• Before using it, be sure to read the precautions contained in this User’s Guide.
• Keep the User’s Guide in a safe place for future reference.
• For the most up-to-date information about this product, visit the official EXILIM
Website at http://www.exilim.com/
1
Unpacking
As you unpack your camera, check to make sure that all items shown below are
included. If anything is missing, contact your original retailer.
Digital camera
* The shape of the power cord plug
varies according to country or
geographic area.
Rechargeable lithium ion
battery (NP-40)
To attach the strap to the camera
Charger unit (BC-31L)
Attach strap
here.
Power cordStrap
USB cableAV cableCD-ROMBasic Reference
2
Read this first!
• The contents of this manual are subject to change without notice.
• The contents of this manual have been checked at each step of the production
process. Feel free to contact us if you notice anything that is questionable,
erroneous, etc.
• Any copying of the contents of this User’s Guide, either in part or its entirety, is
forbidden. Except for your own personal use, any other use of the contents of this
manual without the permission of CASIO COMPUTER CO., LTD. is forbidden
under copyright laws.
• CASIO COMPUTER CO., LTD. shall not be held liable for any damages or lost
profits suffered by you or any third party due to the use or malfunction of this
product.
• CASIO COMPUTER CO., LTD. shall not be held liable for any damages, lost
profits, or claims by third parties arising out of the use of Photo Loader with HOT
ALBUM, Photo Transport, or YouTube Uploader for CASIO.
• CASIO COMPUTER CO., LTD. shall not be held liable for any damages or lost
profits caused by loss of memory contents due to malfunction, repair, or any other
reason.
• Note that the example screens and product illustrations shown in this User’s Guide
may differ somewhat from the screens and configuration of the actual camera.
LCD Panel
The liquid crystal panel of the monitor screen uses high-precision technology that
provides a pixel yield in excess of 99.99%. This means that some very small number
of pixels may not light or may remain lit at all times. This is due to the characteristics
of the liquid crystal panel, and does not indicate malfunction.
Take a few test shots
Before shooting your final image, shoot a test shot to ensure that the camera is
recording correctly.
A digital camera stores images on a memory card, so you can record and
delete images a countless number of times.
Record
Delete
You can use the images you record in a variety of different ways.
Store images on your
computer.
Print images.Attach images to e-mail.
9
Play
Quick Start Basics
What you can do with your CASIO camera
Your CASIO camera is packed with a powerful selection of features and functions to
make recording of digital images easier, including the following three main functions.
Auto Shutter
The camera releases the shutter automatically
when it detects the camera is still, the subject is
smiling, etc.
See page
30 for more information.
Make-up Mode
Point the camera at a person and it automatically
detects the person’s face for bright, beautiful
portraits every time.
See page
46 for more information.
BEST SHOT
Simply select the sample scene you want and the
camera sets up automatically. Then all you need
do is press the shutter button for perfect images.
An AUTO BEST SHOT mode automatically selects
the appropriate BEST SHOT sample scene based
on current shooting conditions.
See page
52 for more information.
10
Quick Start Basics
First, charge the battery prior to use.
Note that the battery of a newly purchased camera is not charged. Perform the steps
under “To charge the battery” to bring the battery to a full charge.
• Your camera requires a special CASIO rechargeable lithium ion battery (NP-40) for
power. Never try to use any other type of battery.
To charge the battery
1. Positioning the positive
-
terminals of the battery with those of
+
and negative
the charger unit, load the battery into
the charger unit.
2. Plug the charger unit into a
household power outlet.
About 150 minutes are required to reach
full charge. The [CHARGE] lamp will go
out when charging is complete. Unplug the
power cord from the power outlet and then
remove the battery from the charger.
Lamp StatusDescription
Lit RedCharging
Flashing RedCharger unit or battery problem (page 147)
Off
Charging complete or standing by, due to abnormally
high or low ambient temperature (page 147)
[CHARGE] lamp
11
Quick Start Basics
Other Charging Precautions
• Use the special charger (BC-31L) to charge the special lithium ion battery (NP-40).
Never use any other type of charger device. Attempting to use a different charger
can result in unexpected accident.
• A battery that is still warm due to normal use may not charge fully. Give the battery
time to cool before charging it.
• A battery discharges slightly even when it is not loaded in the camera. Because of
this, it is recommended that you charge the battery immediately before you need to
use it.
• Charging the camera’s battery may cause interference with TV and radio reception.
If this happens, plug the charger into an outlet that is further away from the TV or
radio.
• Actual charging time depends on current battery capacity and charging conditions.
To load the battery
1. Open the battery cover.
Slide the battery cover slider towards OPEN and
then open it as indicated by the arrows in the
illustration.
2. Load the battery.
With the EXILIM logo on the battery facing
upwards (in the direction of the monitor
screen), hold the stopper next to the
battery in the direction indicated by the
arrow as you slide the battery into the
camera. Press the battery in until the
stopper secures it in place.
3. Close the battery cover.
Close the battery cover and then shift the slider
towards LOCK.
• For information about how to replace the battery,
see page 147.
1
2
Stopper
Battery
2
1
12
Quick Start Basics
Checking Remaining Battery Power
As battery power is consumed, a battery indicator on the monitor screen indicates
remaining power as shown below.
Remaining PowerHighLow
Battery Indicator***
Indicator ColorCyan* Amber*Red*Red
indicates battery power is low. Charge the battery as soon as possible.
Recording is not possible when is indicated. Charge the battery immediately.
• The level shown by the battery indicator may change when you switch between the
REC mode and PLAY mode.
• Leaving the camera for about two days with no power supplied while the battery is
dead will cause its date and time settings to be cleared. You will have to reconfigure the settings after power is restored.
• See page 168 for information about battery life and memory capacity.
Battery Power Conservation Tips
• When you do not need to use the flash, select ? (flash off) for the flash setting
(page 28).
• Enable the Auto Power Off and the Sleep features to protect against wasting
battery power when you forget to turn off the camera (pages 133, 133).
Configuring the Display Language the First Time You Turn On
the Camera
The first time you load a battery into the camera, a
[ON/OFF]
screen appears for configuring the display language,
date, and time settings. Failure to set the date and
time correctly will cause the wrong date and time
data to be recorded with images.
[BS]
=8?
=4?
=2?
=6?
[
SET
1. Press [ON/OFF] to turn on the camera.
2. Use [8], [2], [4], and [6] to select the language you want and then
press [SET].
3. Use [8], [2], [4], and [6] to select the area
where you will be using the camera and then
press [SET].
The selected area is highlighted in red.
13
Quick Start Basics
]
4. Use [8] and [2] to select the city where you will be using the camera
and then press [SET].
5. Use [8] and [2] to select the summer time (DST) setting you want and
then press [SET].
6. Use [8] and [2] to select a date style and then press [SET].
Example: 19. 12. 09
YY/MM/DD
DD/MM/YY
MM/DD/YY
* 09/12/19
* 19/12/09
* 12/19/09
7. Set the date and the time.
Use [4] and [6] to select the setting you want to change and then use [8] and
[2] to change it.
To switch between 12-hour and 24-hour format, press [BS].
8. Press [SET].
• If you make a mistake, you can change the settings later (pages 131, 132).
NOTE
• Each country controls its local time offset and the use of summer time, and so they
are subject to change.
14
Quick Start Basics
Preparing a Memory Card
Though the camera has built-in memory that can be used to store images and
movies, you probably will want to purchase a commercially available memory card for
greater capacity. The camera does not come with a memory card. Images recorded
while a memory card is loaded are saved to the memory card. When no memory card
is loaded, images are saved to built-in memory.
• For information about memory card capacities, see page 164.
Slide the battery cover slider towards OPEN and
then open it as indicated by the arrows in the
illustration.
2. Load a memory card.
Positioning the memory card so
its front is facing upwards
(towards the monitor screen
side of the camera), slide it into
the card slot all the way in until
you hear it click securely into
place.
FrontBack
3. Close the battery cover.
Close the battery cover and then shift the slider
towards LOCK.
• For information about how to replace the memory
card, see page 149.
1
2
Front
2
1
15
Quick Start Basics
IMPORTANT!
• Never insert anything besides a supported memory card (page 15) into the memory
card slot.
• Should water or any foreign object ever get into the card slot, immediately turn off
the camera, remove the battery, and contact your retailer or nearest CASIO
authorized service center.
To format (initialize) a new memory card
You need to format a new memory card before using it for the first time.
1. Turn on the camera and press [MENU].
2. Select the “Set Up” tab, select “Format” and then press [6].
3. Use [8] and [2] to select “Format” and then press [SET].
IMPORTANT!
• Formatting a memory card that already has snapshots or other files on it, will delete
its contents. Normally you do not need to format a memory card again. However, if
storing to a card has slowed down or if you notice any other abnormality, re-format
the card.
• Be sure to use the camera to format a memory card. Formatting a memory card on
a computer and then using it in the camera can slow down data processing by the
camera. In the case of an SD or SDHC memory card, formatting on a computer can
result in non-conformity with the SD format, causing problems with compatibility,
operation, etc.
16
Quick Start Basics
Turning the Camera On and Off
To turn power on
To enter the REC Mode, press [ON/OFF] (Power) or [r]
(REC). To enter the PLAY mode, press [p] (PLAY).
The back lamp will light (green) momentarily and the
camera will turn on. If you are entering the REC mode,
the lens will extend from the camera at this time.
• Take care to ensure that nothing is restricting or
coming into contact with the lens as it extends. Holding
the lens with your hand so it cannot extend creates the
risk of malfunction.
•Pressing [p] (PLAY) while in the REC mode switches
to the PLAY mode. The lens retracts about 10 seconds
after switching modes.
• The Sleep function or Auto Power Off (pages 133, 133)
will turn off power automatically if you do not perform
any operation for a preset amount of time.
[ON/OFF] (Power)
Back lamp
[p]
(PLAY)
[r]
(REC)
To turn off the camera
Press [ON/OFF] (Power).
• You can configure the camera so power does not turn on when you press [r]
(REC) or [p] (PLAY). You also can configure the camera to turn off when you
press [r] (REC) or [p] (PLAY) (page 134).
17
Quick Start Basics
To shoot a snapshot
1. Press [r] (REC) to turn on the camera.
Make sure R is on the display. If it isn’t, see page 52.
Snapshot mode icon
2. Point the camera
at the subject.
You can zoom the
image, if you want.
Zoom controller
3. Half-press the shutter button to
focus the image.
When focus is complete, the camera will
beep, the back lamp will light green, and
the focus frame will turn green.
Half-press
Press lightly
until the
button stops.
Beep, beep (Image is in focus.)
Monitor screen
Shutter button
[r] (REC)
w Wide Anglez Telephoto
Back lamp
Focus frame
When you half-press the shutter button, the
camera automatically adjusts exposure and
focuses on the subject it is currently pointed
at. Mastering how much pressure is required
for a half-press and a full-press of the shutter
button is an important technique for goodlooking images.
18
Quick Start Basics
4. Continuing to keep the camera still, press the shutter button the rest of
the way down.
This records the snapshot.
Full-press
Shooting a Movie
Press [0] to start movie
recording. Press [0] again to
stop movie recording. See
page 47 for details.
Snap (Image is recorded.)
IMPORTANT!
• While the “Anti Shake” setting is “D Auto” or “A Camera AS”, half pressing the
shutter will cause the camera to vibrate and emit an operation sound. This is
normal and does not indicate malfunction (page 68).
[0]
. Using Quick Shutter
Fully pressing the shutting button without waiting for Auto Focus to operate will record
using Quick Shutter (page 71).
• With Quick Shutter, the camera focuses faster than normal Auto Focus, which
means you can capture quick moving action more easily. Note, however, that some
images may be out of focus when Quick Shutter is used.
• Whenever possible, take a little extra time to half-press the shutter button in order
to ensure proper focus.
. If the image does not focus...
If the focus frame stays red and the back lamp is flashing green, it means that the
image is not in focus (because the subject is too close, etc.) Re-point the camera at
the subject and try to focus again.
. If the subject is not in the center of the frame...
“Focus lock” (page 65) is the name of a technique you can use when you want to
shoot an image in which the subject to be focused on is not within the focus frame in
the center of the screen.
19
Quick Start Basics
Holding the Camera Correctly
Your images will not come out clearly if you move the camera when you press the
shutter button. When pressing the shutter button, be sure to hold the camera as
shown in the illustration below, and keep it still by pressing your arms firmly against
your sides as you shoot.
Holding the camera still, carefully press the shutter button and take care to avoid all
movement as the shutter releases and for a few moments after it releases. This is
especially important when available lighting is low, which slows down the shutter
speed.
HorizontalVertical
Hold the camera so the flash is
above the lens.
NOTE
• Take care that your fingers and the
strap do not cover any of the areas
indicated in the illustration.
• To protect against accidentally
dropping the camera, attach the wrist
strap and make sure it is around your
fingers or wrist while you are operating
the camera.
• Never swing the camera around by its
strap.
• The supplied strap is intended for use
with this camera only. Never use it for
any other purpose.
Flash
Lens
Front lamp
Microphone
Strap
20
Quick Start Basics
Viewing Snapshots
Use the following procedure to view snapshots on the camera’s monitor screen.
• For information about how to play back movies, see page 80.
1. Press [p] (PLAY) to enter the PLAY
mode.
• This will display one of the snapshots
currently stored in memory.
• Information about the displayed
snapshot also is included (page 154).
• You also can clear the information to
view only the snapshot (page 137).
• You can zoom in on the image by
sliding the zoom controller towards z (page 81). If you are recording a
snapshot that is very important to you, it is recommended that you zoom the
image and check its details after recording it.
[p] (PLAY)
2. Use [4] and [6] to scroll between images.
• Holding down either button scrolls at high speed.
[6]
[6]
[4]
21
[4]
Quick Start Basics
Deleting Images
If memory becomes full, you can delete images you no longer need to free up storage
and record more images.
• Remember that a file (image) delete operation cannot be undone.
• Deleting an audio snapshot (page 100) deletes both the snapshot and the audio
file.
To delete a single file
1. Press [p] (PLAY) to enter the PLAY mode and then
press [2] ().
2. Use [4] and [6] to scroll through the files until the one
you want to delete is displayed.
3. Use [8] and [2] to select “Delete” and then press [SET].
• To delete other files, repeat steps 2 and 3.
• To exit the delete operation, press [MENU].
To delete all files
1. Press [p] (PLAY) to enter the PLAY mode and then press [2] ().
2. Use [8] and [2] to select “All Files Delete” and then press [SET].
3. Use [8] and [2] to select “Yes” and then press [SET] to delete all files.
This will cause the message “There are no files” to appear.
22
Quick Start Basics
Snapshot Shooting Precautions
Operation
• Never open the battery cover while the back lamp is flashing green. Doing so can
result in the image you just shot being saved incorrectly, damage to other images
stored in memory, malfunction of the camera, etc.
• If unwanted light is shining directly onto the lens, shade the lens with your hand
when shooting an image.
Monitor Screen when Shooting Snapshots
• Subject brightness conditions can cause monitor screen response to slow and can
cause digital noise in the monitor screen image.
• The image that appears on the monitor screen is for image composition. The actual
image will be recorded at the quality set for the image quality setting (page 74).
Shooting Indoors under Fluorescent Lighting
• Minute flickering of fluorescent lighting can affect the brightness or color of an
image.
Auto Focus Restrictions
• Any of the following can make proper focus impossible.
– Solid color wall or other very low contrast subject
– Strongly back lit subject
– Very shiny subject
– Blinds or other subject with a repeating horizontal pattern
– Multiple subjects at varying distances from the camera
– Subject in a dark location
– Subject that is too far away for light from the AF assist lamp to reach
– Camera movement while shooting
– Fast-moving subject
– Subjects outside the focus range of the camera
• If you cannot focus properly, try using focus lock (page 65) or Manual Focus (page
63).
23
Quick Start Basics
Snapshot Tutorial
Using the Control Panel
The Control Panel can be used to configure camera settings.
1. In the REC mode, press [SET].
This will select one of the Control Panel icons and display its settings.
[8] [2] [4] [6]
[SET]
Available settings
2. Use [8] and [2] to select the setting you want to change.
Image size/Quality* (pages 25, 74)
1
Flash (page 28)
2
Auto Shutter (page 30)
3
Auto Shutter trigger sensitivity
4
(page 32)
ISO sensitivity (page 41)
5
Continuous shutter (page 39)
6
* Image quality cannot be changed using the Control Panel.
3. Use [4] and [6] to change the setting.
Control Panel
1
2
3
4
5
6
7
8
9
Face recognition/Make-up
7
(pages 34, 46)
EV shift (page 42)
8
Date/Time (page 43)
9
4. If you want to configure another setting, repeat steps 2 and 3.
5. After all of the settings are the way you want, press [SET].
This will apply the settings and return to the REC mode.
NOTE
• You can configure the camera to turn off display of the Control Panel when you
press [SET] (page 126).
• You also can configure settings other than those listed above (page 61).
• The Control Panel cannot be displayed while a Prerecord Movie, For YouTube, or
Voice Recording Operation is in progress.
24
Snapshot Tutorial
Changing the Image Size (Size)
. Pixels
A digital camera image is a collection of small
dots called “pixels”. The more pixels there are
in an image, the more detail there will be.
However, you generally can do with fewer
pixels when printing an image (L size) through
a print service, attaching an image to e-mail,
when viewing the image on a computer, etc.
. About image sizes
The size of an image indicates how many pixels it contains, and is expressed as
horizontal pixels
x
vertical pixels.
Pixel
7M (3072x2304) size image =
Approximately 7 million pixels
VGA (640x480) size image =
Approximately 300,000 pixels
3072*
2304*
640*
480*
* Unit: pixels
25
Snapshot Tutorial
Image Size Selection Tips
Note that larger images have more pixels, so they take up more memory space.
Large Number
of Pixels
Small Number
of Pixels
More detail, but takes up more memory. Best
when you plan to print large-size prints (such
as A3 size).
Less detail, but takes up less memory. Best
when you want to send images by e-mail,
etc.
• For information about image size, image quality, and number of images that can be
stored, see page 164.
• For information about movie image size, see page 75.
• For information about resizing existing snapshots, see page 98.
26
Snapshot Tutorial
. To select the image size
1. In the REC mode, press [SET].
2. Use [8] and [2] to select the top Control Panel option (Image Size).
3. Use [4] and [6] to select an image size and then press [SET].
Image Size
(Pixels)
10M
x
(3648
2736)
3:2
x
2432)
(3648
16:9
x
2048)
(3648
7M
x
2304)
(3072
4M
x
1728)
(2304
2M
x
1200)
(1600
VGA
x
480)
(640
Suggested
Print Size and
Application
Poster Print
Poster Print
HDTV
A3 Print
A4 Print
x
3.5"
5" Print
E Mail
Description
Good detail for better clarity even for images
cropped (page 98) from the original
Good detail
Best when preserving memory capacity is
relatively more important than image quality.
Image files are smaller, which is better when
attaching images to e-mail. However, images
are relatively coarser.
• The initial factory default image size setting is 10M (10 million pixels).
x
• Selecting 3:2 (3648
2432 pixels) records images with an aspect ratio of 3:2, which
matches the standard aspect ratio of print paper.
• The letters “HDTV” stand for “High Definition Television”. An HDTV screen has an
aspect ratio of 16:9, which makes them wider than the usual 4:3 aspect ratio of
television screens of the past. Your camera can record images that are compatible
with the aspect ratio an HDTV screen.
• You should regard the print paper sizes suggested here as guidelines only (200 dpi
print resolution).
27
Snapshot Tutorial
Using Flash (Flash)
>?<
N
1. In the REC mode, press [2] () once.
2. Use [4] and [6] to select the flash
setting you want and then press [SET].
When the “R Panel” menu item (page 126)
is “Hide” (so the Control Panel is not
[2] ()
displayed), pressing [2] () will cycle
through the available flash settings.
Auto Flash
Flash fires automatically in accordance with exposure
(amount of light and brightness) conditions.
Flash OffFlash does not fire.
Flash always fires. This setting can be used to brighten a
Flash On
subject that normally comes out dark due to daylight or
backlight (daylight synchro flash).
Soft FlashSoft flash always fires, regardless of exposure conditions
Red Eye
Reduction
Flash fires automatically. This type of flash can be used to
reduce the chance of redness in the subject’s eyes.
3. Press the shutter button to shoot.
Back lamp
2
< indicates the flash will fire.
Flashes orange while the flash is charging to indicate
that image recording is disabled.
• You will not be able to take another flash snapshot
until the lamp stops flashing orange, which
indicates that charging is complete.
Flash
NOTE
• Take care so your fingers and the strap do not block the flash.
• The desired effect may not be obtained when the subject is too far away or too
close.
• Flash charging time depends on operating conditions (battery condition, ambient
temperature, etc.) With a fully charged battery it takes about 4 seconds.
• Shooting with flash turned off when lighting is dim results in a slow shutter speed,
which can cause image blur due to camera movement. Under such conditions,
secure the camera with a tripod, etc.
• With red eye reduction, the flash is fired automatically in accordance with
exposure. It does not fire in areas where lighting is bright.
• The presence of outdoor sunlight, fluorescent lighting, or some other light source
can cause abnormal image colors.
• Select “Flash Off” for the flash setting when shooting in areas where flash
photograph is prohibited.
28
Snapshot Tutorial
• Approximate Flash Range (ISO Sensitivity: Auto)
Wide Angle: 0.2 m to 4.5 m (0.7' to 14.8')
Telephoto: 0.5 m to 2.0 m (1.6' to 6.6')
* The above values depend on the optical zoom setting.
Red-eye Reduction
Using the flash to shoot at night or in a dimly lit room can cause red spots inside the
eyes of people who are in the image. This is caused when the light from the flash
reflects off of the retina of the eye. When red-eye reduction is selected as the flash
mode, the camera fires a pre-flash to cause the irises in the eyes of any people in the
image to close, which reduces the chance of red eye.
Note the following important points when using red-eye reduction.
• Red-eye reduction does not work unless the people in the image are looking
directly at the camera (flash).
• Red-eye reduction may not work very well if the subjects are located far away from
the camera.
Other Useful Flash Features
• Changing the flash intensity (page 79)
29
Snapshot Tutorial
Using Auto Shutter (Auto Shutter)
With Auto Shutter, the camera releases the shutter automatically when it detects that
certain conditions are present.
Detect Blur
Detect Panning
Detect Smile
Camera releases the shutter automatically when it detects
image blur to camera and subject movement are
minimized.
When panning, the camera releases the shutter
automatically when it determines there is no blur in the
subject being followed.
Camera releases the shutter automatically when it detects
the subject is smiling.
1. In the REC mode, press [SET].
2. Use [8] and [2] to select the third Control Panel option from the top
(Auto Shutter).
3. Use [4] and [6] to select the Auto Shutter type and then press [SET].
To use Detect Blur to minimize image blur (Detect Blur)
1. Point the camera at the subject and half-press the shutter button. Wait
until the camera adjusts exposure and focus automatically.
2. Press the shutter button the rest of the way
down.
The camera will go into a standby mode and start
detecting hand and subject movement. The camera
will release the shutter automatically the moment it
determines there is no image blur.
•“0 Auto” flashes on the monitor screen while
detection of image blur due to hand movement or
subject movement is in progress.
Indicator:
The indicator color changes
from red to green when the
camera is getting ready to
release the shutter.
30
Snapshot Tutorial
Loading...
+ 140 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.