Page 1
ATTACHMENT F.
- USER’S MANUAL
Page 2
TW-100
OWNER'S MANUAL
1
Page 3
Federal Communications Commission Requirements
Warning : Changes or modifications not expressly approved by
the party responsible for compliance with the FCC’S rules
could void the user's authority to operate the equipment.
THIS DEVICE COMPLIES WITH PARTS 15 OF FCC RULES
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS
(1)THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE,
AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE
RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE
UNDESIRED OPERATION.
2
Page 4
Content
1. Introduction - - - - - - - - - - - - - - - -
Page 4
2. Features- - - - - - - - - - - - - - - - - - - Page 5
3. Technical Specification - - - - - - - - - - - Page 6
4. Front Side - - - - - - - - - - - - - - - - Page 7
5. Charging Part - - - - - - - - - - - - - - - Page 11
6. Installation & Connection (Print, RS232)- - - Page 12
7. Method of Channel change - - - - - - - - - - Page 12
8. Set Mode - - - - - - - - - - - - - - - - - Page 13
9. Test Mode - - - - - - - - - - - - - - - - Page 14
10. Explanation for Error Message - - - - - - - - Page 16
3
Page 5
1. Introduction
Thanks for purchasing TW-100.
This g oo ds ha s hel d e xcell en t per forma nce and sp len did
properties through strike tests as well as devoting
ourselves under severe quality management.
Before using TW-100, It is recommended to read this
manual carefully and to use TW-100 completely.
Cautions
Do not press the keys hard, for it will operate with
soft touch.
Do not use ignitable materials for cleaning.
Avoid sudden temperature change.
Keep it in a dry place.
Do not use under the direct sunshine and on the dust
place for a long time.
Shift power switch to "ON" position, when you use it.
(Power switch is located on right-top corner.)
Shift power switch to "OFF" position, when you don't
use it for a long time.
4
Page 6
2. FEATURES OF TW-100
(1) Features
It is connected with CASTON(crane scale) by use of
wireless communication.
Simple operation.
WATCHDOG circuitry (system restoration)
Adapting high capacity rechargeable battery( DC7.2V,
720mA)
(2) Main Function
RS232C serial communication(standard)
Connectable with serial print.
Auto power off
Manual/Auto hold, peak hold
It is possible to set tare weight with keys
Storin g up to the 100 th of w eight , date a nd ti me, and
printing total weight.
Key operation by use of wireless communication
5
Page 7
3. TECHNICAL SPECIFICATION
Display LCD (5 digit)
Size of letter 12 mm (Height)
Display below zero
Status lamp Zero, Tare, Gross, Net, Hold, Stable, Print
Power
Power consumption 0.5 W
Operation
Frequency
Channel 32 channels
Channel interval
Generating
power(comm.)
Communication
Comm. speed 9600bps
Comm. distance Maximum (50M~100M)
TW-100 : Rechargeable DC Battery 7.2V 720mA
Charger: AC220V/60Hz
FSK(Frequency Shift Keying fsk)
displayed
“-”
-10 to +40
903Mhz < 918.5Mhz
500Khz
Maximum 10mW
6
Page 8
4. FRONT DISPLAY VIEW
Display lamp
Lamp: Weight is stable.
ZERO Lamp: Current weight is 0 kg.
GROSS Lamp: Current weight is GROSS.
NET Lamp: Current weight is NET.
TARE Lamp: TARE weight is stored.
PRINT Lamp: On printing.
HOLD Lamp: Lamp is on when weighing a moving object.
amp: Charged to 80%~100%.
L
Lamp: Charged to 50%~80%.
Lamp: Charged to 0%~50%.
Lamp: Discharged completely. It should be charged.
TX Lamp: Sending the data to CASTON
RX Lamp: Receiving the data from CASTON
(1)
7
Page 9
(2) KEYBOARD
0000
7777
4444
1111
list of weights
Displayed on the screen like this "Print", on pressing
PRT key.
Print format
NO 001 2000 kg
ID:20 00.03.01 12:12:12
NO 002 1000 kg
ID:16 00.03.01 12:22:12
NO 003 3000 kg
ID:35 00.03.01 12:32:12
------------------ TOTAL : 6000 kg
8888
5555
2222
Ι∆
Ι∆
Ι∆Ι∆
9999
6666
3333
ϒ
PRT
: Printing the
: When
ϒ
SET
setting a key tare value .
It is used to enter the set-mode.
you complete the set-mode or
8
Page 10
ϒ :
e
m
h
m
a
a
*
ϒ
ZERO
ϒ
It means the number “2” in the set-mode
TARE
It means the number "0" in the set-mode.
0
Return to 0(zero) weight
: When you enter test-mode.
1
It means the number "1" in the set-mode.
: It is used to TARE key in the normal status.
2
HOLD
ϒ
P.HOLD
GROSS
NET
K . T
ϒ
DATE
3
4
: Peak hold function in the normal status.
It means the number “4” in the set-mode
5
6
7
7
NUMBER
TARE
: Net weight function.
8
It means the number “6” in the set-mode
SET
ϒ
: Hold the w
It
ϒ
: Gross weig
It
ϒ
: When you w
It me
ϒ
: When you w
It me
How to enter
!
How to enter
!
8
DATE
NUMBER
"
9
SET
"
Page 11
9
ϒ
How to enter
!
ϒ
: When you want to change the time.
TIME
It means the number “9” in the set-mode
9
TIME
: Used to correct a mistake.
CLR
NUMBER
"
"
SET
ϒ
How to enter
!
ϒ
: Entering the product-id.
ID
ID
: storing the data of current weight, date, time and
SUM
NUMBER
"
SET
"
ID
(caution) 1. store up to the 100th-ID
2. When the weight is 0(zero),
'
ϒ
(χαυτιον) Ωηεν ψου δο νοτ υσε ιτ φορ α λονγ τιµε, τυρν οφφ τηε µαιν
: Power on/off key
ON
OFF
ποωερ σωιτχη
10
Page 12
5.RECHARGER
7
0
8
4
9
5
1
6
2
3
7
0
8
4
9
5
6
Insert a TW-100 to a charger and then plug-in as you
≤
can see in the picture.
Power lamp : Power lamp(red) is on, when you plug in
≤
Charger lamp : When TW-100 is charged completely, the
≤
lamp color
is changed from red to green
Charging time : It takes about 1~2 hours, but It
≤
depends on
discharging state.
11
Page 13
6.Print & RS232 port connection
Print & RS 232 port connection
≤
1) Connect rs232 port of the charger to print.
(RS 232port is located on the rear of the charger)
2)
ND-T102,ND-192,YS-360S print
ΡΞ∆ Γ Γ3 Τρανσµιτ ∆ατα
ΤΞ∆ Γ Γ2 Ρεχειϖε ∆ατα
ΓΝ∆ Γ Γ7 Σιγναλ Γρουνδ
9 pin port
(Female)
TW-100 charger RS-232C port Print port
7. Method to change channel
Open the case and separate RF Module PCB.
€
Perform a change channel as shown in the below figure
€
Channel Jump DIP
1
4
8
12
16
ΡΦ Μοδυλε ΠΧΒ
20
24
28
32
12
Page 14
8. SET MODE
(1) How to enter
Turn on the power with pressing the SET key
€
It will be displayed on the screen like this "SET".
(2) SET MENU
Initialize the stored weights
Set
value
(00-01)
""""
Number key : change number.
SET key : complete the setting
Setting
LCD SCREEN
F1-00
F1-01
Meaning
Storing
Initialize the weights
13
Page 15
9. TEST MODE
(1) How to enter
Turn on power with pressing the "ZERO" key
€
It will be displayed on the screen like this" TEST1".
(2) Key
ϒ SET key: moving to next menu
(3) Test menu
TEST 1 : LCD display test
TEST 2 : Received weight display test
TEST 3 : Key test
TEST 4 : serial communication test
TTEESSTT 1
1
Function
KEY
SET key:
to next
menu
TTEESSTT 2
Function
A
KEY LCD SCREEN DESCRIPTION
SET key:
TEST 2
condition.
to next
: LCD display test
LCD
tESt 1
888888
DESCRIPTION
TEST 1 procedure
TEST 1 operating
2
: Received weight display test(from
tESt 2
5500
TEST 2 condition.
Display the weight received
from CASTON
14
Page 16
TTEESSTT 3
3
Function
KEY LCD SCREEN DESCRIPTION
SET key:
to next menu
the other key :
test
< Key code >
KEY CODE KEY CODE KEY CODE
PRINT C0 SET A0 0 60
1C12A1361
4C25A2662
7C38A3
CLR C4 ID A4
TTEESSTT
Function
: Key test
tESt 3
1
Test 3 condition
Display the key number pressed
9
SUM
63
64
: Wireless communication
KEY LCD SCREEN DESCRIPTION
SET key:
to normal
mode
tESt 4
------
Test 4 condition
Checking transmit/receiving
15
Page 17
10 ERROR MESSAGE
rFErr
≤ Reason for error
When TW-100 can't communicate with CASTON in 5 seconds
Treatment
Turn off and then on.
nO-dA
≤ Reason for error
There is no data to print (When pressing PRINT key)
LO-u
≤ Reason for error
The weight is 0(zero)(When pressing SUM key)
mEm-F
≤ Reason for error
The number of stored data is over 100.
Treatment
After printing, start again
16
Loading...