Casablanca Fan Company 54007, 54006, 54005 User Manual

Download

30 inches

7 feet

Ladder

Table of Contents

www.CasablancaFanCo.com

1.888.227.2178

Congratulations on purchasing your new Casablanca® ceiling fan! It will provide comfort and

performance in your home or ofce

for many years. This installation and operation manual contains complete instructions for installing and operating your fan.

We are proud of our work and appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world.

To register your fan please visit: www.CasablancaFanCo.com/register

Blades Troubleshooting

What to Expect with

Your Installation

Tools Needed

PAG E

Preparation

PAG E

Downrod

Switch Housing Light Kit

Mounting Options

PAG E

Wiring Canopy

PAG E

Maintenance

& Cleaning

Ceiling Bracket

Installation

PAG E

M6004-01 • 08/13/12 • © Casablanca Fan Company

What to Expect with Your Installation

www.CasablancaFanCo.com

1.888.227.2178

1.888.227.21781.888.227.2178

Must be able to secure the fan to building structure or fan-rated outlet box

You may need a friend to help you.

Check box to see fan weight

If you are unfamiliar with wiring, use a

qualied electrician.

Know your wiring

Ceiling angles greater

than 34° will require an

Angled Mounting Kit. See page 4 for details.

Assess ceiling angle

30 inches

from blade tip to nearest wall or obstruction

Assess location

Standard Downrod

for ceilings 8-10 feet high

Shorter Downrod

for fans installed close to ceiling

Longer Downrod

for ceilings 10 feet or higher

Select a downrod length

7 feet

From bottom

edge of blade

to the oor

Read and Save These Instructions

This product conforms to UL Standard 507.

WARNINGS

w.1 - To reduce the risk of re, electrical shock, or

personal injury, mount fan directly from building structure and/or an outlet box marked acceptable for

fan support of 70 lbs (31.8 kg) and use the mounting

screws provided with the outlet box.

w.2 - To avoid possible electrical shock, before installing or servicing your fan, disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location. If you cannot lock the circuit breakers in the off position, securely fasten a prominent warning device, such as a tag, to the service panel.

w.3 - To reduce the risk of re, electrical shock, or motor

damage, use only Casablanca Solid State Speed Controls.

w.4 - To reduce the risk of personal injury, do not bend the blade brackets when installing the blade brackets, balancing the blades, or cleaning the fan. Do not insert foreign objects in between rotating fan blades.

CAUTIONS

c.1 - All wiring must be in accordance with national and local electrical codes ANSI/NFPA 70. If you are unfamiliar

with wiring, use a qualied electrician.

c.2 - Use only Casablanca replacement parts.

M6004-01 • 08/13/12 • © Casablanca Fan Company

Tools Needed

www.CasablancaFanCo.com

1.888.227.2178

Ladder

Pliers Wire Strippers

Power Drill

(optional)

If mounting to a support structure, you will also need these tools.

9/64” Drill Bit

(optional)

M6004-01 • 08/13/12 • © Casablanca Fan Company

Screwdrivers

CEILING

Mounting Options

www.CasablancaFanCo.com

1.888.227.2178

OPTION

If you have a at ceiling:

WALL

Hang your fan by a standard downrod (included).

Standard Mounting

Support Structure

OPTION

If you have an angled ceiling:

1. You will need a longer downrod (sold separately).

2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately).

Use the three steps below to determine if your ceiling angle is greater than 34°

Angled Mounting

Standard Mounting Style

Ceiling

Outlet Box

(required)

Angled Mounting Style

Ceiling

Outlet Box

(required)

FOLD

on dotted line

34°

Guide Touches

BOTH Ceiling & Wall

You need ONLY

a Longer

Downrod

*most common

2 3

PLACE

against wall

Guide Touches

but NOT Ceiling

You need BOTH

a Longer

Downrod &

an Angled

Mounting Kit

SLIDE

toward ceiling

Wall

to hang the fan from a at ceiling.

M6004-01 • 08/13/12 • © Casablanca Fan Company

Use Standard Mounting

or Low-Prole Mounting

Use Angled Mounting

to hang the fan from a

vaulted or angled ceiling.

Ceiling Bracket Installation

Turn Power

OFF

www.CasablancaFanCo.com

For angled ceilings, point

opening toward peak.

1.888.227.2178

Make sure all four (4) bumpers

are still attached.

To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet

box associated with the wall switch location.

Use wood screw

(included) when securing

to support structure with approved electrical outlet box. Drill 9/64” pilot holes in support structure to aid in securing ceiling bracket

with hardware found in

the hardware bag.

M6004-01 • 08/13/12 • © Casablanca Fan Company

Use machine screw

(provided with outlet

box) when securing to

existing ceiling fan-rated

outlet box. Make sure

it is securely installed

and is acceptable for fan

support of 31.8 kg (70 lbs)

or less.

If you are unable to do this,

call Technical Support at

1-888-227-2178.

Refer to warning w.1 on pg. 2

Ceiling Bracket Installation (continued)

Preparation

Remove the shipping blocks from

the motor. Save the ve screws.

They will be needed for blade iron

installation.

www.CasablancaFanCo.com

Time Saver Tip: Get a helper

to insert grommets, found in

the hardware bag, into the

blades while you’re doing the

next couple of steps.

1.888.227.2178

M6004-01 • 08/13/12 • © Casablanca Fan Company

Downrod

www.CasablancaFanCo.com

1.888.227.2178

Standard Downrod

for ceilings 8-10’ high

Option 1Option 2

Shorter Downrod

for fans installed close to ceiling

Included

(pre-assembled)

Longer Downrod

for angled ceilings or

Option 3

ceilings 10’ or higher

skip to next page

If you need a different downrod length follow these steps:

Steps 1-5 to remove standard downrod pipe

1 2 3 4 5

Slide

678910

Included

Sold Separately

Steps 6-10 to reassemble with new pipe

M6004-01 • 08/13/12 • © Casablanca Fan Company

Downrod (continued)

www.CasablancaFanCo.com

1.888.227.2178

KEEP!

Remove the pre-installed

setscrew so that the downrod

can be inserted.

Hand tighten the downrod (at

least 4-5 full turns) until it stops.

8”

M6004-01 • 08/13/12 • © Casablanca Fan Company

3/8”

8”

(not to scale)

The wires can be cut, but

leave at least 8” extending

from the top of the downrod.

Tighten the setscrew

with pliers. DO NOT

HAND TIGHTEN.

3/8”

If the setscrew is not tightened securely, the fan may fall.

Downrod (continued)

Put the wires and downrod through the

canopy. Let the canopy sit loosely on top

DO NOT PICK THE FAN UP BY THE

www.CasablancaFanCo.com

1.888.227.2178

of the fan.

CANOPY OR WIRES. Place the downrod

ball into the slot in the ceiling bracket.

M6004-01 • 08/13/12 • © Casablanca Fan Company

Wiring

White

(Ungrounded)

Black

Blue

(Grounded)

(Ungrounded)

Using an orange wire

connector from

the hardware bag,

connect the 3 grounding

wires (green, green/

yellow stripe, or bare

copper) coming from the

ceiling, downrod, and

hanging bracket.

Green/Yellow Stripe

(Grounding)

Green/Yellow

Stripe

Note: To connect the wires,

www.CasablancaFanCo.com

1.888.227.2178

hold the bare metal leads

together and place a wire

connector over them, then twist

clockwise until tight.

(Grounded)

(Ungrounded)

For Dual Switches

Using orange wire

connectors from

the hardware bag,

For a Single Switch

Using the orange wire

White

Blue

Black

connectors from

the hardware bag, connect

the black wire (ungrounded)

from the ceiling to the black

and the blue wires from the fan. Connect the white wire

(grounded) from the ceiling to

the white wire from the fan.

connect the white wire

(grounded) from the

ceiling to the white wire

from the fan.

Connect the black wire

(ungrounded) from the

ceiling to the black wire

from the fan. Connect the

second (ungrounded) wire

from the ceiling to the blue

wire from the fan.

Refer to CAUTION c.1 on pg. 2

Turn the splices upward and push them carefully back through the hanger bracket into the outlet box. Spread the wires apart, with the grounded wires on one side of

the outlet box and the ungrounded wires on the other side of the outlet box.

M6004-01 • 08/13/12 • © Casablanca Fan Company

Canopy

Screw

Holes

www.CasablancaFanCo.com

1.888.227.2178

Position the canopy so that, when

lifted into place, the canopy ts into

the hanging bracket as shown.

Lift the canopy into place so that

the screw holes are aligned.

Insert the two canopy screws

found in the hardware bag.

Note: Fan style may vary.

Blades

Insert grommets found in the hardware

Lightly attach the blade irons to the

Remember the screws that

you kept after removing the

shipping blocks (page 6)? You

need them plus ve more from

hardware bag for this step.

www.CasablancaFanCo.com

1.888.227.2178

bag into the holes in the blades, then secure each blade to a blade iron with screws found in the hardware bag.

motor with screws found in

the hardware bag, then securely

tighten after both screws are attached.

Your blades are shielded with Dust Armor® which

is a nanotechnology coating that repels dust. For

cleaning the fan, use soft brushes or cloths to prevent

scratching. Cleaning agents may damage the nishes.

Switch Housing

www.CasablancaFanCo.com

1.888.227.2178

Screw two (2) housing assembly screws

from the hardware bag halfway into

the motor housing. It does not matter

which two screw holes you choose.

Feed the wire plug through the center

hole of the upper switch housing, then

wrap keyhole slots around the screws and

twist counterclockwise.

Insert the third screw, found in

the hardware bag, into place and

then tighten all three (3) screws.

Make sure the upper switch housing is securely attached to the mounting plate. Failure to properly

secure all 3 assembly screws could result in the switch housing xture falling.

Light Kit

Shade

Socket

Socket Ring

Socket Ring Tool

www.CasablancaFanCo.com

1.888.227.2178

Remove the socket rings from the sockets.

Install the shades onto the sockets. Install the socket rings onto the sockets. Tighten them by turning clockwise with

the socket ring glass tool.

For questions regarding removing a light kit, call

customer service 1-888-227-2178.

Connect the plugs from the upper and

lower switch housings. Make sure to line

up the colored markings on

the connectors.

Lift the lower switch housing up until the

holes line up with the screw holes in the

upper switch housing.

Light Kit (continued)

www.CasablancaFanCo.com

CONGRATULATIONS!

YOU’RE DONE!

1.888.227.2178

Insert three (3) switch

housing screws found in the

hardware bag.

Make sure the lower switch housing is securely attached to

the upper switch housing. Failure to properly secure all 3 assembly screws could result in the light xture falling.

Install the CFL bulbs into the

sockets. When necessary, replace

with bulbs of same wattage.

Connect the pull chain pendants

to the short chains coming from

the switch housing.

See next page for fan operation instructions.

Note: Glass shade style and number of lights may vary.

Maintenance & Cleaning

Turn Power

Reverse

Switch

www.CasablancaFanCo.com

1.888.227.2178

The pull chain controls the fan: high,

medium, low, extra low, and off.

The light pull chain controls the

power to the light xture: on and off.

To switch the direction of air

ow, move the reverse switch to

the opposite position.

For cleaning the fan, use soft

brushes or cloths to prevent

scratching. Cleaning products

may damage the nishes.

Troubleshooting

www.CasablancaFanCo.com

1.888.227.2178

Fan doesn’t work

• Make sure power switch is on.

• Pull the pull chain to make sure

it is on.

• Push the motor reversing switch rmly left or right to ensure that

it is engaged.

• Check the circuit breaker to ensure the power is turned on.

• Make sure the blades spin freely.

• Turn off power from the circuit

breaker, then loosen the canopy and check all the connections according to the wiring diagram on page 10.

• Check the plug connection in the switch housing.

Excessive wobbling

• Tighten all of the blade and blade iron screws until they are snug.

• Turn the power off, support the fan carefully, and check that the hanger ball is properly seated.

• Use the provided balancing kit and instructions to balance the fan.

Noisy Operation

• Tighten the blade and blade iron screws until they are snug.

• Check to see if any of the blades are cracked. If so, replace all of the blades.

AUTHORIZED SERVICE CENTERS

For the most updated listing of Casablanca Authorized Service Centers, visit www.CasablancaFanCo.com or

call toll free 1-888-227-2178.

Casablanca Fan Company 54007, 54006, 54005 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual