Casio EX-Z19 User Manual

User’s Guide
E
K1191PCM1DMX
Thank you for purchasing this CASIO product.
• Before using it, be sure to read the precautions contained in this User’s Guide.
• Keep the User’s Guide in a safe place for future reference.
• For the most up-to-date information about this product, visit the official EXILIM Website at http://www.exilim.com/
1

Unpacking

As you unpack your camera, check to make sure that all items shown below are included. If anything is missing, contact your original retailer.
Digital camera
Power cord Strap
USB cable AV cable CD-ROM Basic Reference
Rechargeable lithium ion
battery (NP-60)
To attach the strap to the camera
Charger unit (BC-60L)
Attach strap here.
2

Read this first!

• The contents of this manual are subject to change without notice.
• The contents of this manual have been checked at each step of the production process. Feel free to contact us if you notice anything that is questionable, erroneous, etc.
• Any copying of the contents of this User’s Guide, either in part or its entirety, is forbidden. Except for your own personal use, any other use of the contents of this manual without the permission of CASIO COMPUTER CO., LTD. is forbidden under copyright laws.
• CASIO COMPUTER CO., LTD. shall not be held liable for any damages or lost profits suffered by you or any third party due to the use or malfunction of this product.
• CASIO COMPUTER CO., LTD. shall not be held liable for any damages, lost profits, or claims by third parties arising out of the use of Photo Loader with HOT ALBUM, Photo Transport, or YouTube Uploader for CASIO.
• CASIO COMPUTER CO., LTD. shall not be held liable for any damages or lost profits caused by loss of memory contents due to malfunction, repair, or any other reason.
• Note that the example screens and product illustrations shown in this User’s Guide may differ somewhat from the screens and configuration of the actual camera.
LCD Panel
The liquid crystal panel of the monitor screen uses high-precision technology that provides a pixel yield in excess of 99.99%. This means that some very small number of pixels may not light or may remain lit at all times. This is due to the characteristics of the liquid crystal panel, and does not indicate malfunction.
Take a few test shots
Before shooting your final image, shoot a test shot to ensure that the camera is recording correctly.
3

Contents

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Read this first! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
❚❙
Quick Start Basics 8
What is a digital camera? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
What you can do with your CASIO camera . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
First, charge the battery prior to use.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
To charge the battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
To load the battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Configuring the Display Language the First Time You Turn On the Camera. . 13
Preparing a Memory Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Supported Memory Cards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
To load a memory card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
To format (initialize) a new memory card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
To shoot a snapshot. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Holding the Camera Correctly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Viewing Snapshots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Deleting Images. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
To delete a single file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
To delete all files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Snapshot Shooting Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Auto Focus Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Turning the Camera On and Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
To turn power on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
To turn off the camera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
❚❙
Snapshot Tutorial 23
Using the Control Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Changing the Image Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Size) . . 24
Using Flash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(Flash) . . 26
Using Face Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . (Face Detection) . . 28
Reducing the Effects of Camera and Subject Movement . . . (Anti Shake) . . 30
Specifying ISO Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (ISO) . . 31
Adjusting White Balance . . . . . . . . . . . . . . . . . . . . . . . . . (White Balance) . . 31
Correcting Image Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . .(EV Shift) . . 33
Using the easy Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Changing the Control Panel Date/Time Style . . . . . . . . . . . . . . . . . . . . . . . . 36
Shooting with Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Optical Zoom and Digital Zoom Switch Point . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
❚❙
Recording Movie Images and Audio 39
To record a movie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Recording Audio Only . . . . . . . . . . . . . . . . . . . . . . . . . . (Voice Recording) . . 40
To play back an audio recording. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
4
Contents
❚❙
Using BEST SHOT 42
What is BEST SHOT? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Some Sample Scenes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
To shoot an image with BEST SHOT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
❚❙
Advanced Settings 46
Using On-screen Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
REC Mode Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (REC) . . 48
Selecting a Focus Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(Focus) . . . 48
Using Continuous Shutter . . . . . . . . . . . . . . . . . . . . . . . . . . . .(Continuous). . . 51
Using the Self-timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Self-timer) . . . 52
Shooting with Face Detection . . . . . . . . . . . . . . . . . . . . . .(Face Detection). . . 53
Reducing the Effects of Camera and Subject Movement . . . . (Anti Shake). . . 53
Specifying the Auto Focus Area . . . . . . . . . . . . . . . . . . . . . . . . . . (AF Area). . . 53
Using the easy Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (easy Mode). . . 54
Assigning Functions to the [4] and [6] Keys . . . . . . . . . . . . . . . (L/R Key). . . 54
Displaying the On-screen Grid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Grid). . . 54
Turning Digital Zoom On or Off . . . . . . . . . . . . . . . . . . . . . . .(Digital Zoom). . . 55
Turning on Image Review . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(Review) . . . 55
Using Icon Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Icon Help). . . 55
Configuring Power On Default Settings . . . . . . . . . . . . . . . . . . . . (Memory). . . 56
Image Quality Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Quality) . . 57
Specifying Snapshot Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Size) . . . 57
Specifying Snapshot Image Quality . . . . . . . . . . . . . . . (Quality (Snapshot)). . . 57
Specifying Movie Image Quality . . . . . . . . . . . . . . . . . . . . .(Quality (Movie)). . . 58
Correcting Image Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . (EV Shift). . . 58
Controlling White Balance . . . . . . . . . . . . . . . . . . . . . . . . . (White Balance) . . . 58
Specifying ISO Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(ISO). . . 58
Specifying the Metering Mode . . . . . . . . . . . . . . . . . . . . . . . . . . .(Metering) . . . 59
Using Built-in Color Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Color Filter). . . 59
Controlling Image Sharpness . . . . . . . . . . . . . . . . . . . . . . . . . . (Sharpness) . . . 59
Controlling Color Saturation . . . . . . . . . . . . . . . . . . . . . . . . . . . (Saturation). . . 60
Adjusting Image Contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(Contrast). . . 60
Specifying Flash Intensity . . . . . . . . . . . . . . . . . . . . . . . . . (Flash Intensity) . . . 60
❚❙
Viewing Snapshots and Movies 61
Viewing Snapshots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Viewing a Movie. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Zooming an On-screen Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Displaying 12 Images on the Same Screen. . . . . . . . . . . . . . . . . . . . . . . . . . 62
Viewing Snapshots and Movies on a TV Screen. . . . . . . . . . . . . . . . . . . . . . 63
❚❙
Other Playback Functions (PLAY) 65
Playing a Slideshow on the Camera . . . . . . . . . . . . . . . . . . . . (Slideshow) . . 65
Selecting Images for Printing . . . . . . . . . . . . . . . . . . . . . (DPOF Printing) . . 66
Protecting a File Against Deletion . . . . . . . . . . . . . . . . . . . . . . . . (Protect) . . 66
5
Contents
Rotating an Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Rotation) . . 67
Resizing a Snapshot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(Resize) . . 67
Cropping a Snapshot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Trimming) . . 68
Adding Audio to a Snapshot . . . . . . . . . . . . . . . . . . . . . . . . . . . (Dubbing) . . 68
To play snapshot audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Copying Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Copy) . . 70
❚❙
Printing 71
Printing Snapshots. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Connecting Directly to a PictBridge Compatible Printer . . . . . . . . . . . . . . . . 72
Using DPOF to Specify Images to be Printed and the Number of Copies. . . 74
❚❙
Using the Camera with a Computer 77
Things you can do using a computer... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Using the Camera with a Windows Computer . . . . . . . . . . . . . . . . . . . . . . . . 78
Viewing and Storing Images on a Computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Save images to a computer automatically/Manage images . . . . . . . . . . . . . . . . 83
Playing Movies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Uploading Movie Files to YouTube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Transferring Images from Your Computer to Camera Memory. . . . . . . . . . . . . . 86
Viewing User Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . (PDF Files) . . . 88
User Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Using the Camera with a Macintosh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Connecting the Camera to Your Computer and Saving Files . . . . . . . . . . . . . . . 89
Transferring Images Automatically and Managing Them on Your Macintosh. . . 91
Playing a Movie. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Viewing User Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . .(PDF Files) . . . 92
User Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Files and Folders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Memory Card Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
❚❙
Other Settings (Set Up) 96
Selecting a REC Mode Screen Layout . . . . . . . . . . . . . . . . . . (R Panel) . . 96
Selecting a PLAY Mode Screen Layout . . . . . . . . . . . . . . . . (P Display) . . 97
Configuring Camera Sound Settings . . . . . . . . . . . . . . . . . . . . . (Sounds) . . 97
Specifying the File Name Serial Number Generation Rule . . . . . (File No.) . . 98
Configuring World Time Settings . . . . . . . . . . . . . . . . . . . . . (World Time) . . 99
Time Stamping Snapshots . . . . . . . . . . . . . . . . . . . . . . . . . . (Timestamp) . . 99
Setting the Camera’s Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Adjust) . 100
Specifying the Date Style . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Date Style) . 100
Specifying the Display Language . . . . . . . . . . . . . . . . . . . . . . (Language) . 101
Configuring Sleep State Settings . . . . . . . . . . . . . . . . . . . . . . . . . (Sleep) . 101
Configuring Auto Power Settings . . . . . . . . . . . . . . . . . . (Auto Power Off) . 102
Configuring [r] and [p] Settings . . . . . . . . . . . . . . . . . . . (REC/PLAY) . 102
Configuring USB Protocol Settings . . . . . . . . . . . . . . . . . . . . . . . . . (USB) . 103
6
Contents
Selecting the Screen Aspect Ratio and Video Output System (Video Out) . 103
Formatting Built-in Memory or a Memory Card . . . . . . . . . . . . . . (Format) . 104
Resetting the Camera to Factory Defaults . . . . . . . . . . . . . . . . . . (Reset) . 104
❚❙
Configuring Monitor Screen Settings 105
Using the On-screen Histogram to Check Exposure . . . . . . (+Histogram) . 105
How to Use the Histogram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
❚❙
Appendix 107
Precautions during Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Power Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
To replace the battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Battery Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Using the Camera in another Country . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Using a Memory Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
To replace the memory card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Computer System Requirements for Bundled Software . . . . . . . . . . . . . . . 120
General Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Monitor Screen Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
Reset Initial Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
When things don’t go right... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Display Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Number of Snapshots and Movie Recording Time . . . . . . . . . . . . . . . . . . . 133
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
7
Contents

Quick Start Basics

What is a digital camera?

A digital camera stores images on a memory card, so you can record and delete images a countless number of times.
Record
Delete
You can use the images you record in a variety of different ways.
Store images on your
computer.
Print images. Attach images to e-mail.
8
Play
Quick Start Basics

What you can do with your CASIO camera

Your CASIO camera is packed with a powerful selection of features and functions to make recording of digital images easier, including the following three main functions.
Face Detection
Point the camera at a person and it automatically detects the person’s face for beautiful portraits every time.
See page
28 for more information.
Anti Shake
The camera corrects automatically to minimize image blur due to camera movement and high­speed subject movement.
See page
30 for more information.
BEST SHOT
Simply select the sample scene you want and the camera sets up automatically. Then all you need do is press the shutter button for perfect images.
See page
42 for more information.
9
Quick Start Basics

First, charge the battery prior to use.

Note that the battery of a newly purchased camera is not charged. Perform the steps under “To charge the battery” to bring the battery to a full charge.
• Your camera requires a special CASIO rechargeable lithium ion battery (NP-60) for power. Never try to use any other type of battery.

To charge the battery

1. Positioning the positive
-
terminals of the battery with those of
+
and negative
the charger unit, load the battery into the charger unit.
2. Plug the charger unit into a household
power outlet.
About 90 minutes are required to reach full charge. The [CHARGE] lamp will go out when charging is complete. Unplug the power cord from the power outlet and then remove the battery from the charger.
Lamp Status Description
Lit Red Charging
Flashing Red Charger unit or battery problem (page 116)
Off
Charging complete or standing by, due to abnormally high or low ambient temperature (page 116)
[CHARGE] lamp
10
Quick Start Basics
Other Charging Precautions
• Use the special charger (BC-60L) to charge the special lithium ion battery (NP-60). Never use any other type of charger device. Attempting to use a different charger can result in unexpected accident.
• A battery that is still warm due to normal use may not charge fully. Give the battery time to cool before charging it.
• A battery discharges slightly even when it is not loaded in the camera. Because of this, it is recommended that you charge the battery immediately before you need to use it.
• Charging the camera’s battery may cause interference with TV and radio reception. If this happens, plug the charger into an outlet that is further away from the TV or radio.
• Actual charging time depends on current battery capacity and charging conditions.

To load the battery

1. Open the battery cover.
Pressing the battery cover, slide it in the direction indicated by the arrow.
2. Load the battery.
With the EXILIM logo on the battery facing downwards (in the direction of the lens), hold the stopper next to the battery in the direction indicated by the arrow as you slide the battery into the camera. Press the battery in until the stopper secures it in place.
Stopper
Battery
1
2
3. Close the battery cover.
Pressing the battery cover against the camera, slide it closed.
• For information about how to replace the battery, see page 116.
2
1
11
Quick Start Basics
Checking Remaining Battery Power
As battery power is consumed, a battery indicator on the monitor screen indicates remaining power as shown below.
Remaining Power High Low
Battery Indicator ***
Indicator Color Cyan * Amber * Red * Red
indicates battery power is low. Charge the battery as soon as possible.
Recording is not possible when is indicated. Charge the battery immediately.
• The level shown by the battery indicator may change when you switch between the REC mode and PLAY mode.
• Leaving the camera for about two days with no power supplied while the battery is dead will cause its date and time settings to be cleared. You will have to re­configure the settings after power is restored.
• See page 137 for information about battery life and memory capacity.
Battery Power Conservation Tips
• When you do not need to use the flash, select ? (flash off) for the flash setting (page 26).
• Enable the Auto Power Off and the Sleep features to protect against wasting battery power when you forget to turn off the camera (pages 101, 102).
12
Quick Start Basics

Configuring the Display Language the First Time You Turn On the Camera

The first time you load a battery into the camera, a screen appears for configuring the display language, date, and time settings. Failure to set the date and time correctly will cause the wrong date and time data to be recorded with images.
1. Press [ON/OFF] to turn on the camera.
[BS]
[ON/OFF]
=8? =4? =2?
[
SET
=6?
2. Use [8], [2], [4], and [6] to select the language you want and then
press [SET].
3. Use [8], [2], [4], and [6] to select the area
where you will be using the camera and then press [SET].
The selected area is highlighted in red.
4. Use [8] and [2] to select the city where you
will be using the camera and then press [SET].
5. Use [8] and [2] to select the summer time (DST) setting you want and
then press [SET].
6. Use [8] and [2] to select a date style and then press [SET].
Example: 19. 12. 09 YY/MM/DD DD/MM/YY MM/DD/YY
* 09/12/19 * 19/12/09 * 12/19/09
]
7. Set the date and the time.
Use [4] and [6] to select the setting you want to change and then use [8] and [2] to change it. To switch between 12-hour and 24-hour format, press [BS].
8. Press [SET].
• If you make a mistake, you can change the settings later (pages 100, 101).
NOTE
• Each country controls its local time offset and the use of summer time, and so they are subject to change.
13
Quick Start Basics

Preparing a Memory Card

Though the camera has built-in memory that can be used to store images and movies, you probably will want to purchase a commercially available memory card for greater capacity. The camera does not come with a memory card. Images recorded while a memory card is loaded are saved to the memory card. When no memory card is loaded, images are saved to built-in memory.
• For information about memory card capacities, see page 133.

Supported Memory Cards

– SD Memory Card – SDHC Memory Card – MMC (MultiMediaCard) – MMCplus (MultiMediaCardplus)
Use one of the above types of memory card.

To load a memory card

1. Press [ON/OFF] to turn off the camera and then
open the battery cover.
Pressing the battery cover, slide it in the direction indicated by the arrow.
1
2
2. Load a memory
card.
Positioning the memory card so its front is facing downwards (in the direction of the lens), slide it into the card slot all the way in until you hear it click securely into place.
Front Back
Back
3. Close the battery cover.
Pressing the battery cover against the camera, slide it closed.
• For information about how to replace the memory card, see page 118.
14
2
1
Quick Start Basics
IMPORTANT!
• Never insert anything besides a supported memory card (page 14) into the memory card slot.
• Should water or any foreign object ever get into the card slot, immediately turn off the camera, remove the battery, and contact your retailer or nearest CASIO authorized service center.

To format (initialize) a new memory card

You need to format a new memory card before using it for the first time.
1. Turn on the camera and press [MENU].
2. Select the “Set Up” tab, select “Format” and then press [6].
3. Use [8] and [2] to select “Format” and then press [SET].
IMPORTANT!
• Formatting a memory card that already has snapshots or other files on it, will delete its contents. Normally you do not need to format a memory card again. However, if storing to a card has slowed down or if you notice any other abnormality, re-format the card.
• Be sure to use the camera to format a memory card. Formatting a memory card on a computer and then using it in the camera can slow down data processing by the camera. In the case of an SD or SDHC memory card, formatting on a computer can result in non-conformity with the SD format, causing problems with compatibility, operation, etc.
15
Quick Start Basics

To shoot a snapshot

1. Press [r] (REC) to turn on the camera.
Make sure t is on the display. If it isn’t, see page 42.
Snapshot mode icon
2. Point the camera at
the subject.
You can zoom the image, if you want.
Zoom button
3. Half-press the shutter button
to focus the image.
When focus is complete, the camera will beep, the back lamp will light green, and the focus frame will turn green.
Half-press
Press lightly until the button stops.
Beep, beep (Image is in focus.)
Monitor screen
Shutter button
[r] (REC)
z Telephoto w Wide Angle
Focus frameBack lamp
When you half-press the shutter button, the camera automatically adjusts exposure and focuses on the subject it is currently pointed at. Mastering how much pressure is required for a half-press and a full-press of the shutter button is an important technique for good­looking images.
16
Quick Start Basics
4. Continuing to keep the camera still, press the shutter button the rest of
the way down.
This records the snapshot.
Full-press
Snap (Image is recorded.)
. If the image does not focus...
If the focus frame stays red and the back lamp is flashing green, it means that the image is not in focus (because the subject is too close, etc.) Re-point the camera at the subject and try to focus again.
. If the subject is not in the center of the frame...
“Focus lock” (page 50) is the name of a technique you can use when you want to shoot an image in which the subject to be focused on is not within the focus frame in the center of the screen.
17
Quick Start Basics

Holding the Camera Correctly

Your images will not come out clearly if you move the camera when you press the shutter button. When pressing the shutter button, be sure to hold the camera as shown in the illustration below, and keep it still by pressing your arms firmly against your sides as you shoot. Holding the camera still, carefully press the shutter button and take care to avoid all movement as the shutter releases and for a few moments after it releases. This is especially important when available lighting is low, which slows down the shutter speed.
Horizontal Vertical
Hold the camera so the flash is above the lens.
NOTE
• Take care that your fingers and the strap do not cover any of the areas indicated in the illustration.
• To protect against accidentally dropping the camera, attach the wrist strap and make sure it is around your fingers or wrist while you are operating the camera.
• Never swing the camera around by its strap.
• The supplied strap is intended for use with this camera only. Never use it for any other purpose.
Flash
Front lamp Lens
Microphone
Strap
18
Quick Start Basics

Viewing Snapshots

Use the following procedure to view snapshots on the camera’s monitor screen.
• For information about how to play back movies, see page 61.
1. Press [p] (PLAY) to enter the
PLAY mode.
• This will display one of the snapshots currently stored in memory.
• Information about the displayed snapshot also is included (page
123).
• You also can clear the information to view only the snapshot (page 105).
• You can zoom in on the image by pressing the z side of the zoom button (page 62). If you are recording a snapshot that is very important to you, it is recommended that you zoom the image and check its details after recording it.
[p] (PLAY)
2. Use [4] and [6] to scroll between images.
• Holding down either button scrolls at high speed.
[6]
[6]
[4]
19
[4]
Quick Start Basics

Deleting Images

If memory becomes full, you can delete images you no longer need to free up storage and record more images.
• Remember that a file (image) delete operation cannot be undone.
• Deleting an audio snapshot (page 68) deletes both the snapshot and the audio file.

To delete a single file

1. Press [p] (PLAY) to enter the PLAY mode
and then press [2] ( ).
2. Use [4] and [6] to scroll through the files
until the one you want to delete is displayed.
3. Use [8] and [2] to select “Delete” and then
press [SET].
• To delete other files, repeat steps 2 and 3.
• To exit the delete operation, press [MENU].

To delete all files

1. Press [p] (PLAY) to enter the PLAY mode and then press [2] ( ).
2. Use [8] and [2] to select “All Files Delete” and then press [SET].
3. Use [8] and [2] to select “Yes” and then press [SET] to delete all files.
This will cause the message “There are no files” to appear.
20
Quick Start Basics

Snapshot Shooting Precautions

Operation
• Never open the battery cover while the back lamp is flashing green. Doing so can result in the image you just shot being saved incorrectly, damage to other images stored in memory, malfunction of the camera, etc.
• If unwanted light is shining directly onto the lens, shade the lens with your hand when shooting an image.
Monitor Screen when Shooting Snapshots
• Subject brightness conditions can cause monitor screen response to slow and can cause digital noise in the monitor screen image.
• The image that appears on the monitor screen is for image composition. The actual image will be recorded at the quality set for the image quality setting (page 57).
Shooting Indoors under Fluorescent Lighting
• Minute flickering of fluorescent lighting can affect the brightness or color of an image.

Auto Focus Restrictions

• Any of the following can make proper focus impossible. – Solid color wall or other very low contrast subject – Strongly back lit subject – Very shiny subject – Blinds or other subject with a repeating horizontal pattern – Multiple subjects at varying distances from the camera – Subject in a dark location – Camera movement while shooting – Fast-moving subject – Subjects outside the focus range of the camera
• If you cannot focus properly, try using focus lock (page 50) or Manual Focus (page
48).
21
Quick Start Basics

Turning the Camera On and Off

To turn power on

To enter the REC Mode, press [ON/OFF] (Power) or [r] (REC). To enter the PLAY mode, press [p] (PLAY). The back lamp will light (green) momentarily and the camera will turn on. If you are entering the REC mode, the lens will extend from the camera at this time.
• Take care to ensure that nothing is restricting or coming into contact with the lens as it extends. Holding the lens with your hand so it cannot extend creates the risk of malfunction.
•Pressing [p] (PLAY) while in the REC mode switches to the PLAY mode. The lens retracts about 10 seconds after switching modes.
• The Sleep function or Auto Power Off (pages 101, 102) will turn off power automatically if you do not perform any operation for a preset amount of time.
[ON/OFF] (Power)
Back lamp
[p]
(PLAY)
(REC)

To turn off the camera

Press [ON/OFF] (Power).
• You can configure the camera so power does not turn on when you press [r] (REC) or [p] (PLAY). You also can configure the camera to turn off when you press [r] (REC) or [p] (PLAY) (page 102).
[r]
22
Quick Start Basics

Snapshot Tutorial

Using the Control Panel

The Control Panel can be used to configure camera settings.
1. In the REC mode, press [SET].
This will select one of the Control Panel icons and display its settings.
[8] [2] [4] [6]
[SET]
Available settings
2. Use [8] and [2] to select the setting you want to change.
Image size/Quality* (pages 24, 57)
1
Flash mode (page 26)
2
Face detection (page 28)
3
Anti shake (page 30)
4
ISO sensitivity (page 31)
5
* Image quality cannot be changed using the Control Panel.
3. Use [4] and [6] to change the setting.
Control Panel
1 2 3 4 5 6 7 8 9
White balance (page 31)
6
EV shift (page 33)
7
easy Mode (page 34)
8
Date/Time (page 36)
9
4. If you want to configure another setting, repeat steps 2 and 3.
5. After all of the settings are the way you want, press [SET].
This will apply the settings and return to the REC mode.
NOTE
• You can configure the camera to turn off display of the Control Panel when you press [SET] (page 96).
• You also can configure settings other than those listed above (page 46).
• The Control Panel cannot be displayed while a For YouTube, or Voice Recording Operation is in progress.
23
Snapshot Tutorial

Changing the Image Size (Size)

. Pixels
A digital camera image is a collection of small dots called “pixels”. The more pixels there are in an image, the more detail there will be. However, you generally can do with fewer pixels when printing an image (L size) through a print service, attaching an image to e-mail, when viewing the image on a computer, etc.
. About image sizes
The size of an image indicates how many pixels it contains, and is expressed as
x
horizontal pixels
7M (3072x2304) size image =
1
Approximately 7 million pixels VGA (640x480) size image =
2
Approximately 300,000 pixels
vertical pixels.
640
480
2
Image Size Selection Tips
Note that larger images have more pixels, so they take up more memory space.
Large Number of Pixels
* More detail, but takes up more memory. Best when you plan
to print large-size prints (such as A3 size).
Small Number of Pixels
* Less detail, but takes up less memory. Best when you want to
send images by e-mail, etc.
Pixel
3072
Unit: pixels
1
2304
• For information about image size, image quality, and number of images that can be stored, see page 133.
• For information about movie image size, see page 58.
• For information about resizing existing snapshots, see page 67.
24
Snapshot Tutorial
. To select the image size
1. In the REC mode, press [SET].
2. Use [8] and [2] to select the top Control Panel option (Image Size).
3. Use [4] and [6] to select an image size and then press [SET].
Image Size (Pixels)
9M
x
(3456
2592)
3:2
x
2304)
(3456
16:9
x
1944)
(3456
7M
x
2304)
(3072
4M
x
1728)
(2304
2M
x
1200)
(1600
VGA
x
480)
(640
Suggested Print Size and Application
A3 Print
A3 Print
HDTV
A3 Print
A4 Print
x
3.5"
5" Print
E Mail
Description
Good detail for better clarity even for images cropped (page 68) from the original
Good detail
Best when preserving memory capacity is relatively more important than image quality.
Image files are smaller, which is better when attaching images to e-mail. However, images are relatively coarser.
• The initial factory default image size setting is 9M (9 million pixels).
x
• Selecting 3:2 (3456
2304 pixels) records images with an aspect ratio of 3:2, which
matches the standard aspect ratio of print paper.
• The letters “HDTV” stand for “High Definition Television”. An HDTV screen has an aspect ratio of 16:9, which makes them wider than the usual 4:3 aspect ratio of television screens of the past. Your camera can record images that are compatible with the aspect ratio an HDTV screen.
• You should regard the print paper sizes suggested here as guidelines only (200 dpi print resolution).
25
Snapshot Tutorial

Using Flash (Flash)

>?<
¥
N
1. In the REC mode, press [2] ( ) once.
2. Use [4] and [6] to select the flash setting
you want and then press [SET].
When the “R Panel” menu item (page 96) is “Off” (so the Control Panel is not displayed), pressing [2] ( ) will cycle through the available flash settings.
Auto Flash
Flash fires automatically in accordance with exposure (amount of light and brightness) conditions.
Flash Off Flash does not fire.
Flash always fires. This setting can be used to brighten a
Flash On
subject that normally comes out dark due to daylight or backlight (daylight synchro flash).
Red Eye
Reduction
Flash fires automatically. This type of flash can be used to reduce the chance of redness in the subject’s eyes.
3. Press the shutter button to shoot.
Back lamp
2
< indicates the flash will fire.
Flashes orange while the flash is charging to indicate that image recording is disabled.
• You will not be able to take another flash snapshot until the lamp stops flashing orange, which indicates that charging is complete.
Flash
[2] ( )
26
Snapshot Tutorial
NOTE
• Take care so your fingers and the strap do not block the flash.
• The desired effect may not be obtained when the subject is too far away or too close.
• Flash charging time depends on operating conditions (battery condition, ambient temperature, etc.) With a fully charged battery it takes anywhere from a few seconds to 7 seconds.
• Shooting with flash turned off when lighting is dim results in a slow shutter speed, which can cause image blur due to camera movement. Under such conditions, secure the camera with a tripod, etc.
• With red eye reduction, the flash is fired automatically in accordance with exposure. It does not fire in areas where lighting is bright.
• The presence of outdoor sunlight, fluorescent lighting, or some other light source can cause abnormal image colors.
• Select “Flash Off” for the flash setting when shooting in areas where flash photograph is prohibited.
• Approximate Flash Range (ISO Sensitivity: Auto) Wide Angle: 0.15 m to 2.8 m (0.5' to 9.2') Telephoto: 0.4 m to 1.5 m (1.3' to 4.9') * The above values depend on the optical zoom setting.
Red-eye Reduction
Using the flash to shoot at night or in a dimly lit room can cause red spots inside the eyes of people who are in the image. This is caused when the light from the flash reflects off of the retina of the eye. When red-eye reduction is selected as the flash mode, the camera fires a pre-flash to cause the irises in the eyes of any people in the image to close, which reduces the chance of red eye. Note the following important points when using red-eye reduction.
• Red-eye reduction does not work unless the people in the image are looking directly at the camera (flash).
• Red-eye reduction may not work very well if the subjects are located far away from the camera.
Other Useful Flash Features
• Changing the flash intensity (page 60)
B
27
Snapshot Tutorial

Using Face Detection (Face Detection)

The face detection feature adjusts focus and brightness to the faces in the image.
1. In the REC mode, press [SET].
2. Use [8] and [2] to select the third Control Panel option from the top
(Face Detection).
3. Use [4] and [6] to select “G Face Detection: On” and then press
[SET].
4. Point the camera at the subject(s).
The camera will detect human faces and display a frame around each one.
5. Half-press the shutter button.
The camera will focus and the frames around the faces it focuses on will turn green.
6. Press the shutter button the rest of the way down.
. To give priority to detection speed or number of faces
1. In the REC mode, press [SET].
2. Use [8] and [2] to select the third Control Panel option from the top
(Face Detection).
3. Use [4] and [6] to select “L Priority” and then press [SET].
4. Use [8] and [2] to select the setting you want, and then press [SET].
Speed
Quantity
Minimizes face detection time, and limits the number of faces that can be detected at one time to five.
Enables detection of a maximum of five to ten faces. With this setting, the camera detects faces in the image that are smaller and further away from the camera.
28
Snapshot Tutorial
Tips for Best Face Detection Results
• The camera performs center focus if it cannot detect a face.
• Always make sure that Auto Focus (AF) is selected as the focus mode when shooting with face detection.
• Face detection may take a bit longer when you hold the camera sideways.
• Detection of the following types of faces is not supported. – Face that is obstructed by hair, sunglasses, a hat, etc., or a face in dark shade – A profile or a face that is at an angle – A face that is very far away and small, or very close and large – A face in an area that is very dark – The face of a pet or some other non-human subject
IMPORTANT!
• Face detection cannot be used in combination with any of the following features. – Some BEST SHOT scenes (Movie, For YouTube, Voice Recording)
• The following functions are disabled when shooting with face detection. – Multi AF
29
Snapshot Tutorial

Reducing the Effects of Camera and Subject Movement (Anti Shake)

You can turn on the camera’s Anti Shake feature to reduce image blur due to subject movement or camera movement when shooting a moving subject using telephoto, when shooting a fast-moving subject, or when shooting under dim lighting conditions.
1. In the REC mode, press [SET].
2. Use [8] and [2] to select the fourth Control Panel option from the top
(Anti Shake).
3. Use [4] and [6] to select the setting you want and then press [SET].
Auto Minimizes the effects of hand and subject movement.
Off Turns off Anti Shake settings
NOTE
• ISO sensitivity, aperture, and shutter speed do not appear on the monitor screen when you half-press the shutter button while “Auto” is selected. These values will appear briefly, however, in the preview image that is displayed immediately after you shoot a snapshot.
• If the flash fires, the Anti Shake icon S will remain on the display, even though Anti Shake does not function during flash photography.
• Shooting with Anti Shake can cause an image to appear somewhat coarser than normal and can cause slight deterioration of image resolution.
• Anti Shake may not be able to eliminate the effects of camera or subject movement when movement is severe.
• Anti Shake is disabled during movie recording.
30
Snapshot Tutorial

Specifying ISO Sensitivity (ISO)

ISO sensitivity is a measure of sensitivity to light.
1. In the REC mode, press [SET].
2. Use [8] and [2] to select the fifth Control Panel option from the top
(ISO Sensitivity).
3. Use [4] and [6] to select the setting you want and then press [SET].
AUTO Adjusts sensitivity automatically according to conditions
ISO 64 Lower sensitivity
ISO 100
ISO 200
ISO 400
ISO 800
ISO 1600
• “AUTO” ISO sensitivity always is applied for movies, regardless of the current ISO sensitivity setting.
Higher sensitivity
Slow shutter speed
Fast shutter speed (Set for shooting in dimly lit areas.)
Less noise
Some coarseness (increased digital noise)

Adjusting White Balance (White Balance)

You can adjust white balance to match the source of light available where you are shooting and avoid the blue cast that results when shooting outdoors when it is cloudy, and the green cast that results when shooting under fluorescent lighting.
1. In the REC mode, press [SET].
2. Use [8] and [2] to select the sixth Control Panel option from the top
(White Balance).
31
Snapshot Tutorial
3. Use [4] and [6] to select the shooting condition you want and then
press [SET].
Auto WB Configures the camera to adjust white balance automatically
Daylight For shooting outdoors on a clear day
Overcast
Shade For shooting on a clear day in the shade of trees or buildings
Day White
Fluorescent
Daylight
Fluorescent
Tungsten For shooting under light bulb lighting
Manual WB
• When “ Auto WB” is selected for the white balance setting, the camera automatically determines the white point of the subject. Certain subject colors and light source conditions can cause problems when the camera tries to determine the white point, which makes proper white balance adjustment impossible. If this happens, select the white balance setting that matches your shooting conditions (Daylight, Overcast, etc.)
For shooting outdoors on an overcast rainy day, in the shade, etc.
For shooting under white or day white fluorescent lighting
For shooting under daylight fluorescent lighting
For configuring the camera manually to suit a particular light source.
Select “· Manual WB”.
1
Under the lighting conditions you plan
2
to use when shooting, point the camera at a blank white piece of paper so it fills the entire monitor screen and then press the shutter button. Press [SET].
3
The white balance setting is retained even if you turn off the camera.
Blank white paper
32
Snapshot Tutorial

Correcting Image Brightness (EV Shift)

You can manually adjust an image’s exposure value (EV value) before shooting it.
• Exposure Compensation Range: –2.0EV to +2.0EV
• Unit: 1/3EV
1. In the REC mode, press [SET].
2. Use [8] and [2] to select the third Control Panel option from the
bottom (EV Shift).
3. Use [4] and [6] to adjust the exposure compensation value.
[6]: Increases the EV value. A higher EV
value is best for light-colored subjects and backlit subjects.
[4]: Decreases the EV value. A lower EV
value is best for dark-color subjects and for shooting outdoors on a clear day.
To cancel exposure compensation, change the EV value to 0.0.
4. Press [SET].
This applies the exposure compensation value. The exposure compensation value you set remains in effect until you change it.
NOTE
• When shooting under very dark or very bright conditions, you may not be able to obtain satisfactory results even after performing exposure compensation.
Exposure compensation value
33
Snapshot Tutorial

Using the easy Mode

The easy mode eliminates troublesome setups. This mode is recommended for those who are new to digital imaging.
1. In the REC mode, press [SET].
2. Use [8] and [2] to select the second Control Panel option from the
bottom (easy Mode).
3. Use [4] and [6] to select “
This enters the easy mode.
|
On” and then press [SET].
4. Focus the image.
While the focus frame is aligned with the subject, half-press the shutter button.
5. Shoot the image.
When the image is focused, press the shutter button the rest of the way. This records the snapshot.
. Using the easy Menu
The easy menu contains flash, self-timer, and image size settings, plus an item for exiting the easy mode. While the camera is in the easy mode, all the other settings (besides Flash, Self­timer, Image Size, and easy Mode) on the REC tab menu (page 124) and Quality tab menu (page 125) are fixed at preset optimum values. Any settings you configured on these tabs are not used in the easy mode.
IMPORTANT!
• To use the Set Up tab menu (page 125), you need to exit the easy mode. To do this, select the “easy Mode” item in step 2 of the following procedure, and then
l
select do.
in step 3. After that, you can use the Set up tab menu as you normally
1. Press [MENU].
The easy menu displays larger text than standard menus.
2. Use [8] and [2] to select the menu item you
want, and then press [SET].
34
Snapshot Tutorial
3. Use [8] and [2] to select the setting you want, and then press [SET].
Menu Item: Available Settings:
Flash > (Auto Flash)* / < (Flash On) / ? (Flash Off)
Self-timer (10-second self-timer) / l*
Image Size :* / $ / !
easy Mode k / l*
Exit Menu Exit the easy menu
• An asterisk (*) indicates reset default settings.
• See the following for details. – Flash (page 26) – Self-timer (page 52) – Image Size (page 24)
• The following are the settings you can select for “easy Mode”.
To do this:
Stay in the easy mode, without switching to another recording type
Switch from the easy mode to a standard recording type l
• On-screen pop-up help text provides a brief explanation of each setting.
Select this setting:
k
35
Snapshot Tutorial

Changing the Control Panel Date/Time Style

1. In the REC mode, press [SET].
2. Use [8] and [2] to select the bottom Control Panel option (Date/Time).
Use [4] and [6] to select the date or time.
NOTE
• You can select either of two display style (page 100) for the date: Month/Day or Day/Month.
• The time is displayed using 24-hour format.

Shooting with Zoom

Your camera provides you with 3X optical zoom (that changes the lens focal distance), which can be used in combination with digital zoom (that digitally processes the center portion of the image to enlarge it) for total zoom capabilities of 3X to 45.2X. The image deterioration point depends on the image size (page 38).
1. In the REC Mode, press the zoom button to zoom.
Zoom button
z Telephoto w Wide Angle
z (Telephoto) : Enlarges the subject and narrows the range w (Wide Angle) : Reduces the size of the subject and broadens the range
2. Press the shutter button to shoot the image.
IMPORTANT!
• Digital zoom is disabled while date stamping (page 99) is turned on.
36
Snapshot Tutorial
NOTE
• The higher the digital zoom factor, the coarser the recorded image. Note that the camera also has a function that lets you record using digital zoom without image deterioration (page 38).
• Use of a tripod is recommended to protect against image blur due to camera movement when shooting with telephoto.
• Performing a zoom operation changes the lens aperture.
• Digital zoom only is available during movie recording. You can adjust the optical zoom setting before you press the shutter button to start movie recording.

Optical Zoom and Digital Zoom Switch Point

If you hold down the z (Telephoto) side of the zoom button, the zoom operation will stop when the optical zoom factor reaches its maximum. Momentarily releasing the zoom button and then holding down its z (Telephoto) side will switch to digital zoom, which you can use to set an even higher zoom factor.
• During zoom, a zoom bar on the monitor screen shows the current zoom setting.
Image deterioration indicator
Focusing range (Displayed for Auto Focus, Macro Focus, and Manual Focus.)
Zoom bar
Undeteriorated image quality range
1X
Optical/digital zoom switch point
* 3X optical zoom point
Image deterioration
Deteriorated image quality range
3X to 16X
12X to 45.2X
Zoom pointer (Indicates current zoom.)
37
Snapshot Tutorial
• The image deterioration point depends on the image size (page
24). The smaller the image size, the higher the zoom factor you can use before reaching the image deterioration point.
• Though digital zoom generally causes a deterioration of image quality, some digital zoom without image deterioration is possible with image sizes of “7M” and smaller. The range in which you can use digital zoom without image deterioration is indicated on the display. The deterioration point depends on the image size.
Image
Size
Maximum
Zoom Factor
Undeteriorated
zoom limit
9M 12X 3X
3:2 12X 3X
16:9 12X 3X
7M 13.5X 3.4X
4M 17.9X 4.5X
2M 25.6X 6.5X
VGA 45.2X 16X
38
Snapshot Tutorial

Recording Movie Images and Audio

To record a movie

1. Configure the quality setting for the movie (page 58).
The length of the movie you can record will depend on the quality setting you select.
2. In the REC mode, press [BS].
3. Use [8], [2], [4], and [6] to select the »
Remaining recording time
(Movie) scene and then press [SET].
This causes » to appear on the monitor screen.
4. Press the shutter button.
This will start recording and display Y on the monitor screen. Movie recording includes monaural audio.
5. Press the shutter button again to stop
recording.
Movie recording also will stop automatically if memory becomes full before you press the shutter button.
• The maximum size allowed for a single movie file is 4GB. Movie recording stops automatically when a file becomes 4GB.
NOTE
• Spending a long time using movie recording will cause the camera to become slightly warm to the touch. This is normal and does not indicate malfunction.
• The camera also records audio. Note the following points when shooting a movie. – Take care that the microphone is not blocked by your fingers,
etc.
– Good recording results are not possible when the camera is too
far away from what you are trying to record.
– Operating camera buttons while shooting can cause button
noise to be picked up in the audio.
• Shooting a very bright subject can cause a vertical band to appear in the monitor screen image. This does not indicate malfunction. The band will not be recorded in a snapshot, but will be recorded in the case of a movie.
• Use of certain types of memory cards increase the time it takes to record movies, which can cause movie frames to be lost. This condition is indicated by » and Y flashing on the monitor screen. To avoid loss of movie frames, use of a memory card with a maximum transfer speed of at least 10MB per second is recommended.
Recording time
Microphone
39
Recording Movie Images and Audio
• Only digital zoom can be used for zooming during movie recording. Since optical zoom is not possible while recording a movie, zoom as required before pressing the shutter button to start recording.
• The effects of camera movement in an image become more pronounced when you shoot close up or with a large zoom factor. Because of this, use of a tripod is recommended under these conditions.

Recording Audio Only (Voice Recording)

Voice Recording lets you record audio only, without a snapshot or movie. You can record about 55 minutes and 35 seconds of Voice Recording using the camera’s built-in memory only.
1. In the REC mode, press [BS].
2. Use [8], [2], [4], and [6] to select the
`
(Voice Recording) scene
and then press [SET].
This causes ` to appear on the monitor screen.
3. Press the shutter button to start recording.
• The back lamp flashes green while recording is in progress.
• Pressing [SET] during recording will insert a marker into the recording. During playback, you will be able to jump to the markers in the recording.
4. Press the shutter button again to stop audio
recording.
• To create another audio recording file, repeat steps 3 and 4.
• To turn off Voice Recording, press [BS] and then select t (Auto).
NOTE
• You can use [8] (DISP) during audio recording to toggle the monitor screen on
and off.
• When monitor screen contents are turned off, selecting the “Voice Recording” scene will cause the monitor screen to turn off immediately (page 105).
Recording time
Remaining recording time
40
Recording Movie Images and Audio
About audio data
• Audio files can be played back on a computer using Windows Media Player or QuickTime (pages 84, 92) – Audio Data: WAVE/IMA-ADPCM (WAV extension) – Audio File Size: Approximately 165KB (Approximately 30 seconds of recording
at 5.5KB per second)

To play back an audio recording

1. In the PLAY mode, use [4] and [6] to display
the Voice Recording file you want to play.
` is displayed in place of an image for a Voice Recording file.
2. Press [SET] to start playback.
Voice Recording Playback Controls
Fast forward/fast reverse [4] [6]
Play/pause [SET]
Jump to marker
Volume adjustment Press [2] and then press [8] [2]
Monitor screen on/off [8] (DISP)
Playback end [MENU]
While playback is paused, press [ jump to the next marker and then press [SET] to resume playback.
4] or [6] to
41
Recording Movie Images and Audio

Using BEST SHOT

What is BEST SHOT?

BEST SHOT provides you with a collection of sample “scenes” that show a variety of different types of shooting conditions. When you need to change the setup of the camera, simply find the scene that matches what you are trying to achieve, and the camera sets up for it automatically. This helps to minimize the chance of ruined images due to poor exposure and shutter speed settings.

Some Sample Scenes

Portrait Scenery Night Scene Night Scene Portrait

To shoot an image with BEST SHOT

1. In the REC mode, press [BS].
This will display a menu of BEST SHOT scenes.
• The initial default selection is t (Auto).
2. Use [8], [2], [4], and [6] to move the
boundary to the scene you want to select.
• The scene menu has multiple pages. Use [8]
2] to scroll between menu pages.
and [
• You can access information about the currently selected scene. See page 44 for details.
• To return to normal snapshot recording, select Scene 1 t (Auto). Pressing [MENU] while the scene selection screen or scene information screen is displayed will cause the boundary to jump directly to t (Auto).
42
Currently selected scene (with boundary)
Scene name
Scene number
Using BEST SHOT
3. Press [SET] to configure the camera with the settings for the currently
selected scene.
This returns to the REC mode.
• The settings of the scene you selected remain in effect until you select a different scene.
• To select a different BEST SHOT scene, repeat the above procedure from step 1.
4. Press the shutter button.
NOTE
• The BEST SHOT YouTube scene sets up the camera for recording movies that are optimized for uploading to YouTube. Movies recorded with the YouTube scene are stored in a special folder to make them easy to locate for uploading (page 94). Maximum recording time while the YouTube scene is selected is 2 minutes.
43
Using BEST SHOT
. Using Scene Information Screen
To find out more about a scene, select it with the boundary on the scene selection screen, and then press the zoom button.
• To return to the scene menu, press the zoom button again.
• To scroll between scenes, use [
• To configure the camera with the settings for the currently selected scene, press [SET]. To return to the scene information screen for the currently selected BEST SHOT scene, press [BS].
4] and [6].
44
Using BEST SHOT
. BEST SHOT Precautions
• Selecting the Night Scene or Fireworks scene results in a slow shutter speed setting. Since a slow shutter speed increases the chance of digital noise in the image, the camera automatically performs a digital noise reduction process when either of these scenes is selected. This means that it will take a bit longer for the image to be saved which is indicated by the back lamp flashing green. Do not perform any key operation during that time. Also, it is a good idea to use a tripod to avoid image blur due to camera movement when shooting at slow shutter speeds.
• Your camera includes a sample scene that optimizes settings for auction site images. Depending on your camera model, the sample scene is named either “For eBay” or “Auction”. Images you record using the auction site sample scene are stored in a special folder so you can easily find them on your computer (page 94).
• High Sensitivity – The high sensitivity setting is disabled whenever the camera’s flash fires. – High sensitivity may not produce the desired results in very dark conditions. – When shooting with slow shutter speeds, use a tripod to protect against blurring
due to camera movement.
– Under certain lighting conditions, the camera will perform an automatic noise
filtering operation to reduce digital noise in the image. This operation causes the camera to take longer than normal to save the image and be ready for the next shot.
• BEST SHOT scene images were not shot using this camera.
• Images shot using a BEST SHOT scene may not produce the results you expected due to shooting conditions and other factors.
• You can modify the camera settings that are made after you select a BEST SHOT scene. Note, however, that the BEST SHOT settings revert to their defaults when you select another BEST SHOT scene or turn off the camera.
45
Using BEST SHOT

Advanced Settings

The following are menu operations you can use to configure various camera settings.
• You also can use the Control Panel (page 23) to configure some of the settings that appear on the menu screen. Refer to the page references provided in this section for information about configuring settings using the Control Panel.

Using On-screen Menus

. Example Menu Screen Operation
Press [MENU] to display the menu screen.
• Menu contents are different in the REC mode and PLAY mode.
Example: REC mode menu
[MENU]
Menu Screen Operation Buttons
[4] [6]
[8] [2] Selects a setting option.
[SET] Registers the selected setting.
[MENU] Exits the menu screen.
Selects tabs. [ setting.
1. In the REC mode, press [MENU].
This will display the menu screen.
6] is also used to display the options available for a
2. Use [4] and [6] to select the tab where the item you want to configure
is located.
46
Advanced Settings
3. Use [8] and [2] to select the menu item
you want, and then press [6].
4. Use [8] and [2] to change the setting.
Example: When “Focus” is selected on the “REC” tab
Tabs
5. After the setting is the way you want, press
[SET].
• Pressing [4] registers the selected setting and
returns to the menu.
• To configure settings on another tab after pressing [ move the highlighting up to the tabs, and then use [
. Menu Operations in This Manual
Menu operations are represented in this manual as shown below. The following operation is the same one described under “Example Menu Screen Operation” on page 46.
[r] (REC) * [MENU] * REC Tab * Focus
4] to return to the menu, use [8] to
4] and [6] to select the tab you want.
Use [4] and [6] to select the “REC” tab.
Procedure
Settings
Press [MENU].Press [r] (REC).
Use [8] and [2] to select the “Focus” and then press [6].
47
Advanced Settings

REC Mode Settings (REC)

Selecting a Focus Mode (Focus)

Procedure
[r] (REC) * [MENU] * REC Tab * Focus
Settings Type of Shot
Q Auto Focus
´ Macro
E Pan
Focus
) Infinity
W Manual Focus
General recording
Close ups Automatic
Shooting with a relatively wide focus range
Scenery and other distant subjects
When you want to focus manually
Focus Mode Approximate Focus Range*
Snapshot Movies Snapshot Movies
Approximately
2
*
Automatic
40 cm to 9 (infinity) (1.3
' to 9)
Approximately
Fixed
focal point
Fixed
focal point
15 cm to 50 cm
'' to 19.7'')
(5.9
Fixed distance
*
3, *4
Fixed distance
3, *5
*
Fixed Infinity
Manual
Approximately 15 cm to 9 (infinity)
3
*
(5.9'' to 9)
*1 The focus range is the distance from the lens surface. *2 During movie recording, the Auto Focus mode is disabled. *3 The minimum changes along with the optical zoom setting. *4 The distance depends on shooting conditions, and appears on the monitor screen
when the shutter button is half-pressed.
1
2
*
48
Advanced Settings
*5 (m)
Normal Macro
Zoom Steps Close Up Telephoto Center distance
Z1 (Wide) Approx. 2.0 (6.6
2 Approx. 2.7 (8.9') 9 0.40 (15.7'')
3 Approx. 4.0 (13.1') 9 0.40 (15.7'')
4 Approx. 5.0 (16.4') 9 0.40 (15.7'')
5 Approx. 5.6 (18.4') 9 0.40 (15.7'')
6 Approx. 7.3 (24.0') 9 0.40 (15.7'')
7 (Tele) Approx. 8.0 (26.2') 9 0.40 (15.7'')
NOTE
• Above values are for reference only. For movie macro, the focus range is a few centimeters within the center distance.
') 9 0.40 (15.7'')
To focus with manual focus
1. On the monitor screen, compose the image
so the subject you want to focus on is within the yellow boundary.
2. Watching the image on the monitor screen
use [4] and [6] to adjust focus.
• At this time the image that is within the boundary will enlarge and fill the monitor screen, which aids in focusing. If you do not perform any operation for two seconds while the enlarged image is displayed, the screen in step 1 will re-appear.
Yellow boundary
49
Advanced Settings
NOTE
• Auto Focus can be used when recording snapshots only.
• Whenever you perform an optical zoom operation while shooting with Auto Focus, Macro Focus, or Manual Focus, a value will appear on the monitor screen to tell you the focus range, as shown below. Example: oo cm to 9
* oo is the actual focusing range value.
• The operations assigned to the [
54) are disabled while Manual Focus is selected as the focus mode.
4] and [6] keys with the “L/R Key” setting (page
Using Focus Lock
“Focus lock” is a technique you can use when you want to compose an image in which the subject you want to focus on is not within the focus frame in the center of the screen.
• To use focus lock, select “U Spot” for the Auto Focus area (page 53).
1. Align the monitor screen’s focus frame with
the subject you want to focus on and then half-press the shutter button.
2. Keeping the shutter button half-pressed
(which maintains the focus setting), move the camera to compose the image.
3. When you are ready to shoot the image,
press the shutter button the rest of the way down.
NOTE
• Focus lock also locks exposure (AE).
Subject to be focused on
Focus frame
50
Advanced Settings

Using Continuous Shutter (Continuous)

Procedure
[r] (REC) * [MENU] * REC Tab * Continuous
While Continuous Shutter is turned on, images are continually recorded until memory becomes full, as long as you keep the shutter button depressed. Releasing the shutter button stops shooting.
NOTE
• With continuous shutter, exposure and focus for the first image are applied for successive images as well.
• Continuous shutter cannot be used in combination with any of the following. Some BEST SHOT scenes (Movie, For YouTube, Voice Recording)
• When using a continuous shutter mode, keep the camera still until all recording is finished.
• The continuous shutter rate depends on the current image size and image quality settings.
• The speed of Continuous Shutter depends on the type of memory card loaded in the camera and the amount of free space available for storage. When shooting to built-in memory, continuous shutter shooting is relatively slow.
• You cannot use the self-timer in combination with Continuous Shutter.
51
Advanced Settings

Using the Self-timer (Self-timer)

Procedure
[r] (REC) * [MENU] * REC Tab * Self-timer
With the Self-timer, pressing the shutter button starts a timer. The shutter is released and the image is shot after a fixed amount of time.
10 sec 10-second Self-timer
2-second Self-timer
2 sec
X3 (Triple Self-timer)
Off Turns off the Self-timer.
• The front lamp flashes while the Self-timer countdown is in progress.
• You can interrupt an ongoing Self-timer countdown by pressing [SET].
NOTE
• The Self-timer cannot be used together with the following features. Continuous Shutter, certain BEST SHOT scene (Voice Recording)
• The Triple Self-timer cannot be used together with the following features. Some BEST SHOT scenes (Movie, For YouTube)
• When shooting under conditions that slow down the shutter speed, you can use this setting to prevent image blur due to camera movement.
Shoots three images: one image 10 seconds after the shutter button is pressed, and the next two images as soon as the camera is ready after shooting the previous image. How long it takes for the camera to get ready to shoot depends on the image size and quality settings, whether or not a memory card is loaded in the camera, and the flash charge condition.
Front lamp
52
Advanced Settings

Shooting with Face Detection (Face Detection)

Procedure
[r] (REC) * [MENU] * REC Tab * Face Detection
For details, see the Control Panel procedure on page 28.

Reducing the Effects of Camera and Subject Movement (Anti Shake)

Procedure
[r] (REC) * [MENU] * REC Tab * Anti Shake
For details, see the Control Panel procedure on page 30.

Specifying the Auto Focus Area (AF Area)

Procedure
[r] (REC) * [MENU] * REC Tab * AF Area
Spot
Multi
• “Multi” cannot be selected for the Auto Focus area while you are using Face Detection (page 28).
This mode takes readings of a small area in the center of the image. This setting works well with focus lock (page 50).
When you half-press the shutter button while this setting selected, the camera will select the optimum Auto Focus area from among nine possible areas. The focus frame of the area where the camera focuses will be displayed in green.
U
Spot” I Multi”
Focus frame
53
Focus frame
Advanced Settings

Using the easy Mode (easy Mode)

Procedure
[r] (REC) * [MENU] * REC Tab * easy Mode
For details, see the Control Panel procedure on page 34.
Assigning Functions to the [4] and [6] Keys (L/R Key)
Procedure
[r] (REC) * [MENU] * REC Tab * L/R Key
You can assign one of the five functions listed below to the [4] and [6] keys.
Setting [4]/[6] key operation
Metering Changes the Metering Mode (page 59)
EV Shift Adjusts the EV shift value (page 33)
White Balance Changes the white balance setting (page 58)
ISO Changes the ISO Sensitivity setting (page 31)
Self-timer Sets the self-timer time (page 52)
Off Cancels [
4] and [6] key assignments

Displaying the On-screen Grid (Grid)

Procedure
[r] (REC) * [MENU] * REC Tab * Grid
The on-screen grid can be displayed on the REC mode monitor screen for easy vertical and horizontal alignment when composing images.
54
Advanced Settings

Turning Digital Zoom On or Off (Digital Zoom)

Procedure
[r] (REC) * [MENU] * REC Tab * Digital Zoom
You can use this setting to turn digital zoom on or off. When digital zoom is turned off, operating the zoom button zooms the image with optical zoom only.

Turning on Image Review (Review)

Procedure
[r] (REC) * [MENU] * REC Tab * Review
While Review is turned on, the camera will display a image for about one second immediately after you press the shutter button to record it.

Using Icon Help (Icon Help)

Procedure
[r] (REC) * [MENU] * REC Tab * Icon Help
While Icon Help is turned on, a textual description will appear on the display for certain icons when you switch between REC functions.
Functions Supported by Icon Help
• REC Mode, Flash, Metering Mode, White Balance, Self-timer, EV Shift
55
Advanced Settings

Configuring Power On Default Settings (Memory)

Procedure
[r] (REC) * [MENU] * REC Tab * Memory
When you turn off the camera, it remembers the current settings of all enabled memory items and restores them when you turn it back on. Any memory item that is disabled will be returned to its initial default setting whenever you turn off the camera.
Setting Disabled (Initial Default Setting) Enabled
b
BEST SHOT Snapshot (Auto)
Flash Auto
Focus AF (Auto Focus)
White Balance Auto
ISO Auto
AF Area Spot
Metering Multi
Self-timer Off
Flash Intensity 0
Digital Zoom On
MF Position Position before manual focus was selected.
Zoom Position
* Full wide
* Optical zoom setting only.
• If you turn the camera power off and then back on while the BEST SHOT memory item is enabled, all of the other memory items (except for zoom position) are initialized to the currently selected BEST SHOT sample scene setup, regardless of the enabled/disabled status of the other memory items.
Setting at power off
56
Advanced Settings

Image Quality Settings (Quality)

Specifying Snapshot Size (Size)

Procedure
[r] (REC) * [MENU] * Quality Tab * Size
For details, see the Control Panel procedure on page 25.

Specifying Snapshot Image Quality (Quality (Snapshot))

Procedure
[r] (REC) * [MENU] * Quality Tab * t Quality (Snapshot)
Fine Gives image quality priority
Normal Normal
Economy Gives number of images priority
• The “Fine” setting helps to bring out details when shooting a finely detailed image of nature that includes dense tree branches or leaves, or an image of a complex pattern.
• Memory capacity (the number of images you can record) will be affected by the quality settings you configure (page 133).
57
Advanced Settings

Specifying Movie Image Quality (Quality (Movie))

Procedure
[r] (REC) * [MENU] * Quality Tab * » Quality (Movie)
Movie image quality is a standard that determines the detail, smoothness, and clarity of a movie during playback. Shooting with the high-quality (HQ) setting will result in better image quality, but it also shortens the amount of time you can shoot.
Image Quality (Pixels) Approximate Data Rate Frame Rate
x
HQ 640
Normal 640
LP 320
480 10.6 Megabits/second
x
480 12.5 Megabits/second
x
480 6.2 Megabits/second
x
240 2.7 Megabits/second 15 frames/second
30 frames/secondHQ Wide 848

Correcting Image Brightness (EV Shift)

Procedure
[r] (REC) * [MENU] * Quality Tab * EV Shift
For details, see the Control Panel procedure on page 33.

Controlling White Balance (White Balance)

Procedure
[r] (REC) * [MENU] * Quality Tab * White Balance
For details, see the Control Panel procedure on page 31.

Specifying ISO Sensitivity (ISO)

Procedure
[r] (REC) * [MENU] * Quality Tab * ISO
For details, see the Control Panel procedure on page 31.
58
Advanced Settings

Specifying the Metering Mode (Metering)

Procedure
[r] (REC) * [MENU] * Quality Tab * Metering
The metering mode determines what part of the subject is metered for exposure.
Multi-pattern metering divides the image into sections and
Multi
Center
Weighted
Spot
• The currently selected metering mode is indicated by an icon on the snapshot screen. No icon is displayed when “Multi” is selected as the metering mode.
measures the light in each section for a balanced exposure reading. This type of metering provides error-free exposure settings for a wide range of shooting conditions.
Center weighted metering concentrates on the center of the focus area to measure light. This type of metering is best when you want some level of control over contrast.
Spot metering takes readings at a very small area. Use this metering method when you want exposure to be set according to the brightness of a particular subject, without being affected by surrounding conditions.

Using Built-in Color Filters (Color Filter)

Procedure
[r] (REC) * [MENU] * Quality Tab * Color Filter
Settings: Off, B/W, Sepia, Red, Green, Blue, Yellow, Pink, and Purple

Controlling Image Sharpness (Sharpness)

Procedure
[r] (REC) * [MENU] * Quality Tab * Sharpness
You can specify one of five sharpness settings from +2 (sharpest) to –2 (least sharp).
59
Advanced Settings

Controlling Color Saturation (Saturation)

Procedure
[r] (REC) * [MENU] * Quality Tab * Saturation
You can specify one of five saturation settings from +2 (most saturated) to –2 (least saturated).

Adjusting Image Contrast (Contrast)

Procedure
[r] (REC) * [MENU] * Quality Tab * Contrast
You can specify one of five contrast settings from +2 (most contrast between light and dark) to –2 (least contrast between light and dark).

Specifying Flash Intensity (Flash Intensity)

Procedure
[r] (REC) * [MENU] * Quality Tab * Flash Intensity
You can specify one of five flash intensity settings from –2 (weakest) to +2 (strongest).
• Flash intensity may not change when the subject is too far away or too close.
60
Advanced Settings

Viewing Snapshots and Movies

Viewing Snapshots

See page 19 for the procedure for viewing snapshots.

Viewing a Movie

1. Press [p] (PLAY) and then use [4] and [6] to display the movie you
want to view.
2. Press [SET] to start
playback.
Movie icon: »
Recording time
Image quality
Movie Playback Controls
Fast forward/ fast reverse
Play/pause [SET]
1 frame forward/back
Volume adjustment
Information display on/off
Zoom
Stop playback [MENU]
• Playback may not be possible for movies not recorded with this camera.
[4] [6]
• Each press of either button increases the speed of the fast forward or fast reverse operation.
• To return to normal playback speed, press [SET].
[4] [6]
• Holding down either button scrolls continuously.
Press [2] and then press [8] [2]
• Volume can be adjusted only while movie playback is in progress.
[8] (DISP)
Press the zoom button z ([).
• You can use [8], [2], [4], and [6] to scroll the zoomed image on the monitor screen. You can zoom a movie image up to 4.5 times normal size.
61
Viewing Snapshots and Movies

Zooming an On-screen Image

1. In the PLAY mode, use [4] and [6] to scroll through the images until
the one you want is displayed.
2. Press the zoom button z ([) to zoom.
You can use [8], [2], [4], and [6] to scroll the zoomed image on the monitor screen. Press the zoom button w to unzoom the image.
– If display indicators are turned on, an indicator
in the lower right corner of the monitor screen shows what part of the zoomed image is currently displayed.
– To exit the zoom screen, press [MENU] or
[BS].
– Though the maximum image zoom factor is
8X, certain image sizes may not allow zooming up to the full 8X.

Displaying 12 Images on the Same Screen

1. In the PLAY Mode, press the zoom button w
(]).
Use [4] and [6] to scroll, 12 images at a time. To view a particular image, use [8], [2], [4], or [6] to move the selection boundary to the image you want and then press [SET].
Zoom factor
Image area
Current display area
Boundary
62
Viewing Snapshots and Movies

Viewing Snapshots and Movies on a TV Screen

1. Use the AV cable that comes with the camera to connect it to the TV.
Yellow
TV
AUDIO IN jacks (white)
VIDEO IN jack (yellow)
Making sure that the 6 mark on the camera is aligned with the 4 mark of the AV cable connector, connect the cable to the camera.
• Make sure that you insert the cable connector into the USB/AV port until you feel it click securely into place. Failure to insert the connector fully can result in poor communication or malfunction.
• Note that even while the connector is fully inserted, you still will be able to see the metal part of the connector as shown in the illustration.
White
AudioVideo
AV cable (bundled)
USB/AV port
2. Turn on the TV and select its video input mode.
If the TV has more than one video input, select the one where the camera is connected.
3. Press [p] (PLAY) to turn on the camera.
This will cause an image to appear on the TV screen, without anything appearing on the camera’s monitor screen.
• Pressing [ON/OFF] or [r] (REC) will not turn on the camera while the AV cable is connected.
• You also can change the aspect ratio of the screen and the video output system (page 103).
4. Now you can display images and play back movies as you normally do.
63
Viewing Snapshots and Movies
NOTE
• Audio is monaural.
• Certain TVs may cut off part of the images.
• Before connecting to a TV to display images, be sure to configure the camera’s
[r] (REC) and [p] (PLAY) buttons for “Power On” or “Power On/Off” (page 102).
• Audio is initially output by the camera at maximum volume. When you first start displaying images, set the TV volume control at a relatively low level and then adjust it as required.
• All icons and indicators that appear on the monitor screen also appear on the TV screen. You can use [8] (DISP) to change the display contents.
Recording Camera Images to a DVD Recorder or Video Deck
Use one of the following methods to connect the camera to the recording device using the camera’s bundled AV cable.
– DVD recorder or video deck: Connect to the VIDEO IN and AUDIO IN terminals. – Camera: USB/AV port
You can play a slideshow of snapshots and movies on the camera and record it on a DVD or video tape. When recording images to an external device, use [8] (DISP) to clear all indicators from the monitor screen (page 96). For information about connecting a monitor to the recording device and about how to record, see the user documentation that comes with the recording device you are using.
64
Viewing Snapshots and Movies

Other Playback Functions (PLAY)

This section explains menu items that you can use to configure settings and perform other playback operations.
For information about menu operations, see page 46.

Playing a Slideshow on the Camera (Slideshow)

Procedure
[p] (PLAY) * [MENU] * PLAY Tab * Slideshow
Start Starts the slideshow
Time
Interval
Effect
• To stop the slideshow, press [SET]. Pressing [MENU] instead of [SET] stops the slideshow and returns to the menu screen.
• Adjust audio volume by pressing [2] and then press [8] or [2] during playback.
• All button operations are disabled while the slideshow is transitioning from one image to another.
• The time required for transition from one image to another may be longer in the case of an image that was not recorded with this camera.
Time from the start to the end of the slideshow 1 to 5 minutes, 10 minutes, 15 minutes, 30 minutes, 60 minutes
Amount of time each image remains displayed Use [4] and [6] to select a value from 1 to 30 seconds, or “MAX”. If you specify a value from 1 to 30 seconds, images change at the specified interval, but the audio portion of movies and audio snapshots will continue to play until the end. When the slideshow reaches a movie file while “MAX” is selected, only the first frame of the movie will displayed. Voice Recording files are not played back when “MAX” is selected.
Turns effect on or off. On: Turns on the image change effect and background music. Off: No image change effect or background music
65
Other Playback Functions (PLAY)

Selecting Images for Printing (DPOF Printing)

Procedure
[p] (PLAY) * Snapshot Screen * [MENU] * PLAY Tab * DPOF Printing
See page 74 for details.

Protecting a File Against Deletion (Protect)

Procedure
[p] (PLAY) * [MENU] * PLAY Tab * Protect
Protects specific files.
Use [4] and [6] to scroll through the
1
files until the one you want to protect is displayed. Use [8] and [2] to select “On” and
On
All Files: On
• Note that even if a file is protected, it will be deleted if you perform the format operation (page 104).
2
then press [SET]. An image that is protected is indicated by the icon. To protect other files, repeat steps 1 and 2.
3
To exit the protect operation, press [MENU]. To unprotect a file, select “Off” instead of “On” in step 2 above.
Protects all files.
Use [8] and [2] to select “All Files: On” and then press [SET].
1
Press [MENU].
2
To unprotect all files, select “All Files: Off” instead of “All Files: On” in step 1 above.
66
Other Playback Functions (PLAY)

Rotating an Image (Rotation)

Procedure
[p] (PLAY) * Snapshot Screen * [MENU] * PLAY Tab * Rotation
1. Use [8] and [2] to select “Rotation” and then press [SET].
Each press of [SET] will rotate the displayed image 90 degrees left.
2. When the displayed image is at the orientation you want, press
[MENU].
NOTE
• Note that this procedure does not actually change the image data. It simply alters how the image is displayed on the camera’s monitor screen.
• An image that has been protected or zoomed and movie screen cannot be rotated.
• The original (unrotated) version of the image will be displayed on the 12-image screen.

Resizing a Snapshot (Resize)

Procedure
[p] (PLAY) * Snapshot Screen * [MENU] * PLAY Tab * Resize
You can reduce the size of a snapshot and save the result as a separate snapshot. The original snapshot is also retained. You can select resize an image to one of three image sizes: 7M, 4M, VGA.
• Resizing a 16:9 or 3:2 size snapshot will create an image with an aspect ratio of 4:3, with both sides cut off.
• The recording date of the resized version of the snapshot will be the same as the recording date of the original snapshot.
67
Other Playback Functions (PLAY)

Cropping a Snapshot (Trimming)

Procedure
[p] (PLAY) * Snapshot Screen * [MENU] * PLAY Tab * Trimming
You can crop a snapshot to trim parts you do not need, and save the result in a separate file. The original snapshot is also retained.
Use the zoom button to zoom the image to the size you want, use [8], [2], [4], and [6] to display the portion of the image you want to cut out, and then press [SET].
• The image produced by cropping a 3:2 or 16:9 image will have an aspect ratio of 4:3.
• The recording date of the cropped image will be the same as the recording date of the original snapshot.
Part of snapshot that is
Zoom factor
Represents
snapshot area
currently displayed

Adding Audio to a Snapshot (Dubbing)

Procedure
[p] (PLAY) * Snapshot Screen * [MENU] * PLAY Tab * Dubbing
You can add audio to a snapshot after you shoot it. You can re-record a snapshot’s audio whenever you want. You can record up to about 30 seconds of audio for a single snapshot.
1. Press the shutter button to start audio
recording.
68
Remaining recording time
Other Playback Functions (PLAY)
2. Press the shutter button again to stop audio recording.
• Take care that you do not block the camera’s microphone with your fingers while recording.
• Good recording results are not possible when the camera is too far away from what you are trying to record.
• Your camera supports the following audio data formats. – Audio Format: WAVE/IMA-ADPCM (WAV extension) – Approximate Audio File Size: 165KB (Approximately
30 seconds of recording at 5.5KB per second)
• Adding audio (dubbing) is not possible for the following types of images. – Protected images
• To delete audio, perform the following operation: Dubbing * Delete * [SET] * [MENU].
IMPORTANT!
• Note that you cannot restore the original audio of an Audio Snapshot after you delete or re-record it.
Microphone

To play snapshot audio

1. In the PLAY mode, use [4] and [6] to scroll through the images until
the Audio Snapshot you want is displayed.
An audio snapshot is one that has a ˆ icon.
2. Press [SET] to start playback.
Voice Recording Playback Controls
Fast forward/fast reverse [4] [6]
Play/pause [SET]
Volume adjustment
Display content switching [8] (DISP)
Stop playback [MENU]
• Audio of an Audio Snapshot also can be played back on a computer using Windows Media Player or QuickTime (pages 84, 92).
Press [2] and then press [8] [2]
69
Other Playback Functions (PLAY)

Copying Files (Copy)

Procedure
[p] (PLAY) * Snapshot Screen * [MENU] * PLAY Tab * Copy
Files can be copied from the camera’s built-in memory to a memory card or from a memory card to built-in memory.
Built-in * Card
Card * Built-in
NOTE
• You can copy snapshots, movies, audio snapshots, or Voice Recording files you recorded with this camera.
Copies all files from built-in camera memory to a memory card. This option copies all the files in built-in camera memory. It cannot be used to copy a single file.
Copies a single file on the memory card to camera built-in camera memory. Files are copied to the folder in built-in memory whose name has the largest serial number.
Use [4] and [6] to select the file you want to copy.
1
Use [8] and [2] to select “Copy” and then press [SET].
2
70
Other Playback Functions (PLAY)

Printing

Printing Snapshots

Professional Print Service
You can take a memory card that contains the images you want to print to a professional print service and have them printed.
Printing on a Home Printer
Printing Images on a Printer with Memory Card Slot
You can use a printer equipped with a memory card slot to print images directly from a memory card. For details, see the user documentation that comes with your printer.
Connecting Directly to a PictBridge Compatible Printer
You can print on a printer that supports PictBridge (page
72).
Printing with a Computer
Windows Computer
Install the software (Photo Loader with HOT ALBUM) that comes bundled with the camera on your computer.
• For details, see “To install Photo Loader with HOT ALBUM” on page 83.
Macintosh
After transferring the images to your Macintosh, use commercially available software to print.
• You can specify which images you want to print, the number of copies, and date stamp settings before printing (page 74).
71
Printing

Connecting Directly to a PictBridge Compatible Printer

You can connect the camera directly to a printer that supports PictBridge and print images without going through a computer.
. To set up the camera before connecting to a printer
1. Turn on the camera and press [MENU].
2. On the “Set Up” tab, select “USB” and then press [6].
3. Use [8] and [2] to select “PTP (PictBridge)”, and then press [SET].
. Connecting the Camera to a Printer
Use the USB cable that comes bundled with the camera to connect the camera to your printer’s USB port.
• The camera does not draw power over the USB cable. Make sure the camera’s battery is sufficiently charged before connecting.
• Make sure that you insert the cable connector into the USB/AV port until you feel it click securely into place. Failure to insert the connector fully can result in poor communication or malfunction.
• Note that even while the connector is fully inserted, you still will be able to see the metal part of the connector as shown in the illustration.
• When connecting the USB cable to a USB port, make sure you align the connector correctly with the port.
Making sure that the 6 mark on the camera is aligned with the 4 mark of the USB cable connector, connect the cable to the camera.
USB port
USB/AV port
USB cable
Large connector
USB
Small connector
72
Printing
. To print
1. Turn on the printer and load paper.
2. Turn on the camera.
This will display the print menu screen.
3. Use [8] and [2] to select “Paper Size”, and
then press [6].
4. Use [8] and [2] to select a paper size and
then press [SET].
• The following are the available paper sizes.
x
5", 5"x7", 4"x6", A4, 8.5"x11", By Printer
3.5"
• Selecting “By Printer” prints using a paper size selected on the printer.
• See the documentation that comes with your printer for information about paper settings.
5. Use [8] and [2] to specify the print option you want.
1 Image : Prints one image. Select and then press [SET]. Next, use [4] and
DPOF Printing :Prints multiple images. Select and then press [SET]. With this
• To toggle date stamping on and off, press [BS]. The date stamp will be printed when “On” is indicated on the monitor screen.
[6] to select the image you want to print.
option, images will be printed in accordance with DPOF settings (page 74).
6. Use [8] and [2] to select “Print” and then
press [SET].
Printing will start and the message “Busy... Please wait...” will appear on the monitor screen. The message will disappear after a short while, even though printing is still being performed. Pressing any camera button will cause the printing status to re-appear. The print menu screen will re­appear when printing is complete.
• If you selected “1 Image”, you can repeat the procedure from step 5, if you want.
7. After printing is complete, turn off the camera and disconnect the USB
cable from the printer and camera.
73
Printing

Using DPOF to Specify Images to be Printed and the Number of Copies

. Digital Print Order Format (DPOF)
DPOF is a standard that allows you to include image type, number of copy, and time stamp on/off information on the memory card with the images. After configuring settings, you can use the memory card to print on a home printer that supports DPOF or take the memory card to a professional print service.
• Whether or not you will be able to use DPOF settings for printing depends on the printer you are using.
• Some professional print services may not support DPOF.
. Configuring DPOF Settings Individually for Each Image
Procedure
[p] (PLAY) * Snapshot Screen * [MENU] * PLAY Tab * DPOF Printing * Select images
1. Use [4] and [6] to scroll through the files until the image you want to
print is displayed.
2. Use [8] and [2] to specify the number of copies.
You can specify a value up to 99. Specify 00 if you do not want to print the image.
• If you want to include the date in the images, press [BS] so “On” is shown for date stamping.
• Repeat steps 1 and 2 to configure settings for other images, if you want.
3. Press [SET].
74
Printing
. Configuring the Same DPOF Settings for All the Images
Procedure
[p] (PLAY) * Snapshot Screen * [MENU] * PLAY Tab * DPOF Printing * All images
1. Use [8] and [2] to specify the number of copies.
You can specify a value up to 99. Specify 00 if you do not want to print the image.
• If you want to include the date in the images, press [BS] so “On” is shown for date stamping.
2. Press [SET].
DPOF settings are not cleared automatically after printing is complete.
The next DPOF print operation you execute will be performed using the last DPOF settings you configured for the images. To clear DPOF settings, specify “00” for the number of copies of all images.
Tell your print service about your DPOF settings!
If you take a memory card to a professional print service, be sure to tell them that it includes DPOF settings for the images to be printed and the number of copies. If you don’t, the print service may print all the images without regard to your DPOF settings, or they may ignore your date stamp setting.
75
Printing
. Date Stamping
You can use one of the following three methods to include the recording date in the printout of an image.
Configure DPOF settings (page 74). You can turn date stamping on and off each time you print. You can configure settings so some images include the date stamp and some don’t.
Configuring camera settings
Configure the Camera’s Time Stamp setting (page 99).
• The camera’s Time Stamp setting imprints the date into a snapshot when you shoot it, so the date is always included when you print. It cannot be deleted.
• Do not turn on DPOF date stamping for an image that includes a date stamped with the camera’s Time Stamp function. Doing so can cause the two stamps to be overprinted.
Configuring computer settings
Professional print service
You can stamp dates into images using the bundled Photo Loader with HOT ALBUM (page 78) software (Windows only).
Request date stamping when ordering prints from a professional print service.
. Standards Supported by the Camera
• PictBridge This is a standard of the Camera and Imaging Products Association (CIPA).
•Exif Print Printing on a printer that supports Exif Print (Exif 2.2) uses information about shooting conditions recorded with the image to enhance printed image quality. Contact your printer manufacturer for information about models that support Exif Print, printer upgrades, etc.
76
Printing

Using the Camera with a Computer

Things you can do using a computer...

You can perform the operations described below while the camera is connected to a computer.
Save images to a computer and view them there
Transfer images stored on your computer to camera memory
Playback and edit movies
• Save images and view them manually (USB connection) (pages 80, 89).
• Save images and view them automatically (Photo Loader with HOT ALBUM*) (page 83). Images will be grouped by recording date and displayed in a calendar format.
In addition to images, you also can transfer screen shot images from your computer to the camera (Photo Transport*) (page 86).
• You can play back movies using DirectX 9.0c (page 84).
• To edit movies, use commercially available software as required.
* Windows only
The procedures you need to perform when using the camera with your computer and when using the bundled software are different for Windows and the Macintosh.
• Windows users should refer to “Using the Camera with a Windows Computer” on page 78.
• Macintosh users should refer to “Using the Camera with a Macintosh” on page
89.
77
Using the Camera with a Computer

Using the Camera with a Windows Computer

Install the required software in accordance with the version of Windows you are running and what you want to do.
When you want to do this:
Operating System Version
Install this software:
Save images to a computer and view them there
Vista / XP / 2000 Installation not required. 80
manually
Save images to a computer automatically/ Manage images
Vista / XP / 2000
Photo Loader with HOT ALBUM
3.1 DirectX 9.0c (When DirectX 9.0 or
higher is not already installed on the computer.)
DirectX 9.0c
Windows 2000 Users of the above operating systems also need to install DirectX 9.0c if DirectX 9.0 or greater is not already installed on your system (page 83).
Play movies Vista / XP / 2000
• Windows Media Player is not included on the CD-ROM that comes bundled with the camera, but it is included with Windows. Use the Windows Media Player application that is installed with Windows for playback.
Edit movies Vista / XP / 2000–• Use commercial software as
required.
Upload movie files to YouTube
Transfer images to the camera
View the User’s Guide
Vista / XP (SP2) / 2000 (SP4)
YouTube Uploader for CASIO 84
Vista / XP / 2000 Photo Transport 1.0 86
Vista / XP (SP2) / 2000 (SP4)
Adobe Reader 8
(Not required if already installed.)
See page:
83
83
88
78
Using the Camera with a Computer
. Computer System Requirements for Bundled Software
Computer system requirements are different for each of the applications. See the “Read me” file that comes with each application for details. Information about computer system requirements also can be found under “Computer System Requirements for Bundled Software” on page 120 of this manual.
. Precautions for Windows Users
• Photo Loader with HOT ALBUM, YouTube Uploader for CASIO, and Photo Transport will not run under 64-bit versions of Windows Vista.
• Except for DirectX and Adobe Reader, the bundled software requires Administrator privileges to run.
• Operation on a self-made computer is not supported.
• Operation may not be possible under certain computer environments.
• Photo Loader with HOT ALBUM provides a function for migrating image data previously saved with Photo Loader, which means you still will have access to your existing image archives.
79
Using the Camera with a Computer

Viewing and Storing Images on a Computer

You can connect the camera to your computer in order to view and store images (snapshot and movie files).
. To connect the camera to your computer and save files
1. Turn on the camera and press [MENU].
2. On the “Set Up” tab, select “USB” and then press [6].
3. Use [8] and [2] to select “Mass Storage”, and then press [SET].
4. Turn off the camera and
then use the USB cable
USB port
USB cable
that comes with the camera to connect it to
Large connector
your computer.
• The camera does not draw power over the USB cable. Make sure the camera’s battery is sufficiently charged before connecting.
• Make sure that you insert the cable connector into the USB/AV port until you feel it click securely into place. Failure to insert the connector fully can result in poor communication or malfunction.
• Note that even while the connector is fully inserted, you still will be able to see the metal part of the connector as shown in the illustration.
• When connecting the USB cable to a USB port, make sure you align the connector correctly with the port.
• Your computer may not be able to recognize the camera if you connect via a USB hub. Always connect directly to the computer’s USB port.
USB/AV port
Making sure that the 6 mark on the camera is aligned with the 4 mark of the USB cable connector, connect the cable to the camera.
Small connector
80
Using the Camera with a Computer
5. Turn on the camera.
6. Copy images to your computer.
Windows XP
Select “Open folder to view files” and then click “OK”.
1
Drag the “DCIM” folder to your Windows desktop to copy it.
2
Windows Vista
Select “Open folder to view files”.
1
Drag the “DCIM” folder to your Windows desktop to copy it.
2
Windows 2000
Double-click “My Computer”.
1
Double-click “Removable Disk”.
2
Drag the “DCIM” folder to your Windows desktop to copy it.
3
7. After you finish copying images, disconnect the camera from the
computer.
Windows Vista, Windows XP
On the camera, press [ON/OFF] to turn off the camera. After making sure that the back lamp is unlit, disconnect the camera from the computer.
Windows 2000
Click card services in the task tray on your computer screen, and disable the drive number assigned to the camera. Next, after making sure that the back lamp is unlit, press the camera’s [ON/OFF] button to turn off the camera and disconnect the camera from your computer.
81
Using the Camera with a Computer
. To view images you copied to your computer
1. Double-click the copied “DCIM” folder to open it.
2. Double-click the folder that contains the images you want to view.
3. Double-click the image file you want to view.
• For information about file names, see “Memory Folder Structure” on page 94.
• An image that was rotated on the camera will be displayed on your computer screen in its original (unrotated) orientation.
IMPORTANT!
• Never use your computer to modify, delete, move, or rename any image files that are in the camera’s built-in memory or on its memory card. Doing so can cause problems with the camera’s image management data, which will make it impossible to play back images on the camera and can drastically alter remaining memory capacity. Whenever you want to modify, delete, move, or rename an image, do so only on images that are stored on your computer.
• Never unplug the USB cable, or operate the camera while viewing or storing images. Doing so can cause data to become corrupted.
82
Using the Camera with a Computer

Save images to a computer automatically/Manage images

Installing Photo Loader with HOT ALBUM on your computer makes it possible to transfer images from the camera to your computer automatically.
. To install Photo Loader with HOT ALBUM
1. Start up your computer, and place the bundled CD-ROM into its CD-
ROM drive.
Normally, this should cause the menu screen to appear automatically. If your computer does not display the menu screen automatically, navigate to the CD­ROM on your computer and then double-click the “AutoMenu.exe” file.
2. Click “Photo Loader with HOT ALBUM 3.1” to select it and then click
“Read me.”
The “Read me” file contains important information about installation, including installation conditions and computer system requirements.
3. Click “Install” for Photo Loader with HOT ALBUM.
4. Follow the instructions that appear on the display to complete
installation.
Checking Your Computer’s DirectX Version
In order to manage images using Photo Loader with HOT ALBUM, your computer also needs to have Microsoft DirectX 9.0 or higher installed. Use the following procedure to check your computer’s DirectX version.
1. Click the following items on your computer to display System Tools:
Start * All Programs * Accessories * System Tools.
2. On the System Tools “Tools” menu, select “DirectX Diagnostic Tool”.
On the “System” tab, check to make sure that the “DirectX Version” is 9.0 or higher.
3. Click “Exit” to exit the DirectX Diagnostic Tool.
• If your computer does not have Microsoft DirectX 9.0 or higher installed, install Microsoft DirectX 9.0c from the bundled CD-ROM.
83
Using the Camera with a Computer

Playing Movies

Windows Media Player, which is already installed on most computers, can be used for movie playback. To play back a movie, first copy the movie to your computer and then double-click the movie file.
. Movie Playback Precautions
• Be sure to move the movie data to the hard disk of your computer before trying to play it. Proper movie playback may not be possible for data accessed over a network, from a memory card, etc.
• Proper movie playback may not be possible on some computers. If you experience problems, try the following. – Try recording movies with a quality setting of “Normal” or “LP”. – Try upgrading Windows Media Player to the latest version. – Quit any other applications you have running, and stop resident applications.
Even if proper playback is not possible on the computer, you can use the AV cable that comes bundled with the camera to connect to the video input terminal a TV or computer and play back movies that way.

Uploading Movie Files to YouTube

Installing YouTube Uploader for CASIO from the CD-ROM that comes with your camera simplifies uploading of movie files you recorded with the “For YouTube” BEST SHOT scene to YouTube.
. What is YouTube?
YouTube is a movie sharing site managed by YouTube, LLC where you can upload movies and view movies uploaded by others.
. To install YouTube Uploader for CASIO
1. On the CD-ROM menu screen (page 83), select “YouTube Uploader for
CASIO”.
2. After reading the information about installation conditions and system
requirements for installation in the “Read me” file, install YouTube Uploader for CASIO.
84
Using the Camera with a Computer
. To upload a movie file to YouTube
• Before you can use YouTube Uploader for CASIO, you need to go to the YouTube website (http://www.youtube.com/) and register as a user there.
• Do not upload any video that is copyrighted (including neighboring copyrights) unless you yourself own the copyright or you have obtained the permission of the applicable copyright holder(s).
• The maximum file size for each upload is 100 MB.
1. Record the movie you want to upload using the “For YouTube” BEST
SHOT movie scene.
2. If it isn’t already, connect your computer to the Internet.
3. Connect the camera to your computer (page 80).
4. Turn on the camera.
YouTube Uploader for CASIO will start up automatically.
• If this is the first time you are using the application, configure the YouTube user ID and network environment settings, and then click the [OK] button.
5. The left side of the display will have an area for inputting a title,
category, and other information required for uploading to YouTube. Enter the required information.
6. The right side of the display shows a list of movie files in camera
memory. Select the check box next to the movie file you want to upload.
7. When everything is ready, click the [Upload] button.
This will upload the movie file(s) to YouTube.
• After uploading is complete, click the [Exit] button to exit the application.
85
Using the Camera with a Computer

Transferring Images from Your Computer to Camera Memory

If you want to transfer images from your computer to the camera, install Photo Transport on your computer from the CD-ROM that comes with the camera.
. To install Photo Transport
1. On the CD-ROM menu screen (page 83), select “Photo Transport”.
2. After reading the information about installation conditions and system
requirements for installation in the “Read me” file, install Photo Transport.
. To transfer images to the camera
1. Connect the camera to your computer (page 80).
2. On your computer, click the following: Start * All Programs *
Casio * Photo Transport.
This starts up Photo Transport.
3. Drag the file(s) you want to transfer to the [Transfer] button.
4. Follow the instructions that appear on the display to complete the
transfer.
• The details of the instructions that appear on the display and the transferred images will depend on your Photo Transport setup. For details, click the [Settings] button or [Help] button and check the setup.
Transfer Data
• Only image files with the following extensions can be transferred to the camera: jpg, jpeg, jpe, bmp (bmp images are converted to jpeg image automatically when transferred.)
• Certain types of images may not be able to be transferred.
• You cannot transfer movies to the camera.
B
86
Using the Camera with a Computer
. To transfer computer screen captures to the camera
1. Connect the camera to your computer (page 80).
2. On your computer, click the following: Start * All Programs *
Casio * Photo Transport.
This starts up Photo Transport.
3. Display the screen whose screen capture you want to transfer.
4. Click the [Capture] button.
5. Draw a boundary around the area you want to capture.
Move your mouse pointer to the upper left corner of the area you want to capture and then hold down the mouse button. Keeping the mouse button depressed, drag the pointer down to the lower right corner of the area and then release the mouse button.
6. Follow the instructions that appear on the display.
This will send an image of the area you selected to the camera.
• The transfer operation converts screen captures to JPEG format.
• The instructions that appear on the display and details about the transferred images will depend on your Photo Transport setup. For details, click the [Settings] button or [Help] button and check the setup.
. About settings and help
Click the [Settings] button when you want to change the Photo Transport setup. For help about operation procedures and troubleshooting, click the Photo Transport [Help] button.
87
Using the Camera with a Computer

Viewing User Documentation (PDF Files)

1. Start up your computer, and place the bundled CD-ROM into its CD-
ROM drive.
Normally, this should cause the menu screen to appear automatically. If your computer does not display the menu screen automatically, navigate to the CD­ROM on your computer and then double-click the “AutoMenu.exe” file.
2. On the menu screen, click the “Language” down arrow button and then
select the language you want.
3. Click “Manual” to select it and then click “Digital Camera”.
IMPORTANT!
• You must have Adobe Reader or Adobe Acrobat Reader installed on your computer in order to view the contents of a PDF file. If you do not already have Adobe Reader or Adobe Acrobat Reader installed, install Adobe Reader from the bundled CD-ROM.

User Registration

You can perform user registration over the Internet. To do so, of course, you need to be able to connect to the Internet with your computer.
1. On the CD-ROM menu screen (page 83), click the “Register” button.
• This starts up your Web browser and accesses the user registration website. Follow the instructions that appear on your computer screen to register.
88
Using the Camera with a Computer

Using the Camera with a Macintosh

Install the required software in accordance with what version of the Macintosh OS you are running and what you want to do.
When you want to do this:
Save images to your Macintosh and view them there manually
Save images to your Macintosh automatically/ Manage images
Play movies
Operating System Version
Mac OS 9
Mac OS X
Mac OS 9
Mac OS X
Mac OS 9 / OS X
Install this software:
Installation not required. 89
Use commercially available software.
Use iPhoto, which comes bundled with your operating system.
You can playback with QuickTime, which comes bundled with your operating system.
See
page:
91
92

Connecting the Camera to Your Computer and Saving Files

IMPORTANT!
• The camera does not support operation with Mac OS 8.6 or earlier, or Mac OS X
10.0. Operation is supported with Mac OS 9, X (10.1, 10.2, 10.3, 10.4, 10.5) only. Use the standard USB driver that comes with your supported operating system.
. To connect the camera to your computer and save files
1. Turn on the camera and press [MENU].
2. On the “Set Up” tab, select “USB” and then press [6].
3. Use [8] and [2] to select “Mass Storage”, and then press [SET].
89
Using the Camera with a Computer
4. Turn off the camera and
then use the USB cable
USB port
USB cable
that comes with the camera to connect it to
Large connector
your Macintosh.
• The camera does not draw power over the USB cable. Make sure the camera’s battery is sufficiently charged before connecting.
• Make sure that you insert the cable connector into the USB/AV port until you feel it click securely into place. Failure to insert the connector fully can result in poor communication or malfunction.
• Note that even while the connector is fully inserted, you still will be able to see the metal part of the connector as shown in the illustration.
• When connecting the USB cable to a USB port, make sure you align the connector correctly with the port.
• Your computer may not be able to recognize the camera if you connect via a USB hub. Always connect directly to the computer’s USB port.
USB/AV port
Making sure that the 6 mark on the camera is aligned with the 4 mark of the USB cable connector, connect the cable to the camera.
Small connector
5. Turn on the camera.
The camera’s back lamp will light green at this time. In this mode, your Macintosh recognizes the memory card loaded in the camera (or the camera’s built-in memory if it does not have a memory card loaded) as a drive. The appearance of the drive icon depends on the Mac OS version you are using.
6. Double-click the camera’s drive icon.
7. Drag the “DCIM” folder to the folder to which you want to copy it.
8. After the copy operation is complete, drag the drive icon to Trash.
9. On the camera, press [ON/OFF] to turn off the camera. After making
sure that the green back lamp is unlit, disconnect the camera from the computer.
90
Using the Camera with a Computer
. To view copied images
1. Double-click the camera’s drive icon.
2. Double-click the “DCIM” folder to open it.
3. Double-click the folder that contains the images you want to view.
4. Double-click the image file you want to view.
• For information about file names, see “Memory Folder Structure” on page 94.
• An image that was rotated on the camera will be displayed on your Macintosh screen in its original (unrotated) orientation.
IMPORTANT!
• Never use your computer to modify, delete, move, or rename any image files that are in the camera’s built-in memory or on its memory card. Doing so can cause problems with the camera’s image management data, which will make it impossible to play back images on the camera and can drastically alter remaining memory capacity. Whenever you want to modify, delete, move, or rename an image, do so only on images that are stored on your computer.
• Never unplug the USB cable, or operate the camera while viewing or storing images. Doing so can cause data to become corrupted.

Transferring Images Automatically and Managing Them on Your Macintosh

If you are running Mac OS X, you can use the iPhoto application that comes bundled with the operating system to manage your images. If you are running Mac OS 9, you will need to use commercially available software.
91
Using the Camera with a Computer

Playing a Movie

You can use QuickTime, which comes bundled with your operating system, to play back movies on a Macintosh. To play back a movie, first copy it to your Macintosh and then double-click the movie file.
. Movie Playback Precautions
Proper movie playback may not be possible on some Macintosh models. If you experience problems, try the following.
– Change the movie image quality setting to “Normal” or “LP”. – Upgrade to the latest version of QuickTime. – Shut down other applications that are running.
Even if proper playback is not possible on your Macintosh, you can use the AV cable that comes bundled with the camera to connect to the video input terminal a TV or Macintosh and play back movies that way.
IMPORTANT!
• Be sure to move the movie data to the hard disk of your Macintosh before trying to play it. Proper movie playback may not be possible for data accessed over a network, from a memory card, etc.

Viewing User Documentation (PDF Files)

You must have Adobe Reader or Adobe Acrobat Reader installed on your computer in order to view the contents of a PDF file. If you don’t, go to the Adobe Systems Incorporated website and install Acrobat Reader.
1. On the CD-ROM, open the “Manual” folder.
2. Open the “Digital Camera” folder and then open the folder for the
language whose user’s guide you want to view.
3. Open the file named “camera_xx.pdf”.
• “xx” is the language code (Example: camera_e.pdf is for English.)

User Registration

Internet registration only is supported. Visit the following CASIO website to register: http://world.casio.com/qv/register/
92
Using the Camera with a Computer

Files and Folders

The camera creates a file and saves it each time you shoot a snapshot, record a movie, or perform any other operation that stores data. Files are grouped by storing them in folders. Each file and folder has its own unique name.
• For details about how folders are organized in memory, see “Memory Folder Structure” (page 94).
Name and Maximum Number Allowed Example
File
Each folder can contain up to 9999 files named CIMG0001 through CIMG9999. The extension on the file name depends on the file type.
Folders
Folders are named from 100CASIO to 999CASIO There can be up to 900 folders in memory.
• The BEST SHOT mode (page 42) includes a sample scene that optimizes settings for auction site images. Depending on your camera model, the sample scene is named either “For eBay” or “Auction”. – Images recorded with the eBay scene are
stored in a folder named “100_EBAY”.
– Images recorded with the Auction scene
are stored in a folder named “100_AUCT”.
• BEST SHOT also has a scene named “For YouTube” that optimizes movie settings for recording movies for upload to YouTube. Images recorded with the YouTube scene are stored in a folder named “100YOUTB”.
• You can view folder and file names on your computer. For details about how file names are displayed on the camera’s monitor screen, see page 123.
• The total number of folders and files allowed depends on the image size and quality, and capacity of the memory card being used for storage.
26th file name:
CIMG0026.JPG
Extension
Serial number (4 digits)
100th folder name:
100CASIO
Serial number (3 digits)
93
Using the Camera with a Computer

Memory Card Data

The camera stores images you shoot in accordance with the Design Rule for Camera File System (DCF).
. About DCF
DCF is a standard that makes it possible to view and print images recorded on one manufacturer’s camera on DCF-compliant devices produced by other manufacturers. You can transfer DCF-compliant images recorded with another camera to this camera and view them on this camera’s monitor screen.
. Memory Folder Structure
DCIM
100CASIO CIMG0001.JPG CIMG0002.AVI CIMG0003.WAV CIMG0004.JPG CIMG0004.WAV
101CASIO 102CASIO
MISC
AUTPRINT.MRK
* Other folders are created when the following BEST SHOT scenes are used for
recording: “For eBay” or “Auction” (scene name depends on camera model), or “For YouTube”. The following shows the name of the folder created for each scene.
eBay scene: 100_EBAY
Auction scene: 100_AUCT
YouTube scene: 100YOUTB
DCIM Folder Recording Folder
*
Image File Movie File Audio File Audio Snapshot Image File Audio Snapshot Audio File
Recording Folder
*
Recording Folder
*
DPOF File Folder DPOF File
94
Using the Camera with a Computer
. Supported Image Files
• Image files shot with this camera
• DCF-compliant image files
This camera may not be able to display an image, even if it is DCF-compliant. When displaying an image recorded on another camera, it may take a long time for the image to appear on this camera’s monitor screen.
. Built-in Memory and Memory Card Data Handling Precautions
• Whenever copying memory contents to your computer, you should copy the DCIM folder and all of its contents. A good way to keep track of multiple DCIM copies of the DCIM folders it to change its name to a date or something similar after you copy it to your computer. If you later decided to return the folder to the camera, however, be sure to change its name back to DCIM. The camera is designed to recognize only a root file with the name DCIM. Note the camera also will not be able to recognize the folders inside the DCIM folder unless they have the names they originally had when you copied them from the camera to your computer.
• Folders and files must be stored in accordance with the “Memory Folder Structure” shown on page 94 in order for the camera to be able to recognize them correctly.
• You also can use a PC card adapter or a memory card reader/writer to access camera files directly from the camera’s memory card.
95
Using the Camera with a Computer

Other Settings (Set Up)

This section explains menu items that you can use to configure settings and perform other operations in both the REC mode and PLAY mode.
For information about menu operations, see page 46.
Selecting a REC Mode Screen Layout (R Panel)
Procedure
[MENU] * Set Up Tab * R Panel
The REC mode screen layout settings let you select the layout of icons.
Displays the Control Panel. The Control Panel makes it quick and easy to change certain camera settings.
On
Turns off Control Panel display. This setting helps to view more of the image when the 16:9 aspect ratio is selected. Certain camera settings
Off
are indicated by icons on the image.
• All screen shots in this manual show what appears when the Control Panel is turned on.
96
Other Settings (Set Up)
Selecting a PLAY Mode Screen Layout (P Display)
Procedure
[MENU] * Set Up Tab * P Display
The PLAY mode screen layout settings let you select how display images are shown on the monitor screen.
With this setting, the display image is the maximum possible size that allows the entire image to be displayed horizontally. With some
Wide
aspect ratios, the top and bottom of the image will be cut off.
100% of the display image is always visible. With some aspect ratios, black bands may appear above and below, or to the left and right
4:3
of the image.

Configuring Camera Sound Settings (Sounds)

Procedure
[MENU] * Set Up Tab * Sounds
Startup
Half Shutter
Shutter
Operation
Operation ( )
Play ( )
• Setting a volume level of 0 mutes output.
Specifies the startup sound Sound 1 - 5: Built-in sounds (1 through 5) Off: Sound off
Specifies the sound volume. This setting is also used as the audio level during video output (page 63).
Specifies the volume of movie and Audio Snapshot audio output. This volume setting is not used during video output (from the USB/AV port).
97
Other Settings (Set Up)

Specifying the File Name Serial Number Generation Rule (File No.)

Procedure
[MENU] * Set Up Tab * File No.
Use the following procedure to specify the rule that governs generation of the serial number used in file names (page 93).
Tells the camera to remember the last used file number. A new file will be named using the next sequential number, even if files are deleted or
Continue
Reset
if a blank memory card is loaded. If a memory card is loaded and that card already has files stored on it and the largest sequential number in the existing file names is greater than the largest sequential number remembered by the camera, numbering of new files will start from the largest sequential number in the existing file names plus 1.
Restarts the serial number from 0001 whenever all files are deleted or when the memory card is replaced with a blank one. If a memory card is loaded and that card already has files stored on it, numbering of new files will start from the largest sequential number in the existing file names number plus 1.
98
Other Settings (Set Up)

Configuring World Time Settings (World Time)

Procedure
[MENU] * Set Up Tab * World Time
You can use the World Time screen to view the current time in a zone that is different from your Home City when you go on a trip, etc. World Time displays the current time in 162 cities in 32 time zones around the globe.
1. Use [8] and [2] to select “World” and then press [6].
• To change the geographic area and city for the time where you normally use the camera, select “Home”.
2. Use [8] and [2] to select “City” and then press [6].
• To change the “World” setting to summer time, use [8] and [2] to select “DST” and then select “On”. Summer time is used in some geographical areas to advance the current time setting by one hour during the summer months.
3. Use [8], [2], [4], and [6] to select the geographic area you want and
then press [SET].
4. Use [8] and [2] to select the city you want and then press [SET].
5. Press [SET].

Time Stamping Snapshots (Timestamp)

Procedure
[MENU] * Set Up Tab * Timestamp
You can configure the camera to stamp the recording date only, or date and time in the lower right corner of each snapshot.
• Once date and time information is stamped into a snapshot, it cannot be edited or deleted.
Example: December 19, 2009, 1:25 p.m.
Date 2009/12/19
Date&Time 2009/12/19 1:25pm
Off No stamping of date and/or time
• Even if you do not stamp the date and/or time with Timestamp, you can do so later using the DPOF function or some printing application (page 76).
• Digital zoom is disabled while date stamping is turned on.
99
Other Settings (Set Up)

Setting the Camera’s Clock (Adjust)

Procedure
[MENU] * Set Up Tab * Adjust
[8] [2] Change the setting at the cursor location
[4] [6] Move the cursor between settings
[BS] Toggles between 12-hour and 24-hour format
When the date and time settings are what you want, press [SET] to apply them.
• You can specify a date from 1980 to 2049.
• Be sure to select your Home City (page 99) before setting the time and date. If you set the time and date while the wrong city is selected for your Home City, the times and dates of all of the World Time cities (page 99) will be wrong.

Specifying the Date Style (Date Style)

Procedure
[MENU] * Set Up Tab * Date Style
You can select from among three different styles for the date. Example: December 19, 2009
YY/MM/DD 09/12/19
DD/MM/YY 19/12/09
MM/DD/YY 12/19/09
• This setting also affects the Control Panel date format as shown below (page 23). YY/MM/DD or MM/DD/YY: MM/DD DD/MM/YY: DD/MM
100
Other Settings (Set Up)
Loading...