• Before using it, be sure to read the precautions contained in this User’s Guide.
• Keep the User’s Guide in a safe place for future reference.
• For the most up-to-date information about this product, visit the official EXILIM
Website at http://www.exilim.com/
1
Accessories
As you unpack your camera, check to make sure that all accessories shown below
are included. If anything is missing, contact your original retailer.
Rechargeable lithium ion battery
(NP-130)
* The shape of the power cord plug
varies according to country or
geographic area.
Power cordStrap
USB cableAV cable
Charger unit (BC-130L)
To attach the strap to the camera
1
Attach strap
here.
2
2
Read this first!
• The contents of this manual are subject to change without notice.
• The contents of this manual have been checked at each step of the production
process. Feel free to contact us if you notice anything that is questionable,
erroneous, etc.
• Any copying of the contents of this User’s Guide, either in part or its entirety, is
forbidden. Except for your own personal use, any other use of the contents of this
manual without the permission of CASIO COMPUTER CO., LTD. is forbidden
under copyright laws.
• CASIO COMPUTER CO., LTD. shall not be held liable for any damages or lost
profits suffered by you or any third party due to the use or malfunction of this
product.
• CASIO COMPUTER CO., LTD. shall not be held liable for any damages, lost
profits, or claims by third parties arising out of the use of Photo Transport or
YouTube Uploader for CASIO.
• CASIO COMPUTER CO., LTD. shall not be held liable for any damages or lost
profits caused by loss of memory contents due to malfunction, repair, or any other
reason.
• Note that the example screens and product illustrations shown in this User’s Guide
may differ somewhat from the screens and configuration of the actual camera.
LCD Panel
The liquid crystal panel of the monitor screen uses high-precision technology that
provides a pixel yield in excess of 99.99%. This means that some very small number
of pixels may not light or may remain lit at all times. This is due to the characteristics
of the liquid crystal panel, and does not indicate malfunction.
Take a few test shots
Before shooting your final image, shoot a test shot to ensure that the camera is
recording correctly.
The numbers in parentheses indicate the pages where each item is explained.
. Camera
Front
21
Back
76345
9bk
bnbmbl
bo
bp
[ ]
8
Mode dial
1
(pages 24, 32, 61)
Zoom controller
2
(pages 25, 49, 93, 94)
Shutter button (page 24)
3
Flash (page 38)
4
[ON/OFF] (Power)
5
(page 22)
Front lamp
6
(pages 46, 78)
[ECO] button (page 17)
7
Lens
8
Microphone
9
(pages 57, 109)
Back lamp
bk
(pages 25, 38)
[r] (REC) button
bl
(pages 22, 24)
[0] (Movie) button
bm
(page 56)
Strap hole (page 2)
bn
Connector cover
bo
[USB/AV] port
bp
(pages 95, 118, 126,
133)
[ ]
[ ]
bqbrbsbtck
[MENU] button
bq
(page 71)
[p] (PLAY) button
br
(pages 22, 28)
[SET] button (page 34)
bs
Control button
bt
([8][2][4][6])
(pages 12, 29, 34, 38,
71)
Monitor screen
ck
(pages 10, 12)
[
SET
[ ]
]
Bottom
. Charger Unit
1
2
3
Battery/memory card slots (pages 15, 16, 19, 20)
cl
Tripod hole
cm
Use this hole when attaching to a tripod.
Speaker
cn
clcmcn
+7- Contacts
1
[CHARGE] Lamp
2
AC jack
3
9
Monitor Screen Contents
The monitor screen uses various indicators, icons, and values to keep you informed
of the camera’s status.
• The sample screens in this section are intended to show you the locations of all the
indicators and figures that can appear on the monitor screen in various modes.
They do not represent screens that actually appear on the camera.
• The aperture, shutter speed, and ISO sensitivity values will turn orange when you
half-press the shutter button if Auto Exposure is not correct.
10
. Movie Recording
123
8
76
. Snapshot Viewing
2
bq
bp
boblbkbmbn
. Movie Playback
1
23
7
Flash (page 38)
1
Recording mode (page 56)
2
4
5
31
4
5
6
7
8
9
White balance setting (page 85)
3
Remaining movie memory capacity (page 56)
4
Movie recording time (page 56)
5
Exposure compensation (page 48)
6
Battery level indicator (page 16)
7
Histogram (page 164)
8
File type
1
Protect indicator (page 106)
2
Folder name/file name (page 138)
3
Snapshot image quality (page 82)
4
Snapshot image size (page 35)
5
ISO sensitivity (page 45)
6
Aperture value
7
Shutter speed
8
Date/time (page 49)
9
Metering mode (page 86)
bk
White balance setting (page 103)
bl
Flash (page 38)
bm
Recording mode
bn
Battery level indicator (page 16)
bo
Histogram (page 164)
bp
Exposure compensation (page 48)
bq
File type
1
Protect indicator (page 106)
2
Folder name/file name (page 138)
3
4
Movie recording time (page 89)
4
5
Movie image quality (page 82)
5
Date/time (page 49)
6
Battery level indicator (page 16)
7
6
11
Turning Display Information On and Off (Info)
Each press of [8] (DISP) will cycle through display settings that display or hide onscreen information and the Control Panel. You can configure separate settings for the
REC mode and PLAY mode.
Information on,
Control Panel on
Information on,
Control Panel on,
histogram on
Information off,
Control Panel off
• The Control Panel is not displayed and display information settings cannot be
changed during movie recording.
Displays setting information and the Control Panel.
• While A, S, or M is selected as the recording mode, the
aperture and shutter speed specified for snapshots are
displayed.
Displays setting information and the
Control Panel, and a histogram (page
164) on the left side of the display. Also
displays the remaining movie recording
Histogram
time as well as a movie image quality
icon.
• While A, S, or M is selected as the recording mode, the
aperture and shutter speed specified for movies are
displayed.
Hides setting information and the Control Panel.
12
Quick Start Basics
What you can do with your CASIO camera
Your CASIO camera is packed with a powerful selection of features and functions to
make recording of digital images easier, including the following three main functions.
Premium Auto
Select Premium Auto recording and the camera automatically determines
whether you are shooting a subject or scenery, and other conditions. Premium
Auto delivers higher image quality than standard Auto.
See page
24 for more information.
HDR Art
An HDR Art feature combines different parts of a
burst of images shot with different exposures into a
final image and performs high-precision image
analysis to produce final images that are true works
of art.
See page 66 for more information.
Advanced Dynamic Photo
Extract people or objects out of images you shoot and insert them into another
snapshot or movie (background). You can even insert a moving subject to
create true Dynamic Photo images.
See page
111 for more information.
13
Quick Start Basics
First, charge the battery prior to use.
Note that the battery of a newly purchased camera is not charged. Perform the steps
under “To charge the battery” to bring the battery to a full charge.
• Your camera requires a special CASIO rechargeable lithium ion battery (NP-130)
for power. Never try to use any other type of battery.
To charge the battery
1. Aligning the positive
negative
-
terminals of the battery
+
and
with those of the charger unit, load
the battery into the charger unit.
2. Plug the charger unit into a
household power outlet.
About 240 minutes are required to
reach full charge. The [CHARGE]
lamp will go out when charging is
complete. Unplug the power cord
from the power outlet and then
remove the battery from the charger.
Lamp StatusDescription
Lit RedCharging
Flashing Red
OffCharging complete
Abnormal ambient temperature, charger problem, or
battery problem (page 158)
[CHARGE] lamp
14
Quick Start Basics
Other Charging Precautions
• Use the special charger (BC-130L) to charge the special lithium ion battery (NP-
130). Never use any other type of charger device. Attempting to use a different
charger can result in unexpected accident.
• A battery that is still warm due to normal use may not charge fully. Give the battery
time to cool before charging it.
• A battery discharges slightly even when it is not loaded in the camera. Because of
this, it is recommended that you charge the battery immediately before you need to
use it.
• Charging the camera’s battery may cause interference with TV and radio reception.
If this happens, plug the charger into an outlet that is further away from the TV or
radio.
• Actual charging time depends on current battery capacity and charging conditions.
To load the battery
1. Open the battery cover.
Slide the battery cover slider towards OPEN
and then open it as indicated by the arrows
in the illustration.
2. Load the battery.
With the EXILIM logo on the
battery facing downwards (in
the direction of the lens), hold
the stopper next to the battery
in the direction indicated by
the arrow as you slide the
battery into the camera. Press
the battery in until the stopper
secures it in place.
3. Close the battery cover.
Close the battery cover and then shift the
slider towards LOCK.
Battery
contacts
15
Stopper
OKNG
EXILIM logo
Quick Start Basics
To replace the battery
1. Open the battery cover and
remove the current battery.
With the monitor screen side of the
camera facing upwards, slide the
stopper in the direction indicated by
the arrow in the illustration. After the
battery pops out, pull it the rest of the
way out of the camera.
Stopper
2. Load a new battery.
Checking Remaining Battery Power
As battery power is consumed, a battery indicator on the monitor screen indicates
remaining power as shown below.
Remaining PowerHighLow
Battery Indicator***
Indicator ColorCyan* Amber*Red*Red
indicates battery power is low. Charge the battery as soon as possible.
Recording is not possible when is indicated. Charge the battery immediately.
• The level shown by the battery indicator may change when you switch between the
REC mode and PLAY mode.
• Leaving the camera for about 30 days with no power supplied while the battery is
dead will cause its date and time settings to be cleared. A message telling you to
configure time and date settings will appear the next time you turn on the camera
after restoring power. When this happens, configure date and time settings (page
145).
• See page 178 for information about battery life and number of shots.
Battery Power Conservation Tips
• Entering the “ECO Mode” enables low-power operation (page 17).
• When you do not need to use the flash, select ? (Flash Off) for the flash setting
(page 38).
• Enable the Auto Power Off and the Sleep features to protect against wasting
battery power when you forget to turn off the camera (pages 147, 147).
• Select “Off” for “Continuous AF” (page 77).
16
Quick Start Basics
Enabling Power Saving (ECO Mode)
Enabling power saving reduces the brightness of the monitor screen and switches
other camera operations to low-power operation, which allows a charge to last longer
and increase the number of images that can be shot between charges.
The “ECO Mode” can be enabled only while Auto is selected as the recording mode
(page 32).
1. Press [ECO].
This enters the “ECO Mode”, which is indicated by e on the monitor screen.
• Each press of [ECO] toggles the “ECO Mode” between on and off.
NOTE
• Changing the mode dial setting while the “ECO Mode” is “On” will turn the “ECO
Mode” “Off” automatically and change the recording mode to the current mode dial
selection.
• You can achieve even greater power savings by using the “ECO Mode” in
combination with Auto Power Off (page 147) and Sleep (page 147).
17
Quick Start Basics
Configuring Basic Settings the First Time You Turn On the
Camera
The first time you load a battery into the camera, a screen appears for configuring the
display language, date, and time settings. Failure to set the date and time correctly
will cause the wrong date and time data to be recorded with images.
IMPORTANT!
• A screen for language selection will not appear in step 2 of the procedure below if
you purchased a camera intended for the Japanese market. To change the display
language from Japanese in this case, use the procedure under “Specifying the
Display Language (Language)” (page 146). Note that a version of this manual in
the language you select may not be included with a camera intended for the
Japanese market.
• Camera models sold in certain geographic areas may not support display language
selection.
1. Press [ON/OFF] (Power) to turn on the
camera.
2. Use [8], [2], [4], and [6] to select the
language you want and then press
[SET].
[ON/OFF] (Power)
[ ]
[ ]
[ ]
[0] (Movie)
3. Use [8] and [2] to select a date style and then press [SET].
Use [4] and [6] to select the setting you want to
change and then use [8] and [2] to change it.
To switch between 12-hour and 24-hour format, press
[0] (Movie).
5. After setting the date and time, use [4] and [6]
to select “Apply” and then press [SET].
If you make a mistake configuring display language, date, or time settings with the
above procedure, refer to the following pages for information about how to correct
the settings.
– Display language: Page 146
– Date and time: Page 145
[
SET
[ ]
]
18
Quick Start Basics
NOTE
• Each country controls its local time offset and the use of summer time, and so they
are subject to change.
• Removing the battery from the camera too soon after configuring time and date
settings for the first time can cause the settings to be reset to their factory defaults.
Do not remove the battery for at least 24 hours after configuring settings.
Preparing a Memory Card
Though the camera has built-in memory that can be used to store images and
movies, you probably will want to purchase a commercially available memory card for
greater capacity. The camera does not come with a memory card. Images and
movies recorded while a memory card is loaded are saved to the memory card. When
no memory card is loaded, images and movies are saved to built-in memory.
• For information about memory card capacities, see page 174.
Supported Memory Cards
– SD Memory Card (Up to 2GB)
– SDHC Memory Card (2GB to 32GB)
– SDXC Memory Card (32GB to 2TB)
Use one of the above types of memory card.
• The above are supported memory card types as of February 2012.
• Noted memory card capacities are standard values.
• Use only SD cards that are compliant with the SD Card Association specification.
• This camera supports use of Eye-Fi cards.
To load a memory card
1. Press [ON/OFF] (Power) to turn off the
camera and then open the battery
cover.
Slide the battery cover slider towards OPEN
and then open it as indicated by the arrows
in the illustration.
19
Quick Start Basics
2. Load a memory card.
Positioning the memory card so its front
is facing upwards (towards the monitor
screen side of the camera), slide it into
the card slot all the way in until you
hear it click securely into place.
FrontBack
Front
3. Close the battery cover.
Close the battery cover and then shift the
slider towards LOCK.
IMPORTANT!
• Never insert anything besides a supported memory card (page 19) into the memory
card slot.
• Should water or any foreign object ever get into the card slot, immediately turn off
the camera, remove the battery, and contact your retailer or nearest CASIO
authorized service center.
To replace the memory card
Press the memory card and then release it. This will
cause it to pop out of the memory card slot slightly.
Pull the card out the rest of the way and then insert
another one.
• Never remove a card from the camera while the
back lamp is flashing green. Doing so can cause the
image save operation to fail and even damage the
memory card.
20
Quick Start Basics
To format (initialize) a new memory card
Before using a memory card for the first time with the camera, you must format it.
IMPORTANT!
• Formatting a memory card that already has snapshots or other files on it, will delete
its contents. Normally you do not need to format a memory card again. However, if
storing to a card has slowed down or if you notice any other abnormality, re-format
the card.
• Be sure to use the camera to format a memory card. Formatting a memory card on
a computer and then using it in the camera can slow down data processing by the
camera. In the case of an SD, SDHC, or SDXC memory card, formatting on a
computer can result in non-conformity with the SD format, causing problems with
compatibility, operation, etc.
• Before formatting a new Eye-Fi card to use it for the first time, copy the Eye-Fi
Manager install files to your computer. Do this before formatting the card.
1. Turn on the camera and press [MENU].
2. Select the “Set Up” tab, select “Format” and then press [6].
3. Use [8] and [2] to select “Format” and then press [SET].
21
Quick Start Basics
Turning the Camera On and Off
To turn power on
Pressing [ON/OFF] (Power) enters the REC mode so
you can record images. Pressing [p] (PLAY) while in
the REC mode enters the PLAY mode, which you can
use to view snapshots and movies (pages 28, 89).
•Pressing [r] (REC) while in the PLAY mode
returns to the REC mode.
• Take care to ensure that nothing is restricting or
coming into contact with the lens as it extends.
Holding the lens with your hand so it cannot extend
creates the risk of malfunction.
• About 10 seconds after you press [p] (PLAY) to
enter the PLAY mode, the lens will retract into the
camera.
• The Sleep function or Auto Power Off (pages 147,
147) will turn off power automatically if you do not
perform any operation for a preset amount of time.
[ON/OFF] (Power)
Back lamp
[r] (REC) [p] (PLAY)
To turn off the camera
Press [ON/OFF] (Power).
NOTE
• You also can configure the camera to turn on or off when you press [r] (REC) or
[p] (PLAY) (page 148).
22
Quick Start Basics
Holding the Camera Correctly
Your images will not come out clearly if you move the camera when you press the
shutter button. When pressing the shutter button, be sure to hold the camera as
shown in the illustration below, and keep it still by pressing your arms firmly against
your sides as you shoot.
Holding the camera still, carefully press the shutter button and take care to avoid all
movement as the shutter releases and for a few moments after it releases. This is
especially important when available lighting is low, which slows down the shutter
speed.
HorizontalVertical
Hold the camera so the flash is
above the lens.
NOTE
• Take care that your fingers and the strap do not
cover any of the areas indicated in the illustration.
• To protect against accidentally dropping the
camera, attach the wrist strap and make sure it is
around your fingers or wrist while you are operating
the camera.
• Never swing the camera around by its strap.
• The supplied strap is intended for use with this
camera only. Never use it for any other purpose.
IMPORTANT!
• Take care to ensure that your fingers are not blocking or
are not too close to the flash. Fingers can cause unwanted
shadows when using the flash.
Flash
Front lamp
Lens
23
Quick Start Basics
To shoot a snapshot
R
Selecting an Auto Recording Mode
You can select one of two auto recording modes (Auto or Premium Auto) according to
your digital imaging needs.
AutoThis is the standard Auto recording mode.
With Premium Auto recording, the camera automatically
determines whether you are shooting a subject or scenery,
and other conditions. Premium Auto recording delivers higher
Ÿ
Premium Auto
image quality than standard Auto recording.
• Premium Auto recording takes longer to process image data
after it is shot than Auto recording.
• It also requires more power (and runs down the battery
quicker) than Auto.
1. Press [ON/OFF] (Power) to turn on the camera.
The camera will enter the REC mode.
• If the camera is in the PLAY mode, press [r] (REC).
• You also can configure the camera to turn on when you press [r] (REC) or
[p] (PLAY) (page 148).
2. Set the mode dial to t (Auto) or Ÿ (Premium Auto) to select Auto
recording mode (page 32).
Auto recording mode icon
[ON/OFF] (Power)
Shutter button
Mode dial
Remaining Snapshot Memory
Capacity (page 174)
Monitor screen
24
[r] (REC)
[p] (PLAY)
Quick Start Basics
To shoot a snapshot
1. Point the camera at the subject.
If you are using Premium Auto, text will appear in the
lower right corner of the monitor screen describing the
type of shot the camera has detected.
• You can zoom the image, if you want.
w Wide Anglez Telephoto
Zoom controller
Appears when the
camera detects it is
stationary on a tripod.
2. Half-press the shutter button to
focus the image.
When focus is complete, the camera
will beep, the back lamp will light green,
and the focus frame will turn green.
Half-press
Press lightly
until the button
stops.
Beep, beep (Image is in focus.)
Back lamp
Focus frame
When you half-press the shutter button, the
camera automatically adjusts exposure and
focuses on the subject it is currently pointed
at. Mastering how much pressure is required
for a half-press and a full-press of the shutter
button is an important technique for goodlooking images.
25
Quick Start Basics
3. Continuing to keep the camera still, press the shutter button the rest of
the way down.
This records the snapshot.
Full-press
Snap (Image is recorded.)
Recording a Movie
Press [0] (Movie) to start
movie recording. Press
[0] (Movie) again to stop
movie recording. See
page 56 for details.
[0] (Movie)
. If the image does not focus...
If the focus frame stays red and the back lamp is flashing green, it means that the
image is not in focus (because the subject is too close, etc.). Re-point the camera at
the subject and try to focus again.
. Shooting with Auto
If the subject is not in the center of the frame...
“Focus lock” (page 42) is the name of a technique you can use when you want to
shoot an image in which the subject to be focused on is not within the focus frame in
the center of the screen.
To track the movement of a moving subject
Half-press the shutter button to follow and focus automatically on a moving subject.
See “Ë Tracking” (page 43) for more information.
26
Quick Start Basics
. Shooting with Premium Auto
• In addition to shutter speed, aperture, and ISO sensitivity, the camera
automatically executes the following operation as required when shooting with
Premium Auto.
– Auto Focus is normally performed until you half-press the shutter button.
– Intelligent AF (Page 43)
– Face Detection (Page 47)
– Make-up/Landscape (Pages 83, 84)
• Shooting with Premium Auto can cause vibration and noise to occur due to lens
operation. This does not indicate malfunction.
• When Shooting with Premium Auto, the message “Processing Premium Auto.
Please wait...” may appear on the monitor screen. If you feel the camera is taking
too long to process data, try shooting with standard Auto instead.
• In some cases, Premium Auto may not be able to interpret the shooting
environment correctly. If this happens, shoot with standard Auto.
27
Quick Start Basics
Viewing Snapshots
Use the following procedure to view snapshots on the camera’s monitor screen.
• For information about how to play back movies, see page 89.
1. Turn on the camera and press [p]
(PLAY) to enter the PLAY mode.
• This will display one of the snapshots
currently stored in memory.
• Information about the displayed
snapshot also is included (page 11).
• You also can clear the information to
view only the snapshot (page 12).
• You can zoom in on the image by
sliding the zoom controller towards z (page 93). If you are recording a
snapshot that is very important to you, it is recommended that you zoom the
image and check its details after recording it.
[p] (PLAY)
2. Use [4] and [6] to scroll between images.
• Holding down either button scrolls at high speed.
[6]
[6]
[4]
NOTE
• Half-pressing the shutter button while in the PLAY mode or while a menu screen is
displayed will switch directly to the REC mode.
28
[4]
Quick Start Basics
Deleting Snapshots and Movies
If memory becomes full, you can delete snapshots and movies you no longer need to
free up storage and record more images.
IMPORTANT!
• Remember that a file (image) delete operation cannot be undone.
• Deleting an audio snapshot (page 109) deletes both the snapshot and the audio
file.
• The delete menu will not appear if you press [2] () while “On” is selected for
the camera’s “Ü Disabled” setting (page 148). You can delete files only while “Off”
is selected for “Ü Disabled”.
To delete a single file
1. Press [p] (PLAY) to enter the PLAY mode and then
press [2] ().
2. Use [4] and [6] to scroll through the files until the one
you want to delete is displayed.
3. Use [8] and [2] to select “Delete” and then press [SET].
• To delete other files, repeat steps 2 and 3.
• To exit the delete operation, press [MENU].
To delete specific files
1. Press [p] (PLAY) to enter the PLAY mode and then press [2] ().
2. Use [8] and [2] to select “Delete Files” and then press [SET].
• This displays a file selection screen.
3. Use [8], [2], [4], and [6] to move the selection boundary to the file
you want to delete, and then press [SET].
• This will select the check box of the currently selected file.
4. Repeat step 3 to select other files, if you want. After you are finished
selecting files, press [MENU].
5. Use [8] and [2] to select “Yes” and then press [SET].
• This deletes the files you selected.
• To cancel the delete operation, select “No” in step 5 and then press [SET].
29
Quick Start Basics
To delete all files
1. Press [p] (PLAY) to enter the PLAY mode and then press [2] ().
2. Use [8] and [2] to select “Delete All Files” and then press [SET].
3. Use [8] and [2] to select “Yes” and then press [SET] to delete all files.
This will cause the message “There are no files” to appear.
Snapshot Shooting Precautions
Operation
• Never open the battery cover while the back lamp is flashing green. Doing so can
result in the image you just shot being saved incorrectly, damage to other images
stored in memory, malfunction of the camera, etc.
• If unwanted light is shining directly onto the lens, shade the lens with your hand
when shooting an image.
Monitor Screen when Shooting Snapshots
• Subject brightness conditions can cause monitor screen response to slow and can
cause digital noise in the monitor screen image.
• The image that appears on the monitor screen is for image composition. The actual
image will be recorded at the quality set for the image quality setting (page 82).
Shooting Indoors under Fluorescent Lighting
• Minute flickering of fluorescent lighting can affect the brightness or color of an
image.
30
Quick Start Basics
Loading...
+ 150 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.