Casio 3094 User Manual
MA0702-EA
Operation Guide 3093/3094
About This Manual
• The operational procedures for Modules 3093 and 3094
are identical. All of the illustrations in this manual show
Module 3093.
• Button operations are indicated using the letters shown
in the illustration.
• Each section of this manual provides you with the
information you need to perform operations in each
Module 3093
Module 3094
mode.
General Guide
• Press B to change from mode to mode.
• After you perform an operation in any mode, pressing B returns to the Timekeeping
Mode.
Timekeeping Mode Alarm Mode Stopwatch Mode Time Setting Mode
Press .
Timekeeping
Day of week
PM indicator
Hour : Minutes Seconds
Use the Timekeeping Mode to view the current time and
date.
Day
• Day of the week is displayed as follows.
SU : Sunday MO : Monday
TU : Tuesday WE : Wednesday
TH : Thursday FR : Friday
SA : Saturday
To toggle between 12-hour and 24-hour timekeeping
In the Timekeeping Mode, press C to switch between the
12-hour and 24-hour formats.
• With the 12-hour format, the PM indicator (P) appears
for times in the range of noon to 11:59 p.m. and no
indicator appears for times in the range of midnight to
11:59 a.m.
• With the 24-hour format, times are displayed in the
range of 0:00 to 23:59, with 24H indicator.
Alarm
Alarm on indicator
Hourly time
signal on indicator
Alarm time
(Hour : Minutes)
Mode indicator
2. Press A to change the selection in the following sequence.
3. Press C to increase the selected digits. Holding down C changes the number at
high speed.
• The format (12-hour and 24-hour) of the alarm time matches the format you select
for normal timekeeping.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as morning or afternoon (P).
4. After you set the alarm time, press A to return to the Alarm Mode.
• If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Timekeeping Mode automatically.
To stop the alarm
Press A to stop the alarm after it starts to sound.
When the Daily Alarm is turned on, the alarm sounds for
20 seconds at the preset time each day. When the Hourly
Time Signal is turned on, the watch beeps every hour on
the hour.
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing B.
To set the alarm time
1. Hold down A while in the Alarm Mode until the hour
digits start to flash on the display. The hour digits flash
because they are selected.
• This operation automatically turns on the alarm.
Hour
Normal Alarm Mode (No digit flashes)
Minutes
To switch the Daily Alarm and Hourly Time Signal on and off
Press C while in the Alarm Mode to change the status of the Daily Alarm and Hourly
Time Signal in the following sequence.
Both offBoth on
To test the alarm
Hold down C while in the Alarm Mode to sound the alarm.
Daily Alarm
only
Hourly Time
Signal only
Stopwatch
Mode indicator
Minutes Seconds
1/100 second
To measure times with the stopwatch
(a) Elapsed time measurement
Start
(b) Split time measurement
Start
(c) Split time and 1st-2nd place times
Start
The Stopwatch Mode lets you measure elapsed time, split
times, and two finishes. The range of the stopwatch is
59 minutes, 59.99 seconds.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
• Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing B.
Stop Re-start Stop Clear
Split
(SPL displayed)
Split Stop Split release Clear
First runner
finishes.
Display time of
first runner.
Split release Stop Clear
Second runner
finishes.
Display time of
second runner.
1
Operation Guide 3093/3094
Time Setting
Day of week
PM indicator
Hour : Minutes Seconds
3. While the second’s digits are selected (flashing), press C to reset the seconds to
. If you press C while the second’s count is in the range of 30 to 59, the seconds
are reset to
of 00 to 29, the minute’s count is unchanged.
4. While any other digits (besides seconds) are selected (flashing), press C to
increase the number. While the day of the week is selected, pressing C advances
to the next day. Holding down C changes the current selection at high speed.
5. After you set the time and date, press B to return to the Timekeeping Mode.
• If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Timekeeping Mode automatically.
Use the Time Setting Mode to set the current time and
date.
Day
To set the time and date
1. Use B to enter the Time Setting Mode.
• The second’s digits flash because they are selected.
2. Press A to change the selection in the following
sequence.
Seconds Hour
Day of
the Week
and 1 is added to the minutes. If the second’s count is in the range
Day
Minutes
Month
2
Loading...