Page 1
UH6000
UHF Wireless Microphone System
12340 World Trade Dr.
San Diego, CA. 92128
800-854-2235
carvin.com
Page 2
Page 3
CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
UH6000 RECEIVER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
HANDHELD MICROPHONE . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
BODYPACK TRANSMITTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
WARRANTY-SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
CONTENTS
Carvin’s Limited 90 Day Warranty
Carvin warrants to the original purchaser that your unit is free from any
defects in material or workmanship for a period of 90 days from the date
of purchase. If any such defect is discovered within the warranty period, Carvin will repair or replace the unit free of charge, subject to verification of the defect or malfunction upon delivery.
Important:
All items for service are to be return to Carvin (shipped prepaid), 12340
World Trade Dr., San Diego CA. 92128
This warranty does not apply to microphone capsules, nor to defects or
physical damage from abuse, neglect, accident, being dropped or
improper repair, alteration, or unreasonable use of the unit resulting in
cracked or broken cases or parts, or units damaged by excessive heat,
and does not apply to batteries or damage caused by leaking batteries.
This warranty does not cover finish or appearance items nor items damaged during shipping en route to Carvin for repair.
If factory service is required, please contact our service department at
800-854-2235 to obtain a return authorization number (RA). Make sure
the RA number is clearly marked on the outside of your package. If possible, please use your original packaging. Please include the Receiver,
Transmitter and Power Supply. You must also include a photocopy of
your proof of purchase or we cannot be responsible for repairs or
replacements. Carvin will not replace nor be responsible for any units
sent incomplete, without proper identification and return address or RA
number clearly marked on the package.
Any applicable implied warranties including warranties of merchantability and fitness are hereby limited to 90 days from the date of purchase.
Consequential or incidental damages resulting from a breach of any
applicable express or implied warranties are hereby excluded. This warranty is in lieu of all other agreements and warranties, general or special,
express or implied and no representative or person is authorized to
assume for us any other liability in connection with the sale or use of this
Carvin Wireless System.
Carvin wireless systems are type accepted under FCC rules, parts
90, 74 and 15.
This device complies with RSS-210 of Industry & Science Canada. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference; and (2) this device must accept any interference received, including interence that may cause undesired operation.
14 3
Page 4
Thank you for purchasing a Carvin UHF Diversity Wireless Microphone
System and congratulations on your choice. The UH6000 is the best performance and price value available in rackmount UHF wireless systems and
is loaded with features:
• Clear channel operation on the wide open, uncluttered UHF band for
interference-free performance in any application or locale.
• Carvin’s companding circuitry for an industry best 120dB
Dynamic Range, and the clearest, most natural sound available.
• Tone Squelch™ for locking out potential interference.
• Choice of transmitters:
• Bodypack with unique 3-way switch for selecting input type:
instrument (guitar, bass, etc.), headmic™ headworn mic, or lavalier mic.
• Handheld microphone with a powerful neodymium cartridge that
delivers unsurpassed audio, minimal handling noise and enhanced
feedback rejection.
• UH6000 receiver with DigiTRU Diversity™ for maximum range and dropout
protection, full LED indicators, both 1/4" unbalanced and XLR balanced
outputs, and special circuitry for noiseless transmitter ON/OFF switching.
INTRODUCTION SPECIFICATIONS
UH6000 RECEIVER
Frequency Response
50 Hz - 15 KHz, +/- 3 dB
Dynamic Range
120 dB
Total Harmonic Distortion
< 0.6%
RF Carrier Frequency Range
UHF, choice of single frequencies from
794-820 MHz
Frequency Stability
+/- 0.005% crystal controlled
Modulation
FM (F3E), +/- 20 KHz
Operating Range
Up to 250 feet typical (depending on
site conditions)–up to 500+ feet lineof-sight
Reception Mode
DigiTRU Diversity™ (Dual Antenna)
Squelch
Tone Key (32.768 KHz), External
Control
Controls
Power ON/OFF, Volume Control, Level
Low/Hi Switch, Squelch (Mute) Adjust
Connectors
DC in, 1/4" (6.3 mm) unbalanced
phone jack (750 mV/5K Ohm), XLR
balanced output (60 mV/600 Ohm), A
& B BNC antenna jacks, fuse
LED Indicators
Power ON, Diversity A/B, RF LEVEL
and AF LEVEL (5 segment) displays
Unwanted Signal Rejection
60dB image and spurious
Power Requirements
DC 12-15V @ 300 mA, AC/DC adapter
included
Dimensions
16" x 6.5" x 1.73"
(40.6 x 16.5 x 4.4 cm)
Fuse
20mm glass type, 250V, 500mA
Weight
3.93 lb (1.8 Kg)
TRANSMITTERS
Audio Inputs
Bodypack: 3.5mm locking
mini-jack 3-way select switch
for inputs: instrument,
headworn mic, or lavalier mic
Handheld Mic: Integral
neodymium dynamic cartridge
Controls
Bodypack: OFF/STANDBY/ON,
INSTRUMENT/HEADWORN
MIC/LAV MIC, INPUT LEVEL
Handheld Mic:
OFF/STANDBY/ON
LED Indicator
Unit “ON” (single flash), Low Battery
Alert (steady)
RF Power Out
50mW nominal (maximum allowed
by FCC)
Harmonic & Spurious Emissions
< -50 dB
Battery
9V Alkaline
Battery Life
8-10 Hours (35mA draw typical)
Dimensions
Bodypack: 4.2" x 2.5"x .88"
(10.7 x 6.4 x 2.2 cm)
Handheld Mic: 9.5"x 1.37"
(24.1 x 3.48cm)
Weight
Bodypack: 3 oz (84g)
Handheld Mic: 7.5 oz (210g)
Specifications subject to change for
product improvement purposes
4 13
Page 5
1. Rackmounting the Receiver
The UH6000 is supplied with RACK EARS (17) which can be attached with the screws
provided on the front of the side panels to enable rackmounting the receiver. (Note: Do
not mount the receiver in a rack directly above an amplifier or other source of high heat.
Always ensure adequate air flow and heat dissipation in any rack configuration.
2. Powering the Receiver
Plug the 12V AC/DC ADAPTER (15) provided into the DC INPUT JACK (11) on the back of
the receiver. Then plug the power supply into an AC outlet. (Note: Any DC source with
300mA capability can also be used.) Press the POWER SWITCH (8) once to turn on the
receiver. The POWER ON LED (7) will now light and the receiver is operational.
3. Antennas
The UH6000 receiver is supplied with two detachable ANTENNAS (16). These can be
either rear-mounted (standard) on the BNC ANTENNA JACKS PROVIDED (9) or mounted
on the front (when rackmounting the receiver) with the optional FR-2 FRONT-ANTENNA
RACKMOUNT KIT (18). To use the FR-2 kit, attach these special rack ears to the front of
the side panels of the receiver, as with the standard rack ears provided. Attach the two
short cables supplied between each ANTENNA JACK (9) and the jacks on the back of the
FR-2 RACK EARS (18). This will provide a connection between the FR-2 front-panel antenna jacks and the antenna jacks of the receiver. Connect the antennas to either these FR-2
jacks or the antenna jacks on the back of the receiver directly if not using the optional FR-
2. Extend the TELESCOPIC ANTENNAS (16) fully to obtain maximum range. Optimal
antenna position is 45 degrees from the receiver (at 90 degrees from each other).
4. Squelch Adjustment
In normal operation, the SQUELCH CONTROL (2) should be set fully clockwise to the factory preset RF level ”10”. However, in areas of high RF activity, the squelch (or mute, as it
is sometimes called) may need to be adjusted to compensate for the adverse conditions in
a particular location. If, with the transmitter off, the receiver’s A and/or B DIVERSITY LED
INDICATORS (3) and/or one or more LEDs of the 5 LED RF LEVEL (4) display flicker or
stay on, the squelch control should be turned counterclockwise until the LEDs extinguish.
When the squelch is properly adjusted, the A and/or B LEDs or the RF LEVEL LED displays will only light when the system transmitter is turned on. Turning the squelch control too far counter clockwise will reduce the range, but yield a quieter squelch (mute)
function. During operation, especially at ranges greater than 75 feet, one or the other of
the A or B LEDs may extinguish briefly. This is normal–the unit’s DigiTRU Diversity™
reception ensures that the received audio will not be interrupted. When both the A/B
Diversity LEDs and the 5 LED RF LEVEL display extinguish, the transmitter is out of range
for that given location, and the user should move closer to the receiver to re-establish the
radio link.
UH6000 RECIEVER
24. BATTERY COMPARTMENT
25. 9V ALKALINE BATTERY
26. INPUT SELECTOR SWITCH
27. 3.5mm LOCKING JACK
28. INSTRUMENT CORD
29. HEADWORN MIC
30. LAVALIER MIC
31. OFF/STANDBY/ON SWITCH
32. BATTERY INDICATOR LED
33. INPUT LEVEL CONTROL
34. CLIP
12
5
24
34
25
24
26
Page 6
5. Connecting the Audio Output
The URR-10 receiver provides both a fixed mic level BALANCED AUDIO OUTPUT XLR (14)
and an adjustable line level UNBALANCED AUDIO OUTPUT 1/4" JACK (13). The level from
the UNBALANCED OUTPUT is controlled by the front panel VOLUME CONTROL (6) and the
rear panel LEVEL LOW/HI SWITCH (12). This switch adjusts the maximum volume of the
level range controlled by the VOLUME CONTROL. In the “LOW” position, the level of the
signal from the UNBALANCED OUTPUT, with the VOLUME CONTROL set to “10”, is about
10% of the maximum volume available with the “HI” position. Proper use of the LOW/HI
SWITCH enables better control of the UNBALANCED OUTPUT volume.
(Note: As when making any connection, make sure the amplifier or mixing board volume is at the minimum level before plugging in the receiver to avoid possible sound system damage.)
Instrument Connection (using the Body Pack Transmitter in the “instrument” setting)
Insert an audio cord with a 1/4" mono phone plug in the UNBALANCED OUTPUT JACK (13)
on the rear panel of the receiver. Plug the other end of the cord into an amplifier, effects, or
mixing board. With the LEVEL LOW/HI SWITCH (12) set to HI, adjust the VOLUME CONTROL (6) on the receiver clockwise to about 3/4 rotation, until the volume level is comfortable for your application. This setting is roughly equivalent to a direct instrument cord connection. Turning the volume up to “10” will provide 4dB gain over a cord.
Microphone Connection (using the Body Pack Transmitter with either a headworn or
lavalier microphone or the handheld microphone transmitter)
For microphone use, either the BALANCED MIC AUDIO OUTPUT XLR (14) or the 1/4" line
level UNBALANCED OUTPUT (13) can be used. The XLR output is set at a non-adjustable
microphone level, similar to hardwired mic levels. Plug an XLR connector into the XLR output jack on the rear of the unit and plug the other end into your amplifier or mixing board.
Make sure the phantom power on your mixing board is turned off and the volume is turned
down when making connections. For your convenience, the XLR output level is preset at
the factory and is not adjustable with the receiver volume control.
To use the 1/4" UNBALANCED OUTPUT JACK (13), follow the instructions for the
Instrument Connection (above), except start with the LEVEL LOW/HI SWITCH set to LOW
and the receiver volume at 1/2 MAX and adjust both the switch and the volume control until
the volume level is optimal. If the volume control is set too high, you may overload your
mixer or amp.
The receiver is equipped with an AF LEVEL LED DISPLAY (5) which indicates the level of
the received audio from the transmitter. There are 4 green and 1 red LED in this display and
in normal operation they will go on and off with the changing signal level. If the top (red)
LED stays on continuously, decrease the volume to the transmitter or overload distortion
may result.
For optimum performance, an INPUT LEVEL CONTROL (32) is provided. Adjust the gain
by turning the control with your thumb. For lavalier mic use, it is recommended that the
level be set at about 2/3 maximum. For headworn mic use, it may be advisable to turn the
gain down somewhat, depending on the volume evels expected. In either application,
experiment and set for maximum possible gain without audible distortion on the high level
peaks. (Note: Turning down the gain too much can compromise the signal-to-noise and is
not recommended.)
The AF LEVEL DISPLAY (5) on the receiver will light up to 5 LED indicators for all input
signals. Occasional flickering on and off during use of the top red LED is normal, but if the
red LED stays lit continuously, turn down the INPUT LEVEL CONTROL (33) on the Body
Pack Transmitter or noticeable distortion may result.
6 11
27
33
28
30
31
32
29
Page 7
10
7
The AF LEVEL LED DISPLAY (5) on the receiver will light up to 5 LEDs for all input signals.
Occasional flickering on and off during use of the top red LED indicator in this display is
normal, however if the red LED stays on continuously, turn down the instrument volume or
the INPUT LEVEL CONTROL (33) on the transmitter, or noticeable distortion may result.
(Note: Scratchy noises can sometimes occur when some electric guitars with dirty pots or
connections are used with any wireless system. For this reason, the supplied INSTRUMENT
CORD (28) has a factory installed capacitor inside the 1/4" plug. This capacitor provides
first order filtering of the RF signal from the cord into the guitar and eliminates virtually all
scratchy noises. Should your equipment still give you scratchy noises, we suggest these
steps to eliminate them:
1) Make sure all guitar volume and tone pots are clean and all contacts are solid–this is
very important.
2) Provide extra filtering with a 47pf capacitor soldered across the hot to ground terminals
of the guitar’s volume and tone pots.)
6.Microphone Use (with either a lavalier or headworn microphone)
Secure the connection from the LAVALIER (30) or HEADWORN MIC CORD (29) by turning
the slip ring on the plug into the transmitter clockwise to thread it on to the jack. To
unplug, reverse the process. To use the lavalier mic, attach it at chest level. Do not place it
too close to the mouth–a distance of about six inches usually works best. To use the headworn mic, place it on the head and adjust the boom so that the mic is about one inch to the
side of the front of the mouth. When ready to speak, slide the OFF/STANDBY/ON SWITCH
(31) to the ON position. Adjust the volume of the receiver as per the Audio Output
Microphone Connection section of the above receiver instructions.
[Note: Observe care in
selecting P.A. volume, transmitter location and speaker placement so that acoustic feedback (howling and screeching) will be avoided. Please also note the pickup pattern characteristics of the microphone selected. Omnidirectional mics pick up sound equally from all
directions and are prone to feedback if not used carefully. Unidirectional mics are more
resistant to feedback, but pick up sound sources best that are directly in front of the mic.
Also, mics that are farther from the sound source, such a lavaliers, require more acoustic
gain and thus are also more prone to feedback than close-source mics such as handheld or
headworn models that are used close to the mouth].
1. FRONT PANEL
2. SQUELCH CONTROL
3. A/B DIVERSITY LED INDICATORS
4. RF LEVEL LED INDICATORS
5. AF LEVEL LED INDICATORS
6. VOLUME CONTROL
7. POWER ON LED
8. POWER SWITCH
9. BNC ANTENNA JACK
10. FUSE
11. DC INPUT JACK
12. LEVEL LOW/HI SWITCH
13. UNBALANCED AUDIO OUT
14. BALANCED AUDIO OUT
15. 12-15 VDC ADAPTER
16. TELESCOPING ANTENNAS
17. STANDARD RACK EARS
18. FR-2 FRONT-ANTENNA RACK KIT
FRONT PANEL
REAR PANEL
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
9
17
18
16
Page 8
1. Unscrew the BATTERY COMPARTMENT COVER (19) and remove, exposing the BAT-
TERY HOLDER (20). Insert a fresh 9V ALKALINE BATTERY (21), observing the correct polarity as marked, and screw the cover back on to the microphone. Make sure
the cover is screwed on completely. A fresh alkaline battery can last up to 10 hours in
use, but in order to ensure optimum performance, it is recommended that you
replace the battery after every 7-8 hours of use.
2. Turn on the UH-10 by sliding the OFF/STANDBY/ON SWITCH (22) to the STANDBY
position (transmitter on, audio muted) or the ON position (transmitter and audio both
on). The BATTERY INDICATOR LED (23) will give a single quick flash, indicating
usable battery strength. In the case of a dead or low battery, the LED will either not
go on at all or will stay on continuously, indicating that the battery should be replaced
with a fresh one. To preserve battery life, turn the transmitter off when not in use.
3. The microphone is now ready to use. The A and/or B DIVERSITY LED INDICATORS
(3) and most or all of the RF LEVEL DISPLAY LEDs (4) on the receiver should now
be lit, indicating a received signal from the transmitter. When ready to speak, slide
the transmitter switch to the ON position. Adjust the volume of the receiver as per the
Audio Output Microphone Connection section of the above URR-10 receiver instructions.
[Note: Observe care in selecting P.A. volume, transmitter location and speaker
placement so that acoustic feedback (howling or screeching) will be avoided.]
1. Slide open the hinged BATTERY COMPARTMENT (24) and insert a fresh 9V ALKALINE
BATTERY (25), observing the correct polarity. A fresh alkaline battery can last up to 10
hours in use, but in order to ensure optimum performance, it is recommended that
the battery be replaced after 7-8 hours of use.
2. The Bodypack Transmitter is equipped with an INPUT SELECTOR SWITCH (26) in the
battery compartment for selecting the type of audio input you will be supplying to the
transmitter. Select from the choice of three positions: INSTRUMENT (for guitar, bass,
etc.)/ HEADWORN MIC/ LAVALIER MIC.
3. The Bodypack Transmitter is provided with a 3.5 mm LOCKING JACK (27) for con-
necting the audio input selected. Connect either the INSTRUMENT CORD (28) or the
HEADWORN MIC (29) or LAVALIER MIC CORD (30) as desired, according to the input
selected.
(Note: Use only the input audio source as per the input selected with the
AUDIO INPUT SELECTOR SWITCH or the audio will not be optimal–a muddy or distorted sound may result.) To secure the connection, turn the slip ring on the plug
clockwise to thread it on the jack. To unplug, reverse the process. Slip the transmitter
into a pocket or use CLIP (34) to attach it to your clothes or instrument strap (if using
as an instrument transmitter).
4. Turn on the Bodypack Transmitter by sliding the OFF/STANDBY/ON SWITCH (31) to
the STANDBY position (transmitter on, audio muted) or the ON position (transmitter
and audio both on). The BATTERY INDICATOR LED (32) will give a single quick flash,
indicating usable battery strength. In the case of a dead or low battery, the LED either
will not go on at all or will stay on continuously, indicating that the battery should be
replaced with a fresh one. To preserve battery life, turn the transmitter off when not
in use. The transmitter is now ready to use. The A and/or B DIVERSITY LED INDICA-
TORS (3) and most or all of the RF DISPLAY LEDs (4) on the receiver should now be
lit, indicating a received signal from the transmitter.
5. Instrument Use
Plug the 1/4" phone plug from the INSTRUMENT CORD (28) into the instrument. As
the cord to the instrument also serves as the antenna, be sure to extend it fully for
maximum range. Rolling up or shortening the cord may reduce the effective operating
range. When ready to play, slide the audio OFF/STANDBY/ON SWITCH (31) to the ON
position. Adjust the volume of the receiver as per the Audio Output Instrument
Connections section of the above receiver instructions. For optimum performance, an
INPUT LEVEL CONTROL (33) is provided on the top panel of the Bodypack transmittert. Adjust the gain by turning the control with your thumb. For instrument use, it is
recommended that this control be turned to maximum gain. However, for ultra highgain instrument sources such as active bass pickups or even extra hot guitar pickups,
turning the level down slightly will create a cleaner sound.
(Note: Turning down the
input gain too much can compromise the signal-to-noise ratio and is not recommended. Set for the maximum possible gain and headroom without noticeable distortion on
the high level peaks).
HANDHELD MICROPHONE
BODYPACK TRANSMITTER
19. BATTERY COMPARTMENT COVER
20. BATTERY HOLDER
21. 9V ALKALINE BATTERY
22. OFF/STANDBY/ON SWITCH
23. BATTERY INDICATOR LED
21
20
19
23
22
20
8
9
Loading...