Casio EX-100F User's Guide

Digital Camera
EN
User’s Guide
Thank you for purchasing this CASIO product.
• Before using it, be sure to read the precautions contained in this User’s Guide.
• Keep the User’s Guide in a safe place for future reference.
• For the most up-to-date information about this product, visit the official EXILIM Website at http://www.exilim.com/

Accessories

As you unpack your camera, check to make sure that all accessories shown below are included. If anything is missing, contact your original retailer.
Rechargeable lithium ion
battery (NP-130A)
Micro USB cable Basic Reference Neck strap
Lens cap
USB-AC adaptor
(AD-C53U)
Power cord
*
* The shape of the power cord plug varies according to the country or geographic
area where the camera is sold.
2

Attaching and Removing the Lens Cap

Attachment
Removal
Mark
Attach the lens cap with the large blades on the left and right.
1
To shorten
To lengthen
The lens cap opens and closes automatically in accordance with the lens position, so you can leave it in place, if you want. Make sure the lens cap is attached to the lens so the dot mark on the cap is upwards, with the large blades of the cap on the left and right. If the cap is in the wrong position, its blades can cause partial darkening of images when shooting with flash.

Attaching the Neck Strap to the Camera

• Attach either end of the strap to the two strap rings on the sides of the camera as shown in the illustration.
• After you are finished pull on the strap to test it and to make sure it does not come loose.
. Adjusting the Length of the Strap
You can adjust the length of the strap so it can be used as a neck strap or a shoulder strap.
1. Pull the strap out at the center
of the buckle in the direction indicated by
.
2. Pull the strap in one of the
directions indicated by the illustration to adjust the length.
3

Read this first!

• The contents of this manual are subject to change without notice.
• The contents of this manual have been checked at each step of the production process. Feel free to contact us if you notice anything that is questionable, erroneous, etc.
• Any copying of the contents of this User’s Guide, either in part or its entirety, is forbidden. Except for your own personal use, any other use of the contents of this manual without the permission of CASIO COMPUTER CO., LTD. is forbidden under copyright laws.
• CASIO COMPUTER CO., LTD. shall not be held liable for any damages or lost profits suffered by you or any third party due to the use or malfunction of this product.
• CASIO COMPUTER CO., LTD. shall not be held liable for any damages or lost profits caused by loss of memory contents due to malfunction, repair, or any other reason.
• Note that the example screens and product illustrations shown in this User’s Guide may differ somewhat from the screens and configuration of the actual camera.
LCD Panel
The liquid crystal panel of the monitor screen uses high-precision technology that provides a pixel yield in excess of 99.99%. This means that some very small number of pixels may not light or may remain lit at all times. This is due to the characteristics of the liquid crystal panel, and does not indicate malfunction.
Take test shots
Before shooting your final image, shoot a test shot to ensure that the camera is recording correctly.
4

Contents

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Attaching and Removing the Lens Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Attaching the Neck Strap to the Camera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Read this first! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

General Guide 11

Monitor Screen Contents and How to Change Them 13

Quick Start Basics 17
What you can do with your CASIO camera . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Tilting the Monitor Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Using the Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
First, charge the battery prior to use.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
To load the battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Charge the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Configuring Basic Settings the First Time You Turn On the Camera. . . . . . . . 27
Preparing a Memory Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Supported Memory Cards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
To load a memory card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
To format (initialize) a new memory card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Turning the Camera On and Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Holding the Camera Correctly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
To shoot a snapshot. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Selecting an Auto Recording Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
To shoot a snapshot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Viewing Snapshots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Deleting Snapshots and Movies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Snapshot Shooting Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Snapshot Tutorial 42
Selecting the Recording Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Using the Control Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Configuring Camera Settings with the Function Ring . . . . . . . . . . . . . . . . . . . . . 45
Using the Self-timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Self-timer) . . 46
Adjusting White Balance . . . . . . . . . . . . . . . . . . . . . . . . . . (White Balance) . . 47
Selecting a Focus Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Focus) . . 49
Specifying ISO Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (ISO) . . 53
Recording Beautiful Portraits . . . . . . . . . . . . . . . . . . . . . . . . . . (Make-up) . . 54
Correcting Image Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . (Exposure) . . 55
Using Flash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Flash) . . 56
Specifying the Metering Mode . . . . . . . . . . . . . . . . . . . . . . . . . (Metering) . . 58
Shooting with Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Monitor Screen Information when Zooming . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
5
Contents
Zooming with Super Resolution . . . . . . . . . . . . . . . . . . . . . . . . (Zoom (SR)) . . . 63
Expanding the Zoom Range to Shoot Clearer Snapshots . (Multi SR Zoom). . . 64
Shooting with Bracketing . . . . . . . . . . . . . . . . . . . .(Intelligent Bracketing) . . 64
Shooting Multiple Images Over a Specified Period . . . . . . . (Interval Shot) . . 65
Shooting a Burst of Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (CS) . . 68
Shooting with High Speed CS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Using High Speed CS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(60 fps) . . . 69
Shooting with Prerecord CS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Using Continuous Shutter with Auto Focus . . . . . . . . . . . . . . . . . . (AF CS) . . . 73
Triggering a Self-timer Operation with Motion . . . . . . . . .(Motion Shutter) . . 74
Configuring Motion Shutter Settings . . . . . . . . . . . . . . . . . (Motion Shutter). . . 76
Shooting with Artistic Effects . . . . . . . . . . . . . . . . . . . . . . . . . . . (Art Shot) . . 77
Saving a Second Normal Image When
Shooting with HDR Art . . . . . . . . . . . . . . . . . . . . . . . . . .(Double (HDR Art)). . . 79
Creating and Using Your Own Setups . . . . . . . . . . . . . . . . (Custom Shot) . . 80

Recording Movies 82
To record a movie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Audio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Recording a High-definition Movie. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Recording a High Speed Movie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Using Prerecord Movie . . . . . . . . . . . . . . . . . . . . . . . . (Prerecord (Movie)) . . 87
Recording a Time Lapse Movie . . . . . . . . . . . . . . . . . . . . . . (Time Lapse) . . 89
Shooting a Snapshot while Shooting a Movie . . . . . (Snapshot In Movie) . . 92

Using BEST SHOT 93
To shoot with BEST SHOT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Recording Beautiful Portraits . . . . . . . . . . . . . . . . . . . . . . . . . . (Make-up) . . 95
Shooting Three Versions of an Image with
Different Skin Tone Settings . . . . . . . . . . . . . . . . . . . . . . . (Make-up BKT) . . 96
Shooting a Movie Manually . . . . . . . . . . . . . . . . (Manual Exposure Movie) . . 97
Rotating an Image 180 Degrees . . . . . . . . . . . . . . . . . . . . (Flipped Image) . . 98
Rotating an Image 180 Degrees when
Recording CS Images . . . . . . . . . . . . . . . . . . . . . . . . . (Flipped CS Image) . . 98
Shooting with Triple Shot. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Shooting with a Blurred Background . . . . . . . . . . . (Blurred Background) . 101
Shooting with Full Focus Macro . . . . . . . . . . . . . . . . (All-In-Focus Macro) . 102
Digitally Correcting for Overexposure and Underexposure . . . . . . (HDR) . 103
Shooting with High Speed Anti Shake . . . . . . . . . . . . . . . (HS Anti Shake) . 104
Shooting Bright Images in the Dark without Flash . . . . . . (HS Night Shot) . 104
Shooting with Priority on Subject Faces . . . . . . . . . . . (HS Best Selection) . 105
Shooting a Panorama Image . . . . . . . . . . . . . . . . . . . . .(Slide Panorama) . 106
Shooting with a Super Wide Angle of View . . . . . . . . . . . . . . (Wide Shot) . 108
Using a TV Screen to Shoot Snapshots . . . . . . . . . . . . (HDMI TV Output) . .111
6
Contents

Advanced Settings (REC MENU) 113
Configuring Recording Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Shooting a Burst of Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (CS) . 114
Using a Smartphone as a Camera Remote Controller . (Remote Capture) . 114 Displaying Functions Assigned to the Control Dial
and Function Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (EX Finder) . 115
Configuring Motion Shutter Settings . . . . . . . . . . . . . . . . . (Motion Shutter) . 115
Assigning a Recording Function
to the Front Shutter Button . . . . . . . . . . . . . . . . . . . . . . . . . (Front Shutter) . 116
Assigning Functions to the Control Dial . . . . . . . . . . . . . (Key Customize) . 117
Using the Self-timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Self-timer) . 118
Reducing Light Intensity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (ND Filter) . 118
Correcting Image Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . (Exposure) . 119
Adjusting White Balance . . . . . . . . . . . . . . . . . . . . . . . . . . (White Balance) . 119
Specifying ISO Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (ISO) . 119
Specifying the ISO Sensitivity Upper Limit . . . . . . . . . . . . (ISO High Limit) . 120
Selecting a Focus Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Focus) . 121
Specifying the Auto Focus Area . . . . . . . . . . . . . . . . . . . . . . . . . (AF Area) . 121
Shooting with Face Detection . . . . . . . . . . . . . . . . . . . . . (Face Detection) . 123
Recording Beautiful Portraits . . . . . . . . . . . . . . . . . . . . . . . . . . (Make-up) . 124
Shooting with Continuous Auto Focus . . . . . . . . . . . . . . (Continuous AF) . 124
Specifying the Metering Mode . . . . . . . . . . . . . . . . . . . . . . . . . (Metering) . 124
Reducing the Effects of Camera and
Subject Movement . . . . . . . . . . . . . . . . . . . . . . . . .(Anti-shake Functions) . 125
To select the snapshot image size . . . . . . . . . . . . . . . . . . . . (Image Size) . 126
Specifying Snapshot Image Quality . . . . . . . . . . . . . . . . . (Image Quality) . 128
Movie Image Quality Settings . . . . . . . . . . . . . . . . . . . . . . (Movie Quality) . 128
Optimizing Image Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . (Lighting) . 130
Controlling Image Sharpness . . . . . . . . . . . . . . . . . . . . . . . . . (Sharpness) . 130
Controlling Color Saturation . . . . . . . . . . . . . . . . . . . . . . . . . . (Saturation) . 130
Adjusting Image Contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(Contrast) . 131
Specifying Flash Intensity . . . . . . . . . . . . . . . . . . . . . . . . . (Flash Intensity) . 131
Zooming with Super Resolution . . . . . . . . . . . . . . . . . . . . . . .(Zoom (SR)) . 131
Turning Digital Zoom On or Off . . . . . . . . . . . . . . . . . . . . . . (Digital Zoom) . 131
Using the Auto Focus Assist Light . . . . . . . . . . . . . . . . . (AF Assist Light) . 132
Saving a Second Normal Image
When Shooting with HDR Art . . . . . . . . . . . . . . . . . . . (Double (HDR Art)) . 132
Reducing Wind Noise during Movie Recording . . . . . . . (Wind Noise Cut) . 132
Turning on Image Review . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Review) . 133
Using Icon Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Icon Help) . 134
Changing the Monitor Screen when Recording . . . . . . . . . (Shooting Info) . 134
Configuring Power On Default Settings . . . . . . . . . . . . . . . . . . . (Memory) . 137
7
Contents

Viewing Snapshots and Movies 138
Viewing Snapshots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
Viewing a Movie. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
Viewing a Panorama Image. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Viewing Continuous Shutter Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
Deleting Continuous Shutter Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Dividing Up a Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Copying a Group Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Scrolling Images at High Speed or by Recording Date . . . . . . . . . . . . . . . . . 146
Zooming an On-screen Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Displaying the Image Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
Changing Available Image Menu Options . . . . . . . . (Image Menu Options) . . 148
Viewing Snapshots and Movies on a TV Screen. . . . . . . . . . . . . . . . . . . . . . 149

Other Playback Functions (PLAY MENU) 151
Assigning a Function to the Front Shutter Button . . . . . . . . (Front Shutter) . 151
Sending a Snapshot or Movie File from Camera Memory
to a Smartphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(Send to phone) . 151
Viewing Snapshots and Movies in Camera Memory
on a Smartphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (View on phone) . 152
Playing a Slideshow on the Camera . . . . . . . . . . . . . . . . . . . . (Slideshow) . 152
Transferring Music from Your Computer to Camera Memory . . . . . . . . . . . . . . 154
Using Snapshots to Create a Movie . . . . . . . . . . . . . . . . . . .(Make Movie) . 155
Editing a Movie on the Camera . . . . . . . . . . . . . . . . . . . . .(Movie Editing) . 156
To merge two movies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Movie Merge) . 158
Creating a Snapshot of Movie Frames . . . . . . . . . . . . . (MOTION PRINT) . 158
Optimizing Image Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . (Lighting) . 159
Adjusting White Balance . . . . . . . . . . . . . . . . . . . . . . . . . . (White Balance) . 159
Adjusting the Brightness of an Existing Snapshot . . . . . . . . . (Brightness) . 160
Selecting Images for Printing . . . . . . . . . . . . . . . . . . . . . . (DPOF Printing) . 160
Protecting a File Against Deletion . . . . . . . . . . . . . . . . . . . . . . . . . (Protect) . 161
Editing the Date and Time of an Image . . . . . . . . . . . . . . . . . (Date/Time) . 163
Rotating an Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(Rotation) . 163
Resizing a Snapshot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Resize) . 164
Cropping a Snapshot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Trimming) . 164
Copying Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Copy) . 165
Combining CS Images into a Single Still Image . . . . . . . . (CS Multi Print) . 165
Dividing Up a Continuous Shutter Group . . . . . . . . . . . . . . (Divide Group) . 166
Editing a CS Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Edit Group) . 166
Changing Available Image Menu Options . . . . . . .(Image Menu Options) . 166
8
Contents

Establishing a Wireless LAN Connection 167
Wireless LAN Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
Getting Ready to Establish a Connection between a Smartphone and Your
Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
Installing the EXILIM Remote App on Your Smartphone . . . . . . . . . . . . . . . . . 169
Establishing a Wireless LAN Connection for the First Time . . . . . . . . . . . . . . . 170
Using a Smartphone as a Camera Remote Controller . (Remote Capture) . 171
Configuring the Front Shutter Button to Send Images . . . . . (Quick Send) . 171
Sending a Snapshot or Movie File from Camera Memory
to a Smartphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(Send to phone) . 172
Resizing Snapshots before Sending Them
to a Smartphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Resize before send) . 173
Viewing Snapshots and Movies in Camera Memory
on a Smartphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (View on phone) . 174

Printing 175
Printing Snapshots. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
Using DPOF to Specify Images to be Printed
and the Number of Copies . . . . . . . . . . . . . . . . . . . . . . . . (DPOF Printing) . 175

Using the Camera with a Computer 180
Things you can do using a computer... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
Using the Camera with a Windows Computer . . . . . . . . . . . . . . . . . . . . . . . . 181
Viewing and Storing Images on a Computer. . . . . . . . . . . . . . . . . . . . . . . . . . . 181
Playing Movies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
Using the Camera with a Macintosh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
Connecting the Camera to Your Computer and Saving Files . . . . . . . . . . . . . . 185
Playing a Movie. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187
Files and Folders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
Memory Card Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189
9
Contents

Other Settings (SETTING) 191
Enabling Power Saving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (ECO Mode) . 191
Adjusting Monitor Screen Brightness . . . . . . . . . . . . . . . . . . . . . . (Screen) . 191
Resizing Snapshots before Sending Them
to a Smartphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Resize before send) . 192
Configuring Camera Sound Settings . . . . . . . . . . . . . . . . . . . . . (Sounds) . 192
Creating an Image Storage Folder . . . . . . . . . . . . . . . . . . (Create Folder) . 193
Time Stamping Snapshots . . . . . . . . . . . . . . . . . . . . . . . . . . .(Timestamp) . 193
Auto Image Orientation Detection and Rotation . . . . . . . . . . (Auto Rotate) . 194
Specifying the File Name Serial Number Generation Rule . . . . . (File No.) . 194
Configuring Sleep State Settings . . . . . . . . . . . . . . . . . . . . . . . . . . (Sleep) . 195
Configuring Auto Power Off Settings . . . . . . . . . . . . . . . (Auto Power Off) . 195
Specifying the Operation when the Monitor Screen is Tilted . (Screen Tilt) . 196
Configuring [p] Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (PLAY) . 196
Disabling File Deletion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(Delete Key) . 196
Configuring World Time Settings . . . . . . . . . . . . . . . . . . . . . (World Time) . 197
Setting the Camera’s Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Adjust) . 198
Specifying the Date Style . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Date Style) . 198
Specifying the Display Language . . . . . . . . . . . . . . . . . . . . . . (Language) . 199
Selecting the HDMI Terminal Output Method . . . . . . . . . . . (HDMI Output) . 199
Changing the Camera Password
for Wireless LAN Connection . . . . . . . . . . . . . . . . . . . . (WLAN password) . 200
Formatting Built-in Memory or a Memory Card . . . . . . . . . . . . . . . (Format) . 201
Resetting the Camera to Factory Defaults . . . . . . . . . . . . . . . . . . . (Reset) . 201
Checking the Current Camera Firmware Version . . . . . . . . . . . . (Version) . 201

Appendix 202
Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202
Precautions During Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211
Power Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216
Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216
Battery Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217
Using the Camera in another Country . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217
Using a Memory Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 218
Reset Initial Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219
When things don’t go right... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
Display Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227
Number of Snapshots/Movie Recording Time . . . . . . . . . . . . . . . . . . . . . . . . 229
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231
10
Contents

General Guide

Mode dial (pages 34, 42, 82)
Zoom controller (pages 35, 59, 147)
Shutter button (pages 32, 34)
[ON/OFF] (Power) (pages 28, 32)
Front lamp (pages 46, 132)
Flash (page 56)
Strap rings (page 3)
Function ring (pages 45, 146)
Lens

Front shutter button (pages 116, 151, 171)

Microphones (page 83)

[0] (Movie) button (page 82)

[RING] button (pages 45, 146)

Speaker

Terminal cover

[HDMI OUT] HDMI output (Micro) (pages 111, 150)

[USB] port (pages 23, 25)

[SET] button (pages 44, 82, 113)

[MENU] button (pages 82, 113)

[p] (PLAY) button (pages 32, 38)

Back lamp (pages 24, 26, 32, 35,
57)

Control dial ([8][2][4][6]) (pages 12, 44, 82, 93, 113, 117)

Monitor screen (pages 13, 19, 32, 196)

Stand (pages 19, 21)
bq
br
bscl ck btcmcn
co
bl bpbnbm bo
Front Back
The numbers in parentheses indicate the pages where each item is explained.
321 4675
89bk
11
General Guide
. Control Dial
cr cpcq
Bottom

Battery/memory card slots (pages 22, 30)

Battery cover

Tripod hole Use this hole when attaching to a tripod.
[8] [2] [4] [6] : Press the applicable button (up, down, left, right).
Control dial
In addition to using the up, down, left, and right buttons, you can also use the control dial to perform operations.
• Depending on the function, certain operations cannot be performed using the control dial.
12
General Guide

Monitor Screen Contents and How to Change Them

NOTE
bt
cn
cl ck
cm
cp
cq
co
brbs bq
13567824
bk
9
bl bm
bo bp
bn
The monitor screen uses various indicators, icons, and values to keep you informed of the camera’s status.
• The sample screens in this section are intended to show you the locations of all the indicators and figures that can appear on the monitor screen in various modes. They do not represent screens that actually appear on the camera.
. Snapshot Recording (1 Shot)
Snapshot image size/Quality (pages 126, 128)
Movie quality (FHD/STD movie)
(pages 82, 85)/ Recording speed (high speed movie) (page 85) AF Area (page 121)
Focal distance

(Converted to 35 mm film format.) (page 61) Anti-shake Functions (page 125)

Timestamp indicator (page 193)

Histogram (page 134)

Front shutter button function (page 116)

ND Filter (page 118)

Date/Time (pages 27, 198)

Focus frame (pages 35, 122)
Self-timer mode (page 46)
Face Detection (page 123)
Recording mode (page 34)
Image deterioration indicator/
Zoom (SR) indicator (page 62) Remaining movie memory
capacity (page 82) Remaining snapshot memory
capacity (page 229)

Electronic level (page 135)

Battery level indicator (page 27)

Metering mode (page 58)

Flash (page 56)

Exposure compensation (page 55)

Make-up (page 54)

ISO sensitivity (page 53)

Focus mode (page 49)

White balance (page 47)

• Depending on recording settings, the aperture, shutter speed, and ISO sensitivity values may not appear on the monitor screen. These values will be red if the Auto Exposure (AE) is not correct for some reason.
Monitor Screen Contents and How to Change Them
13
. Snapshot Recording (Burst Shooting)
1243
6
7
8
5
6
5
42
3
7
8
1
Continuous Shutter (CS) speed (page 68)
Recording mode (page 34)
Remaining snapshot memory capacity
(page 229) Allowable CS time*/number of CS images
(page 68)
* It is not displayed while shooting with
Prerecord CS.
Remaining movie memory capacity (page 230)
Continuous Shutter mode (page 68)
Prerecord CS shots (page 71)
Maximum CS shots (page 68)
. Movie Recording
Snapshot recording mode (Snapshot In Movie)
(page 92) Audio recording disabled (page 85)
Recording mode (page 82)
Movie recording time (page 82)
Remaining movie memory capacity (page 82)
Movie recording in progress (page 82)
Movie quality (FHD/STD movie)
(pages 82, 85)/ Recording speed (high speed movie) (page 85) Remaining snapshot memory capacity
(page 229)
Monitor Screen Contents and How to Change Them
14
. Snapshot Viewing
2413
6
5
8
bn blbo
br bq bp
bt bs
ck
cl
cm
7
9 bk
bm
1 2
3
File type
Protect indicator (page 161)
Snapshot image size
(page 126) Folder name/file name
(page 188)
. Movie Playback
Snapshot image quality (page 128)
Recording mode (page 34)
ND Filter (page 118)
Histogram (page 134)
Front shutter button function (page 151)
Wireless LAN connection status

(page 170) Date/time (page 198)

Metering mode (page 58)

White balance (page 159)

Battery level indicator (page 27)

Flash (page 56)

Exposure compensation (page 55)

Shutter speed

Aperture value

ISO sensitivity (page 53)

Focal distance

(Converted to 35 mm film format.) Make-up (Smooth Skin) (pages 54, 95, 96)

Make-up (Skin Tone) (pages 54, 95, 96)

No audio data available
Movie recording time (page 138)
Recording mode/Movie quality/speed
(pages 82, 85, 85)
Monitor Screen Contents and How to Change Them
15
. Configuring Monitor Screen Settings
[8] (DISP)
Each press of [8] (DISP) will cycle through display settings that display or hide on-screen information. You can configure separate settings for the REC mode and PLAY mode.
REC mode
Information on Displays setting information.
Information off Hides setting information.
PLAY mode
Information on
Displays settings when shooting, current date and time, histogram (page 134), and other information.
Information off No information displayed when shooting.
With thumbnails
Shows images that come before and after the current image.
Monitor Screen Contents and How to Change Them
16

Quick Start Basics

*See page 64 for more information.
*See page 74 for more information.
*See page 96 for more information.
*See page 98, 98 for more information.
*See page 65 for more information.

What you can do with your CASIO camera

Your CASIO camera is packed with a powerful selection of features and functions to make recording of digital images easier, including the following main functions.
Intelligent Bracketing
You can use this function to shoot a series of images, slightly changing the camera setup with each shot.
Motion Shutter
You can control operation of the self-timer from a distance by waving your hand, which makes it easier to shoot self-portraits from a distance.
Make-up Bracketing (Make-up BKT)
Make-up Bracketing (Make-up BKT) lets you shoot three versions of the same image with the press of the shutter button, each with a different Skin Tone setting.
Flipped Image, Flipped CS Image
When shooting stars, birds, or other distant subjects with the camera attached to an astronomical telescope or to a monocle device, the recorded image may be vertically or horizontally flipped. This lets you record the image at it actually appears to the eye.
Interval Shot
You can record a series of images over a specified period. This function is useful when recording the movement of stars, a blooming flower, etc.
17
Quick Start Basics
Time Lapse Movie
*See page 89 for more information.
*See page 77 for more information.
*See page 34 for more information.
*See page 167 for more information.
You can use this function to record movies of natural events that occur over time, to speed up the flow of traffic in a city scene, or to record other similar types of movies.
Art Shot
A variety of artistic effects help to make even common, ordinary subjects become more novel and exciting. “Art Shot” provides the following effects: HDR Art, Toy Camera, Soft Focus, Light Tone, Pop, Sepia, Monochrome, Miniature, Fisheye, Sparkling Shot, Crystal Ball.
Premium Auto Pro
Select Premium Auto Pro recording and the camera automatically determines whether you are shooting a subject or scenery, and other conditions. Premium Auto Pro delivers higher image quality than standard Auto.
Wireless LAN Connection
Turns your smartphone into a camera remote controller and allows you to send images recorded with your camera to your smartphone.
18
Quick Start Basics
IMPORTANT!
NOTE

Tilting the Monitor Screen

180 degrees
55 degrees
90 degrees
The monitor screen can be tilted upwards up to 180 degrees or downwards up to 55 degrees.
. Tilting the Monitor Screen
As shown in the illustration, you can tilt the monitor screen by opening it from the bottom or from the top.
• Under factory default settings, the camera will turn on automatically whenever the monitor screen is tilted. See page 196 for information about configuring the camera so it does not turn on when the monitor screen is tilted upwards.
• When returning the monitor screen to the back of the camera, take care so you do not catch your fingers between the top or bottom of the monitor screen and the camera.
• Do not subject the monitor screen to strong impact. Doing so can damage it.
• Be sure to return the monitor screen to its normal position to the back of the camera when you are not using it.
• Whenever placing the camera on a tabletop or other surface to shoot, be sure to pull out the stand to keep it from falling over (page 21).
19
Quick Start Basics
. Returning the Monitor Screen to Its Normal Position
1. Hold the bottom of the
monitor screen and rotate it, or press the top of the monitor screen to return it to its normal position.
2. Slide the monitor screen up as far as it will go.
. What you can do with the camera...
Shoot self-portraits
You can position the monitor screen so it faces in the same direction as the lens, for easy composition of self-portraits. You can also use a stand on the back of the camera to keep the camera upright when placed on a tabletop or other surface.
20
Quick Start Basics
IMPORTANT!
Low-angle shots High-angle shots
Stand
The tilt angle of the monitor screen can be adjusted for each composition of
You can tilt the monitor screen in a way that allows you to shoot from high angles.
images from various low angles.

Using the Stand

Your camera has a built-in stand. You can pull out the stand and keep the camera stable on a tabletop or other surface while the monitor screen is tilted upwards 180 degrees. When using the camera on a tabletop or other surface for landscape (horizontal) orientation shots, you can adjust the vertical angle of the camera somewhat by changing how far you pull out the stand.
• When using the camera on a tabletop or other surface for portrait (vertical) orientation shots, pull the stand out as much as possible so the camera is stable. Pulling the stand out part way in this case can cause the camera to become unstable and fall over.
• Even when using the stand to adjust the vertical angle of the camera while shooting with landscape (horizontal) orientation, take care to extend the stand far enough to avoid camera instability, which can cause it to fall over.
• Whenever using the stand, make sure that the location where you place the camera is stable and relatively level.
21
Quick Start Basics

First, charge the battery prior to use.

Battery cover
CASIO logo
Stopper
Battery
OK
NG
Note that the battery of a newly purchased camera is not charged. Perform the steps below to load the battery into the camera and charge it.
• Your camera requires a special CASIO rechargeable lithium ion battery (NP-130A) for power. Never try to use any other type of battery.

To load the battery

1. Open the battery cover.
2. Load the battery.
With the CASIO logo on the battery facing downwards (in the direction of the lens), hold the stopper next to the battery in the direction indicated by the arrow as you slide the battery into the camera. Press the battery in until the stopper secures it in place.
3. Close the battery cover.
22
Quick Start Basics
To replace the battery
Stopper
USB-AC adaptor (AD-C53U)
u mark of the small (micro USB) connector facing the monitor screen side of the camera.
[USB] port
Micro USB cable (included with camera)
Power cord
1. Open the battery cover and
remove the current battery.
2. Load a new battery.

Charge the Battery

You can use either of the two following methods to charge the camera’s battery.
• USB-AC adaptor
• USB connection to a computer (Using the included micro USB cable.)
. To charge with the USB-AC adaptor
The adaptor lets you charge the battery while it is loaded in the camera. While the camera is turned off, connect in the sequence shown below. Charging time: Approximately 240 minutes
2
3
1
4
• When disconnecting the USB-AC adaptor from the camera, be sure to disconnect from the camera first.
23
Quick Start Basics
IMPORTANT!
Back lamp
• A battery that has not been used for a long time and/or ambient temperature can cause charging to take longer than normal. These conditions may also cause the back lamp to flash red. If this happens, refer to page 216.
• Make sure that you insert the cable connector into the [USB] port until you feel it click securely into place. Failure to insert the connector fully can result in poor communication or malfunction.
• Note that even while the connector is fully inserted, you still will be able to see the metal part of the connector as shown in the illustration.
• Pressing [ON/OFF] (Power) while the USB-AC adaptor is connected to the camera will turn on the camera with power being supplied by the battery. Because of this, charging will stop.
• The USB-AC adaptor will become warm during charging. This is normal and does not indicate malfunction.
• The shape of the power plug depends on each country or geographic area.
Back Lamp Operation
Lamp Status Description
Lit Red Charging
Abnormal ambient temperature,
Flashing Red
USB-AC adaptor problem, or battery problem (page 216)
Off Charging complete
24
Quick Start Basics
. To charge using a USB connection to a computer
2
USB
1
Micro USB cable
(included with camera)
u mark of the small (micro USB) connector facing the monitor screen side of the camera.
[USB] port
USB port
Computer
(power turned on)
USB connection lets you charge the battery while it is loaded in the camera. While the camera is turned off, connect in the sequence shown below (
• If the camera is on, press [ON/OFF] (Power) to turn it off before connecting it to your computer.
IMPORTANT!
• The first time you connect the camera to your computer with the USB cable, an error message may appear on your computer. If this happens, disconnect and then reconnect the USB cable.
• A battery that has not been used for a long time, certain types of computers, and connection conditions can cause charging to take longer than normal. These conditions may also cause the back lamp to flash red. If this happens, refer to page
216.
• For faster charging, use of the supplied USB-AC adaptor is recommended.
• You cannot use the camera to shoot images while it is being charged over a computer USB connection. If you want to shoot with the camera, disconnect the USB cable.
• If you turn on the camera while charging over a USB connection to a computer is in progress, the camera will establish a USB connection with the computer. Though charging normally should continue at this time, certain types of computers or connection environments may stop charging if supply power is low. This will be indicated by the camera’s back lamp lighting green.
• Charging is not performed while the connected computer is in the hibernate mode.
, 
).
25
Quick Start Basics
Back Lamp Operation
Back lamp
Lamp Status Description
Lit Red, (Lit/Flashing Amber)
Charging
Abnormal ambient temperature,
Flashing Red
charging taking abnormally long, or battery problem (page 216)
Off, (Lit Green) Charging complete
• The information in parentheses in the above table shows the lamp status while the camera is turned on during charging.
Other Charging Precautions
• With the two charging methods described above, you can charge the camera’s battery (NP-130A) without removing it from the camera. You also can charge the battery using an optionally available charger unit (BC-130L). Never use any other type of charger device. Attempting to use a different charger can result in unexpected accident.
• This model can be charged only via from USB 2.0 specification USB port only.
• USB charging devices and power supply devices are subject to fixed standards. Use of an inferior device or a device that is not up to standard can cause malfunction and/or failure of your camera.
• Operation is not guaranteed in the case of a computer built or modified by you. Even in the case of a commercially available computer, certain USB port specifications may make it impossible to charge via the USB cable.
• A battery that is still warm immediately after normal use may not charge fully. Give the battery time to cool before charging it.
• A battery discharges slightly even when it is not loaded in the camera. Because of this, it is recommended that you charge the battery immediately before you need to use it.
• Charging the camera’s battery may cause interference with TV and radio reception. If this happens, plug the USB-AC adaptor into an outlet that is further away from the TV or radio.
• Actual charging time depends on current battery capacity and charging conditions.
• Do not use the USB-AC adaptor with any other device.
• Never use the power cord with another device.
• Use only the USB-AC adaptor and USB cable specified in this manual for charging. Use of any other type of devices may result in improper charging.
26
Quick Start Basics
Checking Remaining Battery Power
IMPORTANT!
As battery power is consumed, a battery indicator on the monitor screen indicates remaining power as shown below.
Remaining Power High Low
Battery Indicator ***
Indicator Color White * White * Red * Red
indicates battery power is low. Charge the battery as soon as possible.
Recording is not possible when is indicated. Charge the battery immediately.
• The level shown by the battery indicator may change when you switch between the REC mode and PLAY mode.
• Leaving the camera for about 30 days with no power supplied while the battery is dead will cause its date and time settings to be cleared. A message telling you to configure time and date settings will appear the next time you turn on the camera after restoring power. When this happens, configure date and time settings (page
198).
• See page 234 for information about battery life and number of shots.
Battery Power Conservation Tips
• Entering the “ECO Mode” (page 191) enables low-power operation. Note that low­power operation decreases monitor screen brightness.
• When you do not need to use the flash, select ? (Flash Off) for the flash setting (page 56).
• Enable the Auto Power Off (page 195) and the Sleep features (page 195) to protect against wasting battery power when you forget to turn off the camera.
• Select “Off” for “Continuous AF” (page 124).

Configuring Basic Settings the First Time You Turn On the Camera

The first time you load a battery into the camera, a screen appears for configuring the display language, date, and time settings. Failure to set the date and time correctly will cause the wrong date and time data to be recorded with images.
• A screen for language selection will not appear in step 2 of the procedure below if you purchased a camera intended for the Japanese market. To change the display language from Japanese in this case, use the procedure under “Specifying the Display Language (Language)” (page 199). Note that a version of this manual in the language you select may not be included with a camera intended for the Japanese market.
• Camera models sold in certain geographic areas may not support display language selection.
27
Quick Start Basics
1. Press [ON/OFF] (Power) to turn on the
NOTE
[ON/OFF] (Power)
camera.
2. Use [8], [2], [4], and [6] to select the
language you want and then press [SET].
3. Use [8] and [2] to select a date style and then press [SET].
Example: July 10, 2016 YY/MM/DD DD/MM/YY MM/DD/YY
* 16/7/10 * 10/7/16 * 7/10/16
4. Set the date and the time.
Use [4] and [6] to select the setting you want to change and then use [8] and [2] to change it. To switch between 12-hour and 24-hour format, select “24h” and then use [8] and [2] to change the setting.
5. After setting the date and time, use [4] and [6]
to select “Apply” and then press [SET].
If you make a mistake configuring display language, date, or time settings with the above procedure, refer to the following pages for information about how to correct the settings.
– Display language: page 199 – Date and time: page 198
• Each country controls its local time offset and the use of summer time, and so they are subject to change.
• Removing the battery from the camera too soon after configuring time and date settings for the first time can cause the settings to be reset to their factory defaults. Do not remove the battery for at least 24 hours after configuring settings.
28
Quick Start Basics

Preparing a Memory Card

Though the camera has built-in memory that can be used to store images and movies, you probably will want to purchase a commercially available memory card for greater capacity. The camera does not come with a memory card. Images recorded while a memory card is loaded are saved to the memory card. When no memory card is loaded, images are saved to built-in memory.
• For information about memory card capacities, see page 229.

Supported Memory Cards

– SD Memory Card – SDHC Memory Card – SDXC Memory Card
Use one of the above types of memory card.
• The above are supported memory card types as of May 2015.
• This camera supports use of SD memory cards of the following types and capacities: SD memory cards up to 2GB, SDHC memory cards from 2GB up to 32GB, SDXC memory cards from 32GB up to 2TB. Note that the ability to use any particular card with this camera, even if it satisfies the above capacity and type requirements, is not guaranteed.
. Memory Card Handling Precautions
Certain types of memory cards can slow down processing speeds. In particular, high­quality movies may not be able to be stored correctly. A slow memory card can take too much time to record data and result in breaks in the image and/or audio during playback. When this happens a yellow “Y” indicator will appear on the monitor screen.
29
Quick Start Basics
IMPORTANT!

To load a memory card

Front Back
Back
1. Press [ON/OFF] (Power) to turn
off the camera and then open the battery cover.
2. Load a memory card.
Positioning the memory card so its back is facing upwards (towards the monitor screen side of the camera), slide it into the card slot all the way in until you hear it click securely into place.
3. Close the battery cover.
• Never insert anything besides a supported memory card (page 29) into the memory card slot.
• Should water or any foreign object ever get into the card slot, immediately turn off the camera, remove the battery, and contact your retailer or nearest CASIO authorized service center.
30
Quick Start Basics
To replace the memory card
Back lamp
Press the memory card and then release it. This will cause it to pop out of the memory card slot slightly. Pull the card out the rest of the way and then insert another one.
• Never remove a card from the camera while the back lamp is flashing green. Doing so can cause the image save operation to fail and even damage the memory card.

To format (initialize) a new memory card

Format a memory card on the camera before using it for the first time.
IMPORTANT!
• Formatting a memory card that already has snapshots or other files on it, will delete its contents. Normally you do not need to format a memory card again. However, if storing to a card has slowed down or if you notice any other abnormality, re-format the card.
• Be sure to use the camera to format a memory card. Formatting a card on a computer will result in a non-SD standard format, which can greatly slow down processing time and cause compatibility, performance, and other problems.
1. Turn on the camera and press [MENU].
2. Press [4], use [8] and [2] to select the “
press [6].
¥
SETTING” tab, and then
3. Use [8] and [2] to select “Format” and then press [SET].
4. Use [8] and [2] to select “Format” and then press [SET].
5. Use [8] and [2] to select “Yes” and then press [SET].
31
Quick Start Basics
NOTE

Turning the Camera On and Off

[p] (PLAY)
Back lamp
[ON/OFF] (Power)
Shutter button
Monitor screen
. To turn power on
Pressing [ON/OFF] (Power) enters the REC mode so you can record images. Pressing [p] (PLAY) while in the REC mode enters the PLAY mode, which you can use to view snapshots (page 38) and movies (page 138).
• You also can turn on the camera by pressing [p] (PLAY) or by tilting the monitor screen.
• Pressing the shutter button while in the PLAY mode returns to the REC mode.
• Take care to ensure that nothing is restricting or coming into contact with the lens as it extends. Holding the lens with your hand so it cannot extend creates the risk of malfunction.
• About 10 seconds after you press [p] (PLAY) to enter the PLAY mode, the lens will retract into the camera.
• The Sleep function (page 195) or Auto Power Off (page 195) will turn off power automatically if you do not perform any operation for a preset amount of time.
• The camera will not turn on when you press [ON/OFF] (Power) or [p] (PLAY) while it is being charged over a computer USB connection (page 25).
. To turn off the camera
Press [ON/OFF] (Power).
• The camera can be configured so power turns off when the [p] (PLAY) button is pressed (page 196) or whenever the monitor screen is returned to its normal position (page 196).
32
Quick Start Basics
NOTE
IMPORTANT!

Holding the Camera Correctly

Horizontal Vertical
Hold the camera so the flash is above the lens.
Front lamp
Lens
Flash
Your images will not come out clearly if you move the camera when you press the shutter button. When pressing the shutter button, be sure to hold the camera as shown in the illustration, and keep it still by pressing your arms firmly against your sides as you shoot. Holding the camera still, carefully press the shutter button and take care to avoid all movement as the shutter releases and for a few moments after it releases. This is especially important when available lighting is low, which slows down the shutter speed.
• Take care that your fingers and the strap do not cover any of the areas indicated in the illustration.
• To keep the camera from falling, be sure to keep the strap around your neck, wrapped around your wrist, or hanging from your shoulder.
• Never swing the camera around by its strap.
• The supplied strap is intended for use with this camera only. Never use it for any other purpose.
• Shooting an image while the camera’s “Auto Rotate” setting is “On” will cause the playback image to be rotated automatically to the orientation the camera was in when the image was recorded (page 194).
• Take care to ensure that your fingers are not blocking or are not too close to the flash. Fingers can cause unwanted shadows when using the flash.
• The flash unit pops up automatically, so make sure your hand is not pressing down on it.
33
Quick Start Basics

To shoot a snapshot

P
Ÿ
Auto recording mode icon
Shutter button
Mode dial
[ON/OFF] (Power)
Remaining Snapshot Memory
Capacity (page 229)
Monitor screen
Front shutter button

Selecting an Auto Recording Mode

You can select one of two auto recording modes (Program Auto or Premium Auto Pro) according to your digital imaging needs.
Setting
Program
Auto
Premium
Auto Pro
REC Screen Icon Display
Description
This is the standard Auto recording mode.
With Premium Auto Pro recording, the camera automatically determines whether you are shooting a subject or scenery, and other conditions. Premium Auto Pro recording delivers higher image quality than Program Auto recording.
• Some of the settings configured automatically by Premium Auto Pro cannot be changed by you.
• It also requires more power (and runs down the battery quicker) than Program Auto.
1. Press [ON/OFF] (Power) to turn on the camera.
The camera will enter the REC mode.
• If the camera is in the PLAY mode, press the shutter button.
2. Align the mode dial with [P] (Program Auto) or [Ÿ] (Premium Auto
Pro) to select Auto recording mode.
34
Quick Start Basics

To shoot a snapshot

Appears when the camera detects it is stationary on a tripod.
w Wide Angle z Telephoto
Zoom controller
If the camera judges that CS shooting is required when shooting with Premium Auto Pro, it will automatically switch to an HS scene, and “Š” will appear on the monitor screen. With the HS scene, the camera will shoot a burst of images and combine them to form the final image. To avoid image blur, make sure that the camera and subject remain still until all of the images are shot.
Focus frameBack lamp
Half-press
Press part way.
Beep, beep (Image is in focus.)
1. Point the camera at the subject.
If you are shooting with Premium Auto Pro, text will appear at the bottom of the monitor screen describing the type of shot the camera has detected.
• You can zoom the image, if you want.
2. Half-press the shutter button to
focus the image.
When focus is complete, the camera will beep, the back lamp will light green, and the focus frame will turn green.
When you half-press the shutter button, the camera automatically adjusts exposure and focuses on the subject it is currently pointed at. Mastering how much pressure is required for a half-press and a full-press of the shutter button is an important technique for good­looking images.
35
Quick Start Basics
3. Continuing to keep the camera
Full-press
Snap (Image is recorded.)
Front shutter button
Press all the way.
[0] (Movie)
still, press the shutter button the rest of the way down.
This records the snapshot.
• With the initial factory default configuration of the camera when you purchase it, pressing the front shutter button will shoot a snapshot (page 116).
Recording a Movie
Press [0] (Movie) to start movie recording. Press [0] (Movie) again to stop movie recording. See the following pages for details. Standard movie (STD movie): page 82 High-definition movie (FHD movie): page 85 High speed movie (HS movie): page 85
. If the image does not focus...
If the focus frame stays red and the back lamp is flashing green, it means that the image is not in focus (because the subject is too close, etc.). Re-point the camera at the subject and try to focus again.
. Shooting with Auto
If the subject is not in the center of the frame...
“Focus lock” (page 52) is the name of a technique you can use when you want to shoot an image in which the subject to be focused on is not within the focus frame in the center of the screen.
To track the movement of a moving subject
Half-press the shutter button to follow and focus automatically on a moving subject. See “OTracking” (page 121) for more information.
36
Quick Start Basics
. Shooting with Premium Auto Pro
• Some menu items are not available while Premium Auto Pro is in use (page 113). Only the menu items whose settings can be configured will be displayed on the menus while Premium Auto Pro is in use.
• In addition to shutter speed, aperture, and ISO sensitivity, the camera automatically executes the following operation as required when shooting with Premium Auto Pro. – Continuous AF (page 124) – Face Detection (page 123) – HS Scene Shooting (page 35)
• Shooting with Premium Auto Pro can cause vibration and noise to occur due to lens operation. This does not indicate malfunction.
• When Shooting with Premium Auto Pro, the message “Processing Premium Auto.” may appear on the monitor screen. If you feel the camera is taking too long to process data, try shooting with standard Auto instead.
• In some cases, Premium Auto Pro may not be able to interpret the shooting environment correctly. If this happens, shoot with standard Auto.
• If “Š” is displayed, the camera will shoot a series of CS images and merge them into a final image. If you do not want to shoot CS images, select “Off” for the Control Panel (page 44) “HS Scene Shooting” item.
• Certain flash settings (page 56) can limit environmental factors detectable by Premium Auto Pro.
37
Quick Start Basics
NOTE

Viewing Snapshots

[p] (PLAY)
[6]
[6]
[4]
[4]
Use the following procedure to view snapshots on the camera’s monitor screen.
• For information about how to play back movies, see page 138.
• For information about images recorded using continuous shutter (CS), see page
140.
1. Turn on the camera and press
[p] (PLAY) to enter the PLAY mode.
• This will display one of the snapshots currently stored in memory.
• Information about the displayed snapshot also is included (page 15).
• You also can clear the information to view only the snapshot (page 16).
• You can zoom in on the image by rotating the zoom controller towards z ([) (page 147). If you are recording a snapshot that is very important to you, it is recommended that you zoom the image and check its details after recording it.
2. Use [4] and [6] to scroll between images.
• Holding down either button scrolls at high speed.
• Half-pressing the shutter button while in the PLAY mode or while a menu screen is displayed will switch directly to the REC mode.
38
Quick Start Basics

Deleting Snapshots and Movies

If memory becomes full, you can delete snapshots and movies you no longer need in order to free up storage and record more images.
IMPORTANT!
• Remember that a file (image) delete operation cannot be undone.
• For information about images recorded using continuous shutter (CS), see page
143.
• If you select “Disabled” for the “Delete Key” setting on the “¥SETTING” menu (page 196), the delete menu will not appear when you press [2] ( ) (Delete). You can delete files only while “Enabled” is selected for “Delete Key”.
. To delete a single file
1. Press [p] (PLAY) to enter the PLAY mode and then
press [2] ( ).
2. Use [4] and [6] to scroll through the files until the one
you want to delete is displayed.
3. Use [8] and [2] to select “Delete” and then press [SET].
• To delete other files, repeat steps 2 and 3.
• To exit the delete operation, press [MENU].
• If a CS group (page 140), interval shot group (page 140) or bracketing group (page 141) is displayed when you perform the above procedure, all of the images in the currently displayed group will be deleted.
. To delete specific files
1. Press [p] (PLAY) to enter the PLAY mode and then press [2] ( ).
2. Use [8] and [2] to select “Delete Files” and then press [SET].
• This displays a file selection screen.
3. Use [8], [2], [4], and [6] to move the selection boundary to the file
you want to delete, and then press [SET].
• This will select the check box in the lower left corner of the selected file’s image and move the blue boundary to the next image.
• To clear (deselect) a check box, move the blue boundary to the applicable file and then press [SET].
• You can enlarge the selected image before deleting it by rotating the zoom controller towards z ([).
4. Repeat step 3 to select other files, if you want. After you are finished
selecting files, press [MENU].
39
Quick Start Basics
5. Use [8] and [2] to select “Yes” and then press [SET].
• This deletes the files you selected.
• To cancel the delete operation, select “No” in step 5 and then press [SET].
. To delete all files
1. Press [p] (PLAY) to enter the PLAY mode and then press [2] ( ).
2. Use [8] and [2] to select “Delete All Files” and then press [SET].
3. Use [8] and [2] to select “Yes” and then press [SET] to delete all files.
This will cause the message “There are no files.” to appear.

Snapshot Shooting Precautions

Operation
• Never open the battery cover while the back lamp is flashing green. Doing so can result in the image you just shot being saved incorrectly, damage to other images stored in memory, malfunction of the camera, etc.
• If unwanted light is shining onto the lens, shade the lens with your hand when shooting an image.
Monitor Screen when Shooting Snapshots
• Subject brightness conditions can cause monitor screen response to slow and can cause digital noise in the monitor screen image.
• The image that appears on the monitor screen is for image composition. The actual image will be recorded at the quality set for the image quality setting (page 128).
Shooting Indoors under Fluorescent Lighting
• Minute flickering of fluorescent lighting can affect the brightness or color of an image.
Other Precautions
• The slower the shutter speed, the greater the possibility that noticeable noise will be generated in an image. Because of this, the camera automatically performs a noise reduction at slow shutter speeds. The noise reduction process causes it to take longer to record images at lower shutter speeds. The shutter speeds for which noise reduction is performed depend on the camera setup and shooting conditions.
• A noise reduction process is performed when ISO sensitivity is set to a high value. This can cause the camera to take relatively longer to be ready to shoot again after you press the shutter button. Do not perform any key operation while the image recording operation is in progress.
• Due to the characteristics of the imaging element used by the camera, very fast moving objects in an image may appear distorted.
40
Quick Start Basics
. Auto Focus Restrictions
• Any of the following can make proper focus impossible. – Solid color wall or other very low contrast subject – Strongly back lit subject – Very shiny subject – Blinds or other subject with a repeating horizontal pattern – Multiple subjects at varying distances from the camera – Subject in a dark location – Subject that is too far away for light from the AF assist light to reach – Camera movement while shooting – Fast-moving subject – Subjects outside the focus range of the camera
• If you cannot focus properly with Program Auto, try using focus lock (page 52) or Manual Focus (page 49).
41
Quick Start Basics

Snapshot Tutorial

Mode dial
bCM
F

Selecting the Recording Mode

Your camera has a variety of different recording modes. Before recording an image, rotate the mode dial to select the recording mode that suits the type of image you are trying to record.
PProgram Auto
Standard Auto recording mode. This is the mode you normally should use (page 34).
Ÿ Premium Auto Pro
With Premium Auto Pro recording, the camera automatically determines whether you are shooting a subject or scenery, and other conditions. Premium Auto Pro recording delivers higher image quality than standard Auto recording (page 34).
BEST SHOT
Simply select one of a collection of built-in sample scenes and the camera sets up automatically for beautiful images every time (page 93).
Art Shot
A variety of artistic effects help to make even common, ordinary subjects become more novel and exciting (page 77).
Intelligent Bracketing
You can use this function to shoot a series of images, slightly changing the camera setup with each shot (page 64).
Time Lapse / Interval Shot
You can use this function to record a movie that speeds up a sequence of changes in natural phenomena or the flow of traffic in a city scene (page 89), or to record a series of snapshots over time (page 65).
C Custom Shot
Custom Shot lets you register up to 12 different setups for instant recall whenever you need them (page 80).
42
Snapshot Tutorial
M M (Manual Exposure) mode
This mode gives you total control over aperture and shutter speed settings.
Press [SET] to open the Control Panel.
Use [8] and [2] to select (Aperture), and then press [SET].
Use [8] and [2] to change the aperture setting, and then press [4].
Use [8] and [2] to select (Shutter Speed), and then press [SET].
Use [8] and [2] to change the shutter speed setting, and then press [SET].
S S (Shutter Speed AE) mode
In this mode, you select the shutter speed and other settings are adjusted accordingly.
Press [SET] to open the Control Panel.
Use [8] and [2] to select (Shutter Speed), and then press [SET].
Use [8] and [2] to change the shutter speed setting, and then press [SET].
• You also can select the Exposure setting located under the shutter speed setting and then specify an exposure value (Exposure), if you want.
A A (Aperture AE) mode
In this mode, you select the aperture and other settings are adjusted accordingly.
Press [SET] to open the Control Panel.
Use [8] and [2] to select (Aperture), and then press [SET].
Use [8] and [2] to change the aperture setting, and then press [SET].
• You also can select the Exposure setting located under the aperture setting and then specify an exposure value (Exposure), if you want.
IMPORTANT!
• The flash > (Auto Flash) and ¥ (Red Eye Reduction) flash modes are not
supported while A, S, or M is selected for the recording mode. If you want the flash to fire, select < (Flash On) as the flash mode.
• The displayed ISO sensitivity, shutter speed or aperture value will turn red when you half-press the shutter button if the image is overexposed or underexposed.
• Selecting S or M for the recording mode and using a slow shutter speed will cause the monitor screen to go blank during the period from when the shutter button is pressed until image recording is complete. Camera operations are disabled during this time. Wait until the back lamp goes out and an image appears on the monitor screen again.
43
Snapshot Tutorial
NOTE

Using the Control Panel

1
5
3 4
7 8
2
6
Control Panel
The Control Panel can be used to configure camera settings.
1. In the REC mode, press [SET].
• You can also display the Control Panel by pressing [2].
2. Use [8] and [2] to select the setting item you want to change, and
then press [SET] or [6].
This will select one of the Control Panel icons and display its settings.*
Self-timer (page 46)
White balance (page 47)
Focus (page 49)
ISO sensitivity (page 53)
Make-up (page 54)
Exposure (page 55)
Flash (page 56)
Metering (page 58)
* Items displayed in the Control Panel depend on the recording mode.
3. Use [8] and [2] to change the setting.
4. After the setting is the way you want, press
[SET].
This will apply the setting and return to the REC mode.
• You also can use on-screen menus to configure settings other than those listed above (page 113).
44
Snapshot Tutorial
NOTE

Configuring Camera Settings with the Function Ring

Function ring
[RING]
Control Panel and menu item functions can be assigned to the function ring. After that, camera settings can be easily configured by rotating the function ring. Functions that can be assigned to the function ring depend on the recording mode.
. To assign functions to the function ring
1. In the REC mode, press [RING].
2. Use [8], [2], [4], and [6] to select the
function you want to assign, and then press [SET].
• You can also use the function ring to select functions.
. To use functions assigned to the function ring
1. Rotate the function ring to change the setting.
2. Press the shutter button to shoot.
• Assigning “Step Zoom” to the function ring makes it possible to adjust optical zoom with the function ring (page 60).
• You cannot assign “MF” (Manual Focus) to the function ring while “On” is selected for face detection.
• The function assigned to the function ring is fixed in certain modes. Motion Shutter Mode: The function ring adjusts the Motion Position (page 76).
• Depending on the recording mode, some of the functions cannot be assigned.
45
Snapshot Tutorial

Using the Self-timer (Self-timer)

‚”•
Front lamp
With the Self-timer, pressing the shutter button starts a timer. The shutter is released and the image is shot after a fixed amount of time.
1. In the REC mode, press [SET].
2. Use [8] and [2] to select the (Self-timer) Control Panel option, and
then press [SET].
3. Use [8] and [2] to select the setting you want and then press [SET].
Setting
10 sec 10-second Self-timer
2 sec
×3 (Triple Self­timer)
REC Screen Icon Display
Description
2-second Self-timer
• When shooting under conditions that slow down the shutter speed, you can use this setting to prevent image blur due to camera movement.
Shoots three images: one image 10 seconds after the shutter button is pressed, and the next two images as soon as the camera is ready after shooting the previous image. How long it takes for the camera to get ready to shoot depends on the image size and quality settings, whether or not a memory card is loaded in the camera, and the flash charge condition.
Off None Turns off the Self-timer.
• The front lamp flashes while the Self-timer countdown is in progress.
• You can interrupt an ongoing Self-timer countdown by pressing [SET].
46
Snapshot Tutorial
NOTE
• The Self-timer cannot be used together with the following features. High Speed CS with Prerecord CS, Prerecord (Movie), Slide Panorama, Wide Shot, Triple Shot
• The Triple Self-timer cannot be used together with the following features. Movie, Time Lapse, High Speed CS, some BEST SHOT scenes, Intelligent Bracketing, Interval Shot
• The Motion Shutter Mode (page 74) can be used only while the Control Panel’s self-timer setting is “Off”. For any other self-timer setting, the applicable self-timer operation is performed.

Adjusting White Balance (White Balance)

You can adjust white balance to match the source of light available where you are shooting and avoid the blue cast that results when shooting outdoors when it is cloudy, and the green cast that results when shooting under fluorescent lighting.
1. In the REC mode, press [SET].
2. Use [8] and [2] to select the (White Balance) Control Panel option,
and then press [SET].
3. Use [8] and [2] to select the shooting condition you want and then
press [SET].
• You can also perform this operation using the function ring.
Setting
Auto WB None
REC Screen Icon Display
Description
Configures the camera to adjust white balance automatically.
Daylight For shooting outdoors on a clear day
Overcast
Shade
Day White
Fluor
Daylight
Fluor
For shooting outdoors on an overcast rainy day, in the shade, etc.
For shooting on a clear day in the shade of trees or buildings
For shooting under white or day white fluorescent lighting
For shooting under daylight fluorescent lighting
47
Snapshot Tutorial
Setting
Blank white paper
Tungsten For shooting under light bulb lighting
Manual
WB
• When “‡Auto WB” is selected for the white balance setting, the camera automatically determines the white point of the subject. Certain subject colors and light source conditions can cause problems when the camera tries to determine the white point, which makes proper white balance adjustment impossible. If this happens, select the white balance setting that matches your shooting conditions (Daylight, Overcast, etc.).
REC Screen Icon Display
Description
For configuring the camera manually to suit a particular light source
Select “Manual WB”.
Under the lighting
conditions you plan to use when shooting, point the camera at a blank white piece of paper so it fills the entire monitor screen and then press the shutter button. Press [SET].
The white balance setting is retained even if you turn off the camera.
48
Snapshot Tutorial

Selecting a Focus Mode (Focus)

• Auto Focus is the only focus mode available while Make-up (page 54) or Face Detection (page 123) is enabled. To select another focus mode, first turn off Make­up and Face Detection.
1. In the REC mode, press [SET].
2. Use [8] and [2] to select the (Focus) Control Panel option, and
then press [SET].
3. Use [8] and [2] to select the setting you want and then press [SET].
Settings
Q
AF (Auto Focus)
´
Macro
Á
Super Macro
W
MF (Manual Focus)
REC Screen Icon Display
None
Type of Shot
General recording
Close ups
Close ups
When you want to focus manually
Focus Mode Approximate Focus Range
Snapshot Movies Snapshot Movies
10 cm to 9 (infinity)
Automatic
Manual
Automatic
3
*
(3.9" to 9) (Wide Angle)
5 cm to 50 cm (2" to 19.7") (Fourth step zoom from the Widest Angle setting)
5 cm to 50 cm (2" to 19.7")
10 cm to 9 (infinity) (3.9" to 9) (Wide Angle)
2
*
2
*
2
*
1
*
The focus range is the distance from the lens surface.
*1 *2 The focus range depends on the current optical zoom position. *3 During High Speed Movie recording, focus is fixed at the position where it was
when recording started. To focus an image, half-press the shutter button for Auto
Focus or focus manually before you press [0] (Movie) to start recording.
49
Snapshot Tutorial
Super Macro
NOTE
NOTE
Yellow boundary
Super Macro fixes optical zoom at a position that allows you to shoot from the closest distance to the subject. The result is closer and larger subject images.
• Zoom is fixed while Super Macro is selected, so no zoom operation is performed
when you rotate the zoom controller.
To focus with manual focus
1. On the monitor screen, compose the image so
the subject you want to focus on is within the yellow boundary.
2. Watching the image on the monitor screen use
[4] (nearer) and [6] (further) to adjust focus.
• At this time the image that is within the boundary will enlarge and fill the monitor screen, which aids in focusing. While an image is enlarged, you can use [2] (6X) and [8] (9X) to change its zoom factor.
• When the function ring (page 45) is set to “MF” (Manual Focus), you can use the function ring for focusing.
3. After the focus is the way you want, press [SET].
• An Auto Macro feature detects how far the subject is from the lens and automatically selects either Macro Focus or Auto Focus accordingly.
• Use of the flash together with Macro Focus can cause the light of the flash to become blocked, which may result in unwanted lens shadows in your image.
• In the case of movie recording, Auto Macro operates before you start recording. After recording is started, however, focus is fixed.
• Whenever you perform an optical zoom operation while shooting with Auto Focus, Macro Focus, or Manual Focus, a value will appear on the monitor screen to tell you the focus range, as shown below. Note that the focus range is displayed including the Auto Macro range only when shooting with Auto Focus. Example: oo
* oo is the actual focusing range value.
• Functions assigned to the [4] and [6] keys with the Key Customize “L/R Key” setting (page 117) are disabled while Manual Focus is selected as the focus mode.
* cm - 9
50
Snapshot Tutorial
Shifting the Focus Frame Position during Manual Focus
NOTE
You can use the procedure below to shift the focus frame position while “MF” (Manual Focus) is selected as the focus mode.
1. While in record standby, press [8] or [2].
2. Use [8], [2], [4] and [6] to shift the focus
frame position and then press [SET].
• In the MF (Manual Focus) mode, you can use [8] or [2] to move the focus frame position and [4] or [6] to adjust focus. Functions assigned to [8], [2], [4], and [6] by the Key Customize “U/D Key” and “L/R Key” settings (page 117) are not used.
• While the focus mode is MF, [8] (DISP) and [2] ( ) perform the functions described above, and do not perform their normal functions (monitor screen content selection and flash setting selection).
• With some Art Shot scenes and some Time Lapse scenes, the focus frame position is fixed in the center and cannot be shifted.
51
Snapshot Tutorial
Using Focus Lock
NOTE
Subject to be focused on
Focus frame
“Focus lock” is a technique you can use when you want to compose an image in which the subject you want to focus on is not within the focus frame in the center of the screen.
• To use focus lock, select “U Spot” or “O Tracking” for the Auto Focus area (page 121).
1. Align the monitor screen’s focus frame with
the subject you want to focus on and then half­press the shutter button.
2. Keeping the shutter button half-pressed
(which maintains the focus setting), move the camera to compose the image.
• When “O Tracking” is selected as the Auto Focus
area, the focus frame will move automatically and follow the subject.
3. When you are ready to shoot the image, press the shutter button the
rest of the way down.
• Focus lock also locks exposure (AE).
52
Snapshot Tutorial
NOTE

Specifying ISO Sensitivity (ISO)

ISO sensitivity is a measure of sensitivity to light.
1. In the REC mode, press [SET].
2. Use [8] and [2] to select the (ISO) Control Panel option, and then
press [SET].
3. Use [8] and [2] to select the setting you want and then press [SET].
Setting
Auto None
ISO80 Lower
ISO100
ISO200
ISO400
ISO800
ISO1600
ISO3200
ISO6400
ISO12800
REC Screen Icon Display
Description
Adjusts sensitivity automatically according to conditions.
sensitivity
Higher
sensitivity
Slow shutter speed
Fast shutter speed
(Set for shooting in
dimly lit areas.)
Less noise
Some coarseness
(increased digital
noise)
• Correction for subject movement (page 125) is performed only while “Auto” is selected for this setting.
• Since higher ISO sensitivity values tend to result in digital noise in images, the camera performs a noise filtering process. Because of this, it may take relatively longer for the camera to finish recording an image after it is shot. You will not be able to perform any key operation while image recording is in progress.
• In the M (Manual Exposure) mode, “Auto” cannot be selected.
• ISO 6400 and ISO 12800 settings cannot be selected while “HDR” or “HDR Art” scene is selected.
53
Snapshot Tutorial
NOTE

Recording Beautiful Portraits (Make-up)

Make-up enables adjustment of human skin tone hues and texture, and softening of facial shadows caused by harsh sunlight for better looking portraits. Make-up can be used with the recording modes listed below.
• Program Auto
• Premium Auto Pro
• Some BEST SHOT scenes
1. In the REC Mode, press [SET].
2. Use [8] and [2] to select the (Make-up Settings) Control Panel
option, and then press [SET].
3. Use [8] and [2] to select “Skin Tone” or “Smooth Skin”, and then use
[4] and [6] to change the setting value.
Skin Tone “Tan +6” to “0 (Off)” to “Light +6”
Smooth Skin “0 (Off)” to “+12 (Max.)”
4. Press [SET].
5. Shoot the image.
• The settings below become configured automatically whenever the “Skin Tone” or “Smooth Skin” level setting is something other than “0 (Off)”. – Face Detection: On – Focus Mode: AF (Auto Focus)
• Make-up cannot be used while shooting with the following feature. Some BEST SHOT scenes, Art Shot, Multi SR Zoom, Time Lapse, Interval Shot, Intelligent Bracketing, RAW+JPEG (Image Size)
54
Snapshot Tutorial
NOTE

Correcting Image Brightness (Exposure)

You can manually adjust an image’s exposure value (EV value) before shooting it.
• Exposure Compensation Range: –2.0 EV to +2.0 EV
• Unit: 1/3EV
1. In the REC mode, press [SET].
2. Use [8] and [2] to select the (Exposure) Control Panel option, and
then press [SET].
3. Use [8] and [2] to adjust the exposure compensation value.
• You can also perform this operation using the function ring.
[8], clockwise: Increases the EV value. A higher EV value is best for light-colored subjects and backlit subjects.
[2], counterclockwise: Decreases the EV value. A lower EV value is best for dark-color subjects and for shooting outdoors on a clear day.
To cancel exposure compensation, change the EV value to “0.0”.
Exposure compensation value
4. Press [SET].
This applies the exposure compensation value. The exposure compensation value you set remains in effect until you change it or turn off the camera (which causes it to revert to “0.0”).
• When shooting under very dark or very bright conditions, you may not be able to obtain satisfactory results even after performing exposure compensation.
55
Snapshot Tutorial

Using Flash (Flash)

[2] ( )
Flash
When flash is required, the flash unit will pop up automatically when you half-press the shutter button.
1. In the REC mode, press [2] ( )
once.
2. Use [8] and [2] to select the
flash setting you want and then press [SET].
Setting
Auto Flash None
Flash Off Flash does not fire.
Flash On
Red Eye
Reduction
REC Screen Icon Display
Description
Flash fires automatically in accordance with exposure (amount of light and brightness) conditions.
Flash always fires. This setting can be used to brighten a subject that normally comes out dark due to daylight or backlight (daylight synchro flash).
Flash fires automatically. This type of flash can be used to reduce the chance of redness in the subject’s eyes.
3. Half-press the shutter button.
The flash unit will pop up automatically when flash is required.
56
Snapshot Tutorial
4. Press the shutter button to shoot all the way down.
NOTE
Back lamp
Flashes amber while the flash is charging to indicate that image recording is disabled.
• You will not be able to take another flash snapshot until the lamp stops flashing amber, which indicates that charging is complete.
< indicates the flash will fire.
• For information about Flash Range, see page 233.
IMPORTANT!
• When not using flash, press down on the flash unit until it locks into place with a click.
• The flash unit pops up automatically, so make sure your hand is not pressing down on it. Also, take care there is no pressure applied to flash unit while it is popped up.
• Foreign matter on the flash window can react with the light of the flash, producing some smoke and abnormal odor. Though this does not indicate malfunction, oil from your fingers and other foreign matter when left on the flash window can become difficult to clean off later. Because of this, you should make it a regular habit to wipe the window clean regularly with a soft, dry cloth.
• Take care so your fingers and the strap do not block the flash.
• The desired effect may not be obtained when the subject is too far away or too close.
• Flash charging time (page 233) depends on operating conditions (battery condition, ambient temperature, etc.).
• Shooting with flash turned off when lighting is dim results in a slow shutter speed, which can cause image blur due to camera movement. Under such conditions, secure the camera with a tripod, etc.
• With red eye reduction, the flash is fired automatically in accordance with exposure. It does not fire in areas where lighting is bright.
• The presence of outdoor sunlight, fluorescent lighting, or some other light source can cause abnormal image colors.
• Select ? (Flash Off) for the flash setting when shooting in areas where flash photography is prohibited.
• The flash > (Auto Flash) and ¥ (Red Eye Reduction) flash modes are not supported while A, S, or M is selected for the recording mode. If you want the flash to fire, select < (Flash On) as the flash mode.
57
Snapshot Tutorial
Red-eye Reduction
Using the flash to shoot at night or in a dimly lit room can cause red spots inside the eyes of people who are in the image. This is caused when the light from the flash reflects off of the retina of the eye. When red-eye reduction is selected as the flash mode, the camera fires a pre-flash to cause the irises in the eyes of any people in the image to close, which reduces the chance of red eye. Note the following important points when using red-eye reduction.
• Red-eye reduction does not work unless the people in the image are looking directly at the camera (flash).
• Red-eye reduction may not work very well if the subjects are located far away from the camera.

Specifying the Metering Mode (Metering)

The metering mode determines what part of the subject is metered for exposure.
1. In the REC mode, press [SET].
2. Use [8] and [2] to select the (Metering) Control Panel option, and
then press [SET].
3. Use [8] and [2] to select the setting you want and then press [SET].
Setting
Multi None
Center
Weighted
Spot
REC Screen Icon Display
Description
Multi-pattern metering divides the image into sections and measures the light in each section for a balanced exposure reading. This type of metering provides error-free exposure settings for a wide range of shooting conditions.
Center weighted metering concentrates on the center of the focus area to measure light. This type of metering is best when you want some level of control over contrast.
Spot metering takes readings at a very small area. Use this metering method when you want exposure to be set according to the brightness of a particular subject, without being affected by surrounding conditions.
58
Snapshot Tutorial

Shooting with Zoom

w Wide Angle z Telephoto
Zoom controller
Your camera is equipped with various types of zoom: optical zoom, HD Zoom, Single SR Zoom, Multi SR Zoom, and digital zoom. The maximum zoom factor depends on the image size setting and the digital zoom on/off settings.
Optical zoom
HD Zoom
Single SR Zoom
Multi SR Zoom
Digital zoom
Zooming is performed by changing the lens focal distance, so there is no deterioration of image quality.
Allows greater zoom capabilities by cutting out a portion of the original image and enlarging it, without deterioration of image quality.
Applies super resolution technology to suppress image deterioration (page 63).
Shoots a burst of high-speed images, which are then combined into a final image in a way that lessens deterioration of image quality. Multi SR Zoom is enabled only when the “Multi SR Zoom” BEST SHOT scene is selected (page 64).
A digital process is used to enlarge the center of the image, so there is deterioration of image quality.
1. In the REC mode, rotate the zoom controller to zoom.
w (Wide Angle): Reduces the size of the subject and broadens the range. z (Telephoto) : Enlarges the subject and narrows the range.
2. Press the shutter button to shoot.
59
Snapshot Tutorial
NOTE
• Use of a tripod is recommended to protect against image blur due to camera
Current focal distance
movement when shooting with telephoto.
• Zoom operations are supported during movie recording. Zoom operations are disabled during high speed movie recording. To use zoom, perform the zoom operation before you press [0] (Movie) to start recording.
• Zoom operations are not supported while shooting with the following feature. The zoom setting is fixed at full wide angle. Slide Panorama, Wide Shot
• Optical zoom is fixed while shooting with the following feature. However, use of digital zoom is supported. All-In-Focus Macro (Optical zoom fixed at full wide angle.) Magnifying Glass (Optical zoom fixed at the closest macro position.)
• Only optical zoom is enabled while shooting with the “RAW+JPEG” image size.
. Zooming with the Function Ring (Step Zoom)
Assigning the Step Zoom function to the function ring lets you perform zoom operations (within the optical zoom range only) with the function ring (page 45). Step Zoom can be adjusted to the focal distances shown below. 28, 35, 50, 75, 100, 135, 200, 300 (Unit: mm; 35 mm film equivalents) For finer zoom adjustment, use the zoom controller.
• The focal distance will be indicated on the monitor screen while Step Zoom is being adjusted with the function ring.
60
Snapshot Tutorial

Monitor Screen Information when Zooming

Focusing Range (Displayed for Auto Focus, Macro Focus, and Manual Focus.)
Focal distance (Converted to 35 mm film format.)
Image quality limit (Deterioration starts from here.)
Zoom bar
Zoom mode
A variety of information is shown on the monitor screen while a zoom operation is in progress.
. Zoom Mode Icons
The table below shows what appears on the monitor screen based on the zoom mode.
Zoom mode REC Screen Icon Display
Optical zoom None
HD Zoom None
Single SR Zoom ¨ (White)
Multi SR Zoom ¸ (Black)
Digital zoom ê
61
Snapshot Tutorial
. Interpreting the Zoom Bar
Range where image deterioration is
suppressed.
Wide Angle Telephoto
Zoom pointer (Indicates current zoom.)
Point from which image deteriorates
• The location of this point depends on the image size, the “Zoom (SR)” setting, and whether Multi SR Zoom is enabled.
Optical zoom limit point
Deteriorated image range
During a zoom operation, a zoom bar appears on the monitor screen to show the current zoom setting.
. Zoom Factor
The digital zoom factor depends on the image size (page 126), the super resolution zoom setting, and on whether or not “Multi SR Zoom” is selected (page 64).
• Multi SR Zoom is enabled only when the “Multi SR Zoom” BEST SHOT scene is selected.
• Only optical zoom is enabled while shooting with the “RAW+JPEG” image size.
Maximum zoom factor where image
Image size
RAW+
JPEG
Optical
zoom
10.7X
deterioration can be suppressed
Zoom (SR): Off
(HD Zoom)
Multi SR Zoom
Zoom (SR): Single
12M 10.7X 10.7X 21.4X 42.8X
3:2 10.7X 10.7X 21.4X 42.8X
16:9 10.7X 10.7X 21.4X 42.8X
8M 10.7X 13.2X 26.2X 52.4X
3M 10.7X 20.9X 41.7X 83.5X
Total maximum
zoom factor
(In combination
with digital zoom)
62
Snapshot Tutorial
NOTE

Zooming with Super Resolution (Zoom (SR))

There are two types of Super Resolution Zoom: Single SR Zoom and Multi SR Zoom. Single SR Zoom uses super resolution to expand the zoom range in which image quality deterioration is minimized. Multi SR Zoom shoots a series of High Speed CS images, which are then combined into an image that enables shooting at higher zoom ratios without loss of image quality. For information about the effective zoom factor ranges in which Super Resolution Zoom is effective, see page 62. The procedure below shows how to configure Single SR Zoom settings. For information about Multi SR Zoom, see page 64.
1. In the REC mode, press [MENU].
2. Press [4], use [8] and [2] to select the “
press [6].
r
REC MENU” tab, and then
3. Use [8] and [2] to select “Zoom (SR)” and then press [SET].
4. Use [8] and [2] to select “Single” and then press [SET].
• Single SR Zoom is effective when you want to capture delicate textures.
• Single SR Zoom does not work during movie recording.
• Single SR Zoom is disabled when shooting with the following functions. Triple Self-timer, Art Shot, Multi SR Zoom, Time Lapse, Interval Shot, High Speed CS, AF CS, Intelligent Bracketing, some BEST SHOT scenes
63
Snapshot Tutorial
NOTE

Expanding the Zoom Range to Shoot Clearer Snapshots (Multi SR Zoom)

This feature uses super resolution technology and multiple Continuous Shutter (CS) images to expand the zoom range for overall images of higher quality and clarity.
1. In the BEST SHOT Mode, select “Multi SR Zoom” (page 93).
2. Press the shutter button to shoot.
• Multi SR Zoom is effective when you want to capture delicate textures.
• The following functions are disabled when shooting with Multi SR Zoom. Single SR Zoom, Triple Self-timer, Sharpness, Contrast, Remote Capture, High Speed CS, AF CS, Motion Shutter, Make-up
• With Multi SR Zoom, the flash setting automatically becomes ? (Flash Off).
• Shooting with this function automatically sets Anti-shake Functions to “Standard” (page 125), but large movement of the camera or subject make it impossible to achieve the desired shot.
• Depending on shooting conditions and image composition, Multi SR Zoom may not be able to produce the desired result.
• When shooting with this feature, “ISO 12800” cannot be selected for “ISO” (page
53).

Shooting with Bracketing (Intelligent Bracketing)

Use the procedure below to shoot a series of images, slightly changing the camera setup with each shot. You can allow the camera to change its setup automatically, and then select any one of the images.
1. Align the mode dial with [M] (Intelligent Bracketing).
2. Press [SET].
3. Use [8] and [2] to select “ ” and then press [SET].
4. Select the bracketing scene you want to use and then press [SET].
• Bracketing scenes 1 through 4 use fixed shooting setups. Advance to step 8.
• Bracketing scenes 5 through 20 use adjustable shooting setups. Advance to step 5.
5. Press [SET], use [8] and [2] to select the (Bracketing Settings)
Control Panel option, and then press [SET].
64
Snapshot Tutorial
6. Adjust the shooting setup as you like.
NOTE
Horizontal axis
Vertical axis
Settings
[4] and [6] keys, or function ring
[8] and [2] keys, or control dial
• With scenes 5 through 13, you can adjust the horizontal axis setting only. With scenes 14 through 20, you can adjust the horizontal and vertical axes bracket settings.
• To cancel settings and return to record standby, press [MENU].
Adjusts the horizontal axis bracket setting.
Adjusts the vertical axis bracket setting.
7. To apply your settings and exit shooting setup
adjustment, press [SET].
The settings you configured appear on the left side of the monitor screen.
8. Press the shutter button to shoot.
• The following functions cannot be used with this function. Zoom (SR), Make-up, Flash, Triple Self-timer, Motion Shutter, Remote Capture, High Speed CS, AF CS, movie recording
• When shooting with this function, the snapshot image quality automatically changes to “Normal”.

Shooting Multiple Images Over a Specified Period (Interval Shot)

You can use the procedure below to record a series of images over a specified period (Interval Shot). This function is useful when recording the movement of stars, a blooming flower, etc.
• When using this function, shooting with a tripod is recommended.
• To prevent loss of power while shooting, use a fully charged battery.
• Make sure the memory card you are using has sufficient unused space before using this function.
• Focus is fixed at what they are when shooting is started.
• Depending on the Interval Shot mode scene you are using, brightness and white balance settings may be fixed at what they are when shooting starts.
1. Align the mode dial with [F] (Time Lapse).
2. Press [SET].
65
Snapshot Tutorial
3. Use [8] and [2] to select the (Time Lapse) Control Panel option
Scene
Interval
Number of shots
Remaining
shooting time
and then press [SET].
4. Select the scene you want to use and then press [SET].
• Select “Interval Shot” or “Interval : Starry sky”.
5. Press [SET], select (Time Lapse Settings), and then press [SET].
6. Use [8] and [2] to select the setting you want to configure, press [6],
and then use [8] and [2] to change the setting.
Interval Specifies the shooting interval.
Shots Specifies the number of shots.
7. Press [SET].
• The current Interval Shot settings are shown at the bottom of the monitor screen.
8. Press the shutter button to start recording.
• The specified number of images is recorded at the interval you specify in step 6. To interrupt an ongoing time lapse operation, press the shutter button.
• Selecting the “Interval : Starry sky” scene causes the focus mode to become “MF” (Manual Focus) (page 49). It is recommended that you point the camera at a bright star and adjust focus as required (page 50).
66
Snapshot Tutorial
NOTE
• The monitor screen is blank while a time lapse operation is in progress. The camera’s back lamp will be lit to indicate that recording is in progress. Performing a camera operation while the monitor screen is blank will cause screen contents to appear. Note, however, that changing the mode dial setting will cause the Interval Shot operation to stop.
• If the “ Interval” setting is one minute or greater, the camera’s lens will retract and the back lamp will go out between shots. Pressing [ON/OFF] (Power) while an Interval Shot operation is in progress will cause a message to appear. The camera’s battery can be charged over a USB connection while the lens is retracted during Interval Shot. If you want the battery to be charged during Interval Shot, set up the USB connection before starting the recording operation. Connecting the USB cable while the lens is extended will cause camera power to turn off.
• The “Auto Flash” and “Red Eye Reduction” flash settings are not supported while a setting other than “Auto” is selected for the “Aperture” or “Shutter Speed” setting while using Interval Shot. Selecting Interval Shot while an unsupported flash setting is in effect will cause the flash mode setting to change automatically to “Flash Off”.
• The functions below cannot be used with this function. Remote Capture, CS, Motion Shutter, Anti-shake Functions, Zoom (SR), Continuous AF, EX Finder, Type 4 Review setting, Digital Zoom
• Pressing the shutter button while the camera is standing by between Interval Shot shots will cancel the Interval Shot operation and display the message “Interval recording was canceled.”
• The Auto Power Off is disabled while shooting with this function (page 195).
67
Snapshot Tutorial

Shooting a Burst of Images (CS)

Maximum CS shots
CS speed

Shooting with High Speed CS

With High Speed CS, recording continues as long as you keep the shutter button depressed. The table below shows the settings that can be specified for the CS speed and the number of images per High Speed CS operation.
CS Speed (High Speed CS fps)
Maximum CS Shots
3 fps, 5 fps, 10 fps, 15 fps, 30 fps fps = frames per second
5, 10, 20, 30
1. Align the mode dial with [P] (Program Auto).
2. Press [MENU].
3. Press [4], use [8] and [2] to select the “
press [6].
r
REC MENU” tab, and then
4. Use [8] and [2] to select “CS”, and then press [SET].
5. Use [8] and [2] to select “High Speed CS” and then press [SET].
This will cause the recording mode icon on the screen to become Ú.
6. Press [SET].
7. Use [8] and [2] to select the (High Speed CS fps) Control Panel
option and then press [SET].
8. Use [8] and [2] to select the continuous shutter (CS) speed you want
and then press [4].
• Use a higher “High Speed CS fps” setting when shooting a fast-moving subject.
68
Snapshot Tutorial
9. Use [8] and [2] to select the (Maximum CS Shots) Control Panel
option and then press [SET].
10.
Use [8] and [2] to select the maximum number of shots and then press [SET].
11.
Press the shutter button the rest of the way and hold it down.
Shooting of images will continue as long as you depress the shutter button or until the maximum number of images specified by “High Speed CS fps” is reached.

Using High Speed CS (60 fps)

High Speed CS lets you shoot a burst of up to 60 images at a speed of up to 60 frames per second (fps). Images shot with this function are 8M in size, and have an aspect ratio to 16:9. Aperture and shutter speed settings can be configured manually.
1. In the BEST SHOT Mode, select “60 fps High Speed CS” (page 93).
2. Press [SET].
3. Use [8] and [2] to select the (High Speed CS fps) Control Panel
option and then press [SET].
4. Use [8] and [2] to select the continuous shutter (CS) speed you want
and then press [4].
5. Use [8] and [2] to select the (Maximum CS Shots) Control Panel
option and then press [SET].
6. Use [8] and [2] to select the maximum number of shots and then
press [6].
7. Use [8] and [2] to select the (Pre-record CS Shots) Control Panel
option and then press [SET].
8. Use [8] and [2] to select the number of Prerecord (Still) images and
then press [SET].
If you select “0 shots”, no pre-record images will be stored when you half-press the shutter button.
9. Half-press the shutter button.
A pre-record buffer is continually updated with images as long as the shutter button is pressed.
• The camera will not emit shutter sounds as it pre-records images.
• Releasing the half-pressed shutter button will cause the contents of the pre­record buffer to be deleted.
69
Snapshot Tutorial
10.
NOTE
Press the shutter button the rest of the way and hold it down.
Full pressing the shutter button will record the images in the pre-record buffer followed by real-time recorded images. Shooting of images will continue as long as you depress the shutter or until the maximum number of images specified by “Maximum CS Shots” is reached.
• After shooting, you will not be able to shoot again until the camera finishes processing of the images.
• The settings below can be configured while shooting with this function. Shutter Speed: Auto, 1/60 to 1/20000 seconds ISO Sensitivity: Auto, ISO80 to ISO12800 (The actual available setting range depends on the shutter speed and aperture.) High Speed CS fps: 15 to 60 Maximum CS Shots: 10 to 60 Pre-record CS Shots: 0 to 55
• Images shot with this function are 16:9 (3840
x
2160) in size. Snapshot image
quality is “Normal”.
• The functions below cannot be used with this function. Single SR Zoom, Make-up, Remote Capture, EX Finder, Review, Front Shutter “AF less” and “CS”, Motion Shutter, movie recording, Flash, Timestamp
• You cannot use Triple Self-timer with this function. However, when the “Pre-record CS Shots” setting is something other than 0, Self-timer also cannot be used.
• The current High Speed CS fps, Maximum CS Shots, and Pre-record CS Shots settings are retained when the camera is turned off.
• Selecting a different BEST SHOT scene or turning off the camera causes the following settings to be reset to their initial defaults: ISO sensitivity, aperture, shutter speed.
• The CS Multi Print PLAY mode function cannot be used with group files recorded with this function.
• Custom Shot setup registration is not supported for images shot with this function.
70
Snapshot Tutorial

Shooting with Prerecord CS

Shutter button half-press
Recorded images (up to 30 images)
Pre-recorded images
Shutter button full-press
Shutter button
release
Continuous recording of images until shutter
button released
Half-pressing and holding the shutter button causes a pre-record buffer to be continually updated with images. When the shutter button is fully pressed, buffer contents are recorded along with a series of real-time images. Use Prerecord CS when you want to make sure you do not miss fast-moving action.
1. Align the mode dial with [P] (Program Auto).
2. Press [MENU].
3. Press [4], use [8] and [2] to select the “
press [6].
r
REC MENU” tab, and then
4. Use [8] and [2] to select “CS”, and then press [SET].
5. Use [8] and [2] to select “High Speed CS” and then press [SET].
This will cause the recording mode icon on the screen to become Ú.
6. Press [SET].
7. Use [8] and [2] to select the (High Speed CS fps) Control Panel
option and then press [SET].
8. Use [8] and [2] to select the continuous shutter (CS) speed you want
and then press [4].
• Use a higher “High Speed CS fps” setting when shooting a fast-moving subject.
9. Use [8] and [2] to select the (Maximum CS Shots) Control Panel
option and then press [SET].
10.
Use [8] and [2] to select the maximum number of shots and then press [4].
71
Snapshot Tutorial
11.
NOTE
Use [8] and [2] to select the (Pre-record CS Shots) Control Panel option and then press [SET].
12.
Use [8] and [2] to select the number of Prerecord (Still) images and then press [SET].
• Settings: 0 shots, 3 shots, 5 shots, 10 shots, 15 shots, 20 shots, 25 shots
• If you select “0 shots”, no pre-record images will be stored when you half-press the shutter button.
13.
Half-press and hold the shutter button to start pre-recording.
A pre-record buffer is continually updated with images as long as the shutter button is pressed.
• The camera will not emit shutter sounds as it pre-records images.
• Releasing the half-pressed shutter button will cause the contents of the pre­record buffer to be deleted.
14.
Full press and hold down the shutter button.
This will record the images in the pre-record buffer followed by real-time recorded images. Shooting of images will continue as long as you depress the shutter or until the maximum number of images specified by “High Speed CS fps” is reached.
• You can use any one of the following recording modes to shoot with High Speed CS: A (Aperture AE) mode, S (Shutter Speed AE) mode, M (Manual Exposure) mode.
• The greater the number of shots, the longer it takes to save them after shooting is complete.
• When using a continuous shutter mode, keep the camera still until shooting is finished.
• Zoom is disabled during continuous shutter operations.
• When shooting with this function, the snapshot image quality automatically changes to “Normal”.
• When shooting with this function, exposure and focus for the first image are applied for successive images as well.
• When shooting with this function, the flash setting automatically becomes ? (Flash Off).
• The following image sizes cannot be selected while shooting with this function: RAW+JPEG, 3:2, 16:9. Entering the High Speed CS mode while any one of these image sizes is selected will cause the image size setting to change to “12M” automatically.
• The following functions cannot be used when shooting with this function. Motion Shutter, Triple Self-timer, Zoom (SR)
• During CS recording some setting items are dimmed on the display and cannot be selected.
• The Self-timer cannot be used in the Prerecord CS mode.
72
Snapshot Tutorial
• If you assign “CS” to the Key Customize (page 117) “U/D Key” setting, you can
NOTE
change the CS mode by pressing the [8] or [2] key. If you assign “CS” to the “L/R Key” setting, you can change the CS mode by pressing the [4] or [6] key.

Using Continuous Shutter with Auto Focus (AF CS)

AF CS shoots up to 30 CS images while keeping the subject in focus. This feature comes in handy when shooting children and other fast-moving subjects. The CS speed is automatically adjusted in accordance with shooting conditions within the range of three to six frames per second.
1. Align the mode dial with [P] (Program Auto).
2. Press [MENU].
3. Press [4], use [8] and [2] to select the “
press [6].
r
REC MENU” tab, and then
4. Use [8] and [2] to select “CS”, and then press [SET].
5. Use [8] and [2] to select “AF CS” and then press [SET].
This will cause the recording mode icon on the screen to become Ù.
6. Press the shutter button the rest of the way down.
Hold down the shutter button to shoot up to 30 images at high speed.
• You can use any one of the following recording modes to shoot with AF CS: A (Aperture AE) mode, S (Shutter Speed AE) mode, M (Manual Exposure) mode.
• Zoom is disabled during continuous shutter operations.
• The following image sizes cannot be selected while shooting with Auto Focus CS: RAW+JPEG, 3:2, 16:9. If select AF CS while either of these image sizes is selected, the camera will automatically switch the images size setting to 12M.
• The following camera features cannot be used while shooting with Auto Focus CS: Motion Shutter, Triple Self-timer, Single SR Zoom.
• The settings in the table below are fixed while shooting with AF CS.
Image Quality Normal
Flash Flash Off
Focus Mode AF
AF Area Spot
73
Snapshot Tutorial
NOTE

Triggering a Self-timer Operation with Motion (Motion Shutter)

With this feature, the camera automatically triggers a self-timer countdown whenever it detects movement in the vicinity of an icon on the monitor screen. This means you can control operation of the self-timer from a distance by waving your hand, so you can include yourself in the image being shot.
1. Select one of the following as the recording
mode: Program Auto, Premium Auto Pro, or HS Best Selection or Make-up (BEST SHOT scene).
• Movie shooting is disabled while the HS Best Selection BEST SHOT scene is being used.
2. Tilt the camera’s monitor screen upwards 180 degrees (page 19).
• Under initial factory default settings, the camera will automatically enter the Motion Shutter Mode whenever the monitor screen is tilted upwards 180 degrees.
3. Rotate the function ring to reposition the self-timer start icon “ ” to
the location in the image where you want movement to be detected.
• If you also want to reposition the preview icon “ ”, press [RING] and then rotate the function ring.
4. After the icons are in the positions you want, press [SET].
5. Press the shutter button (if you want to shoot a snapshot) or
[0] (Movie) (if you want to shoot a movie).
The start self-timer icon will change to “ ” to indicate that the camera is in standby for shooting.
6. Facing the camera, move your hand or perform some other movement
in the vicinity of the (start self-timer) icon on the monitor screen.
When the camera detects movement near the icon, it will automatically shoot an image.
• To stop movie recording, press [0] (Movie) again.
• In the case of snapshot shooting, the camera will return to standby after an image is shot. The camera will automatically exit standby after 30 snapshots are shot using the Motion Shutter.
• Any one of the following will automatically exit standby: pressing the shutter button, changing the tilt orientation of the monitor screen, or turning the camera upside down.
74
Snapshot Tutorial
• The Motion Shutter may not operate properly when there is little difference between the subject and the background of the icon, or when the subject is located far away from the camera.
(preview icon) will appear on the monitor screen when a snapshot is shot. When the camera detects movement in the vicinity of the preview icon, it will display the image that was shot for three seconds.
•“O Tracking” cannot be selected for the AF area setting while shooting with the Motion Shutter. If “O Tracking” is selected in another mode, selecting the Motion Shutter will cause the AF area setting to change to “U Spot”.
• You cannot shoot a snapshot by pressing the shutter button while movie recording is in progress (Snapshot In Movie).
75
Snapshot Tutorial

Configuring Motion Shutter Settings (Motion Shutter)

Use the procedure below to configure Motion Shutter settings.
1. In the REC mode, press [MENU].
2. Press [4], use [8] and [2] to select the “
r
REC MENU” tab, and then
press [6].
3. Use [8] and [2] to select “Motion Shutter” and then press [6].
4. Configure Motion Shutter settings.
Setting Description
Specifies the Motion Shutter activation operation. Always:
Motion Settings
Timer
Motion Position
Motion Shutter remains activated, regardless of whether or not the monitor screen is tilted.
180°only:
Motion Shutter is activated when the monitor screen is tilted 180 degrees.
Off: Motion Shutter disabled.
Specifies the amount of time that should elapse until shooting starts after the camera detects movement. Settings: 0.5 sec, 1 sec, 2 sec, 10 sec
Changes the positions of the self-timer icon “ ” and preview icon “ ”. [8] [2] [4] [6]: Moves the currently selected icon. [RING]: Selects the icon to be moved.
76
Snapshot Tutorial

Shooting with Artistic Effects (Art Shot)

A variety of artistic effects help to make even common, ordinary subjects become more novel and exciting.
Scene Description
Applies HDR (High Dynamic Range, page 103) photography
HDR Art
Toy Camera
Soft Focus Blurs overall focus for a mysteriously soft effect.
Light Tone Weakens contrast to create an elegantly subdued effect.
Pop Strengthens saturation for richer colors.
Sepia Sepia colors are used to create a retro effect.
Monochrome Enhances contrast to create a grainy print effect.
Miniature
Fisheye
Sparkling Shot
Crystal Ball
to transform snapshots and movies into works of art that provide a greater degree of expression than conventional imaging.
Darkens the periphery and changes hues for a toy camera effect.
Blurs some of the focus to make the image look like a miniature.
Humorous effect that looks like it was shot with a fisheye lens.
Softens the overall image and adds points of light for a sparkle effect.
Creates a mysterious effect by placing the image in a bubble floating in midair.
1. Align the mode dial with [C] (Art Shot).
2. Press [SET].
3. Use [8] and [2] to select , and then press [SET].
4. Select the Art Shot scene you want to use and then press [SET].
77
Snapshot Tutorial
5. Press [SET], use [8] and [2] to select the fifth Control Panel option
from the top, and then press [SET].
The intensity of the selected effect can be adjusted as described below.
Scene Adjustment
HDR Art Effect level
Toy Camera Hue
Soft Focus Effect level
Light Tone Hue
Pop Effect level
Sepia Effect level
Monochrome Effect level
Miniature Focus area
Fisheye Effect level
Sparkling Shot Effect type
Crystal Ball Effect type
6. Use [8] and [2] to change the setting.
7. Press [SET].
8. Press the shutter button to shoot.
. Using the Scene Information Screen
To find out more about a scene, select it with the boundary on the scene menu and then rotate the zoom controller in either direction.
• To return to the scene menu, rotate the zoom controller again.
• To scroll between scenes, use [4] and [6].
• To configure the camera with the settings for the currently selected scene, press [SET].
78
Snapshot Tutorial
NOTE
• Depending on the “Art Shot” scenes, some of the items on the menu that appears
NOTE
may not be usable.
• With this “Art Shot” scene, the flash setting automatically becomes ?(Flash Off).
• Movie recording is disabled while “Sparkling Shot” is selected.
• The “Movie Quality” setting can be either “HD” or “STD” only (page 128). When any “Movie Quality” setting other than “STD” is selected in another mode, the “HD” setting is used when shooting with Art Shot.
• When using “HDR Art” for movie recording, the intensity of the art effect is fixed in accordance with movie settings.
• An image shot with an Art Shot scene cannot be converted to a normal image without the Art Shot effect.

Saving a Second Normal Image When Shooting with HDR Art (Double (HDR Art))

You can configure the camera to save two images when shooting with HDR Art: one image with HDR Art effects applied in accordance with the scene you selected plus another normal (Program Auto) image without any effects applied.
1. Align the mode dial with [C] and then press [MENU].
2. Press [4], use [8] and [2] to select the “
press [6].
r
REC MENU” tab, and then
3. Use [8] and [2] to select “Double (HDR Art)” and then press [SET].
4. Use [8] and [2] to select “On” and then press [SET].
While “Off” is selected for the above step, only a single HDR Art image is saved (normal image not saved).
5. Press the shutter button to shoot.
• Except for HDR Art, shooting with an Art Shot scene saves only an Art Shot image. No companion normal (non Art Shot) image is saved.
79
Snapshot Tutorial
NOTE

Creating and Using Your Own Setups (Custom Shot)

You can register up to 12 setups, based on snapshots shot with the camera, as Custom Shot scenes. Selecting a registered Custom Shot scene configures the camera with its settings.
. To register a Custom Shot scene
1. Align the mode dial with [C] (Custom Shot).
2. Press [SET].
• A message will appear if there are no Custom Shot scenes currently registered. If there is one or more images that are supported for Custom Shot scene registration, press [SET] to advance to step 5, below. Otherwise proceed with step 3.
3. Use [8] and [2] to select
(Custom Scene) and then press [SET].
4. Use [8], [2], [4], and [6] to select “Custom Shot” (New Scene), and
then press [SET].
5. Use [8], [2], [4], and [6] to select a snapshot.
6. Use [8] and [2] to select “Save” and then press [SET].
• Custom Shot setup registration is not supported for images shot with the functions below. Custom Shot setup registration is also not supported for movies. Premium Auto Pro, Multi SR Zoom, Snapshot In Movie
• You can register the setup of a single image that is part of a CS group. Note, however, that the resulting Custom Shot scene will be for a snapshot, not a CS Mode operation.
• You can check the settings of the currently selected Custom Shot scene by displaying the camera’s setting menus and looking at its settings.
• Custom Shot scenes are assigned numbers in the sequence: U1, U2, U3, and so on.
• The settings and functions below are not registered as part of a Custom Shot scene. Motion Shutter, Motion Position, Image Size, Image Quality, ISO High Limit, Digital Zoom, MF Position, Self-timer, aperture, Some of the settings when shooting with Intelligent Bracketing
• Custom Shot scenes are stored in built-in memory in the SCENE folder (snapshots) (page 189).
• Formatting the camera’s built-in memory (page 201) deletes all the Custom Shot scene files.
• If the “User Set Up” setting is assigned to the front shutter button, you can register the setup of the currently displayed snapshot as a Custom Shot scene simply by displaying it and then pressing the front shutter button.
80
Snapshot Tutorial
• Use the following steps when you want to delete a Custom Shot scene.
In step 4 of the above procedure, select the scene you want to delete.
• To view a particular image, rotate the zoom controller.
Press [2] ( ), select “Cancel”, and then press [SET].
. To record with a registered Custom Shot scene
1. In the REC Mode, align the mode dial with [C] (Custom Shot).
2. Press [SET].
3. Use [8] and [2] to select
(Custom Scene) and then press [SET].
4. Use [8], [2], [4], and [6] to select the scene you want and then press
[SET].
5. Press the shutter button to shoot.
Scene Screen Operations
To view a particular Custom Shot scene, rotate the zoom controller.
• To return to the scene menu, rotating the zoom controller again.
• To scroll between scenes, use [4] and [6].
• To configure the camera with the settings for the currently selected scene, press [SET].
81
Snapshot Tutorial

Recording Movies

[0] (Movie)
[MENU]
[SET]
[8][2][4][6]
Mode dial
Recording time
Remaining recording time
(page 230)

To record a movie

The following procedure explains how to record a standard (STD) movie. This camera supports Premium Auto Pro movie recording (page 83). See the pages indicated below for more information about movies. High-definition movie (FHD movie): page 85 High speed movie (HS movie): page 85
1. Align the mode dial with [P] (Program
Auto) or [Ÿ] (Premium Auto Pro).
2. Press [MENU].
3. Press [4], use [8] and [2] to select the
“rREC MENU” tab, and then press [6].
4. Use [8] and [2] to select “Movie Quality”
and then press [6].
5. Use [8] and [2] to select “STD”, and then
press [SET].
• Recording is performed with an aspect ratio of 4:3, an image size of 640x480 pixels, and a frame rate of 30 frames per second (STD Movie). Image size setting cannot be changed.
• The shooting range for movies is smaller than that for snapshots. You can display the movie shooting range with “Shooting Info” (page 134).
6. Point the camera at the subject and then
press [0] (Movie).
This will start recording and display Y on the monitor screen. Movie recording includes stereo audio.
• Pressing [SET] will re-start a Continuous AF operation (page 124).
7. Press [0] (Movie) again to stop recording.
• Each movie can be up to 29 minutes long. Movie recording stops automatically after 29 minutes of recording. Movie recording also will stop automatically if memory becomes full before you stop movie recording by pressing [0] (Movie) again.
82
Recording Movies
Recording Movies with Premium Auto Pro
Microphones
When Premium Auto Pro is enabled (page 34), the camera automatically make judgments about the subject, shooting conditions, and other parameters. The result is higher quality images than those produced by Program Auto recording. The shooting environment detected by the camera is displayed at the bottom of the REC mode screen.
• Premium Auto Pro is enabled for FHD movies and STD movies only.
• Using Premium Auto Pro uses up the battery charge more quickly than using Program Auto recording.
Shooting with BEST SHOT
With BEST SHOT (page 93), you can select the sample scene that matches the type of movie you are trying to shoot and the camera will change its setup accordingly, for beautiful movies every time.
Minimizing the Effects of Camera Movement during Movie Recording
You can use Anti-shake Functions (page 125) to configure the camera to minimize the effects of camera movement during FHD and STD movie recording. Note that Anti-shake Functions cannot be used with HDR Art Movie and that Anti-shake Functions does not prevent image blur due to subject movement.

Audio

Your camera has built-in microphones that can be used to record audio (stereo) during movie recording.
• Your camera has a function to reduce wind noise (Wind Noise Cut) when recording movies (page 132).
. Recording Precautions
• The camera also records audio. Note the following points when shooting a movie. – Take care that the microphones are not blocked by your
fingers, etc.
– Good audio recording results are not possible when the
camera is too far away from what you are trying to record.
– Performing a zoom operation while shooting can cause zoom and/or auto focus
noise to be in the audio recording.
– Operating camera buttons while shooting can cause button noise to be picked
up in the audio.
• When shooting with the “HS” movie quality at a frame rate setting of “30-120 fps” or “30-240 fps”, audio is recorded only while the camera is shooting at 30 fps. Audio is not recorded at any other frame rates.
83
Recording Movies
IMPORTANT!
NOTE
• Spending a long time using movie recording will cause the camera to become slightly warm to the touch. This is normal and does not indicate malfunction. The camera may automatically adjust its monitor screen brightness in order to reduce heat generation.
• Shooting movies for long periods in areas where temperature is relatively high can cause digital noise (dots of light) to appear in the movie image. A rise in the camera’s internal temperature also may force movie recording to stop automatically. If this happens, stop recording and allow the camera to cool down, which should cause normal operation to resume.
• Use of the camera’s built-in memory or certain types of memory cards can slow down processing speeds. In particular, high-quality movies may not be able to be stored correctly. A slow memory card can take too much time to record data and result in breaks in the image and/or audio during playback. When this happens a yellow “Y” indicator will appear on the monitor screen.
• Zoom operations are supported during movie recording (page 59). Zoom is disabled during high speed movie recording. To use zoom for high speed movie recording, perform the zoom operation before you press [0] (Movie) to start recording.
• Both Single SR Zoom (page 63) and Multi SR Zoom (page 64) are disabled during movie recording.
• The effects of camera movement in an image become more pronounced when you shoot close up or with a large zoom factor. Because of this, use of a tripod is recommended under these conditions.
• Except for High Speed Movie, Continuous AF (page 124) is performed during movie recording while “AF” (Auto Focus) or “Macro” is selected for the “Focus” setting.
• Face Detection is disabled during normal FHD and STD, and high speed movie recording. Face Detection is enabled when shooting movies with Premium Auto Pro (FHD and STD).
• The following functions do not support movie recording. Some BEST SHOT scenes, some Art Shot scenes, Time Lapse, Intelligent Bracketing
84
Recording Movies

Recording a High-definition Movie

This camera supports recording of high-definition (FHD) movies. The aspect ratio of an FHD movie is 16:9, the image size is 1920 30 fps. Image quality and image size settings cannot be changed.
x
1080 pixels, and the frame rate is
1. Align the mode dial with [P] (Program Auto) or [Ÿ] (Premium Auto
Pro).
2. Press [MENU].
3. Press [4], use [8] and [2] to select the “
press [6].
r
REC MENU” tab, and then
4. Use [8] and [2] to select “Movie Quality” and then press [6].
5. Use [8] and [2] to select “FHD”, and then press [SET].
6. Record the movie the same way as you would a normal movie (page
82).
Press [0] (Movie) to start and stop recording.

Recording a High Speed Movie

This camera supports recording of high speed movies at a maximum speed of 1000 fps. The aspect ratio of movies recorded with this mode depends on the frame rate (recording speed).
• When recording with the frame rate setting of “30-120 fps” or “30-240 fps” frame rate setting, audio recording is supported during 30 fps recording only. Audio is not recorded at any other frame rates.
1. Align the mode dial with [P] (Program Auto).
2. Press [MENU].
3. Press [4], use [8] and [2] to select the “
press [6].
r
REC MENU” tab, and then
85
Recording Movies
4. Use [8] and [2] to select “Movie Quality” and then press [6].
5. Use [8] and [2] to select the frame rate (recording speed) you want
and then press [SET].
A fast frame rate (such as 1000 fps) will result in a smaller image size.
Movie
Quality
HS1000 1000 fps 224
REC Screen Icon Display
Frame Rate
Image Size
(Pixels)
x
64
HS480 480 fps 224x160
x
HS240 240 fps 512
HS120 120 fps 640
HS30-240 30-240 fps 512
HS30-120 30-120 fps 640
384
480
384
480
• fps (frames per second) is a unit of measurement indicating the number of images recorded or played back per second.
x
x
x
6. Record the movie the same way as you would a normal movie (page
82).
Press [0] (Movie) to start and stop recording.
• During High Speed Movie recording (HS120, HS240, HS480, HS1000), focus is fixed at the position where it was when recording started. To focus an image, half-press the shutter button for Auto Focus or focus manually before you press [0] (Movie) to start recording.
• Continuous AF is operational when recording at 30 fps with “HS30-120” or “HS30-240”. However, focus becomes fixed whenever you switch to 120 fps or 240 fps.
• When “HS30-120” or “HS30-240” is selected as the frame rate, recording always starts with a frame rate of 30 fps. You can switch the frame rate between 30 fps and 120 fps or between 30 fps and 240 fps only while recording is in progress. Press [4], [6], or [SET] to switch speeds. Audio is recorded only while shooting at a 30 fps.
86
Recording Movies
NOTE
• The higher the frame rate (speed), the more lighting is required when shooting.
[0] (Movie)[0] (Movie)
Movie
Real-time recording start
Approximately 5-second prerecorded part (from the buffer)
• Approximately two seconds for high speed movie
Real-time recording end
When shooting a high speed movie, shoot in a well-lit environment.
• When recording certain types of movies, the image that appears on the monitor screen may be smaller than normal. When recording a high speed movie, there are black bands along the top, bottom, left, and right of the screen.
• When recording a high speed movie, light source flicker can cause horizontal bands to appear in the image. This does not indicate malfunction of the camera.
• Monitor screen content switching is disabled during high speed movie recording.

Using Prerecord Movie (Prerecord (Movie))

Prerecord (Movie) maintains a pre-recording of approximately five seconds of action (approximately two seconds for High Speed Movie). When you start real-time recording, the pre-recorded content is stored followed by the real-time recording, to help make sure you do not miss anything by being late pressing the record button.
87
Recording Movies
. To set up the camera to shoot with Prerecord Movie
1. Align the mode dial with [b] (BEST SHOT).
2. Press [MENU].
3. Press [4], use [8] and [2] to select the “
press [6].
r
REC MENU” tab, and then
4. Use [8] and [2] to select “Movie Quality” and then press [6].
5. Use [8] and [2] to select the movie quality you want to use for
shooting and then press [SET].
6. Press [SET].
7. Use [8] and [2] to select , and then press [SET].
8. Use [8], [2], [4], and [6] to select the “Prerecord (Movie)” scene and
then press [SET].
This causes (Prerecord (Movie)) to appear on the monitor screen, indicating that the camera is prerecording to its buffer.
. To shoot a Prerecord Movie
1. After using the above procedure to set up the camera for Prerecord
Movie, point the camera at the subject.
2. When you are ready to record, press [0] (Movie).
This will save the approximately five seconds of action that was prerecorded in the buffer before you pressed [0] (Movie) (two seconds if you are using high speed movie) and start real-time recording.
3. Press [0] (Movie) again to stop recording.
• To turn off Prerecord Movie recording, align the mode dial with [P] (Program
Auto) or [Ÿ] (Premium Auto Pro).
• When shooting with the high speed movie “HS30-120” and “HS30-240” setting, you cannot change the speed (fps) setting while the camera is pre-recording to the buffer in step 1 of the above procedure. You can change the speed (fps) setting after you press [0] (Movie) to start real-time recording.
88
Recording Movies
NOTE
• While the camera is set up for shooting with Prerecord Movie, pressing the shutter button will not shoot a snapshot unless movie recording is in progress. With high­definition (FHD) and standard (STD) movie, you can shoot still images while realtime movie recording is in progress.
• When shooting with Prerecord Movie in combination with high speed movie, rotating the control dial will not change the Exposure or white balance setting, even if “Exposure” or “White Balance” is assigned for the “Control Dial” function (page
117). To change the Exposure or white balance setting in this case, use the Control Panel.

Recording a Time Lapse Movie (Time Lapse)

You can use this function to record movies of natural events that occur over time, to speed up the flow of traffic in a city scene, or to record other similar types of movies.
• When using this function, shooting with a tripod is recommended.
• To prevent loss of power while shooting, use a fully charged battery.
• Make sure the memory card you are using has sufficient unused space before shooting with this function.
• Focus is fixed at what they are when shooting is started.
• For some scenes, brightness and white balance settings are fixed at what they are when shooting is started.
1. Align the mode dial with [F] (Time Lapse).
2. Press [SET].
3. Use [8] and [2] to select the (Time Lapse) Control Panel option
and then press [SET].
4. Select the scene you want to use and then press [SET].
• A scene that can be used for time lapse recording is indicated by ».
5. Press [SET], select (Time Lapse Settings), and then press [SET].
6. Use [8] and [2] to select “ Interval” or “ Total Time”, press [6],
and then use [8] and [2] to change the setting.
Each scene is initially configured with unique “ Interval” and “ Total Time” default settings suitable for that scene. You can change these settings, if you want.
Interval Specifies the number of seconds between shots.
Total Time
Specifies the recording time. Selecting “Off” causes recording to continue until the shutter button is pressed again.
89
Recording Movies
7. Press [SET].
NOTE
Interval
Total Time
Scene
Remaining recording time
Recording time
• Time Lapse settings are shown at the bottom of the screen.
8. Press the shutter button to start recording.
• Shooting is repeated at the interval specified in step 6.
• Recording stops when the recording time specified in step 6 elapses or when the shutter button is pressed again.
• Remaining recording time is not displayed when the “ Total Time” setting is “Off”.
• During Time Lapse recording, the monitor screen will turn off in accordance with the “Sleep” setting (page 195). Change the “Sleep” setting to “Off” if you want the monitor screen to stay on. Note, however, that this setting will use up battery power more quickly.
• If sleep is enabled (page 195), the monitor screen will turn off after the preset sleep period if no camera operation is performed, but the time lapse recording operation will continue. The camera’s back lamp will flash at this time. Performing any operation while the monitor screen is blank will turn it back on. However, the following operations will not turn the monitor screen back on. – Pressing [ON/OFF] (Power) – Pressing the shutter button all the way – Rotating the mode dial
• The Auto Power Off is disabled while time lapse recording is in progress (page
195).
• The following functions cannot be used with this function. Single SR Zoom, Anti-shake Functions, Lighting, Continuous AF, Triple Self-timer, Motion Shutter, Face Detection, Metering, ISO, ISO High Limit, Make-up, Review
• The frame rate of playback of movies shot with this function is 20 fps. Movie quality depends on the scene you are using. Scene 3 to 8: FHD Scene 9 to 13: HD
• Note that audio is not recorded when recording with this function.
• The camera can be configured to play only Time Lapse movies during a slideshow (page 152).
• When using “» HDR Art ” for movie recording, the intensity of the art effect is fixed in accordance with movie settings.
• You cannot shoot a snapshot by pressing the shutter button while time lapse recording is in progress (Snapshot In Movie).
90
Recording Movies
• The reset operation (page 201) returns “Interval” and “Total Time” to their initial default settings. Each Time Lapse scene has its own unique “Interval” and “Total Time” settings.
• To adjust brightness when shooting with the Time Lapse “» Night Scene”, use
(Shutter Speed) on the Control Panel (page 44) to adjust the shutter speed.
. Using the Scene Information Screen
To find out more about a scene, select it with the boundary on the scene menu and then rotate the zoom controller in either direction.
• To return to the scene menu, rotate the zoom controller again.
• To scroll between scenes, use [4] and [6].
• To configure the camera with the settings for the currently selected scene, press [SET].
91
Recording Movies
NOTE
Shooting a Snapshot while Shooting a Movie
Number of recordable snapshots
Snapshot recording mode
(Snapshot In Movie)
You can shoot snapshots while movie recording is in progress. When the camera is in the Single Shot mode, you can shoot snapshots one-by-one. In the CS mode, holding down the shutter button will record up to seven consecutive images at a speed of approximately 10 images per second (fps). You can shoot a maximum total of 28 images during a single movie recording operation.
1. While a movie is being recorded, press the
shutter button.
• Select FHD movie or STD movie as the movie quality setting (page 128).
• In the CS mode, images continue to be shot as long as you keep the shutter button depressed.
• While movie recording is in progress, you can toggle between the Single Shot Mode and the CS mode by pressing [4], [6], or [SET]. Note that this method for mode switching is possible only during movie recording. The CS mode is indicated when is white (on the monitor screen), and the Single Shot mode is selected when t is white.
• Note that the flash cannot be used when shooting a Snapshot In Movie.
• Note that shooting a snapshot while shooting a movie is supported during FHD movie and STD movie recording only. It is not supported during other types of movie recording.
• Snapshots shot with Snapshot In Movie cannot be focused individually. The focus will be the same as the movie being recorded.
• The field of view of a snapshot shot while FHD movie recording is in progress will be wider than the field of view of the FHD movie.
• The snapshot image quality automatically changes to “Normal”.
• The P (Program Auto) recording mode is used when you shoot a snapshot during movie recording.
• You cannot shoot with Snapshot In Movie while Motion Shutter or Time Lapse movie recording is in progress.
92
Recording Movies

Using BEST SHOT

[b]
Scene number
Scene name
Currently selected scene
(with boundary)
BEST SHOT provides you with a collection of sample “scenes” that show a variety of different types of shooting conditions. When you need to change the setup of the camera, simply find the scene that matches what you are trying to achieve, and the camera sets up for it automatically. This helps to minimize the chance of ruined images due to poor exposure and shutter speed settings.

To shoot with BEST SHOT

1. Align the mode dial with [b] (BEST SHOT).
2. Press [SET].
3. Use [8] and [2] to select , and then press [SET].
This will display a menu of BEST SHOT scenes.
4. Use [8], [2], [4], and [6] to move the
boundary to the scene you want to select.
• You can scroll to another page of scenes by
pressing [8] or [2], or by rotating the function ring.
• To return to normal snapshot recording, align the mode dial with [P] (Program Auto).
5. Press [SET] to configure the camera with
the settings for the currently selected scene.
This returns to the REC mode.
• To select a different BEST SHOT scene, repeat the above procedure from step 2.
6. Press the shutter button (if you are shooting a snapshot) or [0] (Movie)
(if you are shooting a movie).
• With some BEST SHOT scenes, the message “Busy... Please wait...” will appear on the monitor screen after you press the shutter button. The camera is in the process of recording an image until the message appears. Keep the camera still. The image processing operation takes some time to complete after the message appears. You will not be able to record another image while the message is displayed.
93
Using BEST SHOT
. Using the Scene Information Screen
To find out more about a scene, select it with the boundary on the scene menu and then rotate the zoom controller in either direction.
• To return to the scene menu, rotate the zoom controller again.
• To scroll between scenes, use [4] and [6].
• To configure the camera with the settings for the currently selected scene, press [SET].
. BEST SHOT Precautions
• Sample images shown on BEST SHOT scene screens were not shot with this camera. They are provided to illustrate the effects and merits of each scene.
• Images shot using a BEST SHOT scene may not produce the results you expected due to shooting conditions and other factors.
• You can modify the camera settings that are configured after you select a BEST SHOT scene. Note, however, that the BEST SHOT settings revert to their defaults when you select another BEST SHOT scene or turn off the camera.
• Snapshot shooting is disabled while the following BEST SHOT scenes are being used. Prerecord (Movie), Manual Exposure Movie
• Movie recording is disabled while the following BEST SHOT scenes are being used. Blurred Background, All-In-Focus Macro, HS Best Selection, HS Anti Shake, Wide Shot, HS Night Shot, Slide Panorama, HDMI TV Output, Triple Shot, HDR, Multi SR Zoom, 60 fps High Speed CS, Make-up BKT, Magnifying Glass
• When the movie recording mode is FHD/STD, movies are recorded using the settings of the selected BEST SHOT scene. For high speed movie recording, BEST SHOT scene settings are ignored and movie recording is performed as it normally is.
• Single SR Zoom cannot be used while shooting with some BEST SHOT scenes.
• With the BEST SHOT scenes below, certain shooting conditions can cause the image area to become narrower than normal. HS Night Scene and Portrait, HS Night Shot
• While shooting with the Fireworks BEST SHOT scene, the focus mode setting is “MF” (Manual Focus) and the focus frame position can be shifted (page 51).
94
Using BEST SHOT
NOTE

Recording Beautiful Portraits (Make-up)

Make-up enables adjustment of human skin tone hues and texture, and softening of facial shadows caused by harsh sunlight for better looking portraits. Make-up can be used with the recording modes listed below.
• Program Auto
• Premium Auto Pro
• Some BEST SHOT scenes
1. In the BEST SHOT Mode, select “Make-up” (page 93).
2. Press [SET], use [8] and [2] to select the (Make-up Settings)
Control Panel option, and then press [SET].
3. Use [8] and [2] to select “Skin Tone” or “Smooth Skin”, and then use
[4] and [6] to change the setting value.
Skin Tone “Tan +6” to “0 (Off)” to “Light +6”
Smooth Skin “0 (Off)” to “+12 (Max.)”
4. Press [SET].
5. Shoot the image.
• The settings below become configured automatically whenever the “Skin Tone” or “Smooth Skin” level setting is something other than “0 (Off)”. – Face Detection: On – Focus Mode: AF (Auto Focus)
95
Using BEST SHOT
NOTE

Shooting Three Versions of an Image with Different Skin Tone Settings (Make-up BKT)

Make-up Bracketing (Make-up BKT) lets you shoot three versions of the same image with the press of the shutter button, each with a different Skin Tone setting. One of the images is shot using the camera’s current Skin Tone setting, while the other two images are shot using variations of the Skin Tone setting.
1. In the BEST SHOT Mode, select “Make-up BKT” (page 93).
2. Press [SET], use [8] and [2] to select the (Make-up Settings)
Control Panel option, and then press [SET].
3. Use [8] and [2] to select “Skin Tone” or “Smooth Skin”, and then use
[4] and [6] to change the setting value.
Skin Tone “Tan +6” to “0 (Off)” to “Light +6”
Smooth Skin “0 (Off)” to “+12 (Max.)”
4. Press [SET].
5. Press the shutter button to shoot.
This will shoot and store three versions of the same image with various “Skin Tone” settings, based on the setting you selected in step 3, above.
• After shooting an image with Make-up BKT, you will not be able to shoot another image until save of the previous image is complete.
• Only two versions of the image will be shot and stored if you shoot with Make-up BKT while “Tan +6” or “Light +6” is selected for “Skin Tone”.
• Movie recording is disabled while Make-up BKT is selected.
96
Using BEST SHOT
NOTE

Shooting a Movie Manually (Manual Exposure Movie)

Use the procedure below to shoot a High Speed Movie with manually configured aperture and shutter speed settings. The ability to manually adjust shutter speed helps to reduce image blur due to subject movement.
1. In the BEST SHOT Mode, select “Manual Exposure Movie” (page 93).
2. Press [SET].
3. Use [8] and [2] to select (Aperture) and then press [SET].
4. Use [8] and [2] to select an aperture setting and then press [4].
5. Use [8] and [2] to select (Shutter Speed) and then press [SET].
6. Use [8] and [2] to select a shutter speed and then press [SET].
7. Press [0] (Movie) to start recording.
8. Press [0] (Movie) again to stop recording.
The maximum file size allowed for a single movie file is 4GB. Movie recording stops automatically when the file size becomes 4GB.
• The settings below can be configured while shooting with this function. Movie Quality: HS120, HS240, HS480, HS1000 Shutter Speed: Auto, 1/125 to 1/10000 seconds (The actual available setting range depends on the movie quality setting.) ISO Sensitivity: Auto, ISO80 to ISO3200 (The actual available setting range depends on the shutter speed and aperture.)
• The functions below cannot be used with this function Anti-shake Functions, Single SR Zoom, Face Detection, Make-up, Triple Self­timer, Remote Capture, EX Finder, Review, Front Shutter, Motion Shutter, snapshot shooting, AF Assist Light, Flash
• The settings in the table below are fixed while shooting with this function.
AF Area Spot
Metering Multi
• Selecting a different BEST SHOT scene or turning off the camera causes the ISO sensitivity setting to be reset to its initial default.
97
Using BEST SHOT
NOTE

Rotating an Image 180 Degrees (Flipped Image)

Use the procedure below to flip a snapshot or movie as you shoot it. This capability comes in handy when the camera is attached to a telescope or other device.
1. In the BEST SHOT Mode, select “Flipped Image” (page 93).
2. Press the shutter button to shoot.
• The settings below can be configured while shooting with this function. Shutter Speed: Auto, 250 to 1/2000 seconds (The actual available setting range depends on the ISO sensitivity and aperture.) ISO Sensitivity: Auto, ISO80 to ISO12800 (The actual available setting range depends on the shutter speed and aperture.)
• The functions below cannot be used with this function. Anti-shake Functions, Face Detection, Make-up, Remote Capture, EX Finder, Front Shutter “CS”, Motion Shutter, AF Area “Intelligent” and “Tracking”
• Selecting a different BEST SHOT scene or turning off the camera causes the following settings to be reset to their initial defaults: ISO sensitivity, aperture, shutter speed.
• Custom Shot setup registration is not supported for images shot with this function.
• If the snapshot size setting is “RAW+JPEG”, RAW image data is stored in normal (unflipped) orientation.

Rotating an Image 180 Degrees when Recording CS Images (Flipped CS Image)

Use the procedure below to flip a burst of CS images. This capability comes in handy when the camera is attached to a telescope or microscope.
1. In the BEST SHOT Mode, select “Flipped CS Image” (page 93).
2. Press [SET].
3. Use [8] and [2] to select (High Speed CS fps), and then press
[SET].
4. Use [8] and [2] to select the continuous shutter (CS) speed and then
press [4].
5. Use [8] and [2] to select (Maximum CS Shots) and then press
[SET].
6. Use [8] and [2] to select the maximum number of shots and then
press [4].
98
Using BEST SHOT
7. Use [8] and [2] to select (Pre-record CS Shots) and then press
NOTE
[SET].
8. Use [8] and [2] to select the number of Prerecord (Still) images and
then press [SET].
• If you select “0 shots”, no pre-record images will be stored when you half-press the shutter button.
9. Half-press the shutter button.
A pre-record buffer is continually updated with images as long as the shutter button is pressed.
• The camera will not emit shutter sounds as it pre-records images.
• Releasing the half-pressed shutter button will cause the contents of the pre-
record buffer to be deleted.
10.
Press the shutter button the rest of the way and hold it down.
Full pressing the shutter button will record the images in the pre-record buffer followed by real-time recorded images. Shooting of images will continue as long as you depress the shutter or until the maximum number of images specified by “High Speed CS fps” is reached.
• The settings below can be configured while shooting with this function. Shutter Speed: Auto, 1/30 to 1/20000 seconds ISO Sensitivity: Auto, ISO80 to ISO12800 (The actual available setting range depends on the shutter speed and aperture.) High Speed CS fps: 3 to 30 Maximum CS Shots: 5 to 30 Pre-record CS Shots: 0 to 25
• The following image sizes cannot be selected while shooting with this function: RAW+JPEG, 3:2, 16:9. If you select Flipped CS Image while either of these image sizes is selected, the camera will automatically switch the images size setting to 12M.
• The snapshot image quality of images shot with this function is Normal.
• The functions below cannot be used with this function. Anti-shake Functions, Single SR Zoom, Face Detection, Make-up, Remote Capture, EX Finder, Review “Type 1”, Front Shutter “AF less” and “CS”, Motion Shutter, Flash, AF Area “Intelligent” and “Tracking”
• You cannot use Triple Self-timer with this function. However, when the “Pre-record CS Shots” setting is something other than 0, Self-timer also cannot be used.
• Selecting a different BEST SHOT scene or turning off the camera causes the following settings to be reset to their initial defaults: High Speed CS fps, Maximum CS Shots, Pre-record CS Shots, ISO sensitivity, aperture, shutter speed.
• Custom Shot setup registration is not supported for images shot with this function.
99
Using BEST SHOT
NOTE

Shooting with Triple Shot

Triple Shot shoots a burst of three images and stores them in memory. This feature is great for making sure you don’t miss those special moments when kids are around.
1. In the BEST SHOT Mode, select “Triple Shot” (page 93).
2. Point the camera at the subject and then half-press the shutter button.
The camera will start pre-recording images at this time.
• If you release the half-pressed shutter button before pressing it the rest of the way down, all of the images currently in the pre-record buffer will be deleted.
3. Press the shutter button all the way down to record.
This will record three images: one of the action before the shutter button is fully pressed plus two real-time images.
• Pressing the shutter button all the way without first half-pressing it will result in only two images being recorded.
• The settings in the table below are fixed while shooting with this function.
Self-timer Off
Flash Flash Off
Image Quality Normal
Single SR Zoom Off
Face Detection On
Focus Mode AF
AF Area “Intelligent” or “Spot”*
* If you select “I Multi” or “O Tracking” for this setting in another mode and
then shoot with Triple Shot, shooting is performed using the “U Spot” setting.
100
Using BEST SHOT
Loading...