Carvin SX200, SX50, SX100 Owner's Manual
This symbol is intended to alert the user to the
presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be
of sufficient magnitude to constitute a risk of
electric shock to persons.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
IMPORTANT! FOR YOUR PROTECTION, PLEASE READ THE FOLLOWING:
WATER AND MOISTURE: Appliance should not be used near water (near a bathtub, washbowl,
kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc). Care should be taken so
that objects do not fall and liquids are not spilled into the enclosure through openings.
POWER SOURCES: The appliance should be connected to a power supply only of the type
described in the operating instructions or as marked on the appliance.
GROUNDING OR POLARIZATION: Precautions should be taken so that the grounding or polarization means of an appliance is not defeated.
POWER CORD PROTECTION: Power supply cords should be routed so that they are not likely
to be walked on or pinched by items placed upon or against them, paying particular attention to
cords at plugs, convenience receptacles, and the point where they exit from the appliance.
SERVICING: The user should not attempt to service the appliance beyond that described in the
operating instructions. All other servicing should be referred to qualified service personnel.
FUSING: If your unit is equipped with a fuse receptacle, replace only with the same type fuse.
Refer to replacement text on the unit for correct fuse type.
SAFETY INSTRUCTIONS (EUROPEAN)
The conductors in the AC power cord are colored in accordance with the following code.
GREEN & YELLOW—Earth BLUE—Neutral BROWN—Live
U.K. MAIN PLUG WARNING: A molded main plug that has been cut off from the cord is unsafe.
NEVER UNDER ANY CIRCUMSTANCES SHOULD YOU INSERT A DAMAGED OR CUT
MAIN PLUG INTO A POWER SOCKET.
REPLACEMENT PARTS LIST
SX50/100C SX-AMP COMBO 12” 100W
COMPONENT QTY/BILL U/M DESCRIPTION
For SX50:
80-03150-50 1 EACH PCB ASSY MAIN SX50 SMT PCB
For SX100:
80-03150-100 1 EACH PCB ASSY MAIN SX100 SMT PCB
Hardware For SX50 & SX100:
03-01200 2 EACH STRAIN RELIEF .625 CHS/.35 CBL
03-21800A 2 EACH MICA INSULATOR TO-218 0.002”
03-44319 1 EACH WASHER NYLON .157IDx.315Dx.197
03-49553 2 EACH TAPE W/ADHSVE 3M .375 X .375
03-60043 1 EACH SIL PAD W/ADHESIVE 9 MIL
03-77704 1 EACH LENS METAL RED THREADED
05-00111 1 EACH CABLE SPKR 24” 16AWG QUICK CON
05-01605 1 EACH PWR AC 16AWG SJT 8’ W/125MM ST
05-46020 1 EACH SPADE CONNECT 16AWG BLK 203MM
05-48025 1 EACH SPADE CONNECT 18AWG BLK 254MM
05-64410 1 EACH CABLE RIBBON 24A 4P/ 4” W/HDR
05-68415 1 EACH CABLE RIBBON 24A 8P/ 6” W/HDR
05-68430 1 EACH CABLE RIBBON 24A 8P/12” W/HDR
05-96545 1 EACH SPADE CONNECT 16AWG GRN/YEL 5”
06-09252 11 EACH NUT FOR POT 71-09252C
06-10070 8 EACH MS PPH 6-32X .500 BLACK
06-10174 4 EACH SMS POH #10X 1.25 TYPE A BLACK
06-11120 1 EACH NUT METRIC 12MM KUNMING BLACK
06-11905 4 EACH NUT METRIC 9MM CHROME SHIMWOO
LIMITED WARRANTY
Your Carvin product is guaranteed against failure for ONE YEAR unless otherwise stated.
Carvin will service and supply all parts at no charge to the customer providing the unit is under
warranty. Shipping costs are the responsibility of the customer. CARVIN DOES NOT PAY FOR
PARTS OR SERVICING OTHER THAN OUR OWN. A COPY OF THE ORIGINAL INVOICE IS
REQUIRED TO VERIFY YOUR WARRANTY. Carvin assumes no responsibility for horn drivers
or speakers damaged by this unit. This warranty does not cover, and no liability is assumed,
for damage due to: natural disasters, accidents, abuse, loss of parts, lack of reasonable care,
incorrect use, or failure to follow instructions. This warranty is in lieu of all other warranties,
expressed or implied. No representative or person is authorized to represent or assume for
Carvin any liability in connection with the sale or servicing of Carvin products. CARVIN SHALL
NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
SERVICE
In the USA, please call 800-235-2235 for a RMA # (return authorization number). Write this number
on the box and enclose a description of the problem. Prepay to Carvin 12340 World Trade Drive,
SD, CA 92128.
Outside the USA, contact your dealer or go to http://www.carvinworld.com for your nearest service
center. Include a written description of the problem with serial number and date of purchase.
HELP SECTION
1) AMP WILL NOT TURN ON
Check the power to the amp. Check for tripped circuit breakers, unplugged extension cords or
power-strip switches that may be turned off.
2) SX200/H AMP SHUTS OFF WHILE PLAYING
Check the rear SPK IPM switch to make sure it is set properly. Switch to the 4Ω position if you
are unsure where to set it. If the problem continues, contact our service technicians.
3) NO OUTPUT with POWER light ON
Make sure that your speaker is functioning and not blown. Check input, cables & effects
connected to the effects loop, and extension speaker cables for defects & connections.
a) Also verify the effects loop is working by inserting a 1/4” stereo plug into the return jack and
short the tip and ring. If the amp works by doing this, the effects loop jack is defective.
4) KEEP YOUR AMP LOOKING NEW
Try to keep your amplifier free from dust and moisture. To clean, use a damp cloth to wipe the
controls chassis panel and wipe the vinyl covering. Use a dry cloth to be sure the moisture is
removed.
CAUTION
RISK OF ELECTRIC SHOCK
06-11906 4 EACH WSH METRIC 9MM CHROME SHIMWOO
06-30035 4 EACH WSH FLANGED #10 BLACK OXIDE
06-40070 2 EACH TERMINAL .25”TAB/.156”LUG/.032
06-50030 8 EACH NUT KEP #6-32 BLACK OXIDE
06-50053 4 EACH NUT RETAINER U-TYPE #10 SCREW
07-00105B 11 EACH KNOB SX BLACK W/WHITE NUMBERS
07-00106 1 EACH KNOB SX FEATURE BLACK W/WHITE
10-03150 1 EACH CHASSIS SX50/100C
25-31350 1 EACH SWITCH DPST ROCKER BLACK POWER
76-00001 1 EACH WARRANTY CARD “CARVIN”
77-10000 1 EACH LABEL AMP PROD ID TAG
77-03102 1 EACH LABEL OUTPUT JACKS SX100/50C
77-03204 1 EACH LABEL SERIAL NUMBER SX AMPS
87-10120 1 EACH CABINET ASSY SX100
SX200 COMBO 2x12” & SX200H
COMPONENT QTY/BILL U/M DESCRIPTION
03-01200 1 EACH STRAIN RELIEF .625 CHS/.35 CBL
03-18190 1 EACH CABLE TIE 4”LX .10”W 7/8 BNDLE
03-21800A 2 EACH MICA INSULATOR TO-218 0.002”
03-44319 1 EACH WASHER NYLON .157IDx.315Dx.197
03-49553 2 EACH TAPE W/ADHSVE 3M .375 X .375
03-52221 1 EACH GROMMET RUBBER .375” DIAMETER
03-60043 1 EACH SIL PAD W/ADHESIVE 9 MIL
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL! THIS UNIT
CONTAINS HIGH VOLTAGE INSIDE!
CARVIN ENGINEERING DATA
SX50, SX100, SX200 & SX200H
SX200
SX100
SX50
SX200H
SX SERIES Classic Tube Emulation, awesome digital effects, rich black vinyl
covering and the brass red jewel light continue to make the AMERICAN MADE SX
Series one of the hottest amps on the market today!
EMULATION OR MODELING?
doesn’t just copy the sounds of other amplifiers – it actually emulates 12AX7 tube
circuitry. The SX waveforms successfully “emulates” real tube waveforms that
breathe and express warmth from a mild soft-clip to a full power soaked sustain.
Pro players and industry gurus have stated that the SX Tube Emulator actually
sounds better than many tube amps!
TWO CHANNELS
– Clean and Distortion. Each channel has its own indepen-
dent volume control for setting up equal levels quickly and easily. The SX200 and
SX200H adds true “DUAL CHANNEL 1 & 2” capabilities allowing both channels to
be played at the same time.
ACTIVE TONE CONTROLS
controls on both channels. The SX200 and SX200H goes even further by adding a
PRESENCE control to each channel for more high-end.
24-BIT EFFECTS
Once you have your tone, add in just the right amount of
lush REVERBS, rich CHORUSES, thick textured FLANGING and pristine ECHOES
using fully adjustable parameters for damping, decay, depth, speed, time and
regeneration–up to 256 24-BIT effects. The SX200 and SX200H adds a second
digital processor dedicated to creating a lush, concert-hall reverb at the push of a
button.
SX MODELS
The 50 watt SX50 with one heavy-duty 12”
speaker is perfect for any venue. The SX100, SX200 and SX200H feature a full
100 watts RMS – plenty for most situations. All combos & stacks feature the
heavy-duty speakers that provides awesome guitar reproduction – from clean to
blues to scream’n metal. The SX200 features two 12” speakers for an even bigger
For your records, you may wish to record the following information.
Serial No._____________________ Invoice Date_______________
76-10205E 0807
Unlike other “modeling” amps, the SX
All models feature BASS, MID and TREBLE
GUITAR AMPS
OPERATING MANUAL
sound. The SX200H head can be paired with either a 4x12 half stack or
8x12 full stack.
REAR PANEL CONNECTIONS
All back panels feature a voiced LINE
OUT for recording or running a slave amp, HEADPHONE jack, EXTENSION
SPEAKER jack and a FOOT SWITCH jack for the optional FS22 (for remotely
changing channels and turning on/off the effects). The extra dedicated
reverb on the SX200 & SX200H is controlled by a front panel switch. The
SX200 & SX200H also adds SEND/RETURN jacks for your own external
effects. A 4, 8, 16Ω impedance switch is featured for matching speakers.
RUGGED CONSTRUCTION
SMT surface mount electronics
ensure consistent, reliable performance and are nearly impervious to
bumps and vibrations. Strong, lightweight plywood cabinet (not particle
board), aluminum chassis, steel grille and corners deliver one of the lightest, yet most rugged amps available.
RECEIVING INSPECTION—read before getting started
INSPECT YOUR AMP FOR ANY DAMAGE which may have occurred during shipping. If any damage is found, please notify the shipping company and CARVIN
immediately.
SAVE THE CARTON & ALL PACKING MATERIALS. In the event you have to re-ship
your unit, always use the original carton and packing material. This will provide the
best possible protection during shipment. CARVIN and the shipping company are not
liable for any damage caused by improper packing.
SAVE YOUR INVOICE. It will be required for warranty service if needed in the
future.
SHIPMENT SHORTAGE. If you find items missing, they may have been shipped
separately. Please allow several days for the rest of your order to arrive before
inquiring.
RECORD THE SERIAL NUMBER on the enclosed warranty card or below on this
manual for your records. Keep your portion of the card and return the portion
with your name and comments to us.
SX SERIES SPECIFICATIONS:
Speakers: SX50, SX100, SX200 12”
Power: SX50: 50 watts @ 8Ω
SX100: 100 watts @ 8Ω
SX200/SX200H: 100 watts @ 4, 8, 16Ω
Output Impedance: 4-16 ohms switchable
Power Amp: THD: Less than 1%
Input Impedance: 100k ohms
Channels: 2—switching
Tone Controls: BASS: 80Hz
Drive Channel MID: 600Hz
TREBLE: 8k Hz
PRESENCE: 11k Hz (SX200 only)
Clean Channel BASS: 90Hz
MID: 575Hz
TREBLE: 9k Hz
PRESENCE: 8-11k Hz (SX200 only)
Ch 1 Sensitivity: 1mV for clipping, dynamic range 72dB
Ch 2 Sensitivity: 75mV for full output
Line Out: 1.5 VAC @ full power
Power: SX50/SX100: 90-250VAC, 50-60Hz, 125VA
SX200/SX200H: 120V or 240V model
Fuse: 5 amp 250V internal
Cabinet Size: SX50/SX100: 19.5W x 10.25D x 17.5”H
SX200: 26W x 10.25D x 17.5”H
SX200H: 24.5W x 9.5D x 10.5”H
Cabinet: Plywood–no particle board
Net Weight: SX50/SX100: 30 lbs, SX200: 44 lbs, SX200H: 24 lbs
Warranty: One Year
Options: FS22 footswitch,
CV211 cover SX100 & SX50
CV3212 cover SX200
CV3200 cover SX200H
POWER
VOLUME DRIVE TREBLE TREBLEVOLUME BASS MIDMIDBASS
CHANNEL 2CHANNEL 1
1
LEVEL ADJUSTPRESENCE
1/2
REVERB
PRESENCE
2
E
C
H
O
C
H
O
R
U
S
F
L
A
N
G
E
R
E
V
E
R
B
SELECT
1/2 2
INPUT
SX-200SX-200
EFFECTS
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
I
Mock
BLUES
Metal
Metal
POWER
VOLUME DRIVE TREBLE TREBLEVOLUME BASS MID INPUTMIDBASS
CHANNEL BCHANNEL A
A
OUTPUT ADJUSTPRESENCE
PK
REVERB
PRESENCE
B
E
C
H
O
C
H
O
R
U
S
F
L
A
N
G
E
R
E
V
E
R
B
SELECT
SX-200SX-200
Classic Tube Emulation
EFFECTS
Silkscreen
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
I
Mock
MADE
AUS
IN THE
!
CAUTION ± TO PREVENT ELECTRICAL SHOCK DO NOT DEFEAT THE SAFETY
GROUND ON THE POWER CORD. DO NOT REMOVE COVER.
WARNING ± TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE TO RAIN
OR MOISTURE. REFER SERVICING TO QUALIFIED PERSONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
SERIAL NUMBER
INTERNAL FUSE
90-250 VAC 50-60Hz
125VA
x x x x x x
ADJUST
ECHO REGEN TIME
REVERB DAMPING DECAY
FLANGE
SPEED DEPTH
CHORUS
REV LEVEL DEPTH
SELECT
SX-AMPSX-AMP
DSP CONTROLS
SEND RETURN
EXTENSION
SPEAKER
LINE OUT
PHONESFS22 FOOT
SWITCH
EFFECTS
POWER
SX-200SX-200
1
Classic Tube Emulation
CHANNEL BCHANNEL A
EFFECTS
A
REVERB
B
TREBLEVOLUME BASS MID PRESENCEDRIVE TREBLEMIDBASS PRESENCEVOLUME INPUT OUTPUT ADJUST
PK
1
0
10
9
8
7
6
5
4
3
2
I
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
front label
SX50, SX100, SX200 & SX200H FRONT & REAR PANEL CONTROLS
VOLUME DRIVE TREBLEVOLUME BASSMIDBASS
CHANNEL
2
CHANNEL
1
1
EFFECTS
ADJUST
2
INPUT MID
POWER
TREBLE
BLUES
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
E
C
H
O
C
H
O
R
U
S
F
L
A
N
G
E
R
E
V
E
R
B
SELECT
SEND RETURN
VOICED
LINE OUT
PHONESFS22 FOOT
SWITCH
EFFECTS
SPEAKER
OUTPUT
SPK
IMP
4Ω
8Ω
16Ω
21
SX200
SX200
100 WATTS
SPKRS SW
1 x 4Ω - 4Ω
2 x 8Ω - 4Ω
1 x 8Ω - 8Ω
2 x 16Ω - 8Ω
1 x 16Ω - 16Ω
IMPROPER
SETTINGS
WILL RESULT
IN HI-TEMP
PROTECTION!
EXT SPKR
8Ω MIN
LINE OUT
PHONES
FS22 FOOT
SWITCH
GETTING STARTED QUICKLY
If you are like most players, you probably want to plug in your new amp and get started
playing right away. You can read the rest of the manual later to learn the finer points of
operating your amp. In order to get started you will need your SX AMP, a 120 or 230 AC
grounded power outlet, your instrument, and a standard guitar cord. With the amp turned
off, you may now plug it into the proper AC voltage.
Now turn all the volume and overdrive controls off and set tone controls at their mid center
position. If you have purchased the FS22 foot switch, plug it into the rear foot switch jack for
switching the channels and effects. Note: The CH SELECT
SWITCH
must be in the OUT posi-
tion (CH 1) for the FS22 to function (only CH 2 will function if it’s in the wrong position).
Now, turn the POWER SWITCH ON. Gradually raise the volume and overdrive controls.
Check the BLUES SWITCH setting before adjusting the tone controls.
FRONT PANEL
1. INPUT 1 (INPUT 1/2 ON SX200 & SX200H)
Connect a 1/4” guitar cable to this input. The 1/2 CH SELECT SWITCH will toggle
between channel 1 and 2. Use a professional quality 1/4” plug shielded guitar cord
(Carvin SH25) no longer than 25 feet. A long cable will reduce the overall treble response
from your pickups. Note: For remote footswitching leave the 1/2 CH SELECT SWITCH
in the “out” (CH 1) position when connecting the FS22 footswitch.
2. INPUT 2 (DUAL CHANNELS SX200 & SX200H ONLY)
To use the true dual channel feature of the SX200 and SX200H, plug a second guitar into
INPUT 2. When a guitar is plugged into both inputs, the channels become independent
of each other and can be played simultaneously.
3. CHANNEL SELECT
Set the channel switch to the desired channel. The LED’s next to the CHANNEL 1/2 will
let you see which channel is functioning. Use CH 1 for overdrive/lead. Use CH 2 for
clean playing. For the FS22 footswitch to function, set the CH SELECT to the “ OUT” or
“CH 1” position.
CHANNEL 1 DRIVE
4. CHANNEL 1 INDICATOR
The RED LED will illuminate when the OVERDRIVE channel is selected.
5. CHANNEL 1 VOLUME
The volume of the drive channel is to be used as a master level control. For partial clean
output, set the VOLUME control to 10 and turn the DRIVE nearly off.
6. CHANNEL 1 DRIVE
The drive channel delivers 12AX7 tube saturation and EL34 power tube compression.
This channel incorporates a dual section lead DRIVE control with a 72 dB dynamic range
so you can get shimmering clean, a fabulous blues tone or soft clipping to full blown
overdrive with total tube warmth. For mild 12AX7 tube emulation, set the DRIVE control
between 2 & 3. For some of the best saturation, set the control between 4 & 6. For full
blown drive, set the control between 6 and 10 (your guitar volume should be turned all
the way up). Because the SX AMP has a lot of gain in the DRIVE control, you can get
guitar feedback. If feedback is a problem, reduce the amount of DRIVE or move the guitar
away from the speakers.
7. BLUES SWITCH
The exclusive BLUES SWITCH adds the critical mid tones in the 525 Hz range that is
so important to great sounding blues-rock tone. However, when the BLUES SWITCH is
not used (OUT), the SX delivers a great “scooped” sound for hard rock metal players. It
is important that you pre-select this switch for your style of playing before adjusting the
tone controls.
8. CHANNEL 1 BASS, MID & TREBLE
These active tone controls develop the heart of your sound. It is important that you start
at the mid point (5) on each control. The total range of these controls are a substantial 20
dB (±10 dB) with a center frequency at 80 Hz for BASS, 600 Hz for MIDS and 8k Hz for
the TREBLE. These controls are very powerful in their effect so take time with the different
settings for your ultimate sound.
9. CHANNEL 1 PRESENCE (SX200/H ONLY)
Channel 1 features its own PRESENCE for added treble. It’s frequency range is at the
very high end of the guitar spectrum (11k Hz) for shimmering, glassy harmonics. If
your sound is too bright with single coil pickups, you may want to adjust the PRESENCE
control and TREBLE control.
CHANNEL 2 CLEAN
10. CHANNEL 2 CLEAN INDICATOR
The GREEN LED will illuminate when the CLEAN channel is selected.
11. CHANNEL 2 CLEAN VOLUME
Channel switching from the Drive channel into
Thanks to special mud-cutting circuits that work between the frequencies of 550 and 700 Hz,
your guitar tones will be full and vibrant.
12. CHANNEL 2 BASS, MID & TREBLE CONTROLS
To start, set the BASS, MID & TREBLE controls at their center (5) position. These controls are most likely to be set according to the type of pickups used (dual or single coil).
Most musicians like to reduce the MIDs deeper bass and crisper highs.
13. CHANNEL 2 CLEAN PRESENCE (SX200/H ONLY)
For added clarity, the
4
CH 2 PRESENCE
7
CHANNEL 2
gives you crisps, clean sounds.
control increases the highest guitar harmonics in the
3
8-11k Hz range. A normal bright switch works only in the 3-5k Hz range leaving your sound
somewhat flat.
DSP EFFECTS SECTION
14. SMART EFFECTS™ ADJUST (PARAMETER) CONTROLS
Single or dual coil pickups will determine the level of this control.
The 24-BIT processor provides a host of great sounding effects including FLANGE,
REVERB, ECHO, & CHORUS. Turn up the LEVEL control to 5 as a starting position. Turn
the LEVEL higher if more effect signal is desired. Use the SELECT and the ADJUST controls to
get the desired effect. Each channel now has its own effects. Move the EFFECTS ADJUST
and SELECT controls to the desired effect for each channel. Smart Effects™ will automatically store your last selected effect settings for each channel and will recall them
when you switch between channels. As you select each channel, notice that the 1 /2 LED
next to the LEVEL control changes color to match the channel LED color to indicate that
the effects has been changed. The settings are stored in memory even when the amp
has been turned off. To change the stored effect, simply select a new effect. Note: The
SELECT and the ADJUST controls do not rotate to their stored settings. Make note of your
favorite effect settings.
REAR PANEL
19. FOOTSWITCH
Carvin’s FS22 dual footswitch is recommended for remote channel switching and DSP
effects ON/OFF switching. Most foot pedals with 2 switches featuring a stereo plug will
work. For channel switching, be sure that the 1/2 CHANNEL select switch between the
channels is in the “OUT” position. If only CH 2 works, the 1/2 channel select switch is
in the wrong position.
20. HEADPHONE
The stereo HEADPHONE 1/4” jack is “CABINET VOICED” to prevent excessive highs.
This greatly reduces ear fatigue.
21. CABINET VOICED LINE OUT OUTPUT
The voiced 1/4” LINE OUT gives the same response as if you were micing the speaker. Special
equalization reduces the harsh highs that are normally associated with a line out signal.
22. SPEAKER OUTPUT
A 1/4” SPEAKER OUTPUT is featured to operate an extension speaker system. The
15. EFFECT PARAMETERS
Each of the four effects has a variable parameter that can be easily adjusted. Each “SELECT” &
“PARAMETER” is described below.
A) ECHO: SELECT the amount of the regeneration (repeating). Now select the ADJUST
control for the shortest or longest delay time between the original signal and the echo.
B) REVERB: SELECT the amount of presence (high frequencies) in the reverb. Now turn the
ADJUST control to provide the minimum or maximum decay.
C) CHORUS: SELECT the amount of reverb with your chorus. Now turn the ADJUST control
to increase the depth.
D) FLANGE: SELECT the amount of speed with your flange (phasing effect). Now turn the
ADJUST control to increase the depth.
16. SX200 & SX200H ALTERNATE REVERB SYSTEM
The SX200 & SX200H also features an alternate reverb system that is independent from
the Smart Effects™ system. By pushing in the REVERB SWITCH, you have a modest
amount of reverb added to both channels to enhance your sound. The FS22 footswitch
does not externally control this reverb, which allows you to have reverb on at all times
whether Smart Effects™ are ON or OFF.
17. EFFECTS OUTPUT LEVEL CONTROL
The effects LEVEL control is used to set the amount of effects you want blended into
your guitar. This control affects the overall effect levels including the alternate reverb
system featured on the SX200. Note: The effects level is not controlled by the Smart
Effects™ memory so you must manually change it if you need different levels between
channels.
minimum impedance of an extention speaker for the SX50, SX100 is 8Ω. The SX200
and SX200H has a switchable impedance of 4, 8 and 16 ohms. Set this accordingly
when adding additional speakers. IMPORTANT: TO INSURE THAT THE SX200 DOES
NOT SHUT OFF (PROTECTION MODE), PLEASE SELECTED THE PROPER SPEAKER
IMPEDANCE ON THE REAR. IF YOUR SX200/H TURNS OFF DURING A PERFORMANCE,
SET THE IMPEDANCE TO 4Ω.
Speaker Switch Setting
1x 4Ω - 4Ω
2x 8Ω - 4Ω
1x 8Ω - 8Ω
2x 16Ω - 8Ω
1x 16Ω - 16Ω
The following are settings to be used with Carvin cabinets loaded with 12” speakers.
Note: these settings may not be suitable for cabinets with different speakers.
AMP MODEL CABINET SWITCH SETTING
SX200 Combo 2x12 8Ω
SX200 2x12 ext. cabinet (total 4x12) 4Ω
SX200H 4x12 8Ω
SX200H 8x12 4Ω
23. EFFECTS LOOP (SEND & RETURN) (SX200/H ONLY)
Although the
the lowest noise from a pedal effect, use this effects loop instead of plugging the guitar into the
effects and then into the amp. To use the
the
SEND
SX200
has built-in effects, you may want to use its separate effects loop. For
EFFECTS LOOP
jack and the output of your effects into the
, plug the input of your effects into
RETURN
jack. Use shielded cables.
24. AC POWER & FUSE
The AC POWER CORD is designed to operate with any voltage from 90-250VAC, 50-
10
18. POWER ON/OFF SWITCH & PILOT LIGHT
The front power switch will turn on the power to the amplifier. The brass jeweled red
pilot light illuminates when the amp is powered on.
16
60Hz. Plug the cord into a grounded “3” prong” power source. No attempt should ever
be made to defeat or use the amp without the ground connected.
The internal FUSE is located inside the chassis. This is not user serviceable. Contact
18
Carvin’s Service Department at 800-854-2235 or carvin.com
1
1
2
5
5
6
6
7
4
8
3
11
8
9
11
10
12
18
13
17
14
15
SX50/SX100 REAR
21
VOICED
SX200/SX200H REAR
23
21
19
15
12
17
14
20
22
19
20
22
24
Loading...