indicator (page 19)
6
Focus frame (pages 26, 40)
7
6
12
. Movie Recording
123
9
8
76
. Snapshot Viewing
2
bq
bp
boblbkbmbn
. Movie Playback
1
23
7
Flash (page 36)
1
Recording mode (page 50)
2
4
5
31
4
5
6
7
8
9
4
5
White balance setting (page 83)
3
Remaining movie memory capacity (page 50)
4
Movie recording time (page 50)
5
Exposure compensation (page 82)
6
Battery level indicator (page 19)
7
Histogram (page 150)
8
Anti Shake (page 77)
9
File type
1
Protect indicator (page 106)
2
Folder name/file name (page 139)
3
Snapshot image quality (page 81)
4
Snapshot image size (page 32)
5
ISO sensitivity (page 41)
6
Aperture value
7
Shutter speed
8
Date/time (page 47)
9
Metering mode (page 84)
bk
White balance setting (page 103)
bl
Flash (page 36)
bm
Recording mode
bn
Battery level indicator (page 19)
bo
Histogram (page 150)
bp
Exposure compensation (page 82)
bq
File type
1
Protect indicator (page 106)
2
Folder name/file name (page 139)
3
Movie recording time (page 87)
4
Movie image quality (page 35)
5
Date/time (page 47)
6
Battery level indicator (page 19)
7
6
13
Quick Start Basics
What is a digital camera?
A digital camera stores images on a memory card, so you can record and
delete images a countless number of times.
Record
Delete
You can use the images you record in a variety of different ways.
Store images on your
computer.
Print images.Attach images to e-mail.
14
Play
Quick Start Basics
What you can do with your CASIO camera
Your CASIO camera is packed with a powerful selection of features and functions to
make recording of digital images easier, including the following three main functions.
Dynamic Photo
Extract a moving subject out of a series of Continuous Shutter images you
have shot and insert them into another image to create a Dynamic Photo
image that features the moving subject.
See page
111 for more information.
Make-up Mode/Landscape Mode
The Make-up Mode smoothes the skin texture of the subject
and softens facial shadows caused by harsh sunlight for
better looking portraits.
The Landscape Mode makes colors more vivid and
performs other processes to enhance the beauty of natural
scenery.
BEST SHOT
See pages
Simply select the sample scene you want and the
camera sets up automatically. Then all you need do is
press the shutter button for perfect images.
An AUTO BEST SHOT mode automatically selects the
appropriate BEST SHOT sample scene based on
current shooting conditions.
45, 46 for more information.
See page
55 for more information.
15
Quick Start Basics
First, charge the battery prior to use.
Note that the battery of a newly purchased camera is not charged. Perform the steps
under “To charge the battery” to bring the battery to a full charge.
• Your camera requires a special CASIO rechargeable lithium ion battery (NP-80) for
power. Never try to use any other type of battery.
To charge the battery
1. Positioning the positive
+
and
negative - terminals of the battery
with those of the charger unit, load
the battery into the charger unit.
2. Plug the charger unit into a
household power outlet.
About 210 minutes are required to
reach full charge. The [CHARGE]
lamp will go out when charging is
complete. Unplug the power cord
from the power outlet and then
remove the battery from the charger.
Lamp StatusDescription
Lit RedCharging
Flashing Red
OffCharging complete
Abnormal ambient temperature, charger problem, or
battery problem (page 159)
[CHARGE] lamp
16
Quick Start Basics
Other Charging Precautions
• Use the special charger (BC-81L if included with camera, BC-80L if purchased
separately) to charge the special lithium ion battery (NP-80). Never use any other
type of charger device. Attempting to use a different charger can result in
unexpected accident.
• A battery that is still warm due to normal use may not charge fully. Give the battery
time to cool before charging it.
• A battery discharges slightly even when it is not loaded in the camera. Because of
this, it is recommended that you charge the battery immediately before you need to
use it.
• Charging the camera’s battery may cause interference with TV and radio reception.
If this happens, plug the charger into an outlet that is further away from the TV or
radio.
• Actual charging time depends on current battery capacity and charging conditions.
17
Quick Start Basics
To load the battery
1. Open the battery cover.
Pressing the battery cover, slide it in the direction
indicated by the arrow.
1
2
2. Load the battery.
With the EXILIM logo on the
battery facing upwards (in the
direction of the monitor
screen), hold the stopper next
to the battery in the direction
indicated by the arrow as you
slide the battery into the
camera. Press the battery in
until the stopper secures it in
place.
Battery contacts
3. Close the battery cover.
Pressing the battery cover against the camera, slide
it closed.
• For information about how to replace the battery,
see page 160.
EXILIM logo
Stopper
Front
Back
2
1
18
Quick Start Basics
Checking Remaining Battery Power
As battery power is consumed, a battery indicator on the monitor screen indicates
remaining power as shown below.
Remaining PowerHighLow
Battery Indicator***
Indicator ColorCyan* Amber*Red*Red
indicates battery power is low. Charge the battery as soon as possible.
Recording is not possible when is indicated. Charge the battery immediately.
• The level shown by the battery indicator may change when you switch between the
REC mode and PLAY mode.
• The camera date and time display will not be correct if the camera is left for about
one day with no power supplied while the battery is dead. If this happens, load new
battery and then set the correct time and date (page 145).
• See page 179 for information about battery life and memory capacity.
Battery Power Conservation Tips
• When you do not need to use the flash, select ? (Flash Off) for the flash setting
(page 36).
• Enable the Auto Power Off and the Sleep features to protect against wasting
battery power when you forget to turn off the camera (pages 146, 147).
19
Quick Start Basics
Configuring Basic Settings the First Time You Turn On the
Camera
The first time you load a battery into the camera, a screen appears for configuring the
display language, date, and time settings. Failure to set the date and time correctly
will cause the wrong date and time data to be recorded with images.
IMPORTANT!
• A screen for language selection will not appear in step 2 of the procedure below if
you purchased a camera intended for the Japanese market. To change the display
language from Japanese in this case, use the procedure under “Specifying the
Display Language (Language)” (page 146). Note that a version of this manual in
the language you select may not be included with a camera intended for the
Japanese market.
[ON/OFF] (Power)
1. Press [ON/OFF] (Power) to turn on
the camera.
[
2. Use [8], [2], [4], and [6] to select
the language you want and then
[BS]
SET
press [SET].
3. Use [8] and [2] to select a date style and then press [SET].
Use [4] and [6] to select the setting you want to
change and then use [8] and [2] to change it.
To switch between 12-hour and 24-hour format, press
[BS].
]
5. After setting the date and time, use [4] and [6]
to select “Apply” and then press [SET].
If you make a mistake configuring display language, date, or time settings with the
above procedure, refer to the following pages for information about how to correct
the settings.
– Display language: Page 146
– Date and time: Page 145
20
Quick Start Basics
NOTE
• Each country controls its local time offset and the use of summer time, and so they
are subject to change.
• Removing the battery from the camera too soon after configuring time and date
settings for the first time can cause the settings to be reset to their factory defaults.
Do not remove the battery for at least 24 hours after configuring settings.
Preparing a Memory Card
Though the camera has built-in memory that can be used to store images and
movies, you probably will want to purchase a commercially available memory card for
greater capacity. The camera does not come with a memory card. Images recorded
while a memory card is loaded are saved to the memory card. When no memory card
is loaded, images are saved to built-in memory.
• For information about memory card capacities, see page 175.
Supported Memory Cards
– SD Memory Card
– SDHC Memory Card
Use one of the above types of memory card.
To load a memory card
1. Press [ON/OFF] (Power) to turn off the camera
and then open the battery cover.
Pressing the battery cover, slide it in the direction
indicated by the arrow.
1
2
2. Load a memory card.
Positioning the memory card so its
back is facing upwards (towards the
monitor screen side of the camera),
slide it into the card slot all the way in
until you hear it click securely into
place.
FrontBack
21
Back
Quick Start Basics
3. Close the battery cover.
Pressing the battery cover against the camera, slide
it closed.
• For information about how to replace the memory
card, see page 161.
IMPORTANT!
• Never insert anything besides a supported memory card (page 21) into the memory
card slot.
• Should water or any foreign object ever get into the card slot, immediately turn off
the camera, remove the battery, and contact your retailer or nearest CASIO
authorized service center.
To format (initialize) a new memory card
You need to format a new memory card before using it for the first time.
2
1. Turn on the camera and press [MENU].
2. Select the “Set Up” tab, select “Format” and then press [6].
3. Use [8] and [2] to select “Format” and then press [SET].
IMPORTANT!
• Formatting a memory card that already has snapshots or other files on it, will delete
its contents. Normally you do not need to format a memory card again. However, if
storing to a card has slowed down or if you notice any other abnormality, re-format
the card.
• Be sure to use the camera to format a memory card. Formatting a memory card on
a computer and then using it in the camera can slow down data processing by the
camera. In the case of an SD or SDHC memory card, formatting on a computer can
result in non-conformity with the SD format, causing problems with compatibility,
operation, etc.
• Before formatting a new Eye-Fi card to use it for the first time, copy the Eye-Fi
Manager install files to your computer. Do this before formatting the card.
1
22
Quick Start Basics
Turning the Camera On and Off
To turn power on
To enter the REC mode, press [ON/OFF] (Power) or [r]
(REC). To enter the PLAY mode, press [p] (PLAY).
The back lamp will light (green) momentarily and the
camera will turn on. If you are entering the REC mode,
the lens will extend from the camera at this time.
[ON/OFF] (Power)
• Take care to ensure that nothing is restricting or
coming into contact with the lens as it extends. Holding
the lens with your hand so it cannot extend creates the
Back lamp
risk of malfunction.
•Pressing [p] (PLAY) while in the REC mode switches
to the PLAY mode. The lens retracts about 10 seconds
after switching modes.
• The Sleep function or Auto Power Off (pages 146, 147)
will turn off power automatically if you do not perform
any operation for a preset amount of time.
[p]
(PLAY)
[r]
(REC)
To turn off the camera
Press [ON/OFF] (Power).
• You can configure the camera so power does not turn on when you press [r]
(REC) or [p] (PLAY). You also can configure the camera to turn off when you
press [r] (REC) or [p] (PLAY) (page 147).
23
Quick Start Basics
Holding the Camera Correctly
Your images will not come out clearly if you move the camera when you press the
shutter button. When pressing the shutter button, be sure to hold the camera as
shown in the illustration below, and keep it still by pressing your arms firmly against
your sides as you shoot.
Holding the camera still, carefully press the shutter button and take care to avoid all
movement as the shutter releases and for a few moments after it releases. This is
especially important when available lighting is low, which slows down the shutter
speed.
HorizontalVertical
Hold the camera so the flash is
above the lens.
NOTE
• Take care that your fingers and
the strap do not cover any of the
areas indicated in the illustration.
• To protect against accidentally
dropping the camera, attach the
wrist strap and make sure it is
around your fingers or wrist while
you are operating the camera.
• Never swing the camera around
by its strap.
• The supplied strap is intended
for use with this camera only.
Never use it for any other
purpose.
Flash
Front lamp
Lens
Microphone
Strap
24
Quick Start Basics
To shoot a snapshot
1. Press [r] (REC) to turn on the camera.
Make sure R is on the display. If it isn’t, see page 55.
Snapshot mode icon
Remaining Snapshot Memory
Capacity (page 175)
2. Point the camera at
the subject.
You can zoom the
image, if you want.
Zoom controller
Monitor screen
Shutter button
[r] (REC)
w Wide Anglez Telephoto
25
Quick Start Basics
3. Half-press the shutter button to
focus the image.
When focus is complete, the camera
will beep, the back lamp will light
green, and the focus frame will turn
green.
Back lamp
Focus frame
Half-press
Press lightly
until the
button stops.
Beep, beep (Image is in focus.)
When you half-press the shutter button, the
camera automatically adjusts exposure and
focuses on the subject it is currently pointed
at. Mastering how much pressure is required
for a half-press and a full-press of the shutter
button is an important technique for goodlooking images.
• The focus frame in the screen shots
included in this manual is shown at ß.
Note that you can change the form of the
focus frame, if you want (page 69).
4. Continuing to keep the camera still, press the shutter button the rest of
the way down.
This records the snapshot.
Full-press
Snap (Image is recorded.)
Recording a Movie
Press [0] (Movie) to start
movie recording. Press
[0] (Movie) again to stop
movie recording. See
page 50 for details.
[0] (Movie)
26
Quick Start Basics
. Using Quick Shutter
Fully pressing the shutting button without waiting for Auto Focus to operate will record
using Quick Shutter (page 78).
• With Quick Shutter, the camera focuses faster than normal Auto Focus, which
means you can capture quick moving action more easily. Note, however, that some
images may be out of focus when Quick Shutter is used.
• Whenever possible, take a little extra time to half-press the shutter button in order
to ensure proper focus.
. If the image does not focus...
If the focus frame stays red and the back lamp is flashing green, it means that the
image is not in focus (because the subject is too close, etc.). Re-point the camera at
the subject and try to focus again.
. If the subject is not in the center of the frame...
“Focus lock” (page 68) is the name of a technique you can use when you want to
shoot an image in which the subject to be focused on is not within the focus frame in
the center of the screen.
. To track the movement of a moving subject
Half-press the shutter button to follow and focus automatically on a moving subject.
See “Ë
Tracking” (page 39) for more information.
27
Quick Start Basics
Viewing Snapshots
Use the following procedure to view snapshots on the camera’s monitor screen.
• For information about how to play back movies, see page 87.
1. Press [p] (PLAY) to enter the
[p] (PLAY)
PLAY mode.
• This will display one of the
snapshots currently stored in
memory.
• Information about the displayed
snapshot also is included (page
175).
• You also can clear the information to view only the snapshot (page 150).
• You can zoom in on the image by sliding the zoom controller towards z (page
91). If you are recording a snapshot that is very important to you, it is
recommended that you zoom the image and check its details after recording it.
2. Use [4] and [6] to scroll between images.
• Holding down either button scrolls at high speed.
[6]
[6]
[4]
NOTE
• Half-pressing the shutter button while in the PLAY mode or while a menu screen is
displayed will switch directly to the REC mode.
28
[4]
Quick Start Basics
Deleting Images
If memory becomes full, you can delete images you no longer need to free up storage
and record more images.
IMPORTANT!
• Remember that a file (image) delete operation cannot be undone.
• Deleting an audio snapshot (page 109) deletes both the snapshot and the audio
file.
To delete a single file
1. Press [p] (PLAY) to enter the PLAY mode and then press
[2] ().
2. Use [4] and [6] to scroll through the files until the one you want to
delete is displayed.
3. Use [8] and [2] to select “Delete” and then press [SET].
• To delete other files, repeat steps 2 and 3.
• To exit the delete operation, press [MENU].
To delete all files
1. Press [p] (PLAY) to enter the PLAY mode and then press [2] ().
2. Use [8] and [2] to select “Delete All Files” and then press [SET].
3. Use [8] and [2] to select “Yes” and then press [SET] to delete all files.
This will cause the message “There are no files” to appear.
29
Quick Start Basics
Snapshot Shooting Precautions
Operation
• Never open the battery cover while the back lamp is flashing green. Doing so can
result in the image you just shot being saved incorrectly, damage to other images
stored in memory, malfunction of the camera, etc.
• If unwanted light is shining directly onto the lens, shade the lens with your hand
when shooting an image.
Monitor Screen when Shooting Snapshots
• Subject brightness conditions can cause monitor screen response to slow and can
cause digital noise in the monitor screen image.
• The image that appears on the monitor screen is for image composition. The actual
image will be recorded at the quality set for the image quality setting (page 81).
Shooting Indoors under Fluorescent Lighting
• Minute flickering of fluorescent lighting can affect the brightness or color of an
image.
Auto Focus Restrictions
• Any of the following can make proper focus impossible.
– Solid color wall or other very low contrast subject
– Strongly back lit subject
– Very shiny subject
– Blinds or other subject with a repeating horizontal pattern
– Multiple subjects at varying distances from the camera
– Subject in a dark location
– Camera movement while shooting
– Fast-moving subject
– Subjects outside the focus range of the camera
• If you cannot focus properly, try using focus lock (page 68) or Manual Focus (page
66).
30
Quick Start Basics
Loading...
+ 164 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.