Casio EXILIM EX-MR1 User Guide

Digital Camera
EN
Thank you for purchasing this CASIO product.
• Before using it, be sure to read the precautions contained in this User’s Guide.
• Keep the User’s Guide in a safe place for future reference.
• For the most up-to-date information about this product, visit the official EXILIM Website at http://www.exilim.com/
1

Accessories

As you unpack your camera, check to make sure that all accessories shown below are included. If anything is missing, contact your original retailer.
Rechargeable lithium ion
battery (NP-80)
USB-AC adaptor
(AD-C53U)
Power cord
Basic Reference
* Micro USB cable
Using the Soft Case
When not in use, store the camera in its soft case.
IMPORTANT!
Soft case
• Use the soft case for storage of this camera only.
The mirror side facing upwards
Main materials
Front side:Velvet Inside: Polyester pile
* The shape of the power cord plug varies according to the country or geographic
area where the camera is sold.
2

Read this first!

• The contents of this manual are subject to change without notice.
• The contents of this manual have been checked at each step of the production process. Feel free to contact us if you notice anything that is questionable, erroneous, etc.
• Any copying of the contents of this User’s Guide, either in part or its entirety, is forbidden. Except for your own personal use, any other use of the contents of this manual without the permission of CASIO COMPUTER CO., LTD. is forbidden under copyright laws.
• CASIO COMPUTER CO., LTD. shall not be held liable for any damages or lost profits suffered by you or any third party due to the use or malfunction of this product.
• CASIO COMPUTER CO., LTD. shall not be held liable for any damages or lost profits caused by loss of memory contents due to malfunction, repair, or any other reason.
• Note that the example screens and product illustrations shown in this User’s Guide may differ somewhat from the screens and configuration of the actual camera.
LCD Panel
The liquid crystal panel of the monitor screen uses high-precision technology that provides a pixel yield in excess of 99.99%. This means that some very small number of pixels may not light or may remain lit at all times. This is due to the characteristics of the liquid crystal panel, and does not indicate malfunction.
Take a few test shots
Before shooting your final image, shoot a test shot to ensure that the camera is recording correctly.
3

Contents

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Read this first! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
General Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Monitor Screen Contents and How to Change Them . . . . . . . . . . . . . . . . . . . . 9
]\
Quick Start Basics 12
What you can do with your CASIO camera . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Using the Mirror to Shoot a Self-portrait . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
First, charge the battery prior to use.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
] To load the battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
] Charge the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Configuring Basic Settings the First Time You Turn On the Camera. . . . . . . . 22
Preparing a Memory Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
] Supported Memory Cards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
] To load a memory card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
] To format (initialize) a new memory card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Turning the Camera On and Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Shooting a Snapshot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
] To select an auto recording mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
] To shoot a snapshot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Viewing Snapshots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Deleting Snapshots and Movies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Snapshot Shooting Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
]\
Snapshot Tutorial 35
Using the Control Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Shooting with Artistic Effects . . . . . . . . . . . . . . . . . . . . . . . . (ART SHOT) . . 36
Using BEST SHOT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Using LED Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (LED) . . 40
Using the Self-timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Self-timer) . . 41
Shooting and Playing back Images without Disturbing Others . . . . (Silent) . . 42
Recording Beautiful Portraits . . . . . . . . . . . . . . . . . . . . . . . . . . (Make-up) . . 43
Shooting with Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
]\
Recording Movie Images 45
To record a movie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
4
Contents
]\
Advanced Settings 47
Using On-screen Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
REC Mode Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(REC) . . 49
] Selecting a Focus Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(Focus) . . . 49
] Using Face Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(Face Detection). . . 50
] Using Continuous Shutter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (CS). . . 51
] Reducing the Effects of Camera and Subject Movement . . . . (Anti Shake). . . 52
] Assigning Functions to the [4] and [6 ] Keys . . . . . . . . . . . . . . . (L/R Key). . . 53
] Displaying the On-screen Grid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Grid). . . 53
] Turning on Image Review . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(Review). . . 54
] Using Icon Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Icon Help). . . 54
] Selecting Display Information . . . . . . . . . . . . . . . . . . . . . . . . .(Information) . . . 54
Image Quality Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Quality) . . 55
] To select the snapshot image size . . . . . . . . . . . . . . . . . . . . . . . . . . . (Size). . . 55
] Specifying Movie Image Quality . . . . . . . . . . . . . . . . . .(» Quality (Movie)) . . . 56
] Correcting Image Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . (EV Shift). . . 56
] Controlling White Balance . . . . . . . . . . . . . . . . . . . . . . . . . (White Balance) . . . 57
] Specifying ISO Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(ISO). . . 59
] Optimizing Image Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Lighting). . . 60
] Using Built-in Color Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Color Filter). . . 60
]\
Viewing Snapshots and Movies 61
Viewing Snapshots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Viewing a Movie. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Zooming an On-screen Snapshot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Displaying the Image Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
]\
Other Playback Functions (PLAY) 63
Using the PLAY Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Performing Playback without Disturbing Others . . . . . . . . . . . . . . . (Silent) . . 64
Playing a Slideshow on the Camera . . . . . . . . . . . . . . . . . . . . (Slideshow) . . 64
Inserting a Built-in Subject into a Snapshot . . . . . . . . . . . .(Paste subject) . . 65
Blurring a Playback Image . . . . . . . . . . . . . . . . . . . . . . . . . . . (Blur Effect) . . 66
Auto Image Orientation Detection and Rotation . . . . . . . . . . (Auto Rotate) . . 66
Rotating an Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(Rotation) . . 67
Selecting Images for Printing . . . . . . . . . . . . . . . . . . . . . . (DPOF Printing) . . 67
Protecting a File Against Deletion . . . . . . . . . . . . . . . . . . . . . . . . . (Protect) . . 68
Resizing a Snapshot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Resize) . . 68
Cropping a Snapshot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Trimming) . . 69
Copying Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Copy) . . 70
Selecting Display Information . . . . . . . . . . . . . . . . . . . . . . . . (Information) . . 70
5
Contents
]\
Connecting the Camera with a Smartphone (Wireless LAN) 71
Establishing a Connection between a Smartphone and Your Camera . . . . . . 71
] Installing the EXILIM Link App on Your Smartphone . . . . . . . . . . . . . . . . . . . . . 72
] Sending a Snapshot or Movie File from Camera Memory to a Smartphone . . . 72
Resizing Snapshots before Sending Them
to a Smartphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Resize before send) . . 74
]\
Printing 75
Printing Snapshots. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Using DPOF to Specify Images to be Printed and the Number of Copies. . . . 75
]\
Using the Camera with a Computer 78
Things you can do using a computer... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Using the Camera with a Windows Computer . . . . . . . . . . . . . . . . . . . . . . . . . 79
] Viewing and Storing Images on a Computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
] Playing Movies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Using the Camera with a Macintosh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
] Connecting the Camera to Your Computer and Saving Files . . . . . . . . . . . . . . . 83
] Playing a Movie. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Files and Folders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Memory Card Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
]\
Other Settings (Set Up) 88
Changing the Menu Screen Color . . . . . . . . . . . . . . . . . . . . (Menu Color) . . 88
Resizing Snapshots before Sending Them
to a Smartphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Resize before send) . . 88
Changing the Camera Password for
Wireless LAN Connection . . . . . . . . . . . . . . . . . . . . . . . (WLAN password) . . 88
Configuring Camera Sound Settings . . . . . . . . . . . . . . . . . . . . . (Sounds) . . 89
Configuring a Startup Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Startup) . . 89
Specifying the File Name Serial Number Generation Rule . . . . . (File No.) . . 90
Configuring World Time Settings . . . . . . . . . . . . . . . . . . . . . (World Time) . . 90
Time Stamping Snapshots . . . . . . . . . . . . . . . . . . . . . . . . . . .(Timestamp) . . 91
Setting the Camera’s Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Adjust) . . 92
Specifying the Date Style . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Date Style) . . 92
Specifying the Display Language . . . . . . . . . . . . . . . . . . . . . . (Language) . . 93
Configuring Sleep State Settings . . . . . . . . . . . . . . . . . . . . . . . . . . (Sleep) . . 93
Configuring Auto Power Settings . . . . . . . . . . . . . . . . . . (Auto Power Off) . . 94
Configuring [p] Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (PLAY) . . 94
Formatting Built-in Memory or a Memory Card . . . . . . . . . . . . . . . (Format) . . 95
Resetting the Camera to Factory Defaults . . . . . . . . . . . . . . . . . . . (Reset) . . 95
6
Contents
]\
Appendix 96
Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Precautions During Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Power Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
] Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
] Battery Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
] Using the Camera in another Country . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111
Using a Memory Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111
Reset Initial Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
When things don’t go right... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
] Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
] Display Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Number of Snapshots/Movie Recording Time . . . . . . . . . . . . . . . . . . . . . . . . 121
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
7
Contents

General Guide

The numbers in parentheses indicate the pages where each item is explained.
BackFront
213
4
5
bk bl
[ ]
[ ]
[ ]
6
9
Shutter button (page 28)
1
Microphone (page 46)
2
[p] (Power) (page 26)
3
USB port (pages 17, 19)
4
Memory card slot
5
(page 24) [CARD USB] cover
6
LED light (page 40)
7
Lens
8
Lens is inside the mirror surface.
Bottom
78
Mirror (page 14)
9
[ ] (Wi-Fi) button
bk
(page 72) [0] (Movie) button
bl
(page 45) Strap hole (page 8)
bm
Back lamp
bn
(pages 18, 20) [p] (PLAY) button
bo
(pages 26, 31)
Battery slot (page 16)
bt
Battery cover
ck
Speaker
cl
bobp bn bmbqbrbs
[MENU] button
bp
(page 47) [SET] button (page 35)
bq
Control button
br
([8][2][4][6]) (pages 35, 47, 63) Monitor screen (page 9)
bs
[
SET
[ ]
]
btckcl
To attach the strap (commercially available) to the camera
Attach strap here.
1
2
8

Monitor Screen Contents and How to Change Them

The monitor screen uses various indicators, icons, and values to keep you informed of the camera’s status.
• The sample screens in this section are intended to show you the locations of all the indicators and figures that can appear on the monitor screen in various modes. They do not represent screens that actually appear on the camera.
. Snapshot Recording
Remaining snapshot memory capacity
1
(page 121) Remaining movie memory capacity (page 45)
2
bk
Silent mode (page 42)
3
bl
Recording mode (page 27)
4
bm
White balance (page 57)
5
Continuous shutter (page 51)
6
bn
Image deterioration indicator (page 44)
7
bo
Metering mode (page 122)
8
Snapshot image size (page 55)
9
Movie image quality (page 56)
bk
LED light (page 40)
bl
Self-timer (page 41)
bm
Make-up (page 43)
bn
Lighting (page 60)
bo
Date/time (page 92)
bp
ISO sensitivity (page 59)
bq
Exposure compensation (page 56)
br
Focus frame (pages 29, 49)
bs
Timestamp indicator (page 91)
bt
Battery level indicator (page 21)
ck
Face Detection (page 50)
cl
Anti Shake (page 52)
cm
Focus mode (page 49)
cn
cn cm
cl
ck
2
bt
bs
br bq
89341657
bp
9
. Shutter Button Half-pressed
Recording mode (page 27)
1
5
1
ISO sensitivity (page 59)
2
Aperture value
3
Shutter speed
4
Focus frame (pages 29, 49)
5
2 3 4
NOTE
• Depending on recording settings, the aperture, shutter speed, and ISO sensitivity values may not appear on the monitor screen. These values will be orange if the Auto Exposure (AE) is not correct for some reason.
. Movie Recording
Recording mode (page 45)
12
8 7
1
White balance (page 57)
2
Remaining movie memory capacity (page 45)
3
3
Movie recording time (page 45)
4
4
Exposure compensation (page 56)
5
Battery level indicator (page 21)
6
Anti Shake (page 52)
7
Movie recording in progress (page 45)
8
6 5
10
. Snapshot Viewing
31
bl
. Movie Playback
2 31
9
4
Silent mode (page 64)
5
6 7 8 9 bk
5 6 7
8
1
File type
2
Protect indicator (page 68)
3
Folder name/file name (page 86)
4
Snapshot image size (page 55)
5
Currently supported control button (page 8)
6
operations. ISO sensitivity (page 59)
7
Aperture value
8
Shutter speed
9
Date/time (page 92)
bk
Battery level indicator (page 21)
bl
Silent mode (page 64)
1
File type
2
Protect indicator (page 68)
3
Folder name/file name (page 86)
4
Movie recording time (page 45)
5
Movie image quality (page 56)
6
Currently supported control button (page 8)
7
operations. Date/time (page 92)
8
Battery level indicator (page 21)
9
42
11

Quick Start Basics

What you can do with your CASIO camera

Your CASIO camera is packed with a powerful selection of features and functions to make recording of digital images easier, including the following main functions.
Simple self-shooting
Shoot self-portraits as you compose using the camera’s front mirror.
*See page 14 for more information.
Premium Auto
Select Premium Auto recording and the camera automatically determines whether you are shooting a subject or scenery, and other conditions. Premium Auto delivers higher image quality than standard Auto.
*See page 27 for more information.
Make-up Function
The Make-up Function smoothes the skin texture of the subject and softens facial shadows caused by harsh sunlight for better looking portraits.
*See page 43 for more information.
ART SHOT
A variety of artistic effects help to make even common, ordinary subjects become more novel and exciting.
*See page 36 for more information.
Silent
The Silent mode disables LED light operation, mutes camera operation tones, and changes other settings to help ensure that shooting does not bother others around you.
*See pages 42, 64 for more information.
BEST SHOT
Simply select the sample scene you want and the camera sets up automatically. Then all you need to do is press the shutter button for perfect images.
*See page 38 for more information.
12
Quick Start Basics
Paste subject
A simple operations embeds stars, hearts and other graphic symbols into a photograph. Frames can also be added.
*See page 65 for more information.
Art Effect
Apply art effects to images you shoot.
*See page 63 for more information.
Wireless LAN Connection
Images shot with the camera can be sent to a smartphone.
*See page 71 for more information.
13
Quick Start Basics

Using the Mirror to Shoot a Self-portrait

The front of the camera is a mirror, which make it easy to compose images even when shooting a self-portrait. When shooting, hold the camera so the LED light is at the top.
Holding with the left hand
Holding with the right hand
LED light
Shutter button
LED light
Shutter button
. Precautions when shooting a self-portrait
• Depending on the shooting distance, the range of the image being reflected by the mirror may be different from the range of the image that will actually be shot by the camera. It is recommended that you check images by displaying them on the monitor screen after shooting them.
lens
. Mirror Precautions
• The lens is approximately in the center of the mirror. Dirt in the area of the lens can cause unwanted marks in recorded images.
• Do not scratch, press, or strike the mirror with strong force. Doing so can scratch or soil the mirror.
• Damage or soiling in the center of the mirror (lens area) can interfere with proper operation of the camera.
• Affixing protective film to the center (lens area) of the mirror can affect image quality and interfere with proper operation of the camera.
• When shooting in a sunny area, the mirror will reflect sunlight. This creates the risk of eye problems. Take care to avoid allowing sunlight to shine onto the mirror.
14
Quick Start Basics
NOTE
• The mirror has a curved surface, so there may be some distortion in the reflected image. This does not affect recorded images.
• When shooting hold the camera still. Carefully press the shutter button and take care to avoid all movement as the shutter releases and for a few moments after it releases.
• Take care that your fingers and the strap do not cover
Microphone
any of the areas indicated in the illustration.
• To protect against accidentally dropping the camera, attach the wrist strap (commercially available or separately available) and make sure it is around your fingers or wrist while you are operating the camera.
• Never swing the camera around by its strap.
IMPORTANT!
Lens
LED light
• Take care to ensure that your fingers are not blocking or is not too close to the LED light as shown in the nearby illustration. Fingers can cause unwanted shadows when shooting.
15
Quick Start Basics

First, charge the battery prior to use.

Note that the battery of a newly purchased camera is not charged. Perform the steps below to load the battery into the camera and charge it.
• Your camera requires a special CASIO rechargeable lithium ion battery (NP-80) for power. Never try to use any other type of battery.

To load the battery

1. Open the battery cover.
2. Load the battery.
With the CASIO logo on the battery facing downwards (in the direction of the monitor screen), hold the stopper next to the battery in the direction indicated by the arrow as you slide the battery into the camera. Press the battery in until the stopper secures it in place.
3. Close the battery cover.
OK
Battery
Stopper
NG
CASIO logo
16
Quick Start Basics
To replace the battery
Stopper
1. Open the battery cover and
remove the current battery.
2. Load a new battery.

Charge the Battery

You can use either of the two following methods to charge the camera’s battery.
• USB-AC adaptor
• USB connection to a computer
. To charge with the USB-AC adaptor
The adaptor lets you charge the battery while it is loaded in the camera. While the camera is turned off, connect in the sequence shown below. Charging time: Approximately 150 minutes
[USB] port
Micro USB cable (included with camera)
4
1
u mark of the small (micro USB) connector facing the mirror side.
• When disconnecting the USB-AC adaptor from the camera, be sure to disconnect from the camera first.
USB-AC adaptor
(AD-C53U)
17
2
Power cord
3
Quick Start Basics
IMPORTANT!
• Make sure that you insert the cable connector into the USB port until you feel it click securely into place. Failure to insert the connector fully can result in poor communication or malfunction.
• Note that even while the connector is fully inserted, you still will be able to see the metal part of the connector as shown in the illustration.
•Pressing [p] (Power) while the USB-AC adaptor is connected to the camera will turn on the camera. Because of this, charging will stop.
• The USB-AC adaptor will become warm during charging. This is normal and does not indicate malfunction.
• The shape of the power plug depends on each country or geographic area.
Back Lamp Operation
Lamp Status Description
Back lamp
Lit Red Charging
Abnormal ambient temperature, USB-
Flashing Red
AC adaptor problem, or battery problem (page 110)
Off Charging complete
18
Quick Start Basics
. To charge using a USB connection to a computer
USB connection lets you charge the battery while it is loaded in the camera. While the camera is turned off, connect in the sequence shown below ( camera is on, press [p]
1, 2
). If the
(Power) to turn it off before connecting it to your computer. Charging time: Approximately 150 minutes
1
u mark of the small (micro USB) connector facing the mirror side.
[USB] port
Micro USB cable
(included with camera)
IMPORTANT!
• The first time you connect the camera to your computer with the USB cable, an error message may appear on your computer. If this happens, disconnect and then reconnect the USB cable.
• Depending on the setup of your computer, you may not be able to charge the camera’s battery over a USB connection. If this happens, use of the USB-AC adaptor that comes with the camera is recommended.
• Charging is not performed while the connected computer is in the hibernate mode.
Computer
(power turned on)
USB port
2
USB
19
Quick Start Basics
Back Lamp Operation
Lamp Status Description
Lit Red, (Lit/Flashing Amber)
Charging
Back lamp
Abnormal ambient temperature,
Flashing Red
charging taking abnormally long, or battery problem (page 110)
Off, (Lit Green) Charging complete
• The information in parentheses in the above table shows the lamp status while the camera is turned on during charging.
Other Charging Precautions
• With the two charging methods described above, you can charge the camera’s battery (NP-80) without removing it from the camera. You also can charge the battery using an optionally available charger unit (BC-80L). Never use any other type of charger device. Attempting to use a different charger can result in unexpected accident.
• USB charging devices and power supply devices are subject to fixed standards. Use of an inferior device or a device that is not up to standard can cause malfunction and/or failure of your camera.
• Operation is not guaranteed in the case of a computer built or modified by you. Even in the case of a commercially available computer, certain USB port specifications may make it impossible to charge via the USB cable.
• A battery that is still warm due to normal use may not charge fully. Give the battery time to cool before charging it.
• A battery discharges slightly even when it is not loaded in the camera. Because of this, it is recommended that you charge the battery immediately before you need to use it.
• Charging the camera’s battery may cause interference with TV and radio reception. If this happens, plug the charger into an outlet that is further away from the TV or radio.
• Actual charging time depends on current battery capacity and charging conditions.
• Do not use the USB-AC adaptor with any other device.
• Never use the power cord with another device.
• Use only the USB-AC adaptor and USB cable specified in this manual for charging. Use of any other type of devices may result in improper charging.
20
Quick Start Basics
Checking Remaining Battery Power
As battery power is consumed, a battery indicator on the monitor screen indicates remaining power as shown below.
Remaining Power High Low
Battery Indicator ***
Indicator Color Cyan * Amber * Red * Red
indicates battery power is low. Charge the battery as soon as possible.
Recording is not possible when is indicated. Charge the battery immediately.
• The level shown by the battery indicator may change when you switch between the REC mode and PLAY mode.
• Leaving the camera for about 30 days with no power supplied while the battery is dead will cause its date and time settings to be cleared. A message telling you to configure time and date settings will appear the next time you turn on the camera after restoring power. When this happens, configure date and time settings (page
92).
• See page 124 for information about battery life and number of shots.
Battery Power Conservation Tips
• Enable the Auto Power Off and the Sleep features to protect against wasting battery power when you forget to turn off the camera (pages 93, 94).
21
Quick Start Basics

Configuring Basic Settings the First Time You Turn On the Camera

The first time you load a battery into the camera, a screen appears for configuring the display language, date, and time settings. Failure to set the date and time correctly will cause the wrong date and time data to be recorded with images.
IMPORTANT!
• A screen for language selection will not appear in step 2 of the procedure below if you purchased a camera intended for the Japanese market. To change the display language from Japanese in this case, use the procedure under “Specifying the Display Language (Language)” (page 93). Note that a version of this manual in the language you select may not be included with a camera intended for the Japanese market.
• Camera models sold in certain geographic areas may not support display language selection.
1. Hold down [p] (Power) until the back
lamp lights green momentarily.
[p] (Power)
2. Use [8], [2], [4], and [6] to select
the language you want and then press [SET].
3. Use [8] and [2] to select a date style
and then press [SET].
Example: July, 10, 2016 YY/MM/DD DD/MM/YY MM/DD/YY
* 16/7/10 * 10/7/16 * 7/10/16
[0] (Movie)
4. Set the date and the time.
Use [4] and [6] to select the setting you want to change and then use [8] and [2] to change it. To switch between 12-hour and 24-hour format, press [0] (Movie).
5. After setting the date and time, use [4] and [6]
to select “Apply” and then press [SET].
Back lamp
22
Quick Start Basics
If you make a mistake configuring display language, date, or time settings with the above procedure, refer to the following pages for information about how to correct the settings.
– Display language: Page 93 – Date and time: Page 92
NOTE
• Each country controls its local time offset and the use of summer time, and so they are subject to change.
• Removing the battery from the camera too soon after configuring time and date settings for the first time can cause the settings to be reset to their factory defaults. Do not remove the battery for at least 24 hours after configuring settings.

Preparing a Memory Card

Though the camera has built-in memory that can be used to store images and movies, you probably will want to purchase a commercially available memory card for greater capacity. The camera does not come with a memory card. Images recorded while a memory card is loaded are saved to the memory card. When no memory card is loaded, images are saved to built-in memory.
• For information about memory card capacities, see page 121.

Supported Memory Cards

– microSD Memory Card – microSDHC Memory Card – microSDXC Memory Card
• The above are supported memory card types as of August
2014.
• This camera supports use of microSD memory cards of the following types and capacities: microSD memory cards up to 2GB, microSDHC memory cards from 2GB up to 32GB, microSDXC memory cards from 32GB up to 2TB. Note that the ability to use any particular card with this camera, even if it satisfies the above capacity and type requirements, is not guaranteed.
. Memory Card Handling Precautions
Certain types of memory cards can slow down processing speeds, and even can make it impossible to store High Quality movies correctly. Also, use of certain types of memory cards slows down data transfer and increases the time it takes to record movie data, which can result in breaks in the image and/or audio during playback. If this happens, » and Y flash on the monitor screen.
23
Quick Start Basics
Warning!
*
microSD/microSDHC/microSDXC memory cards present a swallowing
+
hazard for small children.
Keep microSD/microSDHC/microSDXC memory cards out of the reach of
+
small children. Should a memory card ever be swallowed accidentally, consult a physician immediately.

To load a memory card

1. Press [p] (Power) to turn off the
camera and then open the [CARD USB] cover.
2. Load a memory card.
Positioning the memory card so its front is facing downwards (towards the monitor screen side of the camera), slide it into the card slot all the way in until you hear it click securely into place.
Back
3. Close the [CARD USB] cover.
24
Front Back
Quick Start Basics
IMPORTANT!
• Never insert anything besides a supported memory card (page 23) into the memory card slot.
• Should water or any foreign object ever get into the card slot, immediately turn off the camera, remove the battery, and contact your retailer or nearest CASIO authorized service center.
To replace the memory card
Press the memory card and then release it. This will cause it to pop out of the memory card slot slightly. Pull the card out the rest of the way and then insert another one.
• Never remove a card from the camera while the back lamp is flashing green. Doing so can cause the image save operation to fail and even damage the memory card.

To format (initialize) a new memory card

Format a memory card on the camera before using it for the first time.
IMPORTANT!
• Formatting a memory card that already has snapshots or other files on it, will delete its contents. Normally you do not need to format a memory card again. However, if storing to a card has slowed down or if you notice any other abnormality, re-format the card.
• Be sure to use the camera to format a memory card. Formatting a card on a computer will result in a non-SD standard format, which can greatly slow down processing time and cause compatibility, performance, and other problems.
1. Press [p] (Power) to turn on the camera and then press [MENU].
2. Use [4] and [6] to select the “Set Up” tab.
3. Use [8] and [2] to select “Format” and then press [6].
4. Use [8] and [2] to select “Format” and then press [SET].
25
Quick Start Basics

Turning the Camera On and Off

. To turn power on
Pressing [p] (Power) enters the REC mode so you can record images. Pressing [p] (PLAY) while in the REC mode enters the PLAY mode, which you can use to view snapshots and movies (pages 31, 61).
•Pressing [p] (PLAY) turns on the camera and enters the PLAY mode.
• Pressing the shutter button while in the PLAY mode returns to the REC mode.
• Take care to ensure that nothing is restricting or coming into contact with the lens as it extends. Holding the lens with your hand so it cannot extend creates the risk of malfunction.
• About 10 seconds after you press [p] (PLAY) to enter the PLAY mode, the lens will retract into the camera.
• The Sleep function or Auto Power Off (pages 93, 94) will turn off power automatically if you do not perform any operation for a preset amount of time.
. To turn off the camera
Press [p] (Power).
NOTE
• You also can configure the camera to turn on or off when you press [p] (PLAY) (page 94).
[p] (Power)
Shutter button
[p] (PLAY)
26
Quick Start Basics

Shooting a Snapshot

R

To select an auto recording mode

In addition to the two auto recording modes, the camera also has ART SHOT and BEST SHOT modes to suit a variety of digital imaging needs. This section explains general shooting procedures using an auto recording mode. For information about other recording modes, see pages 36 and 38.
Setting
Auto This is the standard Auto recording mode.
Ÿ
Premium
Auto
REC Screen Icon Display
Description
With Premium Auto recording, the camera automatically determines whether you are shooting a subject or scenery, and other conditions. Premium Auto recording delivers higher image quality than standard Auto recording.
• Some of the settings configured automatically by Premium Auto cannot be changed by you.
• Premium Auto recording takes longer to process image data after it is shot than Auto recording.
• It also requires more power (and runs down the battery quicker) than Auto.
1. Press [p] (Power) to turn on the camera.
The camera will enter the REC mode.
• If the camera is in the PLAY mode, press the shutter button.
2. Press [SET].
3. Use [8] and [2] to select the top Control Panel option (Recording
mode) (page 35).
27
Quick Start Basics
4. Use [4] and [6] to select “Auto” or “Premium Auto”, and then press
[SET].
This enters the selected auto recording mode.
Auto recording mode icon
Remaining Snapshot Memory Capacity (page 121)
[p] (Power)
Monitor screen

To shoot a snapshot

1. Point the camera at the subject.
If you are using Premium Auto, text will appear in the lower right corner of the monitor screen describing the type of shot the camera has detected.
• You can zoom the image using [8] and [2], if you
want.
w Wide Angle z Telephoto
Shutter button
[SET]
[8][2][4][6]
28
Quick Start Basics
2. Half-press the shutter button to
Back lamp
focus the image.
When focus is complete, the camera will beep, the back lamp will light green, and the focus frame will turn green.
Focus frame
Half-press
Press lightly until the button stops.
Beep, beep (Image is in focus.)
When you half-press the shutter button, the camera automatically adjusts exposure and focuses on the subject it is currently pointed at. Mastering how much pressure is required for a half-press and a full-press of the shutter button is an important technique for good-looking images.
3. Continuing to keep the camera still, press the shutter button the rest of
the way down.
This records the snapshot.
Full-press
Recording a Movie
Press [0] (Movie) to start movie recording. Press [0] (Movie) again to stop movie recording. See page 45 for details.
[0] (Movie)
Snap (Image is recorded.)
29
Quick Start Basics
. If the image does not focus...
If the focus frame stays red and the back lamp is flashing green, it means that the image is not in focus (because the subject is too close, etc.). Re-point the camera at the subject and try to focus again.
. Shooting with Auto
“Focus lock” (page 49) is the name of a technique you can use when you want to shoot an image in which the subject to be focused on is not within the focus frame in the center of the screen.
. Shooting with Premium Auto
• When shooting with Premium Auto, you can use the menu screen (page 47) to change the settings of only the menu items below. No other menu items will appear on the menu while you are shooting with Premium Auto. – REC: Grid, Review, Icon Help, Information – Quality: Size, » Quality (Movie), EV Shift – Set Up: All items
• In addition to shutter speed, aperture, and ISO sensitivity, the camera automatically executes the following operation as required when shooting with Premium Auto. – Auto Focus is normally performed until you half-press the shutter button. – The camera automatically determines the focus point on the screen and focuses
there.
– Make-up (page 43)
Under the initial default camera setup when you purchase it, selecting Premium Auto as the auto recording mode (page 27) turns on the Make-up function.
• In some cases, Premium Auto may not be able to interpret the shooting environment correctly. If this happens, shoot with standard Auto.
30
Quick Start Basics

Viewing Snapshots

Use the following procedure to view snapshots on the camera’s monitor screen.
• For information about how to play back movies, see page 61.
1. Press [p] (PLAY) to enter the
PLAY mode.
• This will display one of the snapshots currently stored in memory.
• Information about the displayed snapshot also is included (page 11).
• You also can clear the information to view only the snapshot (page 70).
• You can zoom in on the image by pressing [8] (page 62). If you are recording a snapshot that is very important to you, it is recommended that you zoom the image and check its details after recording it.
[p] (PLAY)
2. Use [4] and [6] to scroll between images.
• Holding down either button scrolls at high speed.
[6]
[6]
[4]
NOTE
• Half-pressing the shutter button while in the PLAY mode or while a menu screen is displayed will switch directly to the REC mode.
31
[4]
Quick Start Basics

Deleting Snapshots and Movies

If memory becomes full, you can delete snapshots and movies you no longer need in order to free up storage and record more images.
IMPORTANT!
• Remember that a file (image) delete operation cannot be undone.
[SET]
. To delete a single file
1. Enter the PLAY mode, and then press [SET].
2. Use [8] and [2] to select the “Ü” (Delete) PLAY Panel
option, and then press [SET].
3. Use [4] and [6] to scroll through the files until the one you want to
delete is displayed.
4. Use [8] and [2] to select “Delete” and then press [SET].
• To delete other files, repeat steps 3 and 4.
• To exit the delete operation, press [MENU].
32
Quick Start Basics
. To delete specific files
1. Enter the PLAY mode, and then press [SET].
2. Use [8] and [2] to select the “Ü” (Delete) PLAY Panel option, and
then press [SET].
3. Use [8] and [2] to select “Delete Files” and then press [SET].
• This displays a file selection screen.
4. Use [8], [2], [4], and [6] to move the selection boundary to the file
you want to delete, and then press [SET].
• This will select the check box of the currently selected file.
5. Repeat step 4 to select other files, if you want. After you are finished
selecting files, press [MENU].
6. Use [8] and [2] to select “Yes” and then press [SET].
• This deletes the files you selected.
• To exit the delete operation, press [MENU].
. To delete all files
1. Enter the PLAY mode, and then press [SET].
2. Use [8] and [2] to select the “Ü” (Delete) PLAY Panel option, and
then press [SET].
3. Use [8] and [2] to select “Delete All Files” and then press [SET].
4. Use [8] and [2] to select “Yes” and then press [SET] to delete all files.
This will cause the message “There are no files.” to appear.
33
Quick Start Basics

Snapshot Shooting Precautions

Operation
• Never open the battery cover while the back lamp is flashing green. Doing so can result in the image you just shot being saved incorrectly, damage to other images stored in memory, malfunction of the camera, etc.
Monitor Screen when Shooting Snapshots
• Subject brightness conditions can cause monitor screen response to slow and can cause digital noise in the monitor screen image.
• The image that appears on the monitor screen is for image composition. The actual image will be recorded at the quality set for the image quality setting (page 55).
Shooting Indoors under Fluorescent Lighting
• Minute flickering of fluorescent lighting can affect the brightness or color of an image.
. Auto Focus Restrictions
• Any of the following can make proper focus impossible. – Solid color wall or other very low contrast subject – Strongly back lit subject – Very shiny subject – Blinds or other subject with a repeating horizontal pattern – Multiple subjects at varying distances from the camera – Subject in a dark location – Camera movement while shooting – Fast-moving subject – Subjects outside the focus range of the camera
• If you cannot focus properly, try using focus lock (page 49).
34
Quick Start Basics

Snapshot Tutorial

Using the Control Panel

The Control Panel can be used to configure camera settings.
1. In the REC mode, press [SET].
[SET]
[8] [2] [4] [6]
Available settings
2. Use [8] and [2] to select the setting you want to change.
This will select one of the Control Panel icons and display its settings.
Recording mode (pages 27, 36, 38)
1
LED light (page 40)
2
Self-timer (page 41)
3
4 5
3. Use [4] and [6] to change the setting.
4. If you want to configure another setting, repeat steps 2 and 3.
5. After all of the settings are the way you want, press [SET].
This will apply the settings and return to the REC mode.
• You can close the Control Panel by pressing [MENU].
Control Panel
1 2 3 4 5
Silent mode (page 42) Make-up (page 43)
NOTE
• No icon is displayed for any Control Panel option (page 9) that is set to its initial default (reset) setting. An icon will appear only if you change the setting of the corresponding Control Panel option. The following are the initial defaults for Control Panel options. – Self-timer: Off – Make-up: Off
• You also can configure settings other than those listed above (page 47).
35
Snapshot Tutorial

Shooting with Artistic Effects (ART SHOT)

A variety of artistic effects help to make even common, ordinary subjects become more novel and exciting.
Scene Description
Toy Camera
Soft Focus Overall blurring for a soft and romantic effect.
Light Tone Weakened contrast for a feeling of airy refinement.
Pop
Sepia Sepia tones create a decidedly retro look.
Monochrome
Miniature
Fisheye
Crystal Ball
Dark edges and altered hues make images look like they were shot by a toy camera.
Enhanced saturation makes colors stand out in with rich clarity.
All of the strong contrast and graininess of a black and white print.
Partial blurring makes scenes look like they are from of a miniature world.
A fisheye lens effect can be used to create a variety of humorous images.
Creates a mysterious effect by placing the image in a bubble floating in midair.
1. In the REC mode, press [SET].
2. Use [8] and [2] to select the top Control Panel option (Recording
mode) (page 35).
3. Use [4] and [6] to select “ART” (ART SHOT), and then press [SET].
4. Use [8], [2], [4] and [6] to move the boundary to the scene you want
to select.
• You can access information about the currently selected scene. See page 37 for details.
5. Press [SET] to configure the camera with the settings for the currently
selected scene.
This returns to the REC mode.
• The settings of the scene you selected remain in effect until you select a different scene.
• To select a different ART SHOT scene, repeat the above procedure from step
1.
6. Press the shutter button to shoot.
36
Snapshot Tutorial
NOTE
• Movie recording is disabled while “ART SHOT” is selected.
• The ART SHOT cannot be used together with the following features. CS, Make-up, Color Filter
• Face detection can be used only while one of the ART SHOT scenes below is selected. Toy Camera, Soft Focus, Light Tone
. Using Scene Information Screen
To find out more about a scene, select it with the boundary on the scene selection screen, and then press [MENU].
• To return to the scene menu, press [MENU].
• To scroll between scenes, use [
• To configure the camera with the settings for the currently selected scene, press [SET].
4] and [6].
37
Snapshot Tutorial

Using BEST SHOT

BEST SHOT provides you with a collection of sample “scenes” that show a variety of different types of shooting conditions. When you need to change the setup of the camera, simply find the scene that matches what you are trying to achieve, and the camera sets up for it automatically. This helps to minimize the chance of ruined images due to poor exposure and shutter speed settings.
1. In the REC mode, press [SET].
[SET]
Currently selected scene (with boundary)
2. Use [8] and [2] to select the top
Control Panel option (Recording mode) (page 35).
3. Use [4] and [6] to select “b”
(BEST SHOT), and then press [SET].
This will display a menu of BEST SHOT scenes.
[8] [2] [4] [6]
Scene name
Scene number
4. Use [8], [2], [4], and [6] to
move the boundary to the scene you want to select.
• The scene menu has multiple pages. Use [8] and [2] to scroll between menu
pages.
• You can access information about the currently selected scene. See page 39 for details.
5. Press [SET] to configure the camera with the settings for the currently
selected scene.
This returns to the REC mode.
• The settings of the scene you selected remain in effect until you select a different scene.
• To select a different BEST SHOT scene, repeat the above procedure from step 1.
6. Press the shutter button (if you are shooting a snapshot) or [0] (Movie)
(if you are shooting a movie).
• To return to the auto recording mode, press [SET], use [8] and [2] to select the top Control Panel option (Recording mode), and then select R (Auto) or Ÿ (Premium Auto).
38
Snapshot Tutorial
. Using Scene Information Screen
To find out more about a scene, select it with the boundary on the scene selection screen, and then press [MENU].
• To return to the scene menu, press [MENU].
• To scroll between scenes, use [
• To configure the camera with the settings for the currently selected scene, press [SET].
4] and [6].
. BEST SHOT Precautions
• Some BEST SHOT scenes cannot be used while recording a movie.
• Some scenes like “Night Scene Portrait” results in a slow shutter speed setting. Since a slow shutter speed increases the chance of digital noise in the image, the camera automatically performs a digital noise reduction process when either of these scenes is selected. This means that it will take a bit longer for the image to be saved which is indicated by the back lamp flashing green. Do not perform any key operation during that time.
• BEST SHOT scene images were not shot using this camera.
• Images shot using a BEST SHOT scene may not produce the results you expected due to shooting conditions and other factors.
• You can modify the camera settings that are made after you select a BEST SHOT scene. Note, however, that the BEST SHOT settings revert to their defaults when you select another BEST SHOT scene or turn off the camera.
39
Snapshot Tutorial

Using LED Light (LED)

Use the LED light when shooting where lighting is dim. The effectiveness of the LED light is reduced the further you are from the subject.
1. In the REC mode, press [SET].
LED light
2. Use [8] and [2] to select the “LED light” Control
Panel option (page 35).
3. Use [4] and [6] to select the setting you want and
then press [SET].
Setting
Auto
On LED always lights when shooting.
Off None LED never turns on or fires.
REC Screen Icon Display
Description
The LED light fires automatically under dark shooting conditions when the shutter button is half-pressed to focus and/or full-pressed to shoot.
4. Press the shutter button to shoot.
IMPORTANT!
• Do not turn on the LED light near a person’s eyes and do not allow anyone to look directly into the light.
• You should compose the image so the main subject is in the center of the image when using the LED light.
• Since the camera is equipped with a wide-angle lens, the center tends to be brighter while the periphery tends to be darker.
40
Snapshot Tutorial

Using the Self-timer (Self-timer)

Ñ
Ì
Ï
Î
With the Self-timer, pressing the shutter button starts a timer. The shutter is released and the image is shot after a fixed amount of time.
1. In the REC mode, press [SET].
2. Use [8] and [2] to select the “Self-timer” Control Panel option (page
35).
3. Use [4] and [6] to select the setting you want and then press [SET].
Setting
10sec
Self-timer
2sec
Self-timer
×3 Self­timer (Triple Self-timer)
Self-
timer Off
• The LED light flashes while the Self-timer countdown is in progress.
• You can interrupt an ongoing Self-timer countdown by pressing [SET].
NOTE
• The Self-timer cannot be used together with the following features. CS
• The Triple Self-timer cannot be used together with the following features. Movie, Make-up, ART SHOT
REC Screen Icon Display
None Turns off the Self-timer.
Description
10-second Self-timer
2-second Self-timer
• When shooting under conditions that slow down the shutter speed, you can use this setting to prevent image blur due to camera movement.
Shoots three images: one image 10 seconds after the shutter button is pressed, and the next two images as soon as the camera is ready after shooting the previous image. How long it takes for the camera to get ready to shoot depends on the image size and quality settings and whether or not a memory card is loaded in the camera.
LED light
41
Snapshot Tutorial

Shooting and Playing back Images without Disturbing Others (Silent)

The Silent mode automatically configures camera settings to avoid disturbing others around you. It disables LED light operation and mutes camera operation tones, audio during movie playback. This comes in handy when shooting or playing back in a museum or other areas where care is required when operating the camera.
1. In the REC mode, press [SET].
2. Use [8] and [2] to select the “Silent” Control Panel option (page 35).
3. Use [4] and [6] to select “On” and then press [SET].
This enters the Silent mode, which is indicated by m (Silent Mode) on the monitor screen.
• The settings shown below are fixed and cannot be changed while in the Silent mode.
Setting Description
LED light Off
Self-timer Off
Sounds Off
• See the following for details. – LED light (page 40) – Self-timer (page 41) – Sounds (page 89)
• Entering the Silent mode in the REC mode will also enter the Silent mode in the PLAY mode automatically (page 64).
42
Snapshot Tutorial

Recording Beautiful Portraits (Make-up)

Make-up enables adjustment of human skin tone hues and texture, and softening of facial shadows caused by harsh sunlight for better looking portraits. Make-up can be used with the recording modes listed below.
1. In the REC mode, press [SET].
2. Use [8] and [2] to select the “Make-up” Control Panel option (page
35), and then press [SET].
3. Use [8] and [2] to select “Skin Tone” or “Smooth Skin”, and then use
[4] and [6] to change the setting value.
Skin Tone “0” to “Light +6”
Smooth Skin “0” to “+12”
4. Press [SET].
5. Point the camera at the subject and shoot.
NOTE
• Face Detection (page 50) automatically turns on whenever the “Skin Tone” or “Smooth Skin” level setting is something other than “0”.
• Make-up cannot be used with the following functions. Movie recording, ART SHOT, CS, Triple Self-timer
43
Snapshot Tutorial

Shooting with Zoom

Your camera is equipped with various types of zoom: HD Zoom, SR Zoom, and digital zoom. The maximum zoom factor depends on the image size setting.
HD Zoom
SR Zoom
Digital zoom
Allows greater zoom capabilities by cutting out a portion of the original image and enlarging it, without deterioration of image quality.
Applies super resolution technology to suppress image deterioration.
A digital process is used to enlarge the center of the image, so there is deterioration of image quality.
1. In the REC mode, press [8] or [2] to zoom.
w Wide Angle z Telephoto
[2] (Wide Angle): Reduces the size of the subject and broadens the range. [8] (Telephoto) : Enlarges the subject and narrows the range.
[8] [2]
2. Press the shutter button to shoot the image.
NOTE
•“Ù” is displayed on the monitor screen while digital zoom is being used.
. Zoom Factor
The image deterioration point depends on the image size (page
55). The smaller the image size, the higher the zoom factor you can use before reaching the image deterioration point.
IMPORTANT!
• When shooting with the ART SHOT Crystal Ball scene, the maximum zoom factor is 2.0X.
Image
44
Undeteriorated
Size
14M 2.0X 4.0X
3M 4.2X 8.4X
zoom limit
Maximum
Zoom Factor
Snapshot Tutorial

Recording Movie Images

To record a movie

1. Configure the quality setting for the movie (page 56).
The length of the movie you can record will depend on the quality setting you select.
2. In the REC mode, point the
camera at the subject and then press [0] (Movie).
This will start recording and display Y on the monitor screen. Movie recording includes monaural audio.
[0] (Movie)
Remaining recording time
(page 121)
3. Press [0] (Movie) again to stop
recording.
• Each movie can be up to 29 minutes long. Movie recording stops automatically after 29 minutes of recording. Movie recording also will stop automatically if memory becomes full before you stop movie recording by pressing [0] (Movie).
Shooting with BEST SHOT
With BEST SHOT (page 38), you can select the sample scene that matches the type of movie you are trying to shoot and the camera will change its setup accordingly, for beautiful movies every time.
Image stabilization during movie recording
Image stabilization is always enabled during movie recording. Note, however, that image stabilization does not prevent image blur due to subject movement during movie recording. Also, image stabilization results in a narrower angle of view during movie recording.
Recording time
45
Recording Movie Images
NOTE
• Spending a long time using movie recording will cause the camera to become slightly warm to the touch. This is normal and does not indicate malfunction.
• The camera also records audio. Note the following points
Microphone
when shooting a movie. – Take care that the microphone is not blocked by your
fingers, etc.
– Good recording results are not possible when the
camera is too far away from what you are trying to record.
• Shooting a very bright subject can cause a vertical band or a pink cast on the monitor screen image. This does not indicate malfunction.
• Using the camera’s built-in memory or certain types of memory cards can slow down processing speeds, and even can make it impossible to store High Quality movies correctly. Also, use of certain types of memory cards slows down data transfer and increases the time it takes to record movie data, which can result in breaks in the image and/or audio during playback. If this happens, the » and Y flash on the monitor screen.
• The effects of camera movement in an image become more pronounced when you shoot close up or with a large zoom factor.
• You can use the [4] and [6] keys during movie recording to adjust the EV shift setting.
46
Recording Movie Images

Advanced Settings

The following are menu operations you can use to configure various camera settings.
• REC mode menu contents and operations are different from those in the PLAY mode. This section explains operations using the REC menu screen. See page 63 for information about PLAY menu screen operations.

Using On-screen Menus

. Example REC Menu Screen Operation
1. In the REC mode, press [MENU].
This will display the REC menu screen.
2. Use [4] and [6] to select the tab where the menu
item you want to configure is located.
3. Use [8] and [2] to select the menu item you
want, and then press [6].
4. Use [8] and [2] to change the setting of the
selected menu item.
5. After the setting is the way you want, press
[SET] to apply the setting and return to the viewfinder screen.
• Pressing [4] instead of [SET] applies the
selected setting and returns to the menu item selection.
• To configure settings on another tab after pressing [ use [ the tabs, and then use [ tab you want.
4] to return to the menu item selection,
8] or [MENU] to move the highlighting up to
4] and [6] to select the
[SET]
[8] [2] [4] [6]
Example: When “Size” is selected on the “Quality” tab
Tabs
Settings
Selected menu item
47
Advanced Settings
NOTE
• [MENU] provides a helpful way to navigate around tabs and menus. – Pressing [MENU] while a tab is selected will display the viewfinder screen. – Pressing [MENU] while menu item or setting is selected will “back step” in the
following sequence: Settings
* Menu items * Tab.
• Depending on the recording mode, some of the items on the menu that appears may not be usable. Only the menu items whose settings can be configured (page
30) will be displayed on the menus while Premium Auto is in use.
. REC Menu Operations in This Manual
REC menu operations are represented in this manual as shown below. The following operation is the same one described under “Example REC Menu Screen Operation” on page 47.
Use [4] and [6] to select the “Quality” tab.
Procedure
Enter the REC Mode * [MENU] * “Quality” Tab * Size
Press
[MENU].
48
Use [8] and [2] to select “Size” and then press [6].
Advanced Settings

REC Mode Settings (REC)

Selecting a Focus Mode (Focus)

Procedure
Enter the REC Mode * [MENU] * “REC” Tab * Focus
Auto Focus is the only focus mode available while Make-up (page 43) or Face Detection (page 50) is enabled. To select another focus mode, first turn off Make-up and Face Detection.
Settings
AF (Auto Focus)
´ Macro
PF (Pan Focus)
Infinity
REC Screen Icon Display
None
Type of Shot
General recording
Close ups
Shooting with a relatively wide focus range
Scenery and other distant subjects
Focus Mode Approximate Focus Range
Snapshot Movies Snapshot Movies
10 cm to 9 (infinity)
Fixed
Automatic
focal point
Fixed focal point
Fixed Infinity (Wide Angle)
2
*
(3.9" to 9)
10 cm to 50 cm (3.9" to 19.7")
1.3 m to 9 (infinity) (4.3' to 9)
10 cm to 9 (infinity) (3.9" to 9)
10 cm to 9 (infinity) (3.9" to 9)
50 cm to 9 (infinity) (19.7" to 9)
*1 The focus range is the distance from the lens surface. *2 The camera focuses on the subject in the center of the screen only once,
immediately after the [0] (Movie) button is pressed. After that, focus remains fixed during recording of the movie.
Using Focus Lock
“Focus lock” is a technique you can use when you want to compose an image in which the subject you want to focus on is not within the focus frame in the center of the screen.
Subject to be focused on
1
*
1. Align the monitor screen’s focus frame with
the subject you want to focus on and then half-press the shutter button.
49
Focus frame
Advanced Settings
2. Keeping the shutter button half-pressed
(which maintains the focus setting), move the camera to compose the image.
3. When you are ready to shoot the image,
press the shutter button the rest of the way down.
NOTE
• Focus lock also locks exposure (AE).
• Certain shooting conditions when you are shooting with AF (Auto Focus) or Macro focus lock may cause the camera to switch automatically to PF (Pan Focus).

Using Face Detection (Face Detection)

Procedure
Enter the REC Mode * [MENU] * “REC” Tab * Face Detection
When shooting people, the face detection feature detects the faces of up to ten individuals and adjusts focus and brightness accordingly.
1. Use [8] and [2] to select “On” and then press [SET].
2. Point the camera at the subject(s).
The camera will detect human faces and display a frame around each one.
3. Half-press the shutter button.
The camera will focus and the frames around the faces it focuses on will turn green.
Face Detection icon
4. Press the shutter button the rest of the way
down.
IMPORTANT!
• The camera performs center focus if it cannot detect a face.
• The only focus mode available while face detection is enabled is Auto Focus (AF).
• Face detection may take a bit longer when you hold the camera sideways.
• Detection of the following types of faces is not supported. – Face that is obstructed by hair, sunglasses, a hat, etc., or a face in dark shade – A profile or a face that is at an angle – A face that is very far away and small, or very close and large – A face in an area that is very dark – The face of a pet or some other non-human subject
• Face detection cannot be used in combination with any of the following features. – Movie Recording
50
Advanced Settings
• Turning on Premium Auto (page 27) or Make-up (page 43) automatically turns on Face Detection.

Using Continuous Shutter (CS)

Procedure
Enter the REC Mode * [MENU] * “REC” Tab * CS
While Continuous Shutter is turned on, images are continually recorded until memory becomes full, as long as you keep the shutter button depressed. Releasing the shutter button stops shooting.
NOTE
• With continuous shutter, exposure and focus for the first image are applied for successive images as well.
• Continuous shutter cannot be used in combination with any of the following. – Premium Auto – Make-up –ART SHOT – Movie Recording –Self-timer
• When using a continuous shutter mode, keep the camera still until all recording is finished.
• The continuous shutter rate depends on the current image size and image quality settings.
• The speed of Continuous Shutter depends on the type of memory card loaded in the camera and the amount of free space available for storage. When shooting to built-in memory, continuous shutter shooting is relatively slow.
51
Advanced Settings

Reducing the Effects of Camera and Subject Movement (Anti Shake)

Procedure
Enter the REC Mode * [MENU] * “REC” Tab * Anti Shake
You can turn on the camera’s Anti Shake feature to reduce image blur due to subject movement or camera movement when shooting a moving subject using telephoto, when shooting a fast-moving subject, or when shooting under dim lighting conditions.
Setting
On
Off None Turns off snapshot Anti Shake.
NOTE
• ISO sensitivity, aperture, and shutter speed do not appear on the monitor screen when you half-press the shutter button while “On” is selected. These values will appear briefly, however, in the preview image that is displayed immediately after you shoot a snapshot.
• The ISO sensitivity setting (page 59) must be “Auto” for Anti Shake to work.
• Shooting with Anti Shake can cause an image to appear somewhat coarser than normal and can cause slight deterioration of image resolution.
• Anti Shake may not be able to eliminate the effects of camera or subject movement when movement is severe.
REC Screen Icon Display
Description
Reduces the effects of hand and subject movement during snapshot recording.
52
Advanced Settings
Assigning Functions to the [4] and [6] Keys (L/R Key)
Procedure
Enter the REC Mode * [MENU] * “REC” Tab * L/R Key
You can assign one of the four functions listed below to the [4] and [6] keys.
Setting [4]/[6] key operation
EV Shift Adjusts the EV shift value (page 56).
White Balance Changes the white balance setting (page 57).
ISO Changes the ISO Sensitivity setting (page 59).
Self-timer
Off Cancels [
* Sets the self-timer time (page 41).
4] and [6] key assignments.
* Triple Self-timer cannot be selected while ART SHOT is the recording mode or
while “On” is selected for “Make-up”. While “On” is selected for Continuous Shutter (CS) or Silent mode, the [4] and [6] keys cannot be used to change the self-timer time.
NOTE
• The “L/R Key” setting cannot be used together with the following feature. – Premium Auto

Displaying the On-screen Grid (Grid)

Procedure
Enter the REC Mode * [MENU] * “REC” Tab * Grid
The on-screen grid can be displayed on the REC mode monitor screen for easy vertical and horizontal alignment when composing images.
53
Advanced Settings

Turning on Image Review (Review)

Procedure
Enter the REC Mode * [MENU] * “REC” Tab * Review
While Review is turned on, the camera will display a image for about one second immediately after you press the shutter button to record it.
• A review image is always displayed when shooting with Continuous Shutter (CS), regardless of the Review setting.
• When shooting with some functions while “On” is selected for “Review” will cause the message “Busy... Please wait...” to appear after you press the shutter button. Shooting another image is disabled while this message is displayed. Wait a while until the process being performed is complete.

Using Icon Help (Icon Help)

Procedure
Enter the REC Mode * [MENU] * “REC” Tab * Icon Help
While Icon Help is turned on, a textual description will appear on the display for certain icons when you switch between REC functions.
Functions Supported by Icon Help
• REC Mode, LED light, White Balance, Self-timer, EV Shift

Selecting Display Information (Information)

Procedure
Enter the REC Mode * [MENU] * “REC” Tab * Information
Selecting “On” displays setup status and other information.
54
Advanced Settings

Image Quality Settings (Quality)

To select the snapshot image size (Size)

Procedure
Enter the REC Mode * [MENU] * “Quality” Tab * Size
Image Size (Pixels)
14M
x
3240)
(4320
3M
x
1536)
(2048
REC Screen Icon Display
Suggested Print Size and Application
Poster Print
3.5"×5" Print
Description
Good detail for better clarity even for images cropped (page 69) from the original
Best when preserving memory capacity is relatively more important than image quality.
• The initial factory default image size setting is “14M”.
• You should regard the print paper sizes suggested here as guidelines only (200 dpi print resolution).
. Pixels and image size
A digital camera image is a collection of small dots called “pixels”. The more pixels there are in an image, the more detail there will be. However, you generally can do with fewer pixels when printing an image (L size) through a print service, attaching an image to e-mail, when viewing the image on a computer, etc. The size of an image indicates how many pixels it contains, and is expressed as
x
horizontal pixels
vertical pixels.
Pixel
Example:
Image size Pixels
x
14M 4320
3M 2048
3240 (Approximately 14 million pixels)
x
1536 (Approximately 3 million pixels)
• Note that larger images have more pixels, so they take up more memory space.
• For information about image size and number of images that can be stored, see page 121.
• For information about movie image size, see page 56.
• For information about resizing existing snapshots, see page 68.
55
Advanced Settings
Specifying Movie Image Quality (» Quality (Movie))
Procedure
Enter the REC Mode * [MENU] * “Quality” Tab * » Quality (Movie)
Movie image quality is a standard that determines the detail, smoothness, and clarity of a movie during playback. Shooting with the high-definition movie (FHD) setting will result in better image quality, but it also shortens the amount of time you can shoot.
Image Quality (Pixels)
FHD 1920
STD 640
• The 16:9 aspect ratio is available when “FHD” is selected as the image quality.
• Memory capacity (Movie recording time you can shoot) will be affected by the quality settings you configure (page 121).
x
x
REC Screen Icon Display
1080 16.6 Megabits/second 30 frames/second
480 8.4 Megabits/second 30 frames/second
Approximate Data Rate
Frame Rate

Correcting Image Brightness (EV Shift)

Procedure
Enter the REC Mode * [MENU] * “Quality” Tab * EV Shift
You can manually adjust an image’s exposure value (EV value) before shooting it.
• Exposure Compensation Range: –2.0 EV to +2.0 EV
• Unit: 1/3 EV
1. Use [8] and [2] to adjust the exposure compensation value.
[8] : Increases the EV value. A higher EV
value is best for light-colored subjects and backlit subjects.
[2] : Decreases the EV value. A lower EV
value is best for dark-color subjects and for shooting outdoors on a clear day.
To cancel exposure compensation, change the EV value to 0.0.
2. Press [SET].
This applies the exposure compensation value. The exposure compensation value you set remains in effect until you change it or turn off the camera (which causes it to revert to “0.0”).
56
Advanced Settings
NOTE
• When shooting under very dark or very bright conditions, you may not be able to obtain satisfactory results even after performing exposure compensation.

Controlling White Balance (White Balance)

Procedure
Enter the REC Mode * [MENU] * “Quality” Tab * White Balance
You can adjust white balance to match the source of light available where you are shooting and avoid the blue cast that results when shooting outdoors when it is cloudy, and the green cast that results when shooting under fluorescent lighting.
Setting
Auto None
(Daylight) For shooting outdoors on a clear day
(Overcast)
(Shade)
(Day White
Fluor)
(Daylight
Fluor)
(Tungsten) For shooting under light bulb lighting
REC Screen Icon Display
Description
Configures the camera to adjust white balance automatically.
For shooting outdoors on an overcast rainy day, in the shade, etc.
For shooting on a clear day in the shade of trees or buildings
For shooting under white or day white fluorescent lighting
For shooting under daylight fluorescent lighting
57
Advanced Settings
Setting
Manual
• When “Auto” is selected for the white balance setting, the camera automatically determines the white point of the subject. Certain subject colors and light source conditions can cause problems when the camera tries to determine the white point, which makes proper white balance adjustment impossible. If this happens, select the white balance setting that matches your shooting conditions (Daylight, Overcast, etc.).
REC Screen Icon Display
Description
For configuring the camera manually to suit a particular light source
Select “Manual”.
1
Under the lighting conditions
2
you plan to use when shooting, point the camera at a blank white piece of paper so it fills the entire monitor screen and then press the shutter button. Press [SET].
3
The white balance setting is retained even if you turn off the camera.
Blank white paper
58
Advanced Settings

Specifying ISO Sensitivity (ISO)

Procedure
Enter the REC Mode * [MENU] * “Quality” Tab * ISO
ISO sensitivity is a measure of sensitivity to light.
Setting
REC Screen Icon Display
Description
Auto None Adjusts sensitivity automatically according to conditions.
ISO 100
Lower
Slow shutter speed
Less noise
sensitivity
ISO 200
ISO 400
ISO 800
ISO 1600
ISO 3200
Higher sensitivity
Fast shutter speed (Set for shooting in dimly lit areas.)
Some coarseness (increased digital noise)
• “Auto” ISO sensitivity always is applied for movies, regardless of the current ISO sensitivity setting.
• Higher ISO sensitivity values tend to result in digital noise in images.
59
Advanced Settings

Optimizing Image Brightness (Lighting)

Procedure
Enter the REC Mode * [MENU] * “Quality” Tab * Lighting
You can use this setting to optimize the balance between bright areas and dark areas when shooting images.
Setting
On
Off None Does not perform brightness correction.
NOTE
• Lighting is disabled during movie recording.
REC Screen Icon Display
Description
Performs brightness correction. When this option is selected, it takes longer for the image to be stored after the shutter button is pressed.

Using Built-in Color Filters (Color Filter)

Procedure
Enter the REC Mode * [MENU] * “Quality” Tab * Color Filter
Settings: Off, B/W, Sepia, Red, Green, Blue, Yellow, Pink, Purple
• You cannot configure a color filter setting while using ART SHOT (page 36) as the recording mode.
60
Advanced Settings

Viewing Snapshots and Movies

Viewing Snapshots

See page 31 for the procedure for viewing snapshots.

Viewing a Movie

1. Press [p] (PLAY) and then use [4] and [6] to display the movie you
want to view.
2. Press [0] (Movie) to start
Movie icon: »
playback.
Recording time
Image quality
Movie Playback Controls
Fast forward/ fast reverse
Play/pause [SET]
1 frame forward/ back
Volume adjustment
Stop playback [0] (Movie)
NOTE
• Playback may not be possible for movies not recorded with this camera.
[4] [6]
• Each press of either button increases the speed of the fast forward or fast reverse operation.
• To return to normal playback speed, press [SET].
[4] [6]
• Holding down either button scrolls continuously.
Press [2] and then press [8] [2].
• Volume can be adjusted only while movie playback is in progress.
61
Viewing Snapshots and Movies

Zooming an On-screen Snapshot

1. In the PLAY mode, use [4] and [6] to scroll through the images until
the one you want is displayed.
2. Press [8] to zoom.
• While an image is enlarged, press [2] to decrease
the zoom factor.
• While an image is zoomed on the monitor screen,
you can press [MENU] and then use [8], [2], [4], and [6] to scroll the image. Pressing [MENU] again returns to the zoom screen. – When monitor screen contents are turned on,
a graphic in the lower right corner of the screen shows what part of the zoomed image is currently displayed.
– To exit the zoom screen, press [0] (Movie). – Though the maximum image zoom factor is 8X,
certain image sizes may not allow zooming up to the full 8X.

Displaying the Image Menu

1. In the PLAY mode, press [2].
Use [8], [2], [4] and [6] to move the selection boundary around the image menu. To view a particular image, use [8], [2], [4], or [6] to move the selection boundary to the image you want and then press [SET].
• A question mark (?) will be displayed for images that cannot be displayed for some reason.
• Depending on the types of images that are stored, it may take a little time for the image menu to appear.
Zoom factor
Image area
Current display area
Boundary
62
Viewing Snapshots and Movies

Other Playback Functions (PLAY)

This section explains menu items that you can use to configure settings and perform other playback operations.

Using the PLAY Panel

Pressing [SET] in the PLAY mode will display the PLAY Panel.
. Example PLAY Panel Operation
1. In the PLAY mode, press [SET].
The PLAY Panel will appear along the right side of the monitor screen.
PLAY Panel[SET]
2. Use [8] and [2] to select the
PLAY Panel item you want, and then press [SET].
[8] [2]
3. The following describes the operations you can perform for each of the
PLAY Panel items.
Exit Exits the PLAY Panel.
Art
Effect
Silent
Slideshow
Delete Deletes images (page 32).
You can apply artistic effects to recorded snapshots and save the result as a new snapshot. The original snapshot is also retained. For information setting items, see page 36.
The Silent mode turns off camera operation sounds so you can avoid disturbing others around you when playing back images (page 42).
Displays a slideshow menu. See “Playing a Slideshow on the Camera (Slideshow)” (page 64) for slideshow menu operations.
63
Other Playback Functions (PLAY)

Performing Playback without Disturbing Others (Silent)

The Silent mode turns off camera operation sounds so you can avoid disturbing others around you when play back images.
1. In the PLAY mode, press [SET].
2. Use [8] and [2] to select the “Silent” PLAY Panel option and then
press [SET] (page 63).
3. Use [8] and [2] to select “On” and then press [SET].
This enters the Silent mode, which is indicated by m on the monitor screen. The “Sounds” setting (page 89) automatically changes to “Off” in the Silent mode.
• Entering the Silent mode in the PLAY mode will also enter the Silent mode in the REC mode automatically (page 42).

Playing a Slideshow on the Camera (Slideshow)

1. In the PLAY mode, press [SET].
2. Use [8] and [2] to select the “Slideshow” PLAY Panel option and then
press [SET] (page 63).
Start Starts the slideshow.
Time
Interval
Effect
Time from the start to the end of the slideshow 1 to 5 minutes, 10 minutes, 15 minutes, 30 minutes, 60 minutes
Amount of time each image remains displayed Use [4] and [6] to select a value from 1 to 30 seconds, or “MAX”. If you specify a value, movies play from beginning to end. When the slideshow reaches a movie file while “MAX” is selected, only the first frame of the movie will displayed.
Turns effect on or off. On: Turns on the image change effect and background music. Off: No image change effect or background music
• To stop the slideshow, press [MENU]. Pressing [SET] instead of [MENU] stops the slideshow and returns to the menu screen.
• Adjust audio volume by pressing [2] and then press [8] or [2] during playback.
• All button operations are disabled while the slideshow is transitioning from one image to another.
• The time required for transition from one image to another may be longer in the case of an image that was not recorded with this camera.
64
Other Playback Functions (PLAY)

Inserting a Built-in Subject into a Snapshot (Paste subject)

Procedure
[p] (PLAY) * [MENU] * “PLAY” Tab * Paste subject
Use the following procedure to insert a built-in subject image into a snapshot.
1. Use [4] and [6] to select the background image you want and then
press [SET].
• Only an image that satisfies the following conditions can be used as a background image. – A snapshot recorded with this camera – A snapshot with an aspect ratio of 4:3
2. Use [4] and [6] to select the built-in subject that you want to insert
into the image and then press [SET].
3. Use [8] and [2] to adjust the size of the subject.
4. Press [MENU].
5. Use [8], [2], [4], and [6] to adjust its position.
• Pressing [MENU] again returns to the subject size adjustment screen in step 3.
6. After the subject’s size and position are the way you want, press [SET].
This merges the subject and the background image and saves the result as a new 6M (2816
NOTE
• Performing a delete or format operation will not delete the built-in subjects.
• There will be some deterioration in the quality of an image created by the above operation.
x
2112) image.
65
Other Playback Functions (PLAY)

Blurring a Playback Image (Blur Effect)

Procedure
[p] (PLAY) * Snapshot Screen * [MENU] * “PLAY” Tab * Blur Effect
1. Use [8], [2], [4], and [6] to select the center
of the circle to define the area to be left unblurred, and then press [MENU].
2. Use [8] and [2] to change the size of the
circle.
• The blur effect will be applied to the part of the image outside the circle.
• To return to step 1 and select a different center point, press [MENU] again.
3. After selecting the center point and the size of the unblurred area,
press [SET].
4. Use [8] and [2] to select the blur level you want, and then press
[SET].
This will apply the blur effect and save the result as a new image.

Auto Image Orientation Detection and Rotation (Auto Rotate)

Procedure
[p] (PLAY) * [MENU] * “PLAY” Tab * Auto Rotate
On
Off Images not rotated automatically.
This setting can be used to configure the camera to display playback images in the same orientation as the camera when the image was shot.
• Auto image rotation will not be performed during movie playback, while the image menu is displayed, and for some functions.
Rotates the displayed image in accordance with the camera orientation when the image was recorded.
66
Other Playback Functions (PLAY)

Rotating an Image (Rotation)

Procedure
[p] (PLAY) * Snapshot Screen * [MENU] * “PLAY” Tab * Rotation
1. Use [8] and [2] to select “Rotation” and then press [SET].
Each press of [SET] will rotate the displayed image 90 degrees left.
2. When the displayed image is at the orientation you want, press
[MENU].
NOTE
• Note that this procedure does not actually change the image data. It simply alters how the image is displayed on the camera’s monitor screen.
• An image that has been protected or zoomed cannot be rotated.
• The original (unrotated) version of the image will be displayed on the image menu screen.

Selecting Images for Printing (DPOF Printing)

Procedure
[p] (PLAY) * Snapshot Screen * [MENU] * “PLAY” Tab * DPOF Printing
See page 75 for details.
67
Other Playback Functions (PLAY)

Protecting a File Against Deletion (Protect)

Procedure
[p] (PLAY) * [MENU] * “PLAY” Tab * Protect
Protects specific files.
Use [4] and [6] to scroll through the files
1
until the one you want to protect is displayed. Use [8] and [2] to select “On” and then
On
All Files: On
IMPORTANT!
• Note that even if a file is protected, it will be deleted if you perform the format operation (page 95).
2
press [SET]. An image that is protected is indicated by the icon. To protect other files, repeat steps 1 and 2.
3
To exit the protect operation, press [MENU]. To unprotect a file, select “Off” instead of “On” in step 2 above.
Protects all files.
Use [8] and [2] to select “All Files: On” and then press [SET].
1
Press [MENU].
2
To unprotect all files, select “All Files: Off” instead of “All Files: On” in step 1 above.

Resizing a Snapshot (Resize)

Procedure
[p] (PLAY) * Snapshot Screen * [MENU] * “PLAY” Tab * Resize
You can reduce the size of a snapshot and save the result as a separate snapshot. The original snapshot is also retained. You can select resize an image to one of three image sizes: 10M, 5M, VGA.
• Resizing a snapshot will create an image with an aspect ratio of 4:3.
• The recording date of the resized version of the snapshot will be the same as the recording date of the original snapshot.
68
Other Playback Functions (PLAY)

Cropping a Snapshot (Trimming)

Procedure
[p] (PLAY) * Snapshot Screen * [MENU] * “PLAY” Tab * Trimming
You can crop a snapshot to trim parts you do not need, and save the result in a separate file. The original snapshot is also retained.
Zoom factor
Represents
snapshot area
1. Use [8] and [2] to zoom the image to the size
you want.
2. Press [MENU].
3. Use [8], [2], [4], and [6] to select the area you
want to extract.
• Pressing [MENU] again returns to the zoom screen in step 1.
Part of snapshot that is
currently displayed
4. After you display area you want to extract, press
[SET].
• The image produced by a trimming operation will have an aspect ratio of 4:3.
• The recording date of the cropped image will be the same as the recording date of the original snapshot.
69
Other Playback Functions (PLAY)

Copying Files (Copy)

Procedure
[p] (PLAY) * [MENU] * “PLAY” Tab * Copy
Files can be copied from the camera’s built-in memory to a memory card or from a memory card to built-in memory.
Built-in * Card
Card * Built-in
NOTE
• You can copy snapshots or movies you recorded with this camera.
Copies all files from built-in camera memory to a memory card. This option copies all the files in built-in camera memory. It cannot be used to copy a single file.
Copies a single file on the memory card to camera built-in camera memory. Files are copied to the folder in built-in memory whose name has the largest serial number.
Use [4] and [6] to select the file you want to copy.
1
Use [8] and [2] to select “Copy” and then press [SET].
2

Selecting Display Information (Information)

Procedure
[p] (PLAY) * [MENU] * “PLAY” Tab * Information
Selecting “On” displays settings when shooting, current date and time, and other information.
70
Other Playback Functions (PLAY)

Connecting the Camera with a Smartphone (Wireless LAN)

Establishing a Connection between a Smartphone and Your Camera

After installing EXILIM Link on a smartphone (or tablet computer) you can select snapshot and/or movie files in camera memory and send them to a smartphone. You can select up to 99 files, totaling no more than 1500MB, for a single send.
• Search the EXILIM Link app on Google Play (Android) or App Store (iOS) and install it on your smartphone (or tablet computer).
IMPORTANT!
• Never use wireless LAN functions inside an aircraft or anywhere else where such operation is restricted.
NOTE
• Note that using wireless LAN functions requires more battery power usage than normal. Make sure that the camera battery is sufficiently charged before starting a wireless LAN operation.
• The operating range depends on the local communication environment and on the type of smartphone you are connected to.
. App operation guarantees
No guarantees are made concerning the ability to operate the EXILIM Link app on any particular smartphone or tablet.
IMPORTANT!
• For information about operating system version supported by the app, check the information on Google Play or the App Store.
• App functions and the required operating environment are subject to change without notice.
Connecting the Camera with a Smartphone (Wireless
71
LAN)

Installing the EXILIM Link App on Your Smartphone

. Android terminal
1. Open “Google Play”.
2. In the search field, type “EXILIM Link”.
3. Install EXILIM Link.
. iPhone
1. Open “App Store”.
2. In the search field, type “EXILIM Link”.
3. Install EXILIM Link.

Sending a Snapshot or Movie File from Camera Memory to a Smartphone

1. Turn on the camera, and then press [ ] (Wi-Fi).
2. For the smartphone Wi-Fi setting, input the
camera SSID and password.
This will connect the smartphone to the camera.
• The password can be changed using “WLAN password” (page 88).
• What you need to do to establish a wireless LAN connection depends on the type of smartphone you are using. For details about how to establish a wireless LAN connection see the user documentation that comes with your smartphone.
SSID
Password
3. On your smartphone, start up the EXILIM Link app.
4. On the smartphone, tap “Connection Starting”.
The smartphone display shows a list of images stored in camera memory.
• If this is the first time you started up the app, its terms of use will appear on the smartphone screen. Read the terms and then tap “Agree”.
5. Tap the images of the files you want to have sent to the smartphone.
6. After selecting the images of all of the files you want to send to the
smartphone, touch “ ”.
This will send the images you selected to the smartphone. You can view the sent images with “ ”.
Connecting the Camera with a Smartphone (Wireless
72
LAN)
IMPORTANT!
• Some smartphone models may not be able to play back movie files.
• Depending on your smartphone model, its operating system version, and/or its remaining storage capacity can cause failure of a movie or snapshot save operation. After send operation, perform the required operation on your smartphone to ensure that the movie or snapshot was saved properly.
• Viewing a movie received on an Android terminal: Note that movies are not displayed by Gallery. Movies are stored in a folder named “EXILIM Link”. A separate movie player is required to playback movies (whose files have the file name extension MOV). Depending on your movie player, you may not be able to playback movies and/or audio.
• Note that the wireless LAN connection between the camera and smartphone is maintained even while the EXILIM Link app is not running on the smartphone or when the app is running in the background. Leaving a wireless LAN connection in effect will shorten camera battery life and cause the camera to become warm. Shut down the EXILIM Link app and turn off the camera to terminate the wireless LAN connection whenever you are not using it.
• Using the smartphone’s Wi-Fi setting screen to terminate a wireless LAN connection will cause the camera to enter connection standby. If no connection is established within three minutes, the camera will return to the state it was in before the LAN connection was established.
NOTE
• Note that after changing the wireless LAN password on the camera, you will also need to change the Wi-Fi settings of the smartphone. – iPhone:
Tap the right arrow of the field where the SSID of the camera is displayed in the Wi-Fi settings to delete network settings. After deleting, select the camera SSID again and input the new password.
– Android terminal:
Tap the field where the SSID of the camera is displayed in the Wi-Fi settings and select Forget. Select the camera SSID again and input the new password.
Connecting the Camera with a Smartphone (Wireless
73
LAN)

Resizing Snapshots before Sending Them to a Smartphone (Resize before send)

Procedure
[MENU] * “Set Up” Tab * Resize before send
This feature can be use to resize snapshots before they are sent to a smartphone using EXILIM Link.
3M
• If an original image is 3M size or smaller, it is sent without resizing.
Off Images are sent in the size they were originally recorded.
Images are converted to 3M size before being sent.
Connecting the Camera with a Smartphone (Wireless
74
LAN)

Printing

Printing Snapshots

Professional Print Service*
You can take a memory card that contains the images you want to print to a professional print service and have them printed.
Printing on a Home Printer*
You can use a printer equipped with a memory card slot to print images directly from a memory card. For details, see the user documentation that comes with your printer.
Printing with a Computer
After transferring the images to your computer, use commercially available software to print.
* You can specify which images you want to print, the number of copies, and date
stamp settings before printing (page 75).

Using DPOF to Specify Images to be Printed and the Number of Copies

. Digital Print Order Format (DPOF)
DPOF is a standard that allows you to include image type, number of copy, and time stamp on/off information on the memory card with the images. After configuring settings, you can use the memory card to print on a home printer that supports DPOF or take the memory card to a professional print service.
• Whether or not you will be able to use DPOF settings for printing depends on the printer you are using.
• Some professional print services may not support DPOF.
75
Printing
. Configuring DPOF Settings Individually for Each Image
Procedure
[p] (PLAY) * Snapshot Screen * [MENU] * “PLAY” Tab * DPOF Printing * Select images
1. Use [4] and [6] to scroll through the files until the image you want to
print is displayed.
2. Use [8] and [2] to specify the number of copies.
You can specify a value up to 99. Specify 00 if you do not want to print the image.
• If you want to include the date in the images, press [0] (Movie) so “Date
stamping On” is shown for date stamping.
• Repeat steps 1 and 2 to configure settings for other images, if you want.
3. Press [SET].
. Configuring the Same DPOF Settings for All the Images
Procedure
[p] (PLAY) * Snapshot Screen * [MENU] * “PLAY” Tab * DPOF Printing * All images
1. Use [8] and [2] to specify the number of copies.
You can specify a value up to 99. Specify 00 if you do not want to print the image.
• If you want to include the date in the images, press [0] (Movie) so “Date
stamping On” is shown for date stamping.
2. Press [SET].
DPOF settings are not cleared automatically after printing is complete.
The next DPOF print operation you execute will be performed using the last DPOF settings you configured for the images. To clear DPOF settings, specify “00” for the number of copies of all images.
Tell your print service about your DPOF settings!
If you take a memory card to a professional print service, be sure to tell them that it includes DPOF settings for the images to be printed and the number of copies. If you don’t, the print service may print all the images without regard to your DPOF settings, or they may ignore your date stamp setting.
76
Printing
. Date Stamping
You can use one of the following three methods to include the recording date in the printout of an image.
Configuring camera settings
Configure DPOF settings (page 75). You can turn date stamping on and off each time you print. You can configure settings so some images include the date stamp and some don’t.
Configure the Camera’s Time Stamp setting (page 91).
• The camera’s Time Stamp setting imprints the date into a snapshot when you shoot it, so the date is always included when you print. It cannot be deleted.
• Do not turn on DPOF date stamping for an image that includes a date stamped with the camera’s Time Stamp function. Doing so can cause the two stamps to be overprinted.
Configuring computer settings
You can use commercially available image management software to date stamp images.
Professional print service
Request date stamping when ordering prints from a professional print service.
. Standards Supported by the Camera
•Exif Print Printing on a printer that supports Exif Print uses information about shooting conditions recorded with the image to enhance printed image quality. Contact your printer manufacturer for information about models that support Exif Print, printer upgrades, etc.
77
Printing

Using the Camera with a Computer

Things you can do using a computer...

You can perform the operations described below while the camera is connected to a computer.
Save images to a computer and view them there
Play back and edit movies
The procedures you need to perform are different for Windows and the Macintosh.
• Windows users should refer to “Using the Camera with a Windows Computer” on page 79.
• Macintosh users should refer to “Using the Camera with a Macintosh” on page
83.
• Save images and view them manually (USB connection) (pages 79, 83).
• You can play back movies (pages 82, 85).
• To edit movies, use commercially available software as required.
78
Using the Camera with a Computer

Using the Camera with a Windows Computer

When you want to do this:
Save images to a computer and view them there manually
Play movies
Operating System Version
Windows 8.1, Windows 8, Windows 7, Windows Vista
Windows 8.1, Windows 8, Windows 7, Windows Vista
Required Software
Installation not required. 79
QuickTime 7 or higher
• You need to download QuickTime 7 on the Web if you want to use it.
See page:
82

Viewing and Storing Images on a Computer

You can connect the camera to your computer in order to view and store images (snapshot and movie files).
Never use your computer to modify, delete, move, or rename any image files that are in the camera’s built-in memory or on its memory card.
Doing so can cause problems with the camera’s image management data, which will make it impossible to play back images on the camera and can drastically alter remaining memory capacity. Whenever you want to modify, delete, move, or rename an image, do so only on images that are stored on your computer.
IMPORTANT!
• Never unplug the USB cable, or operate the camera while viewing or storing images. Doing so can cause data to become corrupted.
NOTE
• You also can use your computer’s card slot (if it has one) or a commercially available card reader to access image files directly from the camera’s memory card. For details, see the user documentation that comes with your computer.
79
Using the Camera with a Computer
. To connect the camera to your computer and save files
1. Turn off the camera and
then use the micro USB cable that comes with the camera to connect it to your computer.
• For details about connecting to the camera and precautions when connecting, see page 19.
Micro USB cable
(included with camera)
USB port
2. Press [p] (Power) to turn on the camera.
When you turn on the camera, check to make sure that the color of its back lamp changes from red to green or amber (page 20).
• The first time you connect the camera to your computer with the USB cable, an error message may appear on your computer. If this happens, disconnect and then reconnect the USB cable.
• Charging continues even if the camera is turned on.
3. Windows 8.1, Windows 8 users: Click “Desktop” and then “Explorer”.
Windows 7, Windows Vista users: Click “Start” and then “Computer”.
4. Double-click “Removable Disk”.
• Your computer recognizes the memory card loaded in the camera (or built-in memory if there is no card) as a removable disk.
5. Right-click the “DCIM” folder.
6. On the shortcut menu that appears, click “Copy”.
7. Windows 8.1, Windows 8 users: Click “Documents”.
Windows 7, Windows Vista users: Click “Start” and then “Documents”.
• If you already have a “DCIM” folder in “Documents”, the next step will overwrite it. If you want to keep the existing “DCIM” folder, you need to change its name or move it to a different location before performing the next step.
80
Using the Camera with a Computer
8. Windows 8.1, Windows 8 users: On the “Documents” menus, click
“Home” and then “Paste”. Windows 7, Windows Vista users: On the “Documents” menu, click “Organize” or “Edit”, and then “Paste”.
This will paste the “DCIM” folder (and all the image files it contains) into your “Documents” folder. You now have a copy of the files that are in camera memory on your computer.
9. After you finish copying images, disconnect the camera from the
computer.
After confirming that the back lamp is not flashing red, disconnect the USB cable.
. To view images you copied to your computer
1. Double-click the copied “DCIM” folder to open it.
2. Double-click the folder that contains the images you want to view.
3. Double-click the image file you want to view.
• For information about file names, see “Memory Folder Structure” on page 87.
• An image that was rotated on the camera will be displayed on your computer screen in its original (unrotated) orientation.
• Viewing CS images on a computer will individually display the component images in the group. CS images cannot be viewed as a group on a computer.
81
Using the Camera with a Computer

Playing Movies

To play back a movie, first copy it to your computer and then double-click the movie file. Some operating systems may not be able to play back movies. If this happens, you need to install separately available software.
• If you are unable to play back movies, go to the URL below to download QuickTime 7 and install it on your computer. http://www.apple.com/quicktime/
. Minimum Computer System Requirements for Movie Playback
The minimum system requirements described below are necessary to play back movies recorded with this camera on a computer.
Operating System : Windows 8.1, Windows 8, Windows 7, Windows Vista CPU : Image Quality “FHD”:
Required Software: QuickTime 7 or higher
• The above are recommended system environments. Configuring one of these environments does not guarantee proper operation.
• Certain settings and other installed software may interfere with proper playback of movies.
Core 2 Duo 3.0 GHz or higher
Image Quality “STD”:
Pentium 4 3.2 GHz or higher
. Movie Playback Precautions
• Be sure to move the movie data to the hard disk of your computer before trying to play it. Proper movie playback may not be possible for data accessed over a network, from a memory card, etc.
• Proper movie playback may not be possible on some computers. If you experience problems, try the following. – Try recording movies with a quality setting of “STD”. – Quit any other applications you have running, and stop resident applications.
82
Using the Camera with a Computer

Using the Camera with a Macintosh

When you want to do this:
Save images to your Macintosh and view them there manually
Save images to your Macintosh automatically/Manage images
Play movies
Operating System Version
OS X Installation not required. 83
OS X
OS X 10.5 or higher
Required Software
iPhoto, which comes bundled with some Macintosh products.
QuickTime Player (installed on computer)
See page:
85

Connecting the Camera to Your Computer and Saving Files

Never use your computer to modify, delete, move, or rename any image files that are in the camera’s built-in memory or on its memory card.
Doing so can cause problems with the camera’s image management data, which will make it impossible to play back images on the camera and can drastically alter remaining memory capacity. Whenever you want to modify, delete, move, or rename an image, do so only on images that are stored on your computer.
IMPORTANT!
• Never unplug the USB cable, or operate the camera while viewing or storing images. Doing so can cause data to become corrupted.
• The camera does not support operation with Mac OS X 10.0 to 10.4. Operation is supported with Mac OS 10.5 to 10.9 (using the OS standard USB driver) only.
NOTE
• You also can use your computer’s card slot (if it has one) or a commercially available card reader to access image files directly from the camera’s memory card. For details, see the user documentation that comes with your computer.
83
Using the Camera with a Computer
. To connect the camera to your computer and save files
1. Turn off the camera and
then use the micro USB cable that comes with the camera to connect it to your Macintosh.
• For details about connecting to the camera and precautions when connecting, see page 19.
Micro USB cable
(included with camera)
USB port
2. Press [p] (Power) to turn on the camera.
When you turn on the camera, check to make sure that the color of its back lamp changes from red to green or amber (page 20). In this mode, your Macintosh recognizes the memory card loaded in the camera (or the camera’s built-in memory if it does not have a memory card loaded) as a drive. The appearance of the drive icon depends on the Mac OS version you are using.
• The first time you connect the camera to your Macintosh with the USB cable, an error message may appear on your computer. If this happens, disconnect and then reconnect the USB cable.
• Charging continues even if the camera is turned on.
3. Double-click the camera’s drive icon.
4. Drag the “DCIM” folder to the folder to which you want to copy it.
5. After the copy operation is complete, drag the drive icon to Trash.
6. Disconnect the camera from the computer.
After confirming that the back lamp is not flashing red, disconnect the USB cable.
84
Using the Camera with a Computer
. To view copied images
1. Double-click the camera’s drive icon.
2. Double-click the “DCIM” folder to open it.
3. Double-click the folder that contains the images you want to view.
4. Double-click the image file you want to view.
• For information about file names, see “Memory Folder Structure” on page 87.
• An image that was rotated on the camera will be displayed on your Macintosh screen in its original (unrotated) orientation.

Playing a Movie

To play back a movie, first copy it to your Macintosh and then double-click the movie file.
. Minimum Computer System Requirements for Movie Playback
The minimum system requirements described below are necessary to play back movies recorded with this camera on a computer.
Operating System : Mac OS X 10.5 or higher Required Software: QuickTime Player (installed on computer)
• The above are recommended system environments. Configuring one of these environments does not guarantee proper operation.
• Certain settings and other installed software may interfere with proper playback of movies.
. Movie Playback Precautions
Proper movie playback may not be possible on some Macintosh models. If you experience problems, try the following.
– Change the movie image quality setting to “STD”. – Shut down other applications that are running.
IMPORTANT!
• Be sure to move the movie data to the hard disk of your Macintosh before trying to play it. Proper movie playback may not be possible for data accessed over a network, from a memory card, etc.
85
Using the Camera with a Computer

Files and Folders

The camera creates a file and saves it each time you shoot a snapshot, record a movie, or perform any other operation that stores data. Files are grouped by storing them in folders. Each file and folder has its own unique name.
• For details about how folders are organized in memory, see “Memory Folder Structure” (page 87).
Name and Maximum Number Allowed Example
File
Each folder can contain up to 9999 files named CIMG0001 through CIMG9999. The extension on the file name depends on the file type.
Folders
Folders are named from 100CASIO to 999CASIO. There can be up to 900 folders in memory.
• You can view folder and file names on your computer. For details about how file names are displayed on the camera’s monitor screen, see page 11.
• The total number of folders and files allowed depends on the image size and quality, and capacity of the memory card being used for storage.
26th file name:
CIMG0026.JPG
Extension
Serial number (4 digits)
100th folder name:
100CASIO
Serial number (3 digits)
86
Using the Camera with a Computer

Memory Card Data

The camera stores images you shoot in accordance with the Design Rule for Camera File System (DCF).
. About DCF
The following operations are supported for DCF-compliant images. Note, however, that CASIO makes no performance guarantees concerning these operations.
• Transferring this camera’s DCF-compliant images to another manufacturer’s camera and view them.
• Printing this camera’s DCF-compliant images on another manufacturer’s printer.
• Transferring another camera’s DCF-compliant images to this camera and view them.
. Memory Folder Structure
DCIM
100CASIO CIMG0001.JPG CIMG0002.MOV
101CASIO 102CASIO
MISC
AUTPRINT.MRK
. Supported Image Files
• Image files shot with this camera
• DCF-compliant image files
This camera may not be able to display an image, even if it is DCF-compliant. When displaying an image recorded on another camera, it may take a long time for the image to appear on this camera’s monitor screen.
DCIM Folder Recording Folder Image File Movie File
Recording Folder Recording Folder
DPOF File Folder DPOF File
. Built-in Memory and Memory Card Data Handling Precautions
• Whenever copying memory contents to your computer, you should copy the DCIM folder and all of its contents. A good way to keep track of multiple DCIM copies of the DCIM folders is to change its name to a date or something similar after you copy it to your computer. If you later decided to return the folder to the camera, however, be sure to change its name back to DCIM. The camera is designed to recognize only a root file with the name DCIM. Note the camera also will not be able to recognize the folders inside the DCIM folder unless they have the names they originally had when you copied them from the camera to your computer.
• Folders and files must be stored in accordance with the “Memory Folder Structure” shown on page 87 in order for the camera to be able to recognize them correctly.
87
Using the Camera with a Computer

Other Settings (Set Up)

This section explains menu items that you can use to configure settings and perform other operations in both the REC mode and PLAY mode.
See the following for more information.
– REC Menu (page 47) – PLAY Menu (page 63)

Changing the Menu Screen Color (Menu Color)

Procedure
[MENU] * “Set Up” Tab * Menu Color
Use this procedure to select black, pink, or white as the menu color on the monitor screen.
• The text color will also change in accordance with the menu color.

Resizing Snapshots before Sending Them to a Smartphone (Resize before send)

Procedure
[MENU] * “Set Up” Tab * Resize before send
See page 74 for details.

Changing the Camera Password for Wireless LAN Connection (WLAN password)

Procedure
[MENU] * “Set Up” Tab * WLAN password
Use procedure to change the password you used when establishing a wireless LAN connection between the camera and a smartphone.
1. Use [4] and [6] to move the cursor to the password digit you want to
change.
2. Use [8] and [2] to change the currently selected digit.
3. When the password is the way you want, move the cursor to “Apply”
and then press [SET]
88
Other Settings (Set Up)

Configuring Camera Sound Settings (Sounds)

Procedure
[MENU] * “Set Up” Tab * Sounds
Startup
Half Shutter
Shutter
Operation
Operation Specifies the sound volume.
Play Specifies the volume of movie audio output.
• Setting a volume level of 0 mutes output.
Specifies the startup sound. Sound 1 - 5: Built-in sounds (1 through 5) Off: Sound off

Configuring a Startup Image (Startup)

Procedure
[MENU] * “Set Up” Tab * Startup
Display the image you want to use as your startup image and then select “On”.
• The startup image does not appear when you turn on the camera by pressing [p] (PLAY).
• You can specify a snapshot you recorded as the startup image, or you can use the special startup image provided in the camera’s built-in memory.
• Formatting built-in memory (page 95) will delete the current startup image setting.
89
Other Settings (Set Up)

Specifying the File Name Serial Number Generation Rule (File No.)

Procedure
[MENU] * “Set Up” Tab * File No.
Use the following procedure to specify the rule that governs generation of the serial number used in file names (page 86).
Tells the camera to remember the last used file number. A new file will be named using the next sequential number, even if files are deleted or
Continue
Reset
if a blank memory card is loaded. If a memory card is loaded and that card already has files stored on it and the largest sequential number in the existing file names is greater than the largest sequential number remembered by the camera, numbering of new files will start from the largest sequential number in the existing file names plus 1.
Restarts the serial number from 0001 whenever all files are deleted or when the memory card is replaced with a blank one. If a memory card is loaded and that card already has files stored on it, numbering of new files will start from the largest sequential number in the existing file names number plus 1.

Configuring World Time Settings (World Time)

Procedure
[MENU] * “Set Up” Tab * World Time
You can use the World Time screen to view the current time in a zone that is different from your Home City when you go on a trip, etc. World Time displays the current time in 162 cities in 32 time zones around the globe.
1. Use [8] and [2] to select “Destination” and then press [6].
• To change the geographic area and city for the time where you normally use the camera, select “Home”.
2. Use [8] and [2] to select “City” and then press [6].
• To change the “Destination” setting to summer time, use [8] and [2] to select “DST” and then select “On”. Summer time is used in some geographical areas to advance the current time setting by one hour during the summer months.
3. Use [8], [2], [4], and [6] to select the geographic area you want and
then press [SET].
4. Use [8] and [2] to select the city you want and then press [SET].
5. Press [SET].
90
Other Settings (Set Up)
IMPORTANT!
• Before configuring World Time settings, make sure that the Home City setting is the place where you live or normally use the camera. If it isn’t, select “Home” on the screen in step 1 and configure the Home City, date, and time settings as required (page 92).

Time Stamping Snapshots (Timestamp)

Procedure
[MENU] * “Set Up” Tab * Timestamp
You can configure the camera to stamp the recording date only, or date and time in the lower right corner of each snapshot.
Example: July, 10, 2016, 1:25 p.m.
Date 2016/7/10
Date & Time 2016/7/10 1:25pm
Off No stamping of date and/or time
• Once date and time information is stamped into a snapshot, it cannot be edited or deleted.
• Even if you do not stamp the date and/or time with Timestamp, you can do so later using the DPOF function or some printing application (page 77).
91
Other Settings (Set Up)

Setting the Camera’s Clock (Adjust)

Procedure
[MENU] * “Set Up” Tab * Adjust
[8] [2] Change the setting at the cursor location
[4] [6] Move the cursor between settings
[0] (Movie) Toggles between 12-hour and 24-hour format
When the date and time settings are what you want, press [SET] to apply them.
• You can specify a date from 2001 to 2049.
• Be sure to select your Home City (page 90) before setting the time and date. If you set the time and date while the wrong city is selected for your Home City, the times and dates of all of the World Time cities (page 90) will be wrong.

Specifying the Date Style (Date Style)

Procedure
[MENU] * “Set Up” Tab * Date Style
You can select from among three different styles for the date.
Example: July, 10, 2016
YY/MM/DD 16/7/10
DD/MM/YY 10/7/16
MM/DD/YY 7/10/16
92
Other Settings (Set Up)

Specifying the Display Language (Language)

Procedure
[MENU] * “Set Up” Tab * Language
. Specify the display language you want.
Select the tab on the right.
1
Select “Language”.
2
Select the language you want.
3
• Camera models sold in certain geographic areas may not support display language selection.
1
23

Configuring Sleep State Settings (Sleep)

Procedure
[MENU] * “Set Up” Tab * Sleep
This feature turns off the monitor screen and lights the back lamp (green) whenever no camera operation is performed for a preset period of time. Press any button to turn the monitor screen back on.
Trigger Time Settings: 30 sec, 1 min, 2 min, Off (Sleep is disabled while “Off” is selected.)
• Sleep is disabled under any of the following conditions. – In the PLAY mode – While the camera is connected to a computer or other device – During movie recording and playback
• When both sleep and Auto Power Off are turned on, Auto Power Off takes priority.
93
Other Settings (Set Up)

Configuring Auto Power Settings (Auto Power Off)

Procedure
[MENU] * “Set Up” Tab * Auto Power Off
Auto Power Off turns off the camera whenever no camera operation is performed for a preset amount of time.
Trigger Time Settings: 1 min, 2 min, 5 min (The trigger time is always 5 minutes in the PLAY mode.)
• Auto Power Off is disabled under any of the following conditions. – While the camera is connected to a computer or other device – During a slideshow – During movie recording and playback
Configuring [p] Setting (PLAY)
Procedure
[MENU] * “Set Up” Tab * PLAY
Power On Camera turns on whenever [p] (PLAY) is pressed.
On/Off Camera turns on or off whenever [p] (PLAY) is pressed.
Disable
• With “On/Off”, the camera turns off when you press [p] (PLAY) in the PLAY mode.
• When “Power On” or “On/Off” is enabled, you can turn on the camera by holding
p] (PLAY) until the back lamp lights green momentarily.
down [
Camera does not turn on or off whenever [ pressed.
p] (PLAY) is
94
Other Settings (Set Up)

Formatting Built-in Memory or a Memory Card (Format)

Procedure
[MENU] * “Set Up” Tab * Format
If a memory card is loaded in the camera, this operation will format the memory card. It will format built-in memory if no memory card is loaded.
• The format operation will delete all contents on the memory card or in built-in memory. It cannot be undone. Make sure you do not need any data currently on the card or in built-in memory before you format it.
• Formatting built-in memory will delete the following data. – Protected images – Startup screen
• Formatting a memory card will delete the following data. – Protected images
• Make sure the camera’s battery is sufficiently charged before starting a formatting operation. Formatting may not be performed correctly and the camera may stop operating normally if the camera powers down while formatting is in progress.
• Never open the battery cover while formatting is in progress. Doing so can cause the camera to stop operating normally.

Resetting the Camera to Factory Defaults (Reset)

Procedure
[MENU] * “Set Up” Tab * Reset
See page 112 for details about the camera’s factory default settings. The settings below are not reset. WLAN password, World Time settings, clock settings, date style, screen language
95
Other Settings (Set Up)

Appendix

Safety Precautions

DANGER
*
This symbol indicates information that, if ignored or applied incorrectly, creates the danger of death or serious personal injury.
WARNING
*
This indication stipulates matters that have the risk of causing death or serious injury if the product is operated incorrectly while ignoring this indication.
CAUTION
*
This indication stipulates matters that have the risk of causing injury as well as matters for which there is the likelihood of occurrence of physical damage only if the product is operated incorrectly while ignoring this indication.
Symbol Examples
This circle with a line through it (-) means that the indicated action must not be performed. Indications within or nearby this symbol are specifically
!
prohibited. (The example at left indicates that disassembly is prohibited.)
The black dot (0) means that the indicated action must be performed. Indications within this symbol are actions that are specifically instructed to be
$
performed. (The example at left indicates that the power plug must be unplugged from the electrical socket.)
DANGER
*
. Rechargeable Battery
• To charge the battery, use only the method specifically described in this manual. Attempting to charge the battery by an unauthorized means creates the risk of battery overheating, fire, and explosion.
• Do not expose or immerse the battery in fresh water or salt water. Doing so can damage the battery, and cause deterioration of its performance and loss of service life.
• The battery is intended for use with a CASIO Digital Camera only. Use with any other device creates the risk of the battery damage, or deterioration of battery performance and service life.
+
%
+
96
Appendix
DANGER
*
• Failure to observe any of the following precautions creates the risk of battery overheating, fire, and explosion. – Never use or leave the battery near open flame. – Do not expose the battery to heat or fire. – Make sure the battery is oriented correctly when charging it. – Never carry or store the battery together with items that can conduct electricity
(necklaces, pencil lead, etc.).
– Never disassemble the battery, pierce it with a needle, or expose it to strong
impact (hit it with a hammer, step on it, etc.), and never apply solder to it. Never place the battery into a microwave oven, dehumidifier, high-pressure generating device, etc.
– Never remove the outer sticker from the battery.
• Should you ever notice leakage, strange odor, heat generation, discoloration, deformation, or any other abnormal condition while using, charging, or storing a battery, immediately remove it from the camera and keep it away from open flame. Also, do not use the affected battery after the abnormal symptoms disappear.
• Do not use or leave the battery under direct sunlight, in an automobile parked in the sun, or in any other area subject to high temperatures. Doing so can damage the battery, and cause deterioration of its performance and loss of service life. Also, these conditions can cause the battery to swell to the point that you may not be able to remove it.
• Battery fluid can damage your eyes. Should battery fluid get into your eyes accidentally, immediately rinse them with clean tap water and then consult a physician.
-
+
-
+
97
Appendix
WARNING
*
. Smoke, abnormal odor, overheating, and other abnormalities
• Continued use of the camera while it is emitting smoke or strange odor, or while it is overheating creates the risk of fire and electric shock. Immediately perform the following steps whenever any of the above symptoms are present.
1. Turn off the camera.
2. If you are using the USB-AC adapter to power the camera, unplug the power
plug from the power outlet. Also, remove the battery from the camera, taking care to protect yourself against burn injury.
3. Contact your retailer or nearest CASIO authorized service center.
. Keep Away From Fire
• Never expose the camera to fire, which can cause it to explode and creates the risk of fire and personal injury.
. Avoid Use While In Motion
• Never use the camera to record or play back images while operating an automobile or other vehicle, or while walking. Looking at the monitor while in motion creates the risk of serious accident.
. LED Light
• Never use the LED light while it is pointed in the direction of a person operating a motor vehicle. Doing so can interfere with the driver’s vision and create the risk of accident.
. USB-AC Adapter
• Misuse of USB-AC adapter creates the risk of fire and electric shock. Be sure to observe the following precautions. – Use only the specified USB-AC adapter. – Never use the USB-AC adapter with another device. – Use a power outlet that matches the power supply specified for the
USB-AC adapter.
– Never plug the USB-AC adapter or power cord into a wall outlet that is shared
by other devices, or into a shared extension cord.
– Never locate the USB-AC adapter near a stove or other heating device.
• Misuse of the USB-AC adapter can cause them to become damaged, creating the risk of fire and electric shock. Be sure to observe the following precautions. – Never place heavy objects on the USB-AC adapter or subject it to
direct heat.
– Do not modify the USB-AC adapter, allow it to become damaged, or
forcibly bend it. – Do not twist or pull on the power cord. – When in use, locate the cord where it will not be tripped over.
$
-
-
-
-
-
98
Appendix
WARNING
*
• Never touch the power plug while your hands are wet. Doing so creates the risk of electric shock.
• Should the power cord or power plug become damage, contact your retailer or nearest CASIO authorized service center.
• Do not use the USB-AC adapter in areas where liquids them. Liquids create the risk of fire and electric shock.
* Liquids: Water, sports drinks, seawater, animal or pet urine, etc.
• Do not place a flower vase or any other liquid container on top of the USB-AC adapter. Water creates the risk of fire and electric shock.
• Do not touch the camera or USB-AC adapter during lightning storms.
If a power cord was included with your camera
• The power cord that comes with the camera is designed for use in the country where the camera was purchased. If you use the camera in another country, be sure to use a power cord that conforms to that country’s ratings and power supply voltage. Use of an improper power cord creates the risk of fire and electric shock.
• Before going out, be sure to unplug the USB-AC adapter from the power outlet and put in a place away from objects used by animals and pets. An animal or pet chewing on the power cord can cause it short, leading to the risk of fire.
. Water and Foreign Matter
• Water, other liquids, or foreign matter (especially metal) getting inside the camera creates the risk of fire and electric shock. Immediately perform the following steps whenever any of the above symptoms are present. Particular care is required when using the camera where it is raining or snowing, near the ocean or other body of water, or in a bathroom.
1. Turn off the camera.
2. If you are using the USB-AC adapter to power the camera, unplug the power
plug from the power outlet. Also, remove the battery from the camera, taking care to protect yourself against burn injury.
3. Contact your retailer or nearest CASIO authorized service center.
. Disassembly and Modification
• Never try to take it apart or modify it in any way. Doing so creates the risk of electric shock, burn injury, and other personal injury. Be sure to leave all internal inspection, maintenance, and repair up to your retailer or nearest CASIO authorized service center.
* might spill on
" +
-
% 1
+
+
%
!
99
Appendix
WARNING
*
. Dropping and Rough Treatment
• Continued use of the camera after it is damaged by dropping or other rough treatment creates the risk of fire and electric shock. Immediately perform the following steps whenever any of the above symptoms are present.
1. Turn off the camera.
2. If you are using the USB-AC adapter to power the camera, unplug the power
plug from the power outlet. Also, remove the battery from the camera, taking care to protect yourself against burn injury.
3. Contact your retailer or nearest CASIO authorized service center.
. Memory Cards
• Memory cards are small and present a risk of accidentally being swallowed by infants and young children. Keep memory cards out of the reach of infants and young children. If a memory card is ever swallowed accidentally, contact a physician immediately.
. Precaution when Camera is On
• Do not touch the camera for long periods while it is on. The camera becomes warm when on, and long term contact creates the risk of low­temperature burns.
. Interference with other digital devices
• Should you notice radio interference or other problems on other devices is being caused while using this camera, stop using the wireless functions (Remote Capture, image transfer, wireless image viewing, etc.) of this camera, or turn off the camera. Use of wireless functions creates the risk of radio interference and abnormal operation of other devices.
• When in a medical facility or aircraft, comply with instructions of personnel in charge. Electromagnetic waves and other signals emitted by the camera’s wireless function create the risk of accident.
• Do not use the camera’s wireless function while in the vicinity of high precision digital devices or digital devices that use weak signals. Doing so can interfere with proper operation of such digital devices and create the risk of accident.
• When using the camera’s wireless function, keep it away from any person wearing a pacemaker. Magnetism emitted by the camera may affect cardiac pacemakers and other medical devices. Should you ever notice any abnormality, immediately move away from the product and contact a physician.
-
+
+
-
+
-
+
100
Appendix
Loading...