Casio 5363 User Manual

MA1308-EA

#!3)/#/-054%2#/,4$

Operation Guide 5363

x Your watch may differ somewhat from the one shown in the illustration. x Some models may use a combination of hands and rotating disks to indicate

information. The word “hand” in this section is used to mean both analog hands and rotating disks.

Stopwatch 1/5-Second Hand

Hour Hand Minute Hand

Click 2

Click 1

Second Hand



Crown

Stopwatch Minute Hand

Stopwatch functions

To adjust the time setting

When the second hand is at 12 o’clock, pull the Click 2.

Rotate the Crown to change the time setting.

Push the Crown back in.

Note

x Take care that you set the correct AM

or PM time.

x When changing the time, move the

minute hand four or ﬁ ve minutes past your ﬁ nal setting, and then back it up to the setting you want.

Crown Operations

Some water-resistant models (100meters, 200meters) have a screw-in crown. When you need to perform a crown operation, rotate it towards you to unscrew it. Then pull the crown out. Avoid applying undue force when pulling. The watch loses its water resistance while the crown is unscrewed. After performing a crown operation, fully screw the crown back in.

If your watch has a rotary bezel...

You can rotate the bezel to align its ▼ mark with the minute hand. Then you will be able to tell how much time has elapsed since aligning the ▼ mark.

Crown out to

24-hour Hand

Day Indicator

To change the day indicator setting

Pull the Crown out to Click 1.

Rotate the Crown to set the day.

Push the Crown back in.

Note

x The day indicator setting uses a 31-

day month. Make adjustments for months of shorter lengths.

x Avoid changing the day indicator

setting between the hours of 9 p.m. and 1 a.m. Otherwise, the day indicator may not change correctly at midnight.

Start

Elapsed time

Current

Crown

Loosen

Using the Stopwatch

The stopwatch measures elapsed time in 1/5 (0.2)-second increments up to 59minutes, 59.8seconds.

Elapsed time

Start Stop Re-start Stop Reset

Split time

Start Split Split release Stop Reset

Two ﬁ nishes

Start Split

Important!

x Do not operate the stopwatch with the crown pulled out.

Note

x The Stopwatch 1/5-Second Hand and Stopwatch Minute Hand move for the ﬁ rst

12hours of an elapsed time measurement. After that, they stop at 0 and they are reset.

First runner ﬁ nishes. Display time of ﬁ rst runner.

A A

B A

A B

Stop

Second runner ﬁ nishes.

Split release

Display time of second runner.

Reset

Correcting the 0 Positions of the Hands

Perform the following procedure if the stopwatch hands do not return to their 0 (zero) positions when you reset the stopwatch.

Pull the Crown out to Click 2.

Hold down A for about two seconds.

x The

Stopwatch Minute Hand

hand setting mode.

x If the hand does not align with 12o’clock, use the B button to adjust it. x Holding down B moves the current hand at high speed.

Hold down A for about two seconds.

x The

Stopwatch 1/5-second Hand

second hand setting mode.

x If the hand does not align with 12o’clock, use the B button to adjust it. x Holding down B moves the current hand at high speed.

After all of the hands are the way you want, push the Crown back in.

Important!

x Timekeeping stops while the crown is pulled out. Correct the current time setting

after performing the above operation.

will perform one full rotation to indicate the minute

will perform one full rotation to indicate the

Speciﬁ cations

Accuracy: ±20seconds average per month Stopwatch: Measuring Capacity: 59'59.8" (60minutes)

Battery: One silver oxide battery (Type: SR927SW) Battery Life: Approximately 5years (2hours stopwatch operation per day) Low Battery Indicator: Second hand moves in 2-second increments when power is low.

Measuring Unit: 1/5 (0.2)second Measurements: Elapsed time; split time; two ﬁ nishes