• Before using it, be sure to read the precautions contained in this User’s Guide.
• Keep the User’s Guide in a safe place for future reference.
• For the most up-to-date information about this product, visit the official EXILIM
Website at http://www.exilim.com/
Accessories
As you unpack your camera, check to make sure that all accessories shown below
are included. If anything is missing, contact your original retailer.
Rechargeable lithium ion
battery (NP-130A)
Power cord
2
*
USB-AC adaptor*
(AD-C54UG/AD-C53U)
Micro USB cableBasic Reference
1
Neck strapLens cap
*1 The type of USB-AC adaptor included varies according to the country or
geographic area where the camera is sold.
*2 A power cord is included with the AD-C53U USB-AC adapter. The shape of the
power cord plug varies according to the country or geographic area where the
camera is sold.
2
Attaching and Removing the Lens Cap
The lens cap opens and closes
automatically in accordance with the
lens position, so you can leave it in
place, if you want. Make sure the lens
cap is attached to the lens so the dot
mark on the cap is upwards, with the
large blades of the cap on the left and
right. If the cap is in the wrong position,
its blades can cause partial darkening
of images when shooting with flash.
Attach the lens cap with the large blades
on the left and right.
Attaching the Neck Strap to the Camera
• Attach either end of the strap to the two strap
rings on the sides of the camera as shown in the
illustration.
• After you are finished pull on the strap to test it
and to make sure it does not come loose.
. Adjusting the Length of the Strap
You can adjust the length of the strap so it can
be used as a neck strap or a shoulder strap.
Mark
Removal
Attachment
1. Pull the strap out at the center
of the buckle in the direction
indicated by
1
.
2. Pull the strap in one of the
directions indicated by the
illustration to adjust the length.
To lengthen
To shorten
1
3
Read this first!
• The contents of this manual are subject to change without notice.
• The contents of this manual have been checked at each step of the production
process. Feel free to contact us if you notice anything that is questionable,
erroneous, etc.
• Any copying of the contents of this User’s Guide, either in part or its entirety, is
forbidden. Except for your own personal use, any other use of the contents of this
manual without the permission of CASIO COMPUTER CO., LTD. is forbidden
under copyright laws.
• CASIO COMPUTER CO., LTD. shall not be held liable for any damages or lost
profits suffered by you or any third party due to the use or malfunction of this
product.
• CASIO COMPUTER CO., LTD. shall not be held liable for any damages or lost
profits caused by loss of memory contents due to malfunction, repair, or any other
reason.
• Note that the example screens and product illustrations shown in this User’s Guide
may differ somewhat from the screens and configuration of the actual camera.
LCD Panel
The liquid crystal panel of the monitor screen uses high-precision technology that
provides a pixel yield in excess of 99.99%. This means that some very small number
of pixels may not light or may remain lit at all times. This is due to the characteristics
of the liquid crystal panel, and does not indicate malfunction.
Take test shots
Before shooting your final image, shoot a test shot to ensure that the camera is
recording correctly.
The monitor screen uses various indicators, icons, and values to keep you informed
of the camera’s status.
• The sample screens in this section are intended to show you the locations of all the
indicators and figures that can appear on the monitor screen in various modes.
They do not represent screens that actually appear on the camera.
. Snapshot Recording (1 Shot)
Snapshot image size/Quality (pages 116, 118)
13567824
cq
cp
co
cn
cm
cl
ck
bt
Self-timer mode (page 47)
1
Face Detection (page 123)
2
Recording mode (page 35)
3
Image deterioration indicator/
4
Zoom (SR) indicator (page 62)
Remaining movie memory
5
capacity (page 81)
Remaining snapshot memory
6
capacity (page 225)
brbsbq
7
Movie quality (FHD/STD movie)
8
9
(pages 81, 84)/
bk
Recording speed (high speed movie) (page 84)
bl
AF Area (page 124)
9
bm
Focal distance
bk
bn
(Converted to 35 mm film format.) (page 61)
bo
Anti Shake (page 121)
bl
bp
Timestamp indicator (page 189)
bm
Histogram (page 111)
bn
Front shutter button function (page 114)
bo
ND Filter (page 115)
bp
Date/Time (pages 28, 194)
bq
Focus frame (pages 36, 124)
br
Electronic level (page 111)
bs
Battery level indicator (page 28)
bt
Metering mode (page 58)
ck
Flash (page 56)
cl
Exposure compensation (page 55)
cm
Make-up level (page 54)
cn
ISO sensitivity (page 53)
co
Focus mode (page 50)
cp
White balance (page 48)
cq
NOTE
• Depending on recording settings, the aperture, shutter speed, and ISO sensitivity
values may not appear on the monitor screen. These values will be red if the Auto
Exposure (AE) is not correct for some reason.
Each press of [8] (DISP) will cycle through display settings that
display or hide on-screen information. You can configure separate
settings for the REC mode and PLAY mode.
REC mode
Information onDisplays setting information.
Information offHides setting information.
PLAY mode
Information on
Displays settings when shooting, current date and time,
histogram (page 111), and other information.
Information offNo information displayed when shooting.
With thumbnails
Shows images that come before and after the current
image.
[8] (DISP)
Monitor Screen Contents and How to Change Them
17
Quick Start Basics
What you can do with your CASIO camera
Your CASIO camera is packed with a powerful selection of features and functions to
make recording of digital images easier, including the following main functions.
Intelligent Bracketing
You can use this function to shoot a series of images,
slightly changing the camera setup with each shot.
*See page 64 for more information.
180 degrees
90 degrees
Tiltable Monitor Screen
The camera’s monitor screen can be tiled upwards
up to 180 degrees. This makes it easy to compose
self-portraits and to shoot from low angles.
*See page 20 for more information.
Handsfree Self-portraits
You can control operation of the self-timer from a
distance by waving your hand, which makes it easier to
shoot self-portraits from a distance.
*See page 73 for more information.
Interval Shot
You can record a series of images over a specified
period. This function is useful when recording the
movement of stars, a blooming flower, etc.
*See page 65 for more information.
Time Lapse Movie
You can use this function to record movies of natural
events that occur over time, to speed up the flow of
traffic in a city scene, or to record other similar types of
movies.
*See page 88 for more information.
18
Quick Start Basics
ART SHOT
A variety of artistic effects help to make even common,
ordinary subjects become more novel and exciting.
“ART SHOT” provides the following effects: HDR Art,
Toy Camera, Soft Focus, Light Tone, Pop, Sepia,
Monochrome, Miniature, Fisheye, Sparkling Shot,
Crystal ball.
*See page 76 for more information.
Triple Shot
Pressing the shutter button shoots a burst of three
images and stores them in memory. This feature is
great for making sure you don’t miss those special
moments when kids are around.
*See page 94 for more information.
Premium Auto Pro
Select Premium Auto Pro recording and the
camera automatically determines whether you
are shooting a subject or scenery, and other
conditions. Premium Auto Pro delivers higher
image quality than standard Auto.
*See page 35 for more information.
Wireless LAN Connection
Turns your smartphone into a camera remote
controller and allows you to send images recorded with
your camera to your smartphone.
*See page 159 for more information.
19
Quick Start Basics
Tilting the Monitor Screen
The monitor screen can be tilted upwards up to 180 degrees or downwards up to
55 degrees.
. Tilting the Monitor Screen
As shown in the illustration, you can tilt the monitor screen by opening it from the
bottom or from the top.
180 degrees
55 degrees
90 degrees
IMPORTANT!
• Under factory default settings, the camera will turn on automatically whenever the
monitor screen is tilted. See page 192 for information about configuring the camera
so it does not turn on when the monitor screen is tilted upwards.
• When returning the monitor screen to the back of the camera, take care so you do
not catch your fingers between the top or bottom of the monitor screen and the
camera.
• Do not subject the monitor screen to strong impact. Doing so can damage it.
NOTE
• Be sure to return the monitor screen to its normal position to the back of the
camera when you are not using it.
• Whenever placing the camera on a tabletop or other surface to shoot, be sure to
pull out the stand to keep it from falling over (page 22).
20
Quick Start Basics
. Returning the Monitor Screen to Its Normal Position
1. Hold the bottom of the
monitor screen and
rotate it, or press the top
of the monitor screen to
return it to its normal
position.
2. Slide the monitor screen up as far as it will go.
. What you can do with the camera...
Shoot self-portraits
You can position the monitor screen so it
faces in the same direction as the lens,
for easy composition of self-portraits. You
can also use a stand on the back of the
camera to keep the camera upright when
placed on a tabletop or other surface.
21
Quick Start Basics
Low-angle shotsHigh-angle shots
The tilt angle of the monitor screen can
be adjusted for each composition of
You can tilt the monitor screen in a way
that allows you to shoot from high angles.
images from various low angles.
Using the Stand
Your camera has a built-in stand. You can pull out
the stand and keep the camera stable on a tabletop
or other surface while the monitor screen is tilted
upwards 180 degrees. When using the camera on a
tabletop or other surface for landscape (horizontal)
orientation shots, you can adjust the vertical angle of
the camera somewhat by changing how far you pull
out the stand.
IMPORTANT!
• When using the camera on a tabletop or other
surface for portrait (vertical) orientation shots, pull
the stand out as much as possible so the camera
is stable. Pulling the stand out part way in this
case can cause the camera to become unstable
and fall over.
• Even when using the stand to adjust the vertical
angle of the camera while shooting with landscape (horizontal) orientation, take
care to extend the stand far enough to avoid camera instability, which can cause it
to fall over.
• Whenever using the stand, make sure that the location where you place the
camera is stable and relatively level.
Stand
22
Quick Start Basics
First, charge the battery prior to use.
Note that the battery of a newly purchased camera is not charged. Perform the steps
below to load the battery into the camera and charge it.
• Your camera requires a special CASIO rechargeable lithium ion battery (NP-130A)
for power. Never try to use any other type of battery.
To load the battery
1. Open the battery cover.
2. Load the battery.
With the CASIO logo on the battery
facing downwards (in the direction
of the lens), hold the stopper next
to the battery in the direction
indicated by the arrow as you slide
the battery into the camera. Press
the battery in until the stopper
secures it in place.
3. Close the battery cover.
Battery
OK
Stopper
NG
CASIO logo
23
Quick Start Basics
To replace the battery
Stopper
1. Open the battery cover and
remove the current battery.
2. Load a new battery.
Charge the Battery
You can use either of the two following methods to charge the camera’s battery.
• USB-AC adaptor
• USB connection to a computer (Using the included micro USB cable.)
. To charge with the USB-AC adaptor
The adaptor lets you charge the battery while it is loaded in the camera.
While the camera is turned off, connect in the sequence shown below.
Charging time: Approximately 240 minutes
USB-AC adaptor
(AD-C54UG)
2
1
Micro USB cable
[USB] port
(included with camera)
24
1
2
Power cord
3
4
u mark of the small (micro USB) connector facing the
monitor screen side of the camera.
• When disconnecting the USB-AC adaptor from the camera, be sure to disconnect
from the camera first.
USB-AC adaptor (AD-C53U)
3
Quick Start Basics
IMPORTANT!
• A battery that has not been used for a long time, or ambient temperature extremes
can cause charging to take longer than normal. If charging takes longer than about
five hours, a timer will terminate it automatically, even if the battery is not fully
charged. This is indicated by the back lamp flashing red. If the battery has not been
used for a very long time, charging may be terminated automatically and the back
lamp may start flashing red after only about 60 minutes. In either case, disconnect
the USB cable from the camera and then reconnect it to resume charging.
• Make sure that you insert the cable connector into the [USB] port until you feel it
click securely into place. Failure to insert the connector fully can result in poor
communication or malfunction.
• Note that even while the connector is fully inserted, you
still will be able to see the metal part of the connector as
shown in the illustration.
• Pressing [ON/OFF] (Power) while the USB-AC adaptor is
connected to the camera will turn on the camera with
power being supplied by the battery. Because of this,
charging will stop.
• The USB-AC adaptor will become warm during charging.
This is normal and does not indicate malfunction.
• The shape of the power plug depends on each country or geographic area.
Back Lamp Operation
Lamp StatusDescription
Lit RedCharging
Abnormal ambient temperature,
Flashing Red
USB-AC adaptor problem, or battery
problem (page 212)
OffCharging complete
Back lamp
25
Quick Start Basics
. To charge using a USB connection to a computer
USB connection lets you charge the battery while it is loaded in the camera.
While the camera is turned off, connect in the sequence shown below (
1, 2
(power turned on)
).
Computer
USB port
[USB] port
Micro USB cable
1
u mark of the small (micro USB) connector facing the
monitor screen side of the camera.
(included with camera)
USB
2
• If the camera is on, press [ON/OFF] (Power) to turn it off before connecting it to
your computer.
IMPORTANT!
• The first time you connect the camera to your computer with the USB cable, an
error message may appear on your computer. If this happens, disconnect and then
reconnect the USB cable.
• A battery that has not been used for a long time, certain types of computers, and
connection conditions can cause charging to take more than approximately five
hours, which will trigger a timer that terminates charging automatically, even if the
battery is not fully charged. If this happens, disconnect and then reconnect the
USB cable to restart charging. To complete charging faster, use of the included
USB-AC adaptor is recommended.
• If the battery has not been used for a very long time, charging may terminate
automatically and the back lamp may start flashing red or go out after only about
60 minutes. In either case, use of the USB-AC adaptor that comes with the camera
is recommended.
• If you turn on the camera while charging over a USB connection to a computer is in
progress, the camera will establish a USB connection with the computer. Though
charging normally should continue at this time, certain types of computers or
connection environments may stop charging if supply power is low. This will be
indicated by the camera’s back lamp lighting green.
• Charging is not performed while the connected computer is in the hibernate mode.
26
Quick Start Basics
Back Lamp Operation
Lamp StatusDescription
Lit Red,
(Lit/Flashing Amber)
Charging
Abnormal ambient temperature,
Flashing Red
charging taking abnormally long, or
battery problem (page 212)
Back lamp
Off, (Lit Green)Charging complete
• The information in parentheses in the above table shows the lamp status while the
camera is turned on during charging.
Other Charging Precautions
• With the two charging methods described above, you can charge the camera’s
battery (NP-130A) without removing it from the camera. You also can charge the
battery using an optionally available charger unit (BC-130L). Never use any other
type of charger device. Attempting to use a different charger can result in
unexpected accident.
• This model can be charged only via from USB 2.0 specification USB port only.
• USB charging devices and power supply devices are subject to fixed standards.
Use of an inferior device or a device that is not up to standard can cause
malfunction and/or failure of your camera.
• Operation is not guaranteed in the case of a computer built or modified by you.
Even in the case of a commercially available computer, certain USB port
specifications may make it impossible to charge via the USB cable.
• A battery that is still warm immediately after normal use may not charge fully. Give
the battery time to cool before charging it.
• A battery discharges slightly even when it is not loaded in the camera. Because of
this, it is recommended that you charge the battery immediately before you need to
use it.
• Charging the camera’s battery may cause interference with TV and radio reception.
If this happens, plug the USB-AC adaptor into an outlet that is further away from
the TV or radio.
• Actual charging time depends on current battery capacity and charging conditions.
• Do not use the USB-AC adaptor with any other device.
• Never use the power cord with another device.
• Use only the USB-AC adaptor and USB cable specified in this manual for charging.
Use of any other type of devices may result in improper charging.
27
Quick Start Basics
Checking Remaining Battery Power
As battery power is consumed, a battery indicator on the monitor screen indicates
remaining power as shown below.
Remaining PowerHighLow
Battery Indicator***
Indicator ColorWhite* White*Red*Red
indicates battery power is low. Charge the battery as soon as possible.
Recording is not possible when is indicated. Charge the battery immediately.
• The level shown by the battery indicator may change when you switch between the
REC mode and PLAY mode.
• Leaving the camera for about 30 days with no power supplied while the battery is
dead will cause its date and time settings to be cleared. A message telling you to
configure time and date settings will appear the next time you turn on the camera
after restoring power. When this happens, configure date and time settings (page
194).
• See page 230 for information about battery life and number of shots.
Battery Power Conservation Tips
• Entering the “ECO Mode” enables low-power operation (page 187).
• When you do not need to use the flash, select ? (Flash Off) for the flash setting
(page 56).
• Enable the Auto Power Off and the Sleep features to protect against wasting
battery power when you forget to turn off the camera (pages 191, 191).
• Select “Off” for “Continuous AF” (page 125).
Configuring Basic Settings the First Time You Turn On the
Camera
The first time you load a battery into the camera, a screen appears for configuring the
display language, date, and time settings. Failure to set the date and time correctly
will cause the wrong date and time data to be recorded with images.
IMPORTANT!
• A screen for language selection will not appear in step 2 of the procedure below if
you purchased a camera intended for the Japanese market. To change the display
language from Japanese in this case, use the procedure under “Specifying the
Display Language (Language)” (page 195). Note that a version of this manual in
the language you select may not be included with a camera intended for the
Japanese market.
• Camera models sold in certain geographic areas may not support display language
selection.
28
Quick Start Basics
1. Press [ON/OFF] (Power) to turn on the
[ON/OFF] (Power)
camera.
2. Use [8], [2], [4], and [6] to select the
language you want and then press
[SET].
3. Use [8] and [2] to select a date style and then press [SET].
Example: July 10, 2015
YY/MM/DD
DD/MM/YY
MM/DD/YY
* 15/7/10
* 10/7/15
* 7/10/15
4. Set the date and the time.
Use [4] and [6] to select the setting you want to
change and then use [8] and [2] to change it.
To switch between 12-hour and 24-hour format, select
“24h” and then use [8] and [2] to change the setting.
5. After setting the date and time, use [4] and [6]
to select “Apply” and then press [SET].
If you make a mistake configuring display language, date, or time settings with the
above procedure, refer to the following pages for information about how to correct
the settings.
– Display language: page 195
– Date and time: page 194
NOTE
• Each country controls its local time offset and the use of summer time, and so they
are subject to change.
• Removing the battery from the camera too soon after configuring time and date
settings for the first time can cause the settings to be reset to their factory defaults.
Do not remove the battery for at least 24 hours after configuring settings.
29
Quick Start Basics
Preparing a Memory Card
Though the camera has built-in memory that can be used to store images and
movies, you probably will want to purchase a commercially available memory card for
greater capacity. The camera does not come with a memory card. Images recorded
while a memory card is loaded are saved to the memory card. When no memory card
is loaded, images are saved to built-in memory.
• For information about memory card capacities, see page 225.
• The above are supported memory card types as of January 2014.
• This camera supports use of SD memory cards of the following types and
capacities: SD memory cards up to 2GB, SDHC memory cards from 2GB up to
32GB, SDXC memory cards from 32GB up to 2TB. Note that the ability to use any
particular card with this camera, even if it satisfies the above capacity and type
requirements, is not guaranteed.
. Memory Card Handling Precautions
Certain types of cards can slow down processing speeds, and even can make it
impossible to store High Quality movies correctly. Also, use of certain types of
memory cards slows down data transfer and increases the time it takes to record
movie data, which can result in movie frames being dropped. The Y indicator on the
monitor screen turns yellow to indicate that frames are being dropped. In order to
avoid problems such as these, use of an Ultra High Speed Type SD memory card is
recommended. Note, however that CASIO makes no guarantees about the operation
of any Ultra High Speed Type SD memory card used with this camera.
30
Quick Start Basics
Loading...
+ 202 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.