CARVIN ENGINEERING DATA OPERATING MANUAL
12340 World Trade Drive, San Diego, CA 92128
(800) 854-2235
carvin.com
For your records, you may wish to record the following information.
Serial No._____________________ Invoice Date_______________
SX300C
RECEIVING INSPECTION—read before getting started
INSPECT YOUR AMP FOR ANY DAMAGE which may have occurred during shipping. If any damage is found, please notify the shipping company and CARVIN
immediately.
SAVE THE CARTON & ALL PACKING MATERIALS. In the event you have to re-ship
your unit, always use the original carton and packing material. This will provide the
best possible protection during shipment. CARVIN and the shipping company are not
liable for any damage caused by improper packing.
SAVE YOUR INVOICE. It will be required for warranty service if needed in the
future.
SHIPMENT SHORTAGE. If you find items missing, they may have been shipped
separately. Please allow several days for the rest of your order to arrive before
inquiring.
RECORD THE SERIAL NUMBER on the enclosed warranty card or below on this
manual for your records. Keep your portion of the card and return the portion
with your name and comments to us.
SX300C, SX300H, SX300R
GUITAR AMPS
SX SERIES SPECIFICATIONS:
Speakers: SX300C Two
CCeelleessttiioonn SSEEVVEENNTTYY 8800
100w 8Ω speakers
RMS Power: SX300C/SX300H 100 watts @ 4, 8, 16Ω
Output Impedance: 4-16 ohms switchable
Power Amp: THD: Less than 1%
Input Impedance: 100k ohms
Channels: 3—switching
Tone Controls:
Ch 1 and 2 BASS: 80Hz
MID: 600Hz
TREBLE: 8k Hz
PRESENCE: 11k Hz
Ch 3 BASS: 90Hz
MID: 575Hz
TREBLE: 9k Hz
PRESENCE: 8-11k Hz
Ch 1 + 2 Sensitivity: 1mV for clipping, dynamic range 72dB
Ch 3 Sensitivity: 75mV for full output
Line Out: 1.5 VAC @ full power
Power: 120V or 240V model
Fuse: 5 amp 250V internal
Size: SX300C: 26W x 10.25D x 17.5”H
SX300H: 24.5W x 9.5D x 10.5”H
SX300R: 19W x 6D x 1.75”H
Cabinet: Plywood–no particle board
Net Weight: SX300C: 44 lbs, SX300H: 24 lbs, SX300R: 5 lbs
Warranty: One Year
Options: FS44 footswitch,
CV3212 cover SX300
CV3200 cover SX300H
VE212 extension cabinet, two GT12 200w 8Ω speakers
76-10203 C 07/05
c
SX SERIES
Classic Tube Emulation, awesome digital effects, rich black vinyl
covering and the brass red jewel light continue to make the AMERICAN MADE SX
Series one of the hottest amps on the market today!
EMULATION OR MODELING?
Unlike other “modeling” amps, the SX
doesn’t just copy the sounds of other amplifiers – it actually emulates 12AX7 tube
circuitry. The SX waveforms successfully “emulates” real tube waveforms that
breathe and express warmth from a mild soft-clip to a full power soaked sustain.
Pro players and industry gurus have stated that the SX Tube Emulator actually
sounds better than many tube amps!
THREE CHANNELS
– CH1 LEAD with high gain switch, CH2 LEAD with
BLUES switch and CH3 CLEAN. Each channel has its own independent volume
control for setting up equal levels quickly and easily.
ACTIVE TONE CONTROLS
All models feature BASS, MID, TREBLE con-
trols and a PRESENCE switch on all channels.
24-BIT EFFECTS
Once you have your tone, add in just the right amount of
lush REVERBS, rich CHORUSES, thick textured FLANGING or pristine ECHOES
using fully adjustable parameters for damping, decay, depth, speed, time and regeneration–up to 256 24-BIT effects. There is also a second digital processor dedicated to creating a lush, concert-hall reverb at the push of a button.
POWER
The SX300C and SX300H feature a full 100 watts RMS. The SX300C
features two 12” heavy-duty 100w Celestion SEVENTY 80 speakers that provide
awesome guitar reproduction – from clean to blues to scream’n metal. The
SX300H head can be paired with either a 4x12 half stack or 8x12 full stack. The
SX300R rackmount pre amp can be paired with the amp of your choice.
REAR PANEL CONNECTIONS
All back panels feature a voiced LINE OUT
for recording or running a slave amp, HEADPHONE jack, EXTENSION SPEAKER jack
and a FOOT SWITCH jack for the optional FS44 for remotely changing channels and
turning on/off the effects, (The extra dedicated reverb on the SX300C, SX300H and
SX300R is controlled by a front panel switch.) The SX300C & SX300H also adds
SEND/RETURN jacks for your own external effects. A 4, 8, 16Ω impedance switch
is featured for optimizing the amp for the extension speakers.
RUGGED CONSTRUCTION
SMT surface mount electronics ensure consistent, reliable performance, which is impervious to bumps and vibrations.
Strong, lightweight plywood cabinet (not particle board), aluminum chassis, steel
grille and corners deliver one of the lightest, yet most rugged amps available.
SX300R
SX300H
FEATURES
CELESTION
SPEAKERS
VOLUME DRIVE TREBLE
TREBL
VOLUME DRIVE MID
MIDBASS
1
PRESEN
INPUT
1
0
10
9
8
7
6
5
4
3
2
1
0
1
0
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
0
6
5
4
3
2
PRESENCE
HI GAIN
SEL
BASS
2
SEL
BLUES
GETTING STARTED QUICKLY
If you are like most players, you probably want to plug in your new amp and get started playing right away. You can read the rest of the manual later to learn the finer points
of operating your amp. In order to get started you will need your SX AMP, a 120 or 230
AC grounded power outlet, your instrument, and a standard guitar cord. With the amp
turned off, you may now plug it into the proper AC voltage.
Now turn all the volume and overdrive controls off and set tone controls at their mid center
position. If you have purchased the FS44 foot switch, plug it into the rear foot switch jack
for switching the channels and effects.
Now, turn the POWER SWITCH ON. Gradually raise
the volume and overdrive controls. Check the BLUES SWITCH and HI GAIN switch setting
before adjusting the tone controls.
FRONT PANEL
1. INPUT
Connect a 1/4” guitar cable to this input. Use a professional quality 1/4” plug shielded
guitar cord (Carvin SH25) no longer than 25 feet. A longer cable will reduce the overall
treble response from your pickups.
2. CHANNEL SELECT
Select the desired channel using front panel switches or FS44 foot switch at any time.
The LED’s will let you see which channel is functioning. Use CH1 for overdrive/lead, CH2
for lead/blues, and CH3 for clean playing.
CHANNEL 1 AND 2 DRIVE
3. CHANNEL INDICATOR
When channel 1 is selected, its RED LED will be illuminated. When channel 2 is select-
ed its YELLOW LED indicator is illuminated. Notice when the channel indicator is illuminated, the Effects indicator (14) matches the selected channel's color. This indicates the
stored effects setting when that channel is on.
4. CHANNEL VOLUME
The volume of the drive channels are to be used as a master level controls. For partial
clean output, set the VOLUME control to nearly 10 and turn the DRIVE nearly off.
5. CHANNEL DRIVE
The channel drive delivers 12AX7 tube saturation and EL34 power tube compression.
This channel incorporates a dual section lead DRIVE control with 72 dB of dynamic range.
So you can go from shimmering clean to fabulous blues soft clipping to full blown overdrive with total tube warmth. For mild 12AX7 tube emulation, set the DRIVE control
between 2 & 3. For some of the best saturation, set the control between 4 & 6. For full
blown drive, set the control between 6 and 10 (your guitar volume should be turned all
the way up). Because the SX AMP has a lot of gain in the DRIVE control, you can get
guitar feedback. If feedback is a problem, reduce the amount of DRIVE or move the guitar away from the speakers.
6. CHANNEL 1 HI-GAIN SWITCH
The Hi-Gain switch adds extreme gain and super scooped mids. This setting allows for
very long sustained notes and heavily over driven power chords.
7. CHANNEL 2 BLUES SWITCH
The exclusive BLUES SWITCH adds the critical mid tones in the 525 Hz range that are so
important to great sounding blues-rock tone. However, when the BLUES SWITCH is not
used (OUT), the SX delivers a great “scooped” sound for hard rock metal players. It is
important that you pre-select this switch for your style of playing before adjusting the
tone controls.
8. CHANNEL BASS, MID & TREBLE
These active tone controls develop the heart of your sound. It is important that you start
at the mid point (5) on each control. The total range of these controls are a substantial 20
dB (±10 dB) with a center frequency at 80 Hz for BASS, 600 Hz for MIDS and 8k Hz for the
TREBLE. These controls are very powerful in their effect, so take time to adjust each control for your ultimate sound.
9. CHANNEL PRESENCE SWITCH
The PRESENCE switch frequency range is at the very high end of the guitar spectrum (11k
Hz) for shimmering, glassy harmonics. If your sound is too dull, try the presence switch
for more highs.
CHANNEL 3 CLEAN
10. CHANNEL 3 INDICATOR
When channel 3 is select its GREEN LED indicator is illuminated.
11. CHANNEL 3 VOLUME
Channel switching from the Drive channels into
CHANNEL 3
gives you instant crisp, clean
sounds. Thanks to special mud-cutting circuits that work between the frequencies of 550
and 700 Hz, your guitar tones will be full and vibrant.
12. CHANNEL 3 BASS, MID & TREBLE CONTROLS
To start, set the BASS, MID & TREBLE controls at their center (5) position. These con-
trols are most likely to be set according to the type of pickups used (dual or single coil).
Most musicians like to reduce the MIDs deeper bass and crisper highs.
13. CHANNEL 3 PRESENCE SWITCH
For added clarity, the
CH 3 PRESENCE
control increases the highest guitar harmonics in the
8-11k Hz range. A normal bright switch works only in the 3-5k Hz range leaving your sound
somewhat flat.
Single or dual coil pickups will determine the use of this control.
DSP EFFECTS SECTION
14. SMART EFFECTS™ ADJUST
(PARAMETER)
CONTROLS
The 24-BIT processor provides a host of great sounding effects including FLANGE,
REVERB, ECHO, & CHORUS. Turn up the LEVEL control to 5 as a starting position. Turn the
LEVEL higher if more effect signal is desired. Use the SELECT and the ADJUST controls to
get the desired effect. Move the effects ADJUST and SELECT controls to the desired effect
for each channel. Each channel now has its own effects. Smart Effects™ will automatically store your last selected effect settings for each channel and will recall them when
you switch between channels. As you select each channel, notice that the LED next to the
LEVEL control changes color to match the channel LED color to indicate that the effects
has been changed. The settings are stored in memory even when the amp has been
SX300C, SX300H AND SX300R FRONT & REAR PANEL CONTROLS
1
5
2
8
6
2
SX
300
R
GUITAR PRE-AMP
INPUT B
P
H
O
N
E
S
OUTPUT TO
GUITAR AMP
-10 dB
+4 dB
-10 dB
+4 dB
BALANCED DIRECT OUT
TO MIXER
FS-44
FOOT
SWITCH
(NOT MIDI)
SPEAKER EMULATION
UN-
BAL.
8
4
4
5
3
3
7
9
9
26
20
21
19
27
POWER
EFFECTS ADJUST
REVERB
E
C
H
O
C
H
O
R
U
S
F
L
A
N
G
E
R
E
V
E
R
B
SEL
10
9
8
7
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
I
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
TREBLE
VOLUME
MID
BASS
3
SEL
PRESENCE
SX-300
turned off. To change the stored effect, simply select a new effect. Note: The SELECT
and the ADJUST controls do not rotate to their stored settings. Make note of your favorite
effect settings.
15. EFFECT PARAMETERS
Each of the four effects has two variable parameters that can be easily adjusted. The SELECT and
ADJUST parameters are described below.
A) ECHO: SELECT is the amount of the regeneration (repeating). The ADJUST controls the
delay time between the original signal and the echo.
B) REVERB: SELECT is the amount of presence (high frequencies) in the reverb. The
ADJUST is the decay time or length of reverb.
C) CHORUS: SELECT is the level of background reverb with your chorus. The ADJUST con-
trol increases the depth.
D) FLANGE: SELECT is the speed of your flange. The ADJUST control increases the depth.
16. SX300C & SX300H ALTERNATE REVERB SYSTEM
The REVERB SWITCH is an alternate reverb system that is independent from the Smart
Effects™ system. By pushing in the REVERB SWITCH, a small amount of reverb is added
to enhance your sound. The FS44 footswitch does not externally control this reverb,
which allows you to have reverb on at all times whether Smart Effects™ are ON or OFF.
17. EFFECTS OUTPUT LEVEL CONTROL
The effects LEVEL control is used to set the amount of effects you want blended into your
guitar. This control affects the overall effect levels including the alternate reverb system.
Note: The effects level is not controlled by the Smart Effects™ memory so you must
manually change it if you need different levels between channels.
18. POWER ON/OFF SWITCH & PILOT LIGHT (SX300C/H only)
The front power switch will turn on the power to the amplifier. The brass jeweled red
pilot light illuminates when the amp is powered on.
REAR PANEL
19. INPUT B (SX300R only)
This input is the same as the front panel input. The front panel input when used will over
ride the back panel input. This back panel input is great in a rack mount situation where
other rack mounted gear is used in front of the SX300R such as wireless units, external
effects, and tuners.
20. FS44 FOOTSWITCH JACK
This jack is NOT a MIDI jack. It is design for the Carvin FS44 quad footswitch. The FS44
will give you remote control channel switching and Smart Effects muting.
21. HEADPHONE
The stereo HEADPHONE 1/4” jack is “CABINET VOICED” to prevent excessive highs. This
greatly reduces ear fatigue. On the SX300R the +4/ -10dB switch affects headphone level.
22. CABINET VOICED LINE OUT OUTPUT
The voiced 1/4” LINE OUT gives the same response as if you were micing the speaker. Special
equalization reduces the harsh highs that are normally associated with a line out signal.
IMPORTANT: TO INSURE THAT THE SX300C DOES NOT SHUT OFF (PROTECTION
MODE), PLEASE SELECTED THE PROPER SPEAKER IMPEDANCE ON THE REAR. IF
YOUR SX300C/H TURNS OFF DURING A PERFORMANCE, SET THE IMPEDANCE TO 4Ω.
Speaker Switch Setting
1x 4Ω -4Ω
2x 8Ω -4Ω
1x 8Ω -8Ω
2x 16Ω -8Ω
1x 16Ω -16Ω
The following are settings to be used with Carvin cabinets loaded with Celestion speakers.
Note: these settings may not be suitable for cabinets with different speakers.
AMP MODEL CABINET SWITCH SETTING
SX300C Combo 2x12 8Ω
SX300C 2x12 ext. cabinet (total 4x12) 4Ω
SX300H 4x12 8Ω
SX300H 8x12 4Ω
23. SPEAKER OUTPUTS (SX300C/H only)
Both units have two 1/4" speaker output jacks and an impedance matching switch. The SX300C
combo uses one of these jacks for the internal two Celestion speakers. Be sure to set this
switch to the correct impedance setting when plugging in external speakers on the SX300C.
24. EFFECTS LOOP (SEND & RETURN) (SX300C/H ONLY)
Although the
SX300C
has built-in effects, you may want to use its separate effects loop. For
the lowest noise from a pedal effect, use this effects loop instead of plugging the guitar into the
effects and then into the amp. To use the
EFFECTS LOOP
, plug the input of your effects into
the
SEND
jack and the output of your effects into the
RETURN
jack. Use shielded cables.
25. AC POWER & FUSE
The SX300R is design to operate from 90-250VAC (50 or 60 Hz). The SX300C combo
and SX300H head come in 120VAC and 230VAC models for best power amp perform-
ance. All models should be plugged into a grounded "3 prong" outlet. No attempt should
be made to defeat or use the amp without the ground connected. The internal FUSE is
located inside the chassis. This is not user serviceable. Contact Carvin’s Service
Department at 800-854-2235 or carvin.com
26. SX300R SPEAKER EMULATOR OUTPUT DIRECT
The speaker Emulator outputs are for D.I. (Direct) connections to a PA system. These
outputs are custom shaped using 4 stages of filtering to emulate a speaker cabinet that
has been mic'ed. Both unbalanced 1/4" and balanced XLR are provided for any situation.
The +4/-10dB switch provides a final output level adjustment. Use the +4dB setting for
line level and -10dB setting for instrument level.
27. SX300R MAIN OUTPUT SECTION
These jacks are for going to the main power amplifier that is running guitar specific
speakers. This output should NOT be used to go to a PA system or other system with
non-guitar specific speaker cabinets. Both unbalanced 1/4" and balanced XLR are provided for any situation. If you are using an amplifier (like the Carvin DCM series), it is
best to use the XLR connector for the best level and lowest noise to the amplifier. The
+4dB setting is for line level and the -10dB setting is for instrument level.
MADE
AUS
IN THE
!
CAUTION ± TO PREVENT ELECTRICAL SHOCK DO NOT DEFEAT THE SAFETY
GROUND ON THE POWER CORD. DO NOT REMOVE COVER.
WARNING ± TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE TO RAIN
OR MOISTURE. REFER SERVICING TO QUALIFIED PERSONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
SERIAL NUMBER
INTERNAL FUSE
90-250 VAC 50-60Hz
125VA
x x x x x x
ADJUST
ECHO
REGEN TIME
REVERB
DAMPING DECAY
FLANGE
SPEED DEPTH
CHORUS
REV LEVEL DEPTH
SELECT
SX-AMPSX-AMP
DSP CONTROLS
13
14
18
20
25
17
SX300/SX300H REAR
22
21
23
24
11
12 15
2
10
16
18
14
SEND RETURN
VOICED
LINE OUT
PHONES
FS44 FOOT
SWITCH ONLY!
EFFECTS
SPEAKER
OUTPUT
SPK
IMP
4ΩΩ
ΩΩ
8ΩΩ
ΩΩ
16ΩΩ
ΩΩ
21
SX300
SX300
100 WATTS
SPKRS SW
1 x 4ΩΩ
ΩΩ
- 4ΩΩ
ΩΩ
2 x 8ΩΩΩΩ - 4ΩΩ
ΩΩ
1 x 8ΩΩ
ΩΩ
- 8ΩΩ
ΩΩ
2 x 16ΩΩΩΩ - 8ΩΩ
ΩΩ
1 x 16ΩΩΩΩ - 16ΩΩ
ΩΩ
IMPROPER
SETTINGS
WILL RESULT
IN HI-TEMP
PROTECTION!
SAFETY INSTRUCTIONS (EUROPEAN)
The conductors in the AC power cord are colored in accordance with the following code.
GREEN & YELLOW—Earth BLUE—Neutral BROWN—Live
U.K. MAIN PLUG WARNING: A molded main plug that has been cut off from the cord is
unsafe. NEVER UNDER ANY CIRCUMSTANCES SHOULD YOU INSERT A DAMAGED OR CUT MAIN PLUG INTO A POWER SOCKET.
IMPORTANT! FOR YOUR PROTECTION, PLEASE READ THE FOLLOWING:
WATER AND MOISTURE: Appliance should not be used near water (near a bathtub, washbowl,
kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc). Care should be taken
so that objects do not fall and liquids are not spilled into the enclosure through openings.
POWER SOURCES: The appliance should be connected to a power supply only of the type
described in the operating instructions or as marked on the appliance.
GROUNDING OR POLARIZATION: Precautions should be taken so that the grounding or polarization means of an appliance is not defeated.
POWER CORD PROTECTION: Power supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them, paying particular attention to
cords at plugs, convenience receptacles, and the point where they exit from the appliance.
SERVICING: The user should not attempt to service the appliance beyond that described in the
operating instructions. All other servicing should be referred to qualified service personnel.
FUSING: If your unit is equipped with a fuse receptacle, replace only with the same type fuse.
Refer to replacement text on the unit for correct fuse type.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL! THIS UNIT CONTAINS HIGH VOLTAGE INSIDE!
CAUTION
RISK OF ELECTRIC SHOCK
This symbol is intended to alert the user to the
presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons.
LIMITED WARRANTY
Your Carvin amplifier is guaranteed against failure for ONE YEAR unless otherwise stated. Carvin
will service and supply all parts at no charge to the customer providing the unit is under warranty.
Shipping costs are the responsibility of the customer. CARVIN DOES NOT PAY FOR PARTS OR SERVICING OTHER THAN OUR OWN. A COPY OF THE ORIGINAL INVOICE IS REQUIRED TO VERIFY
YOUR WARRANTY. Carvin assumes no responsibility for horn drivers or speakers damaged by this
unit. This warranty does not cover, and no liability is assumed, for damage due to: natural disasters,
accidents, abuse, loss of parts, lack of reasonable care, incorrect use, or failure to follow instructions.
This warranty is in lieu of all other warranties, expressed or implied. No representative or person is
authorized to represent or assume for Carvin any liability in connection with the sale or servicing of
Carvin products. CARVIN SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
When RETURNING merchandise to the factory, you may call 800-854-2235 for a return authorization number. Describe in writing each problem. If your unit is out of warranty, you will be charged
the current FLAT RATE for parts and labor to bring your unit up to factory specifications.
HELP SECTION
1) AMP WILL NOT TURN ON
Check the power to the amp. Check for tripped circuit breakers, unplugged extension cords or
power-strip switches that may be turned off.
2) SX200/H AMP SHUTS OFF WHILE PLAYING
Check the rear SPK IPM switch to make sure it is set properly. Switch to the 4Ω position if you
are unsure where to set it. If the problem continues, contact our service technicians.
3) NO OUTPUT with POWER LIGHT ON
Make sure that your speaker is functioning and not blown. Check input, cables & effects
connected to the effects loop, and extension speaker cables for defects & connections.
a) Also verify the effects loop is working by inserting a 1/4” stereo plug into the return jack and
short the tip and ring. If the amp works by doing this, the effects loop jack is defective.
4) KEEP YOUR AMP LOOKING NEW
Try to keep your amplifier free from dust and moisture. To clean, use a damp cloth to wipe the controls chassis panel and wipe the vinyl covering. Use a dry cloth to be sure the moisture is removed.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
SX300C COMBO 2x12” & SX300H
COMPONENT QTY/BILL U/M DESCRIPTION
SX300R:
03-00560 7 EACH STANDOFF W/ANTI SPIN .56X.25"
03-63294 1 EACH STANDOFF ALUM 6-32x .25x .94
05-01603 1 EACH PWR AC 3/16AWG 8' 2" W/PLUGS
05-62420 1 EACH CABLE RIBBON 24A 2P/ 8" W/HDR
05-64430 1 EACH CABLE RIBBON 24A 4P/12" W/HDR
05-68430 2 EACH CABLE RIBBON 24A 8P/12" W/HDR
06-10001 7 EACH PPH #4 X .875 TYPE AB BLACK
06-10045 6 EACH SMS PFH #6X .375 TYPE AB BLACK
06-10051 4 EACH MS PFH 6-32X .250 BLACK
06-10061 1 EACH SMS PPH #6 X .375 TYPE A BLACK
06-10133 2 EACH SMS PPH (#8x.375) TYPE A BLK.
06-50030 4 EACH NUT KEP #6-32 BLACK OXIDE
06-50035 1 EACH NUT KEP #6-32 ZINC CADMIUM
07-01603 12 EACH KNOB "6L" 6x6x17.4mm GREY CAP
07-00105B16 EACH KNOB SX BLACK W/WHITE NUMBERS
07-00106 1 EACH KNOB SX BLACK W/WHITE
10-03301B1 EACH FRONT PANEL SX300R
10-30005 1 EACH PANEL COVER TOPSIDE EQ/XC/XP
10-30014E 1 EACH CHASSIS UNIVERSAL ONE SPACE
77-03301B1 EACH LABEL FRONT SX300R
77-03303B1 EACH LABEL S/N OUTPUT JACKS SX300R
80-03301 1 EACH PCB ASSY MAIN SX300C RACK SMT PCB REV.
SX300C COMBO 2x12” & SX300H
COMPONENT QTY/BILL U/M DESCRIPTION
03-01200 1 EACH STRAIN RELIEF .625 CHS/.35 CBL
03-18190 1 EACH CABLE TIE 4”LX .10”W 7/8 BNDLE
03-21800A2 EACH MICA INSULATOR TO-218 0.002”
03-44319 1 EACH WASHER NYLON .157IDx.315Dx.197
03-49553 2 EACH TAPE W/ADHSVE 3M .375 X .375
03-52221 1 EACH GROMMET RUBBER .375” DIAMETER
03-60043 1 EACH SIL PAD W/ADHESIVE 9 MIL
03-77704 1 EACH LENS METAL RED THREADED
03-80602 4 EACH GROMMET NAT PLASTI SCRW #8/10
05-00111 1 EACH CABLE SPKR 24” 16AWG QUICK CON
05-00120 1 EACH CABLE SPEAKER JUMPER 150MM
05-01605 1 EACH PWR AC 16AWG SJT 8’ W/125MM ST
05-46020 1 EACH SPADE CONNECT 16AWG BLK 203MM
05-48025 1 EACH SPADE CONNECT 18AWG BLK 254MM
05-64410 1 EACH CABLE RIBBON 24A 4P/ 4” W/HDR
05-64435 1 EACH CABLE RIBBON 24A 4P/ 14” W/HDR
05-68415 1 EACH CABLE RIBBON 24A 4P/ 6” W/HDR
05-68430 1 EACH CABLE RIBBON 24A 8P/12” W/HDR
05-96545 1 EACH SPADE CONNECT 16AWG GRN/YEL 5”
06-09252 15 EACH NUT FOR POT 71-09252C
06-10070 8 EACH MS PPH 6-32X .500 BLACK
06-10133 2 EACH SMS PPH (#8x.375) TYPE A BLK.
06-10174 4 EACH SMS POH #10X 1.25 TYPE A BLACK
06-11120 1 EACH NUT METRIC 12MM KUNMING BLACK
06-11905 6 EACH NUT METRIC 9MM CHROME SHIMWOO
06-11906 6 EACH WSH METRIC 9MM CHROME SHIMWOO
06-30035 4 EACH WSH FLANGED #10 BLACK OXIDE
06-40070 1 EACH TERMINAL .25”TAB/.156”LUG/.032
06-50030 8 EACH NUT KEP #6-32 BLACK OXIDE
06-50053 4 EACH NUT RETAINER U-TYPE #10 SCREW
07-00105B16 EACH KNOB SX BLACK W/WHITE NUMBERS
07-00106 1 EACH KNOB SX FEATURE BLACK W/WHITE
10-03201D1 EACH CHASSIS SX-AMP 100W 3-CHANNEL
10-03202C 1 EACH COMBO HEAD
25-31350 1 EACH SWITCH DPST ROCKER BLACK POWER
76-00001 1 EACH WARRANTY CARD “CARVIN”
77-03300 1 EACH LABEL FRONT SX300C
77-03302 1 EACH LABEL OUTPUT JACKS SX300C
77-03204 1 EACH LABEL SERIAL NUMBER SX AMPS
80-03300 1 EACH PCB ASSY MAIN SX300C SMT PCB
87-20120 1 EACH CABINET ASSY SX300C 2X12 COMBO
87-3200 1 EACH CABINET ASSY. HEAD
REPLACEMENT PARTS LIST
Loading...