CASE 580N Specification

580N

BACKHOE LOADER

TIER 4 FINAL CERTIFIED

ENGINE

Model FPT F5BFL413C

Emissions Certification Tier 4 Final

Type Diesel 4-stroke, Turbocharged

Cylinders 4

Bore/Stroke 3.90 x 4.33 in
(99 x 110 mm)

Displacement 207 in3 (3.4 L)

Fuel injection Direct, high pressure
common rail – HPCR

Fuel Diesel

Engine speeds* RPM
Rated speed – full load 2200
Low idle 900 – 1000
High idle – no load 2330 – 2430

Horsepower @ 2200 RPM:
Gross 90 hp (67 kW)
Net w/ viscous fan** 89 hp (66 kW)
Net 83 hp (62 kW)

Maximum torque @ 1400 RPM:
Gross 306 lb·ft (415 N·m)
Net w/ viscous fan 305 lb·ft (413 N·m)
Net 299 lb·ft (405 N·m)

Torque rise at rated speed 43% +/- 5%

Radiator:
Core type Square wave
Core size area 486 in2 (3 145 cm2)
Rows of tubes 5

39° fan:
Style 7 blade suction
Diameter 19.65 in (499 mm)
Ratio 1.1:1

Pump operating angle ratings:
Side to side Rated 35°
Fore and aft Rated 35°
Oil filtration Replaceable,
full flow spin on

NOTE: *Meets federal emission regulations.
**Viscous fan included w/ Cab
Convenience package.

DRIVETRAIN

Transmission – standard:
4F-4R Power Shuttle Synchromesh
Transmission manual gear shift,
fully synchronized

Transmission – optional:
Powershift S-Type, 4F-3R fully synchronized

Specifications below apply to both Power Shuttle
and Powershift S-Type transmission unless
otherwise indicated.

Gear ratios Forward/Reverse
1st 5.603/4.643
2nd 3.481/2.884
3rd 1.584/1.313
4th 0.793/0.657*

Travel speeds Forward Reverse
mph (kph) mph (kph)
1st 3.8 (6.1) 4.5 (7.3)
2nd 6.1 (9.8) 7.3 (11.7)
3rd 13.1 (21.1) 15.7 (25.3)
4th 24.6 (39.6) 29.4 (47.3)*

Torque converter ratio 3.2

Differential-lock On-the-go
push-button activation

Front 4WD/Rear axle:
Differential ratio 2.0/2.5
Planetary hub ratio 6.0/6.4
Total reduction ratio 12.0/16.0

Service brakes:
Individually applied, power assisted,
hydraulically actuated, maintenance-free,
self-adjusting, outboard mounted, wet disc,
2 per side.
Total disc area 384 in2 (0.25 m2)

Parking brakes Trans Mounted
spring-applied hydraulic release – SAHR

NOTE: *4R not available on Powershift S-Type.
Travel speeds at 2293 engine
RPM specified: w/ 19.5 L x 24.0 tires.
Speeds decrease w/ 17.5 L x 24.0 rear tires.

ELECTRICAL

Voltage 12 Volts, negative ground

Alternator 160 amp

Battery 850 cold-cranking amps

Opt. batteries – 2 850 cold-cranking amps

Power plugs – 2 30 amps total

OPERATOR ENVIRONMENT

ROPS/FOPS certified protective canopy;
Anti-vandalism cover for dash – w/ canopy only;
Rear fenders extensions; Coat hook w/ garment
strap; Interior rearview mirror, convex

3.54 in (90 mm) wide x 10.83 in (275 mm) high;
Non-suspension seat – 180° swivel – Vinyl; 2 in
(50 mm) retractable seat belt; Cup holder/storage
tray mounted on left-hand fender; Right-hand
storage compartment w/ lid.

Gauges:
Engine water temperature; Converter oil
temperature; Fuel level; Tachometer/
hourmeter; DEF Level.

Warning lights:
Air cleaner restriction; Alternator; A/C high
pressure; Cold start; Engine oil pressure
low; Hydraulic oil filter bypass; Parking brake
engagement; Low fuel; Water in fuel; Low DEF.

Audible alarms:
Coolant temperature; Engine oil pressure;
Parking brake engagement; Shuttle
engagement/seat position; Backup,
Converter temperature; Low DEF.

Horn Dual switched front and rear

OPERATING WEIGHT

Configuration 1 – SAE Transport:

Standard dipper, 82 in (2.08 m) LL bucket,
2WD, 19.5 L – 24 rear tires, 24 in HD backhoe
bucket, flip over stabilizer pads, 1 Door Cab
w/ Heat and A/C, Cloth Mechanical Suspension
seat, Small front counter weight, S-type
powershift transmission, no operator,
fully fueled.
16,589 lb (7 525 kg)

Configuration 2 – SAE Transport:

No Operator, 1 Door Cab, 4WD, AC, E-hoe,
SPS Shift, Wobble Stick Mechanical BH
Controls, Front Counterweight 4 Speed Manual
Transmission, Boom Guard, Extendahoe®, 82 in
GP Loader Bucket Galaxy 12-16.5 @ 49 psi
Front Tires, Solideal 19.5 L – 24 @ 29 psi
Rear Tires.
17,751 lb (8 052 kg)

Add-on weights:
Cab-over canopy 309 lb (140 kg)
Fabricated stabilizer pads 141 lb (64 kg)
Counterweights 700 lb (318 kg)
Extendahoe® 285 lb (129 kg)
4WD w/ driveshaft guard 283 lb (128 kg)

1 of 7

HYDRAULICS

Pump:
Parker P330 Single Section Gear Pump

Main relief pressure:
Standard 3,350 +/- 50 psi
(231 +/- 3.5 bar)

Filtration:
7-micron, return line, full flow, spin on element,
condition indicator light for filter.

Oil cooler Heavy-duty

Loader flow @ rated engine RPM:

28.5 gpm @ 3,350 psi
(108.0 L/min @ 231 bar)

Loader control valve:
Two or three-spool open center monoblock
valve. Two and three-spool valves have a single
lever manual control for lift and tilt functions.
Three-spool valve uses a proportional
Electro-Hydraulic control for the auxiliary
function. The lift lever has a positive hold “Float”
position and a “return-to-dig” feature. System
Main Relief valve is single stage w/ Manual
Backhoe Controls, dual stage relief valve
w/ Pilot Backhoe Controls.

Loader auxiliary hydraulics w/ proportional thumb
switch w/ detent on loader control handle.

Loader auxiliary hydraulics w/ full available flow:
0 – 28.5 gpm (0 – 108 L/min)

Backhoe flow @ rated engine RPM:

28.5 gpm @ 3,350 psi
(108 L/min @ 231 bar)

Manual backhoe control valve:
Six or seven-spool monoblock open center
control valve. Features “Pro-Control” which
includes custom designed spools for each
individual function along w/ “swing cushioning”
valve for zero-wag swing control. Basic control
valve has an open center parallel circuit for
all functions.

Pilot backhoe control valve:
Six, seven or eight-spool sectional closed
center control valve. Features “Pro-Control”
which includes custom designed spools
for each individual function along w/ “swing
cushioning” valve for zero-wag swing control.
Basic control valve is closed center, w/ circuits
in parallel w/ a post-compensated, flow sharing
feature for simultaneous operation of all circuits.

Unidirectional auxiliary hydraulics:
Unidirectional hydraulic valve is equipped w/ an

adjustable LS relief valve to control attachment
pressure and a 6 position flow control selector
for 6 detented, distinct flow settings.

Actuation:
Manual backhoe controls – cab floor pedal
Pilot controls – left-hand joystick

Bidirectional auxiliary hydraulics*:
Actuation:

Activate the bidirectional Switch located on
the rear console
Manual shift – bidirectional linkage on far right
of backhoe tower
Pilot controls – left-hand joystick.

NOTE: *Available w/ Combo Aux. Hyd. option.

SERVICE CAPACITIES

Fuel tank 35.0 gal (132.0 L)

DEF tank 3.6 gal (13.5 L)

Hydraulic system:
Total 111 qt (105.0 L)
w/ Extendahoe® 117 qt (110.7 L)
Reservoir w/ filter 55 qt (52.4 L)
Reservoir w/o filter 53 qt (50.5 L)

Transmission – total system:
2WD Standard 18 qt (17.0 L)
2WD Powershift 23 qt (21.7 L)
4WD Standard 21 qt (19.4 L)
4WD Powershift 22 qt (20.7 L)

Front axle:
4WD Differential 8.1 qt (7.7 L)
4WD Planetaries – each 0.5 qt (0.5 L)

Rear axle:
Differential and planetaries 14.4 qt (13.6 L)

Engine oil w/ filter 8.5 qt (8.0 L)

Cooling system:
w/ heater 19.0 qt (18.0 L)
w/o heater 18.3 qt (17.3 L)

Window washer reservoir 3.0 qt (2.8 L)

OTHER SPECIFICATIONS

Front tires:
2WD 11.0 L x 16.0, 10-ply rating
4WD 12.0 L x 16.5, 8-ply rating

Rear tires:
2/4WD 19.5 L x 24.0, 10-ply rating
2/4WD 17.5 L x 24.0, 10-ply rating

Loader:
Bucket position indicator; Lifting lugs on
standard bucket; Single lever control w/
self-leveling and return-to-dig; Hand operated
clutch disconnects on loader and shift levers,
single lever 4-function loader control: lift, dump,
clutch cut-out, differential lock.

Turning radius*: Curb to Curb
2WD:
Brakes on 10 ft 8 in (3.24 m)
Brakes off 12 ft 4 in (3.76 m)

4WD – engaged:
Brakes on 11 ft 4 in (3.45 m)
Brakes off 13 ft 10 in (4.21 m)

4WD – disengaged:
Brakes on 11 ft 0 in (3.36 m)
Brakes off 12 ft 3 in (3.72 m)

Backhoe:
Over center design, Fabricated “S” boom;
Open-center hydraulics – Pro Control System.

NOTE: *Turning radius dimensions curb to curb
w/ 17.5 L x 24.0 rear tires.

LOADER BUCKET SIZES

Type Width Weight Struck Heaped Capacity

Long Lip Bucket without bolt-on edge 82 in (2.08 m) 683 lb (310 kg) 0.88 yd3 (0.67 m3) 1.03 yd3 (0.79 m3)
93 in (2.36 m) 1,188 lb* (539 kg) 1.10 yd3 (0.84 m3) 1.29 yd3 (0.99 m3)

4 IN 1® Bucket with bolt-on edge 82 in (2.08 m) 1,572 lb* (713 kg) 0.85 yd3 (0.65 m3) 1.05 yd3 (0.80 m3)

NOTE: * Weight of 4 IN 1® bucket includes edges, cylinders and tube lines.

BACKHOE BUCKET SIZES

Type Width Weight Heaped Capacity

General Purpose Trenching Buckets 18 in (457 mm) 232 lb (105 kg) 4.70 ft3 (0.13 m3)
24 in (610 mm) 272 lb (123 kg) 6.26 ft3 (0.18 m3)

Universal Buckets 12 in (305 mm) 295 lb (137 kg) 3.40 ft3 (0.10 m3)
18 in (457 mm) 356 lb (162 kg) 5.30 ft3 (0.15 m3)
24 in (610 mm) 427 lb (194 kg) 7.70 ft3 (0.22 m3)
30 in (762 mm) 489 lb (222 kg) 10.20 ft3 (0.29 m3)
36 in (914 mm) 552 lb (251 kg) 12.70 ft3 (0.36 m3)

High Capacity Buckets 24 in (610 mm) 447 lb (203 kg) 8.50 ft3 (0.24 m3)

580N

2 of 7

J

M

D

N

O

Line drawings are for illustrative purpose only and may not be exact representation of unit.

F

H

C

G

L

K

A

B

E

LOADER DIMENSIONS

Long Lip Bucket 4 IN 1® Bucket

A. Overall operating height – fully raised 13 ft 9 in (4.18 m) 13 ft 8 in (4.16 m)

Height to:

B. Bucket hinge pin fully raised 11 ft 3 in (3.42 m) 11 ft 3 in (3.42 m)
C. Bucket hinge pin at SAE carry 13.6 in (345 mm) 13.6 in (345 mm)

D. Dump angle at full height 47° 47°

E. Dump clearance at full height, 45° dump:

Bucket 8 ft 10 in (2.69 m) 8 ft 11 in (2.71 m)
Clam open — 9 ft 8 in (2.96 m)

F. Dump reach at full height, 45° dump:
Bucket 31.5 in (801 mm) 29.1 in (738 mm)
Clam open — 15.3 in (388 mm)

Bucket rollback:

G. @ Groundline 42° 42°
H. @ SAE carry 42° 42°
J. @ Full height Adjustable Adjustable

K. Digging depth below grade:

Bucket flat 6.1 in (155 mm) 4.8 in (122 mm)
Clam open – dozing — 4.1 in (103 mm)

L. Reach from front axle centerline – bucket on ground 6 ft 10 in (2.08 m) 6 ft 10 in (2.03 m)

Lift capacity to full height 6,803 lb (3 086 kg) 6,459 lb (2 930 kg)

Breakout force:
Lift cylinders 9,506 lb (4 228 daN) 9,276 lb (4 126 daN)
Dump cylinders 10,622 lb (4 724 daN) 11,312 lb (5 032 daN)

Bucket cutting edge width 82.5 in (2.09 m) 82.0 in (2.08 m)

Maximum grading angle 114° 114°

Maximum clam opening — 38.3 in (972 mm)

Moldboard height — 36.8 in (934 mm)

Raising time to full height 4.6 sec 4.6 sec

Bucket dumping time 1.1 sec 1.1 sec

Lowering time:
Power down 2.6 sec 2.6 sec
Return-to-dig 3.6 sec 3.6 sec

Clam:
Open time — 1.0 sec
Close time — 1.0 sec

NOTE: Loader dimensions taken with 4WD, 19.5 L x 24.0 rear tires.

580N

3 of 7

DIMENSIONS

2WD with 19.5 L x 24.0 tires 4WD with 19.5 L x 24.0 tires

M. Overall transport length:

Long Lip bucket with Quick Coupler 23 ft 5 in (7.14 m) 23 ft 4 in (7.10 m)
4 IN 1® bucket with Quick Coupler 23 ft 3 in (7.07 m) 23 ft 1 in (7.04 m)
Long Lip bucket with Straight Links 23 ft 6 in (7.15 m) 23 ft 4 in (7.12 m)
4 IN 1® bucket with Straight Links 23 ft 3 in (7.09 m) 23 ft 2 in (7.06 m)

Overall transport width – rear tires 6 ft 10 in (2.07 m) 6 ft 10 in (2.07 m)

Height:
To top of canopy 8 ft 9 in (2.66 m) 8 ft 9 in (2.66 m)
To top of cab 8 ft 11 in (2.72 m) 8 ft 11 in (2.72 m)
To top of exhaust stack 8 ft 7 in (2.62 m) 8 ft 7 in (2.61 m)
N. Transport 10 ft 10 in (3.30 m) 11 ft 1 in (3.37 m)

Ground clearance at backhoe frame 15.0 in (380 mm) 15.0 in (380 mm)

Angle of departure 15.3° 19.0°

Front wheel tread:

11.0 L x 16.0 67.5 in (1.71 m) 67.5 in (1.71 m)

12.0 L x 16.5 67.7 in (1.72 m) 67.7 in (1.72 m)

Rear wheel tread:

17.5 L x 24.0 63.1 in (1.60 m) 63.1 in (1.60 m)

19.5 L x 24.0 61.2 in (1.55 m) 61.2 in (1.55 m)

Width over tires:

11.0 L x 16.0 79.3 in (2.01 m) 79.3 in (2.01 m)

12.0 L x 16.5 81.1 in (2.06 m) 81.1 in (2.06 m)

17.5 L x 24.0 81.7 in (2.07 m) 81.7 in (2.07 m)

19.5 L x 24.0 81.4 in (2.07 m) 81.4 in (2.07 m)

O. Wheelbase 84.0 in (2.13 m) 84.5 in (2.15 m)

CYLINDERS

Bore Diameter Rod Diameter Stroke Closed Length

Loader:
Lift – 2 3.25 in (82.6 mm) 1.75 in (44.5 mm) 28.86 in (733.0 mm) 41.81 in (1 062.0 mm)
Dump – 2 3.00 in (76.2 mm) 1.50 in (38.1 mm) 20.33 in (516.5 mm) 30.31 in (769.9 mm)
4 IN 1® clam – 2 3.00 in (76.2 mm) 1.75 in (44.5 mm) 9.08 in (230.6 mm) 19.62 in (498.3 mm)

Backhoe:
Boom 4.50 in (114.3 mm) 2.25 in (57.2 mm) 38.22 in (971.5 mm) 52.82 in (1 341.6 mm)
Dipperstick 4.25 in (108.0 mm) 2.25 in (57.2 mm) 25.14 in (628.5 mm) 39.65 in (1 007.0 mm)
Bucket 3.25 in (82.6 mm) 2.25 in (57.2 mm) 35.35 in (897.9 mm) 48.17 in (1 223.6 mm)
Extendahoe® 3.00 in (76.2 mm) 1.75 in (44.5 mm) 42.05 in (1 068.0 mm) 56.22 in (1 428.0 mm)
Swing – 2 3.75 in (95.3 mm) 2.00 in (50.8 mm) 11.50 in (292.0 mm) 24.44 in (620.8 mm)
Stabilizer – 2 4.25 in (108.0 mm) 2.25 in (57.2 mm) 21.37 in (542.9 mm) 33.87 in (860.2 mm)

AXLE RATINGS

Front – 2WD Rear Front – 4WD

Maximum static 70,821 lb (32 124 kg) 90,145 lb (40 889 kg) 64,613 lb (29 308 kg)

Dynamic operating 44,261 lb (20 076 kg) 56,200 lb (25 492 kg) 39,328 lb (17 839 kg)

Static operating 17,704 lb (8 030 kg) 22,480 lb (10 197 kg) 15,732 lb (7 136 kg)

Oscillation – front axle 22° total – 11° side to side — 22° total – 11° side to side

580N

4 of 7

BACKHOE LIFT CAPACITIES

Standard Backhoe Extendahoe

®

Retracted Extended

Boom Lift Lift Capacity

lb (kg)

+16 ft (4.87 m) — — 1,693 (768)

+14 ft (4.27 m) 2,472 (1 121) 2,271 (1 030) 1,979 (897)

+12 ft (3.66 m) 2,857 (1 296) 2,644 (1 199) 2,124 (964)

+10 ft (3.05 m) 2,966 (1 345) 2,748 (1 246) 2,172 (985)

+8 ft (2.44 m) 2,983 (1 353) 2,761 (1 252) 2,169 (984)

+6 ft (1.83 m) 2,963 (1 344) 2,739 (1 242) 2,173 (985)

+4 ft (1.22 m) 2,929 (1 329) 2,701 (1 225) 2,165 (982)

+2 ft (0.61 m) 2,892 (1 312) 2,662 (1 207) 2,153 (977)

Ground Level 2,858 (1 297) 2,625 (1 191) 2,153 (977)

-2 ft (0.61 m) 2,834 (1 285) 2,598 (1 178) 2,145 (973)

-4 ft (1.22 m) 2,827 (1 282) 2,588 (1 174) 2,143 (972)

-6 ft (1.83 m) 2,853 (1 294) 2,609 (1 183) 2,154 (977)

-8 ft (2.44 m) 2,949 (1 338) 2,698 (1 224) 2,189 (993)

-10 ft (3.05 m) 3,319 (1 506) 3,053 (1 385) 2,270 (1 030)

-12 ft (3.66 m) — — 2,429 (1 102)

-14 ft (4.27 m) — — 3,115 (1 413)

Dipper Lift

+14 ft (4.27 m) — — 3,154 (1 431)

+12 ft (3.66 m) 4,343 (1 970) 4,139 (1 877) 2,981 (1 352)

+10 ft (3.05 m) 4,027 (1 827) 3,826 (1 735) 2,823 (1 281)

+8 ft (2.44 m) 4,112 (1 865) 3,910 (1 774) 2,855 (1 295)

+6 ft (1.83 m) 4,563 (2 070) 4,357 (1 976) 3,010 (1 365)

+4 ft (1.22 m) 5,398 (2 449) 5,177 (2 348) 2,948 (1 337)

+2 ft (0.61 m) — — 3,486 (1 581)

Lift Capacity

lb (kg)

Lift Capacity

lb (kg)

BACKHOE OPERATIONAL DATA

Standard Backhoe Extendahoe

®

Retracted Extended

Digging depth:
Maximum 14 ft 9 in (4.50 m) 14 ft 9 in (4.50 m) 18 ft 3 in (5.55 m)
2 ft (610 mm) flat bottom 14 ft 8 in (4.46 m) 14 ft 8 in (4.46 m) 18 ft 1 in (5.52 m)
8 ft (2.44 m) flat bottom 13 ft 8 in (4.16 m) 13 ft 8 in (4.16 m) 17 ft 4 in (5.29 m)

Overall reach from:
Rear axle centerline 21 ft 11 in (6.68 m) 21 ft 11 in (6.68 m) 25 ft 4 in (7.72 m)
Swing pivot 18 ft 4 in (5.57 m) 18 ft 4 in (5.57 m) 21 ft 8 in (6.60 m)

Loading height 11 ft 9 in (3.59 m) 11 ft 9 in (3.59 m) 14 ft 1 in (4.30 m)

Loading reach – dipper retracted 6 ft 9 in (2.04 m) 6 ft 9 in (2.04 m) 9 ft 4 in (2.84 m)

Swing arc 180° 180° 180°

Bucket rotation:
Straight links 175.6° 175.6° 175.6°
Mechanical coupler 198.0° 198.0° 198.0°

Stabilizer spread – centers:
Flip pad 9 ft 5 in (2.87 m) 9 ft 5 in (2.87 m) 9 ft 3 in (2.81 m)
Cast Pad 9 ft 9 in (2.97 m) 9 ft 9 in (2.97 m) 9 ft 7 in (2.92 m)

Digging force:
Bucket cylinder 11,517 lb (51 228 N) 11,517 lb (51 228 N) 11,517 lb (51 228 N)
Dipper cylinder 6,710 lb (29 484 N) 6,710 lb (29 484 N) 4,887 lb (21 738 N)

Leveling angle:
Flip pad 12.8° 12.8° 12.8°
Cast pad 13.8° 13.8° 13.8°

580N

5 of 7

STANDARD EQUIPMENT

OPERATOR ENVIRONMENT

See page 1

ENGINE

FPT F58FL4I3C diesel
Cooled EGR
Selective Catalytic Reduction – SCR
Full ow engine oil lter
Air cleaner – replaceable dry type

with radial seal
Aspirated air cleaner
Radiator with de-aeration bottle
Antifreeze to -34° F (-37° C)
Throttles, both rotary hand and foot
Self adjusting belt

DRIVETRAIN

Front axle, as selected:
2WD heavy-duty front axle with

11.0 L x 16.0 tires

4WD heavy-duty mechanically driven front

axle, with 12.0 L x 16.5 tires
Rear axle:
2/4WD heavy-duty outboard planetary drive,
with 17.5 L x 24.0 tires
4F-4R Power Shuttle
Synchromesh transmission
Torque converter – 11.8 in (300 mm)
On-the-go electric 4WD control
Electric F/R shuttle control
Electric differential lock control,
with push-button activation on
the loader control lever
Park brake, spring-applied, hydraulic

release - SAHR

HYDRAULICS

Gear pump:

28.5 gal/min @ 3,350 psi

(107.9 L/min @ 231 bar)
Heavy-duty hydraulic oil cooler
7-micron, spin on oil lter

LOADER

See page 2

BACKHOE

See page 2

OTHER

Forward tilt engine hood
Replaceable, molded front bumpers
Front/Rear tie downs
Reective logos
Lights – cab and canopy:

2 front driving

2 rear tail/stop

2 front ashers/turn

2 rear ashers/turn
Lights – cab only:
Adjustable halogen work lights – 55 W:

2 front

2 side – left and right

4 rear
Lights – canopy only:
Adjustable halogen work lights – 55 W:

2 side – left and right

2 rear

TELEMATICS

CASE SiteWatch™ Telematics – includes

hardware and a 3-yr Advanced
data subscription

580N

6 of 7

OPTIONAL EQUIPMENT

OPERATOR ENVIRONMENT

Speed Selectable Auto Ride Control –

4WD models
Standard Ride Control – 2WD models
Comfort Steering with momentary latching

switch, two-speed steering pump and

3rd/4th gear cutout
ROPS/FOPS certied protective cab with rear

wipers and oor mat
Cab Convenience Package containing

pull-down sun visor, window washer – front

and rear, left-hand storage tray, deluxe

interior package, tilt steering column,

Sound Reduction Package for cab models

– levels reduced to 72 dB (A), right-hand

threshold storage box, viscous fan
Air-conditioning for cab models
Mechanical suspension seat with ip-up

armrests, 180° swivel, heated cloth or vinyl,

adjustable seat and weight, backrest angle,

lumbar and cushion angle
Air Ride suspension seat with ip-up

armrests, 180° swivel, heated, electric

height adjustment, adjustable backrest and

lumbar support – cab units cloth, canopy

units vinyl
Pull-down sun visor for canopy models
Radio, AM/FM Stereo/WB, MP3 auxiliary

input – cab models
3 in (75 mm) seat belt for mechanical and

air-suspension seat

ENGINE

Cold Weather Starting Aid

with dual 12 Volt batteries and glow plugs

Block heater

DRIVETRAIN

Powershift S-Type transmission, 4F-3R fully

synchronized, electronic transmission
controller and kick down in loader control

lever – 2WD or 4WD

Heavy-duty outboard planetary drive

without 19.5 L x 24.0 tires

LOADER

Auxiliary hydraulics for loader-mounted

equipment with thumb-operated

proportional control
Hydraulic front quick coupler
Loader linkage without loader bucket
Tool portfolio of additional attachments
Buckets – see page 2

BACKHOE

Auxiliary backhoe unidirectional hydraulics
Auxiliary backhoe combo hydraulics:

Hand lever operated for bidirectional

manual controls

Button operated for pilot controls, includes

unidirectional and bidirectional
Auxiliary hydraulics with ow from

0 to 28 gal/min (0 to 106 L/min)
Extendahoe

®

Two-lever controls - backhoe or Extendahoe

Pilot operated control system:

Fingertip proportional Electro-Hydraulic
stabilizer controls
Thumb-operated proportional
Electro-Hydraulic Extendahoe® control
Thumb-operated horn button
Thumb-operated auxiliary hydraulic control
Innitely adjustable towers
In-cab switchable “excavator to backhoe”

control pattern change
Flip over stabilizer pads
Cemetery/Street pads
Case mechanical quick coupler
Universal coupler – CAT/Deere compatible

Buckets – see page 2

OTHER

Front:

11.0 L x 16.0 10-ply or 12.0 L x 16.5 8-ply

Rear:

17.5 L x 24.0 10-ply or 19.5 L x 24.0 10-ply
Special paint
Canopy lights – Additional 2 front and 2 rear

halogen lights – 55 W
Tool box – bolt-on, step-mounted
Front counterweights:

700 lb and 1,100 lb (318 kg and 500 kg)
Rotating beacon
Master disconnect switch and

remote jump-start terminals
Eco-Mode – Detent on backhoe hand

throttle, push button switch on desk

®

CaseCE.com

©2017 CNH Industrial America LLC. All rights reserved. CASE is a
trademark registered in the United States and many other countries,
owned by or licensed to CNH Industrial N.V., its subsidiaries or
affiliates. CNH Industrial Capital is a trademark in the United States
and many other countries, owned by or licensed to CNH Industrial
N.V., its subsidiaries or affiliates. Printed in U.S.A.
post-consumer fiber.

Form No. CCE201702580N

Replaces Form No. CCE201603580NT4

580N

Contains 10%

IMPORTANT: CASE Construction Equipment Inc. reserves the right
to change these specifications without notice and without incurring
any obligation relating to such change. Availability of some models
and equipment builds vary according to the country in which the
equipment is used. The illustrations and text may include optional
equipment and accessories and may not include all standard
equipment. Your CASE dealer/distributor will be able to give you
details of the products and their specifications available in your area.

CASE Construction Equipment
friendly.

NOTE: All engines meet current EPA
emissions regulations. All specifications are
stated in accordance with SAE Standards or
Recommended Practices, where applicable.

Always read the Operator’s Manual before
operating any equipment. Inspect equipment
before using it, and be sure it is operating
properly. Follow the product safety signs and
use any safety features provided.

is biodiesel-

7 of 7