Casablanca Fan CFC2922 Owner Manual

Download

30 inches

7 feet

Ladder

Table of Contents

www.CasablancaFanCo.com

1.888.227.2178

Congratulations on purchasing your new Casablanca® ceiling fan! It will provide comfort and performance in

your home or ofce for many years.

This installation and operation manual contains complete instructions for

installing and operating your fan.

We are proud of our work and appreciate the opportunity to supply you with the best ceiling fan available

anywhere in the world.

To register your fan, please visit:

www.CasablancaFanCo.com/register

Save your receipt for proof of purchase.

Upper Switch Housing TroubleshootingLED Assembly Globe

What to Expect with

Your Installation

Tools Needed

PAG E

WiringDownrod

PAG E

Operation

Mounting Options

PAG E

Wall Control

PAG E

Maintenance

& Cleaning

Ceiling Bracket

PAG E

Canopy

PAG E

What to Expect with Your Installation

If you are unfamiliar with wiring, use a

qualied electrician.

Must be able to secure the fan to building structure or

fan-rated outlet box

You may need a

friend to help you.

Know your wiring

30 inches

from blade tip to nearest wall or obstruction

from bottom

edge of blade

Assess location

Standard Downrod

7 feet

to the oor

www.CasablancaFanCo.com

1.888.227.2178

Read and Save These Instructions

This product conforms to UL Standard 507.

WARNINGS

w.1 - To reduce the risk of re, electrical shock, or personal

injury, mount fan directly from building structure and/or an

outlet box marked acceptable for fan support of 70 lbs (31.8 kg) and use the mounting screws provided with the outlet box.

w.2 - To avoid possible electrical shock, before installing or

servicing your fan, disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch

location. If you cannot lock the circuit breakers in the off

position, securely fasten a prominent warning device, such as a

tag, to the service panel.

w.3 - To reduce the risk of re, electrical shock, or motor damage, use only Casablanca Solid State Speed Controls.

w.4 - To reduce the risk of personal injury, do not bend the blade

brackets when installing the blade brackets, balancing the blades,

or cleaning the fan. Do not insert foreign objects in between rotating fan blades.

CAUTIONS

Check box to see fan weight

Ceiling angles greater

than 34° will require an Angled Mounting Kit. See page 4 for details.

Assess ceiling angle

Longer Downrod

for angled ceilings or high ceilings

Select a downrod length

c.1 - All wiring must be in accordance with national and local electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualied electrician.

c.2 - Use only Casablanca replacement parts.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications.

Tools Needed

www.CasablancaFanCo.com

1.888.227.2178

Ladder

Pliers Wire Strippers

Power Drill

(optional)

If mounting to a support structure, you will also need these tools.

9/64” Drill Bit

(optional)

Screwdrivers

CEILING

Mounting Options

www.CasablancaFanCo.com

1.888.227.2178

OPTION

If you have a at ceiling:

WALL

Hang your fan by a standard downrod (included).

Standard Mounting

Support Structure

OPTION

If you have an angled ceiling:

1. You will need a longer downrod (sold separately).

2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately).

Use the three steps below to determine if your ceiling angle is greater than 34°

Angled Mounting

Standard Mounting Style

Ceiling

Outlet Box

(required)

Angled Mounting Style

Ceiling

Outlet Box

(required)

FOLD

on dotted line

34°

Guide Touches

BOTH Ceiling & Wall

You need ONLY

a Longer

Downrod

*most common

2 3

PLACE

against wall

Guide Touches

but NOT Ceiling

You need BOTH

a Longer

Downrod &

an Angled

Mounting Kit

SLIDE

toward ceiling

Wall

Use Standard Mounting

or Low-Prole Mounting

to hang the fan from a at ceiling.

Use Angled Mounting

to hang the fan from a

vaulted or angled ceiling.

Ceiling Bracket

Turn Power

OFF

For angled ceilings, point

opening toward peak.

www.CasablancaFanCo.com

1.888.227.21781.888.227.2178

Make sure all four bumpers are

still attached.

Refer to warning w.1 on pg. 2

If you are unable to do this,

call Technical Support at

1-888-277-2178.

Use wood screws

(included) when securing

to support structure with approved electrical outlet

box. Drill 9/64” pilot holes

in support structure to aid in securing ceiling bracket

with hardware found in

the hardware bag.

Use machine screws

(provided with outlet

box) when securing to

existing ceiling fan-rated

outlet box. Make sure

it is securely installed

and is acceptable for fan

support of 31.8 kg (70 lbs)

or less.

To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet

box associated with the wall switch location.

Downrod

www.CasablancaFanCo.com

1.888.227.2178

Standard Downrod

Option 1

Included

(pre-assembled)

Longer Downrod

for angled ceilings or

Option 2

high ceilings

skip to next page

If you need a different downrod length follow these steps:

Steps 1-5 to remove standard downrod pipe

1 2 3 4 5

Slide

678910

Sold Separately

Steps 6-10 to reassemble with new pipe

Downrod (continued)

www.CasablancaFanCo.com

1.888.227.2178

KEEP!

Remove the pre-installed

setscrew so that the downrod

can be inserted.

Slide the adapter cover over the

downrod, then hand tighten the

downrod (at least 4-5 full turns)

until it stops.

3/8”

8”

(not to scale)

The wires can be cut, but

leave at least 8” extending

from the top of the

downrod.

Tighten the setscrew

with pliers. DO NOT

HAND TIGHTEN.

8”

3/8”

If the setscrew is not tightened

securely, the fan may fall.

Downrod (continued)

www.CasablancaFanCo.com

1.888.227.2178

Lower the adapter cover until it

rests on top of the motor housing.

Put the wires and downrod

through the canopy. Let the

canopy sit loosely on top of

the fan.

DO NOT PICK THE FAN UP BY

THE CANOPY OR WIRES. Place

the downrod ball into the slot

in the ceiling bracket.

Wiring

Place the receiver on top of the downrod

Receiver

Note: To connect the wires, hold the bare metal leads together and place a wire connector over them,

then twist clockwise until tight.

www.CasablancaFanCo.com

1.888.227.2178

assembly as shown.

Refer to CAUTION c.1 on pg. 2

Using an orange wire connector

from the hardware bag:

Connect the 3 grounding wires (green, green/yellow stripe, or bare

copper) coming from the ceiling, downrod, and ceiling bracket.

Turn the splices upward and push them carefully back through the hanger bracket

into the outlet box. Spread the wires apart, with the grounded wires on one side of

the outlet box and the ungrounded wires on the other side of the outlet box.

green/yellow

stripe (grounding)

green/yellow stripe

green/yellow

stripe

Wiring (continued)

www.CasablancaFanCo.com

1.888.227.2178

Using the orange wire connectors from the remote control hardware bag:

• Connect the yellow wire from the receiver to the black wire

from the fan.

• Connect the blue wire from the receiver to the blue wire (or possibly black with white stripe

wire) from the fan.

Refer to CAUTION c.1 on pg. 2

yellow

black

blue

Using the orange wire connectors

black

(ungrounded)

white (grounded)

from the hardware bag:

• Connect the black (ungrounded)

wire from the ceiling to the black

wire from the receiver.

white

blue

• Connect the white (grounded) wire from the ceiling to both the white wire from the receiver and

black

the white wire from the fan.

Turn the splices upward and push them carefully back through the hanger bracket

into the outlet box. Spread the wires apart, with the grounded wires on one side of

the outlet box and the ungrounded wires on the other side of the outlet box.

Wall Control

Template

Drill Holes

Painter’s

Tape

Template

Screw

Cut-Out

Drywall

Anchors

Template

Drywall

www.CasablancaFanCo.com

Before

Cover Plate

After

1.888.227.2178

1. Tape the provided wall control

template with painter’s tape at

the desired installation area.

2. Drill holes inside the four corners of the template.

Note: Make sure the wall control template is level before

proceeding to the next step.

If you are using a outlet box for wall control installation, the wires coming from the wall

control must be grounded using the attached green wire. If not placed in an outlet box, cap

the green wire coming from the wall control with an included wire nut.

1. Using a 9/64 drill bit, drill a hole in each screw cut-out on the wall control template.

2. Using a hammer, tap a drywall

anchor found in the wall control hardware bag into each hole

until the drywall anchor is ush with the wall.

1. Using a drywall punch saw,

cut out the interior shape of the template using one of the four drilled corners as a

starting point.

2. Remove the template and the cut-out section of drywall.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

conditions: (1) this device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

1. Insert the wall control into the dry wall cut out.

2. Align the screw holes in the wall control with the drywall anchors.

3. Install the cover plate using

a Phillips Head screwdriver to secure the two cover plate screws found in the wall control hardware bag through the wall control and into the drywall

anchors.

Canopy

Screw

Holes

www.CasablancaFanCo.com

1.888.227.2178

Position the canopy so that, when

lifted into place, the canopy ts into

the hanging bracket as shown.

Lift the canopy into place so that

the screw holes are aligned.

Install the two canopy screws

found in the hardware bag.

Upper Switch Housing

Insert the third screw, found in

www.CasablancaFanCo.com

1.888.227.2178

Screw two switch housing assembly

screws, found in the hardware

bag, halfway into the mounting

plate on the bottom of the motor

housing. It does not matter which

two screw holes you choose.

Feed the two single-pin connectors

through the center hole of the upper

switch housing, then wrap the keyhole

slots around the screws and twist

counterclockwise.

the hardware bag, into place and

then tighten all three screws.

Make sure the upper switch housing is securely

attached to the mounting plate. Failure to properly

secure all 3 assembly screws could result in the switch

housing xture falling.

LED Assembly

Post

www.CasablancaFanCo.com

1.888.227.2178

Connect the single-pin connectors from

the LED assembly to the connectors

from the fan.

Screw two LED assembly screws, found

in the hardware bag. halfway into

two of the posts in the upper switch

housing. Push any excess wiring into

the switch housing, then wrap the

keyhole slots in the LED assembly

around the screws and twist clockwise.

Insert the third screw, found in

the hardware bag, into place and

then tighten all three screws.

Make sure the lower switch housing is securely attached to the

upper switch housing. Failure to properly secure all 3 assembly screws could result in the light xture falling.

Globe

WARNING

Tab

Notch

GLASS FALL HAZARD

To prevent SERIOUS INJURY or DEATH, make sure that glass is properly secured.

www.CasablancaFanCo.com

CONGRATULATIONS!

YOU’RE DONE!

1.888.227.2178

Position the notches in the outer rim of

the globe so they line up with the three tabs

on the inside rim of the LED assembly.

Carefully lift the globe up inside the LED

assembly as far as it will go, then rotate the

globe clockwise until it is held tightly in

place by the tabs.

NOTE: Check to ensure proper engagement

See next page for fan operation instructions.

Operation

Battery

Holder

Battery Door

Battery

Turn Power

www.CasablancaFanCo.com

1.888.227.2178

Before operating the wall control, press on the

battery door to eject it. Unscrew the battery

holder. Insert the battery, found in the control

hardware bag, with the positive (+) side facing

downward. Reinstall the battery holder and

reinsert the battery door into the wall control.

The remote transmitter is already paired

to the receiver and ready to use.

Note: If you would like to operate

multiple fans or multiple remotes,

or if your remote is not working,

please see the Troubleshooting

section at the end of this manual.

Operation (continued)

www.CasablancaFanCo.com

1.888.227.2178

Fan

(Low)

Speed

(High)

Lights Down

Reverse

Fan Speed

Lights Up

Fan Power

Battery

Holder

Quickly press the up or down arrow to turn the lights off

and on. Hold the up or down arrow to raise or dim the light

level. The reverse button changes the direction that the blades turn. The power button turns the fan off and on.

Dimming Mode: To enable dimming, you must rst set

your remote to Dimming Mode. To toggle Dimming

Mode on or off, hold down the Fan Power button while

pressing the Light Down arrow twice.

Reverse

Button

(a)

(b)

The reverse button on the wall

control changes the air ow

pattern. In warm weather, use

(a) downward air ow pattern.

In cold weather, use (b) upward

air ow pattern.

The Safe-Exit Program gives you

about thirty seconds of light when you turn the lights off to exit the room before the lights

go out. To use Safe-Exit:

• Press the fan power button off for at least three seconds to

initiate the Safe-Exit Mode.

• The lights will ash for visual conrmation.

• The lights will stay on 50% brightness for 20 seconds and then begin to dim. After a total

of 30 seconds, the lights will be

completely off.

Note: To connect the wires, hold the bare metal leads together and place a wire connector over them,

then twist clockwise until tight.

Maintenance & Cleaning

Turn Power

OFF

Be sure to turn off

power to the fan

before performing

any maintenance.

www.CasablancaFanCo.com

1.888.227.2178

Cleaning the fan - use soft brushes or cloths

to prevent scratching. Cleaning products may

damage the nishes.

Troubleshooting

www.CasablancaFanCo.com

1.888.227.2178

Fan doesn’t work

• Press a fan speed button (1–4).

• Check the circuit breaker to

ensure the power is turned on.

• Check the wall control battery.

• Make sure the blades spin freely.

• Turn off power from the circuit breaker, then loosen the canopy and check all the connections according to the wiring diagram

on pages 9–10.

Excessive wobbling

• Turn the power off, support the fan carefully, and check that the hanger ball is

properly seated.

• Use the provided balancing kit and instructions to balance

the fan.

Fan keeps spinning after power is turned off

• The blades may take a few minutes to come to a complete

stop. The powerful Casablanca

motor combined with the unique blade design on this fan allows for great air movement, but this may cause the blades to keep spinning for longer than expected after power is

turned off.

Remote does not work

• Make sure the battery is installed

correctly.

• Install a new battery.

• If the remote still does not work, you may need to pair

your remote. To prevent faulty operation, please disconnect power (at the wall switch, breaker, or fan) from all other ceiling fans within range while pairing. To pair: cycle power

to the fan by turning power off and back on at the wall switch

(or circuit breaker if necessary).

Within three minutes, press and hold both the Fan Off button and

the 4 button for four seconds to pair the remote. If applicable, the

fan will turn on and the lights

will ash and stay on to indicate successful pairing.

LED lights will not dim

• To enable dimming, you

must rst set your remote to Dimming Mode. To toggle Dimming Mode on or off, hold

down the Fan Off button while

pressing the Light Down arrow twice.

AUTHORIZED SERVICE

CENTERS

For the most updated list of Casablanca Authorized Service Centers, visit

www.CasablancaFanCo.com or call toll free 1-888-227-2178.

Troubleshooting (continued)

www.CasablancaFanCo.com

1.888.227.2178

Installing Multiple Fans with Independently Operating Remote Controls

To install multiple fans with independently operating remote controls, there is no need to perform any pairing procedures. Each set of receiver/transmitter is already paired. Simply

install each receiver into a fan and use the appropriate transmitter to operate each fan.

If your remote is not working, see the “Remote does not work” section on the previous page.

Installing Multiple Fans Operating on a Single Remote Control

To have multiple fans operated by a single remote control, you must pair the transmitter to each

additional receiver. The receiver that shipped with your fan is already paired to the transmitter.

Note: To prevent faulty operation, you MUST disconnect power (at the wall switch,

breaker, or fan) from all other ceiling fans within range while pairing each fan.

For each additional fan, ensure that a compatible receiver is installed. Disconnect power from all

other fans while pairing. To pair: cycle power to the fan by turning power off and back on at

the wall switch (or circuit breaker if necessary). Within three minutes, press and hold both

the Fan Off button and the 4 button for four seconds to pair the remote. If applicable, the

fan will turn on and the lights will ash and stay on to indicate successful pairing.

Installing One Fan Operating on Multiple Remote Controls

To have multiple remote controls operate one fan, you must pair each additional transmitter

to the receiver in the fan. The transmitter that shipped with your fan is already paired.

Note: To prevent faulty operation, please disconnect power (at the wall switch,

breaker, or fan) from all other ceiling fans within range while pairing.

For each additional transmitter, cycle power to the fan by turning power off and back on at

the wall switch (or circuit breaker if necessary). Within three minutes, press and hold both the Fan Off button and the 4 button for four seconds to pair the remote. If applicable, the

fan will turn on and the lights will ash and stay on to indicate successful pairing.

“Unpairing” Procedure for Faulty Operation of Remote Controls

If a transmitter is mistakenly operating a fan, you need to “unpair” the transmitter from that

fan’s receiver. The “unpairing” procedure is the same as the pairing procedure.

Note: To prevent faulty operation, you MUST disconnect power (at the wall switch,

breaker, or fan) from all other ceiling fans within range while “unpairing” a fan.

Disconnect power from all other fans while “unpairing.” Then, cycle power to the fan you

wish to “unpair” by turning power off and back on at the wall switch (or circuit breaker

if necessary). Within three minutes, press and hold both the Fan Off button and the 4

button for four seconds to “unpair” the remote. If applicable, the fan will turn off and the

lights will ash and turn off to indicate successful “unpairing.”

Casablanca Fan CFC2922 Owner Manual

Specifications and Main Features

Frequently Asked Questions

User Manual