• Before using it, be sure to read the precautions contained in this User’s Guide.
• Keep the User’s Guide in a safe place for future reference.
• For the most up-to-date information about this product, visit the official EXILIM
Website at http://www.exilim.com/
Accessories
As you unpack your camera, check to make sure that all accessories shown below
are included. If anything is missing, contact your original retailer.
Rechargeable lithium ion
battery (NP-150)
USB-AC adaptor
(AD-C54UC)
Micro USB cable
2
Read this first!
• The contents of this manual are subject to change without notice.
• The contents of this manual have been checked at each step of the production
process. Feel free to contact us if you notice anything that is questionable,
erroneous, etc.
• Any copying of the contents of this User’s Guide, either in part or its entirety, is
forbidden. Except for your own personal use, any other use of the contents of this
manual without the permission of CASIO COMPUTER CO., LTD. is forbidden
under copyright laws.
• CASIO COMPUTER CO., LTD. shall not be held liable for any damages or lost
profits suffered by you or any third party due to the use or malfunction of this
product.
• CASIO COMPUTER CO., LTD. shall not be held liable for any damages, lost
profits, or claims by third parties arising out of the use of EXILIM Connect.
• CASIO COMPUTER CO., LTD. shall not be held liable for any damages or lost
profits caused by loss of memory contents due to malfunction, repair, or any other
reason.
• Note that the example screens and product illustrations shown in this User’s Guide
may differ somewhat from the screens and configuration of the actual camera.
LCD Panel
The liquid crystal panel of the monitor screen uses high-precision technology that
provides a pixel yield in excess of 99.99%. This means that some very small number
of pixels may not light or may remain lit at all times. This is due to the characteristics
of the liquid crystal panel, and does not indicate malfunction.
Take test shots
Before shooting your final image, shoot a test shot to ensure that the camera is
recording correctly.
To attach the strap to the camera
(commercially available or separately available)
Attach strap here.
The numbers in parentheses indicate the pages where each item is explained.
• Above illustration shows the camera’s cover removed (page 19).
8
Monitor Screen Contents and How to Change Them
PLAY mode icon (page 31)
“” (Show Icons) icon
Make-up icon (page 41)
White Balance (page 68)
Focus mode (page 70)
Digital zoom (page 46)
Timestamp (page 112)
Self-timer mode (page 65)
Snapshot image size (page 66)
Movie quality (pages 50, 67)
Battery level indicator (page 26)
LED light (page 48)
Operation assigned to selfie pad
(pages 19, 63)
Remaining movie memory capacity
(page 149)
Remaining snapshot memory capacity
(page 148)
“ ” Movie icon (pages 34, 51)
Date/Time (pages 26, 114)
Brightness (page 67)
ISO sensitivity (page 69)
Bluetooth Smart communication
status (page 90)
Auto Send (page 97)
Wireless LAN communication status
(page 90)/Airplane mode (page 96)
Menu icon (page 62)
Recording mode icon (page 40)
Wireless mode icon (page 89)
Mirror mode icon (page 45)
bq
bs
bt
1
3
cq cp co cn
2
br
cl
cm
ck
9
7
8
5
4
bk
bl
bn bmbobp
6
The monitor screen uses various indicators, icons, and values to keep you informed
of the camera’s status.
• The sample screens in this section are intended to show you the locations of all the
indicators and figures that can appear on the monitor screen in various modes.
They do not represent screens that actually appear on the camera.
. Snapshot Recording
9
. Movie Recording
NOTE
42
13
5
Protect indicator (page 84)
“” (Show Icons) icon
Folder name-file name (page 108)
Snapshot image size (page 66)
Operation assigned to selfie pad
(pages 19, 79)
Battery level indicator (page 26)
Date/time (pages 26, 114)
Image menu icon (p
age 75)
Shutter speed
Make-up (page 41)
Brightness (page 67)
ISO sensitivity (page 69)
Bluetooth Smart communication
status (page 90)
Auto Send (page 97)
White Balance (page 68)
Wireless LAN communication status
(page 90)/Airplane mode (page 96)
Menu icon (page 78)
Delete icon (page 36)
Wireless mode icon (pages 89, 95)
Promotion Movie icon (page 76)
REC mode icon (page 31)
• If you do not perform any operation for about three seconds during snapshot
recording or movie recording, icons will become transparent.
. Snapshot Viewing
cl ck bt bs br
bq
bp
bo
bn
bm
bl
bk
9
8
4213
Movie quality (
Recording time switch icon (page 51)
Movie remaining time icon (page 51)
Remaining movie memory capacity/
Movie recording time (pages 51, 149)
“ ” Movie stop icon (pages 34, 51)
5
6
7
pages 50, 67)
10
NOTE
• The folder name and file name in the upper right corner of the monitor screen has
NOTE
6
5
78
9
4213
the meaning described below (page 108).
Example: 100-0023: 23rd image file in the folder named “100CASIO”.
. Movie Playback
Protect indicator (page 84)
“” (Show Icons) icon
Folder name-file name (page 108)
Repeat playback icon (page 72)
Movie quality (pages 50, 67)
Movie recording time (page 72)
Date/time (pages 26, 114)
Image menu ico
“”
Movie play ico
• If you do not perform any operation for about three seconds during snapshot
viewing or movie playback, icons will become transparent.
n (page 75)
n (page 72)
11
Quick Start Basics
*See page 41 for more information.
*See page 47 for more information.
Selfie Pad
*See page 19 for more information.
*See page 63 for more information.
What you can do with your CASIO camera
Your CASIO camera is packed with a powerful selection of features and functions to
make recording of digital images easier, including the following main functions.
Shooting better looking portraits
Make-up enables adjustment of human skin tone hues
and texture, and softening of facial shadows caused by
harsh sunlight for better looking portraits.
Simple self-portrait shooting
The monitor screen can be rotated so it faces in the
same direction as the camera’s lens, making selfshooting much easier.
Selfie Pad
The camera’s selfie pad enables one-hand operation.
One operation each for the REC Mode and PLAY
Mode can be assigned to the selfie pad.
REC Mode: Selfie Art, shutter release, zoom.
PLAY Mode: screen scrolling, zoom.
Selfie Art
Apply different effects to make self-portraits shot with
the selfie pad better looking and more interesting.
12
Quick Start Basics
Instant Movie
*See page 53 for more information.
*See page 87 for more information.
*See page 44 for more information.
Movie recording can be paused and resumed as
required to create a short movie quickly and easily.
Wireless Connection
Use EXILIM Auto Transfer to transfer images you
shoot with the camera to a smartphone or a social
networking service automatically.
You can also turn your smartphone into a camera
remote controller and send images recorded with your
camera to your smartphone.
Posing Shot
Posing Shot lets you shoot five successive snapshots,
as the camera provides voice guidance for each. This
lets you strike a pose for each individual shot.
13
Quick Start Basics
IMPORTANT!
Changing the Camera Style to Suit Shooting Conditions
225 degrees
You can change the configuration of the camera by opening or closing the frame and
rotating the monitor screen panel to suit shooting conditions.
IMPORTANT!
• Do not apply strong pressure to the surface of the monitor screen. Doing so can
damage it.
• Never touch the lens with your fingers. Finger smudges, dirt, and other foreign
matter on the lens can interfere with proper operation of the camera. Use a blower
or other means to keep the lens and flash window free of dirt and dust, and wipe
gently with a soft, dry cloth.
Opening and Closing the Frame
The camera’s frame can be rotated 225 degrees
as shown in the illustration.
1. With the lens facing towards you, hold
onto the frame.
2. Push the monitor screen panel.
3. Holding the edges of the monitor
screen panel, swing the frame open.
• Do not try to open or close the frame while the monitor screen panel is rotated.
Doing so can cause the frame to come into contact with the monitor screen panel
and cause malfunction.
14
Quick Start Basics
NOTE
Rotating the Monitor Screen
270 degrees counterclockwise
Use the steps below to rotate the monitor screen.
• While holding the monitor screen panel as shown in the illustration, you can rotate
it 270 degrees counterclockwise.
1. Hold the camera as shown in the
illustration.
2. Firmly holding the frame, carefully
rotate the monitor screen panel.
15
Quick Start Basics
Camera Configurations
You can open the frame and rotate the monitor screen for a variety of different styles.
Normal ShootingShooting with the Frame
Shoot with the monitor screen facing the
opposite direction of the lens.
Tabletop ShootingSelf-portrait Shooting
Point the monitor screen and lens in the
same direction and open the frame
about 30 degrees so the camera can
stand up.
Open the frame 90 degrees and hold the
frame. You can also shoot with the
camera upside down, if you like.
Open the frame, point the monitor
screen and lens in the same direction.
16
Quick Start Basics
NOTE
• When shooting hold the camera still. Carefully press the shutter button and take
IMPORTANT!
Microphone
Lens
LED light
care to avoid all movement as the shutter releases and for a few moments after it
releases.
• Take care that your fingers and the strap do not cover
any of the areas indicated in the illustration.
• To protect against accidentally dropping the camera,
attach the wrist strap (commercially available or
separately available) and make sure it is around your
fingers or wrist while you are operating the camera.
• Never swing the camera around by its strap.
• Take care to ensure that your finger is not blocking or
is not too close to the LED light. Fingers can cause
unwanted shadows when shooting.
Using the Touch Panel
The monitor screen of the camera is a touch panel. This means you can perform the
following operations by touching the screen with your fingers.
Touch
Momentarily touching the screen with your finger.
Touch the screen to select an icon or menu item, and
to configure settings.
You can zoom in and zoom out on a displayed image
by tapping it twice in succession.
Touch-and-hold
Holding your finger against the screen.
Touch and hold the screen to perform continual
frame-by-frame playback of a movie.
17
Quick Start Basics
Drag
IMPORTANT!
NOTE
Holding your finger against the screen as you drag it
up, down, left, or right.
Use drag to move a screen image to a different
location, and to scroll between images.
Spread
Holding your thumb and forefinger against the screen
as you spread them out.
Use spread to enlarge the screen image.
Squeeze
Holding your thumb and forefinger against the screen
as you bring them together.
Use squeeze to reduce the size of the screen image.
• Never use a pointed or hard object to perform screen operations. Doing so can
damage the screen.
• The camera will have a hard time interpreting a screen operation made using your
fingernails. Use the fleshy pad of your finger.
• Applying a commercially available LCD protective sheet will reduce the operation
sensitivity of the monitor screen.
18
Quick Start Basics
NOTE
Using the Selfie Pad
Selfie pad
2
3
1
[OPEN] button
You can use the selfie pad to perform various
functions while shooting a self-portrait.
Double-tap
Double-tapping the selfie pad displays an icon
“μ” to let you know that selfie pad operation
is enabled.
Double-tapping the selfie pad again disables
selfie pad operation. Note, however, that if the
Selfie Art function is assigned to the selfie pad,
you will need to disable it using either one of
the following operations: double-tap the selfie
pad and then touch “EXIT”, or double-tap the
selfie pad, use the selfie pad to select “EXIT”,
and then double-tap the selfie pad again.
Slide
Slide your finger up or down along the selfie pad.
The function assigned to the selfie pad will operate.
• Use the menu screen’s “Selfie Pad” item (pages 63, 79) to assign an operation to
the selfie pad.
First, charge the battery prior to use.
Note that the battery of a newly purchased camera is not charged. Perform the steps
below to load the battery into the camera and charge it.
• Your camera requires a special CASIO rechargeable lithium ion battery (NP-150)
for power. Never try to use any other type of battery.
Loading the Battery
1. Open the frame (page 14).
2. Open the cover.
While depressing the [OPEN] button, slide
the cover in the direction of arrow
nearby illustration.
in the
19
Quick Start Basics
3. Load the battery.
IMPORTANT!
CASIO logo
Battery
OK
NG
2
1
2mm
Lens unit
With the CASIO logo on the battery
upwards, load the battery into the
camera as shown in the illustration.
4. Close the cover.
• Positioning the cover about two millimeters from
the lens unit, keep it parallel with the camera as
you slide it in the direction of arrow
arrow
To replace the battery
to secure it in place.
and then
1. Press [p] (Power) to turn off the camera
and then open the battery cover.
2. Remove the current battery and load a new
one.
As shown in the illustration, pull up the edge of
the battery to remove it.
3. Close the battery cover.
• The operation lamp (page 8) will flash green for some time after you press [p]
(Power) to turn off the camera. Never remove the battery while the operation lamp
is flashing green. Doing so can result in corruption or loss of data in camera
memory.
20
Quick Start Basics
Charge the Battery
3
2
1
USB-AC adaptor
u mark of the small (micro
USB) connector facing the side
opposite that of the monitor
screen.
[USB] port
Micro USB cable
(included with camera)
You can use either of the two following methods to charge the battery. Before
charging the battery, use the procedure under “Opening and Closing the Frame”
(page 14) to open the frame.
• USB-AC adaptor
• USB connection to a computer (Using the included micro USB cable.)
. To charge with the USB-AC adaptor
The adaptor lets you charge the battery while it is loaded in the camera.
While the camera is turned off, connect in the sequence shown below.
Charging time: Approximately 2 hours 20 minutes
• When disconnecting the USB-AC adaptor from the camera, be sure to disconnect
from the camera first.
21
Quick Start Basics
IMPORTANT!
Operation lamp
• A battery that has not been used for a long time and/or ambient temperature can
cause charging to take longer than normal. These conditions may also cause the
operation lamp to flash red. If this happens, refer to page 138.
•Pressing [p] (Power) while the USB-AC adaptor is connected to the camera will
turn on the camera with power being supplied by the battery. Because of this,
charging will stop.
• The USB-AC adaptor will become warm during charging. This is normal and does
not indicate malfunction.
• The shape of the power plug depends on each country or geographic area.
Operation Lamp Operation
Lamp StatusDescription
Lit RedCharging
Abnormal ambient temperature, USB-AC
Flashing Red
adaptor problem, or battery problem (page
138), or charging terminated by the timer
OffCharging complete
22
Quick Start Basics
USB Cable Connection Precautions
Make sure that the u mark side of the
USB cable connector and the opposite side
of the monitor screen are facing in the same
direction.
The opposite side of the
monitor screen
The operation lamp always initially light after charging starts. Even if the battery is
already fully charged, the lamp will light momentarily.
If the lamp does not light, check the orientation of the USB cable connector.
• When connecting the USB cable to the camera, make sure that the cable
connector and monitor screen panel are oriented correctly as shown in the
illustration below.
• Make sure that you insert the cable connector into the USB port until you feel it
click securely into place. Failure to insert the connector fully can result in poor
communication or malfunction.
• Note that even while the connector is fully inserted, you
still will be able to see the metal part of the connector as
shown in the illustration.
23
Quick Start Basics
. To charge using a USB connection to a computer
IMPORTANT!
USB
2
1
Micro USB cable
(included with camera)
u mark of the small (micro USB) connector facing the side
opposite that of the monitor screen.
[USB] port
USB port
Computer
(power turned on)
USB connection lets you charge the battery while it is loaded in the camera.
While the camera is turned off, connect in the sequence shown below (
• If the camera is on, press [p] (Power) to turn it off before connecting it to your
computer.
Charging time: Approximately 2 hours 50 minutes
• The first time you connect the camera to your computer with the USB cable, an
error message may appear on your computer. If this happens, disconnect and then
reconnect the USB cable.
• A battery that has not been used for a long time, certain types of computers, and
connection conditions can cause charging to take longer than normal. These
conditions may also cause the operation lamp to flash red. If this happens, refer to
page 138.
• For faster charging, use of the supplied USB-AC adaptor is recommended.
• You cannot use the camera to shoot images while it is being charged over a
computer USB connection. If you want to shoot with the camera, disconnect the
USB cable.
• If you turn on the camera while charging over a USB connection to a computer is in
progress, the camera will establish a USB connection with the computer. Though
charging normally should continue at this time, certain types of computers or
connection environments may stop charging if supply power is low. This will be
indicated by the camera’s operation lamp lighting green.
• Charging is not performed while the connected computer is in the hibernate mode.
,
).
24
Quick Start Basics
Operation Lamp Operation
Operation lamp
Lamp StatusDescription
Lit Red,
(Lit/Flashing Amber)
Charging
Abnormal ambient temperature,
Flashing Red
charging taking abnormally long, or
battery problem (page 138)
Off, (Lit Green)Charging complete
• The information in parentheses in the above table shows the lamp status while the
camera is turned on during charging.
Other Charging Precautions
• With the two charging methods described above, you can charge the camera’s
battery (NP-150) without removing it from the camera. Never use any other type of
charger device. Attempting to use a different charger can result in unexpected
accident.
• This model can be charged only via from USB 2.0 specification USB port only.
• USB charging devices and power supply devices are subject to fixed standards.
Use of an inferior device or a device that is not up to standard can cause
malfunction and/or failure of your camera.
• Operation is not guaranteed in the case of a computer built or modified by you.
Even in the case of a commercially available computer, certain USB port
specifications may make it impossible to charge via the USB cable.
• A battery that is still warm immediately after normal use may not charge fully. Give
the battery time to cool before charging it.
• A battery discharges slightly even when it is not loaded in the camera. Because of
this, it is recommended that you charge the battery immediately before you need to
use it.
• Charging the camera’s battery may cause interference with TV and radio reception.
If this happens, plug the USB-AC adaptor into an outlet that is further away from
the TV or radio.
• Actual charging time depends on current battery capacity and charging conditions.
• Do not use the USB-AC adaptor with any other device.
• Use only the USB-AC adaptor and USB cable specified in this manual for charging.
Use of any other type of devices may result in improper charging.
25
Quick Start Basics
Checking the Current Battery Level
As battery power is consumed, a battery indicator on the monitor screen indicates its
current level as shown below.
Remaining PowerHighLow
Battery Indicator***
Indicator ColorWhite* White*Red*Red
indicates battery power is low. Charge the battery as soon as possible.
Recording is not possible when is indicated. Charge the battery immediately.
• The level shown by the battery indicator may change when you switch between the
REC mode and PLAY mode.
• Leaving the camera for about 20 days with no power supplied while the battery is
dead will cause its date and time settings to be cleared. A message telling you to
configure time and date settings will appear the next time you turn on the camera
after restoring power. When this happens, configure date and time settings (page
114).
• See page 152 for information about battery life and number of shots.
Configuring Basic Settings the First Time You Turn On the
Camera
The first time you turn on the camera, a screen appears for configuring the display
language, date, and time settings. Failure to set the date and time correctly will cause
the wrong date and time data to be recorded with images.
IMPORTANT!
• A screen for language selection will not appear in step 2 of the procedure below if
you purchased a camera intended for the Japanese market. To change the display
language from Japanese in this case, use the procedure under “Specifying the
Display Language (Language)” (page 115). Note that a version of this manual in
the language you select may not be included with a camera intended for the
Japanese market.
• Camera models sold in certain geographic areas may not support display language
selection.
26
Quick Start Basics
1. Press [p] (Power) to turn on the camera.
NOTE
[p] (Power)
12/24 hour switch
icon
2. Drag (page 18) upwards and downwards until
you find the language you want, and then touch
to select it.
3. Touch the date display format you want.
Example: July 10, 2016
YY/MM/DD
DD/MM/YY
MM/DD/YY
* 16/7/10
* 10/7/16
* 7/10/16
4. Touch the value you want to change (year, month,
day, hour, minute).
5. Touch “ ”, “ ” to change the currently selected
value.
• Touching and holding “ ”, “ ” will change the setting
at high speed.
• To switch between 12-hour and 24-hour format, touch
the 12/24 hour switch icon.
6. When the date and time settings are the way you
want, touch “OK”.
7. Touch “Auto” or “Premium Auto Pro” to select the default auto
recording mode you want.
8. Touch “Apply”.
• You will be able to change this setting later, if you want. See page 32 for
details.
If you make a mistake configuring display language, date, or time settings with the
above procedure, refer to the following pages for information about how to correct
the settings.
– Display language: Page 115
– Date and time: Page 114
• Each country controls its local time offset and the use of summer time, and so they
are subject to change.
27
Quick Start Basics
Preparing a Memory Card
*
Though the camera has built-in memory that can be used to store images and
movies, you probably will want to purchase a commercially available memory card for
greater capacity. The camera does not come with a memory card. Images recorded
while a memory card is loaded are saved to the memory card. When no memory card
is loaded, images are saved to built-in memory.
• For information about memory card capacities, see page 148.
• The above are supported memory card types as of August
2015.
• This camera supports use of microSD memory cards of the following types and
capacities: microSD memory cards up to 2GB; microSDHC memory cards greater
than 2GB, up to 32GB; microSDXC memory cards greater than 32GB, up to 2TB.
Note that the ability to use any particular card with this camera, even if it satisfies
the above capacity and type requirements, is not guaranteed.
Warning!
0 Memory cards are small and present a risk of accidentally being swallowed
by infants and young children. Keep memory cards out of the reach of
infants and young children. If a memory card is ever swallowed accidentally,
contact a physician immediately.
+
. Memory Card Handling Precautions
Certain types of memory cards can slow down processing speeds. In particular, highquality movies may not be able to be stored correctly. A slow memory card can take
too much time to record data and result in breaks in the image and/or audio during
playback. When this happens the movie icon will turn yellow on the monitor screen.
28
Quick Start Basics
IMPORTANT!
To load a memory card
[OPEN] button
Front
FrontBack
2
1
2mm
Lens unit
1. Press [p] (Power) to turn off the
camera and then open the frame
(page 14).
2. While holding down [OPEN], slide
the cover in the direction of arrow
in the nearby illustration to
remove it.
3. Load a memory card.
Positioning the memory card as shown in
the nearby illustration insert it into the
camera’s memory card slot and press
until you hear it click into place.
4. Close the cover.
• Positioning the cover about two millimeters from
the lens unit, keep it parallel with the camera as
you slide it in the direction of arrow
arrow
to secure it in place.
and then
2
3
1
• Never insert anything besides a supported memory card (page 28) into the memory
card slot.
• Should water or any foreign object ever get into the card slot, immediately turn off
the camera, and contact your retailer or nearest CASIO authorized service center.
29
Quick Start Basics
. To replace the memory card
IMPORTANT!
Press the memory card and then release it. This will
cause it to pop out of the memory card slot slightly.
Pull the card out the rest of the way and then insert
another one.
• Turn off the camera before replacing the memory
card.
• The operation lamp (page 8) will flash green for some time after you press [p]
(Power) to turn off the camera. Never remove the memory card while the operation
lamp is flashing green. Doing so can cause the image save operation to fail and
even damage the memory card.
To format (initialize) a new memory card
Format a memory card on the camera before using it for the first time.
IMPORTANT!
• Formatting a memory card that already has snapshots or other files on it, will delete
its contents. Normally you do not need to format a memory card again. However, if
storing to a card has slowed down or if you notice any other abnormality, re-format
the card.
• Be sure to use the camera to format a memory card. Formatting a card on a
computer will result in a non-SD standard format, which can greatly slow down
processing time and cause compatibility, performance, and other problems.
1. Load a memory card (page 29).
2. Turn on the camera and then touch “” (Show Icons).
3. Touch “MENU”.
4. Drag upwards and downwards until you find “Setup”, and then touch it.
5. Touch “Format”.
6. Touch “Format” and then touch “Yes”.
This starts the memory card format operation.
30
Quick Start Basics
Loading...
+ 124 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.