CARVIN TRx3010A, TRx3018A User Manual
TRx3010A, TRx3018A ACTIVE SUBWOOFERS USER MANUAL
TRx3010A TRx3018A
MADE IN
USA
The TRx3010A and TRx3018A are active 2500W, X-Drive™ DSP
processed subwoofer systems with an additional amplifier output to
power external cabinets. The TRx3010A uses dual long-excursion
TSUB10 woofers with 2.5-inch voice coils. The TRx3018A uses a
cast frame TS18B woofer with a 23mm, inside/outside wound, 4-inch
voice coil. Optimized presets for several Carvin cabinets are factory
programmed for simple connect, select and play.
ACTIVE 2500W SYSTEM
The 2500W active X-Drive™ DSP processed module provides a
1500W bridged amplifier for the internal woofers and an additional
1000W amplifier output for external main cabinets. The internal
X-Drive™ DSP processing maximizes performance output and protection using up to 48dB/oct crossover filters, parametric EQ, alignment
delay and limiters. Turn on the Enhanced Bass and the ultra low end
will come alive, lowering the cabinet’s frequency range by another
15Hz and boosting the 35-50Hz response. The DSP will control the
output to keep this added response within the limits of the speaker.
CONNECT, SELECT AND PLAY
The external amplifier output is ideal for powering two TRx3903’s
for a full range TRC-A system or up to two TRx2115’s, TRx3210’s,
TRx12N’s, SCx1115’s or any top main cabinets down to 4 ohm. The
internal X-Drive™ DSP has been set up to maximize performance
output of the preset Carvin cabinets. Don’t have a Carvin main or
not finding your cabinet? Simply go to the “Variable X-Over” preset,
select the crossover frequency and you are ready to go. Don’t need to
power a top cabinet? Go to the “Sub only” preset, select the crossover
frequency for the sub and you are ready to go.
CORNERSTONE OF THE TRC-A COLUMN SYSTEMS
The TRC-A (active) column systems are compact powerful live
sound systems, with the TRx3010A or TRx3018A as the cornerstone
for system amplification and DSP processing. The TRx3903 columns
complete the system’s mid to high frequency coverage to produce wide
and clear sound reinforcement. Each TRx3010A or TRx3018A can drive
two TRx3903 column elements. The internal X-Drive™ DSP processor maximizes performance output, so all you need to do is select the
TRx3903 preset, plug in the speakers and play. These systems are
small enough to fit in a midsize hatchback, but large enough to fill a
large banquet hall with a full band.
FLEXIBLE AND FAST SYSTEM SETUP
The TRx3010A and TRx3018A feature foot locating holes on top for
stacking another TRx3010A (or) TRx3018A, and allow stacking up
to 4 TRx3210 line array elements without hardware. The TRx3010A
can be used flat, or on it’s side for a smaller footprint. The top or side
TRx3010A pole mounts and center TRx3018A pole mount can suspend
two stacked TRx3903’s or any standard 1-3/8th pole mount equipped
cabinet. Two additional pole mounts on the TRx3018A match the 16”
spaced dual pole system for suspending two TRx3210’s, or allow
mounting two speakers side by side for wider coverage.
RECEIVING INSPECTION—read before getting started
INSPECT YOUR UNIT FOR DAMAGE, which may have occurred during shipping. If damage is
found, please notify the shipping company and CARVIN immediately.
SAVE THE CARTON & ALL PACKING MATERIALS. In the event you have to re-ship your unit, always
use the original carton and packing material. This will provide the best possible protection during shipment. CARVIN and the shipping company are not liable for any damage caused by improper packing.
SAVE YOUR INVOICE. It will be required for warranty service if needed in the future.
SHIPMENT SHORTAGE. If you find items missing, they may have been shipped separately. Please
allow several days for the rest of your order to arrive before inquiring.
RECORD THE SERIAL NUMBER on the enclosed warranty card for your records. Keep your
portion of the card and return the portion with your name and comments to us.
SPECIFICATIONS: TRx3010A, TRx3018A
System Type: Active, 2500W X-Drive™ processed
TRx3010A: Dual 10-inch sub, bass reflex
TRx3018A: 18-inch sub, bass-reflex
Freq. Response: TRx3010A: 40 Hz – 1.5kHz (-10dB), 43 Hz – 1kHz (-3dB)
TRx3018A: 32 Hz – 1.5kHz (-10dB), 38 Hz – 1kHz (-3dB)
Bass Enhance mode: 15Hz < normal
Coverage Pattern: Omni - Cardioid in 8x arrays
Crossover Frequency: Active DSP Preset, or 58-160 Hz @24dB/oct.
Power: 3200W 2 cycle pulse peak
2500W 20ms burst (1500W /1000W external)
1875W RMS (1250W, 625W external)
Input Sensitivity: 1.0, 1.2, 1.4, or 2.0 Vrms settings
Maximum Input signal: +12dBu
Maximum SPL: TRx3010A: 128dB peak, TRx3018A: 131dB peak
Drivers: (2x) 10-inch, 2.5-inch VC 18-inch, 4-inch VC
Enclosure: 13-Ply Russian Baltic Birch
Mounting: TRx3010A: Foot receivers for TRx3210, TRx3010A,
top and side 1-3/8-inch Pole Cups
TRx3018A: Foot receivers for TRx3210, TRx3018A,
(3x) 1-3/8-inch Pole Cups
Finish: Black DuraTec™
Transport: 2 Recessed Handles
Grill: Black powder coated steel
Acoustically Transparent Foam Backing
Connectors: Signal In/Thru: XLR female/XLR male
External Speaker: 4 pin twist-lock
Remote Level/Mute: Terminal block
AC IN/OUT: Locking IEC receptacles
Dimensions TRx3010A: 15 x 23.5 x 18 in. (381 x 597 x 458 mm)
TRx3018A: 23.5 x 23.5 x 23.5 in. (597 x 597 x 597 mm)
Net Wt: TRx3010A: 57 lb (26 kg)
TRx3018A: 75 lb (37 kg)
Origin: USA
12340 WORLD TRADE DRIVE SAN DIEGO, CA 92128
800-854-2235 CARVINAUDIO.COM
CONTROL PANEL FEATURES
1 2 5
12 3 4 6
1. POWER SWITCH (reset)
Push the upper portion of the power switch to turn the system on. If
the blue POWER indicator is on but there is no sound or the Protect
LED is on, reset, turn the power off for 10 seconds and then turn it
back on. If the problem persists, check for; a) lack of Input signal,
b) external speaker impedance being too low for the amp, c) bad
speaker cable, d) damaged speaker, or e) blocked fan intake.
2. POWER LED
The POWER LED indicates the unit is turned on and functioning
properly.
3. SIGNAL LED
The SIGNAL LED indicates there is a signal present at the INPUT
XLR.
4. LIMIT LED
The LIMIT LED indicates maximum output of the system is being
reached. A flashing LIMIT LED is acceptable, the DSP will reduce
peaks to prevent amp clipping. If the LIMIT LED is continuously ON,
reduce the level going in to the INPUT XLR. As with any system,
reduce the volume if distortion is heard.
5. DIGITAL DISPLAY
The bright green LED DIGITAL DISPLAY will display various information about the system and its settings. When you first turn on the unit,
the display will indicate which preset is loaded. To change settings
use the UP/DOWN (SET) and LEFT/RIGHT buttons.
6. SETTING BUTTONS (SET)
Use the UP and DOWN (SET) buttons to load different presets for
external speaker connections. The LEFT and RIGHT buttons will
allow editing of more advanced settings, which are explained in the
SETTINGS MENU section of this manual. There are only a few to
select from.
7. INPUT/THRU XLR CONNECTORS
Connect the INPUT XLR to a signal source such as the output of
a mixer. The THRU XLR can be connected to more TRx3010A’s,
TRx3018A’s or other units.
8. REMOTE LEVEL (MUTE) CONNECTOR
This is a terminal block connector with 5 volt control of volume,
typically used in permanent installations. Short the CTL and GND
pins to MUTE.
9. USB PORT
The USB port is for updating system firmware such as additional
Carvin Audio speaker presets for Carvin Audio speakers connected
to the SATELLITE SPEAKER output.
8
9101113
7
10. PROTECT LED
The PROTECT LED indicates one of the protection circuits has
activated and no sound will be heard from the amp. To reset the
amp, turn the power off for about 10 seconds, then turn it back ON.
If the PROTECT LED stays lit for more than 5 seconds, check your
SPEAKER OUTPUT cable connnections, speaker impedance or a
blocked fan intake.
11. SATELLITE SPEAKER OUTPUT
The SATELLITE SPEAKER output is a Twist-Lock connector for
powering external speakers. Presets for several Carvin Audio speakers
are pre-programmed. If there is no preset for your speaker, manual
settings are available. Speakers can be chained together so long as
the total impedance does not go below 4 ohms. If you go below the
minimum speaker load, the amp may shut off or the red PROTECT
LED may light. To reset the protection circuit, turn off the POWER
switch and connect the recommended load.
12. FAN INTAKE / EXHAUST VENTS
The power module features a variable speed fan, which runs silent
at low speeds. Make sure the fan intake and exhaust vents are free
from blockage at all times.
13. AC IN / AC OUT POWER JACKS & FUSE
Be sure to plug into the proper voltage using AC IN jack. A detachable locking power cord is supplied (for European 230V use a CEE-7
plug cord set). Plug the cord into a grounded 3 prong power source.
No attempt should ever be made to use the amp without the ground
connected.
The AC OUT connector can be used to power one or two units such
as another TRx3010A/TRx3018A, a powered speaker, or any device
with 10A or less rating.
The FUSE is located internally near the AC input. To check or
replace, first remove the power cord and then remove the amp
module from the speaker enclosure and then remove the front panel
to access the fuse. The fuse type is a 250V Slow Blow rated at 15A.
A locking AC cord (Carvin Audio part# 120V16L7, 120V model) is
supplied with the amp. However, a standard AC cord can be used.
To detach the cord from the amp, press the release lever on the
underside of the cord near the amp.
PRESS TO
LOCKING AC CORD
120V16L7
RELEASE
Loading...