Carver CV-1501, CV-1502, CV-2501, CV-2502, CV-4002 Owners manual
CV Series
User Manual
User Manual
User ManualUser Manual
This User Manual is made available in Adobe Acrobat format.
In order to view the manual and utilize it’s enhancements we
recommend that you download Adobe Acrobat Reader® 4.0 or
greater. If you do not currently have this viewer installed on your
computer, or you have an older version the reader is available
as a free download at http://www.adobe.com.
By going to the table of contents you can directly access any
topic outlined there, by simply clicking on the topic.
i
ON Media is a registered trademark of Carver Professional, A Phoenix Gold International Company
AMX, PANJA and Crestron are the registered trademarks of their respective owners.
© Phoenix Gold International, Inc. February 2001
Rev 04.08.021 - 1 –
SAFETY INFORMATION
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK DO NOT REMOVE
COVER. NO USER SERVICABLE PARTS
INSIDE. REFER SERVICING TO
QUALIFIED PERSONNEL
!
The lightning flash with arrowhead symbol within an
equilateral triangle is intended to alert the user to
the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle
is intended to alert the user of the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
Please read this entire manual, especially the Safety Warnings, before operating your
amplifier.
TABLE OF CONTENTS
Introduction 3
Unpacking and Paperwork 3
Features and Specifications
CV1501 4-5
CV2501 4-5
CV1502 6-7
CV2502 6-7
CV4002 8-9
Controls and Functions 10-14
Rack Mounts 10
Level Controls 10
LED Status Display 10
LED Level Display 10
Power Switch 11
Standby LED 11
Data LED 11
Output Connector 12
Sequence Connector 12-13
Remote Level Control 13
Standard Input Module 13
AC Line Cord 13
Configuration DIP Switch 14
Effects Loop 14
Installation and Operation
Location and General Precaution 14
Mechanical Considerations 14
Rear Support 14
Thermal Considerations 15
AC Power Considerations 15
Magnetic Leakage 15
Input Wiring 15-16
Input Sensitivity 16
Loudspeaker Polarity 16
Mono Operation 16-17
Bridged Mono Connections 17
Power Sequencing 18-20
Remote Level Control 20-22
Effects Loop 22
CV Series Block Diagram 22
Warranty Information 23
In Case Of Difficulty 24-25
Appendix A 26
Appendix B 27
Rev 04.08.021 - 2 –
INTRODUCTION
Congratulations on your purchase of a new Carver Professional CV Series Power
Amplifier. The CV Series amplifiers are designed expressly for commercial and
institutional audio applications. The CV Series amplifiers are designed and manufactured
by Carver Professional, a division of Phoenix Gold International, Inc. They combine
Carver Professional’s experience in pro audio along with the needs of the system
integrator to provide an uncompromising product for the commercial sound industry. The
sonic heritage of Carver Professional combined with the performance, manufacturing
quality and attention to detail that has defined Phoenix Gold International assures you of
the value and integrity you seek in an amplifier product. Thank you for placing your
confidence in Carver Professional and Phoenix Gold. We know your amplifier will
provide many years of dependable service and reliable sound reproduction.
Please read this entire manual, especially the Safety Warnings, before operating your
amplifier.
U
NPACKING
Carefully unpack the amplifier and keep the original carton and packing materials for future
moving, shipment or long-term storage. After opening the box, please check for visible signs
of damage that were not apparent from the outside of the box. If you encounter what appears
to be concealed damage, please contact your Carver Professional Dealer before installing
unit.
Important Paperwork
Make sure to save your sales receipt. Your receipt is extremely important to establish the
duration of your Limited Warranty and for insurance purposes. Next, make a note of the
serial number, which is located on the back of the amplifier. Record it in the space provided
below for convenient reference.
Model: _______________ Serial Number: __________________________
Purchased at: __________________________ Date: _________________
Finally, take a moment to fill out the Warranty Registration Card packed with the amplifier and
return it to Carver Professional. This will allow us to keep you informed about new products,
as they become available
.
A
ND
P
APERWORK
Rev 04.08.021 - 3 –
CV1501 CV2501
Power Output Power Output
• 150W mono into 4 ohm and 8 ohm loads, • 250W mono into 4 ohm and 8 ohm loads,
autoformer coupled, 40Hz to 20kHz ±3db autoformer coupled 40Hz to 20kHz ±3dB
with < 0.5% THD at full power with < 0.5% THD at full power
• 150W mono transformer coupled @ 25V, • 250W mono transformer coupled @ 25V,
35V, 50V, 70V and 100V 40Hz to 18kHz ±3dB 35V, 50V, 70V and 100V, 40Hz to 18kHz ±3dB
with < 0.5% THD at full power with < 0.5% THD at full power
Common Features
• Convection Cooling
• 5 segment LED level display per channel
including signal present and clip indicators
• 3 LED display per channel of Power, Protect
and Thermal Overload
• Standby LED indicates the amplifier is in
Standby Mode
• Data LED (used with Computer Control &
Monitoring module)
• Level control can be covered with a snap in
cap (supplied) to prevent tampering
• Remote Control of output level via Euro Style
connector
• Unbalanced Effects Loop (send/receive) via
Euro Style Connector
• Standard Mono Input Module with line level
input via Euro Style connector and XLR jack,
connected in parallel
• Switched Clip Limiter
• 26Hz High Pass Filter
• Switched 80Hz and 120Hz (12db/Octave cut)
High Pass Filters
• Terminals for Sequencing Power ON/OFF
• Speaker Output via large gauge Euro Style
connectors
• Power Switch, 3 positions On, Off, Standby
• AC Line Cord (Detachable IEC Type)
• Optional Accessories:
− Four Input Mixer Module with zone assignment
− Paging Modules with variable ducking
− Expanded Mic/Line Level Input Module
ON
− Computer Control & Monitoring via
Media Control Module
− DSP control of 28 Band Graphic EQ, 5 Band
Parametric EQ, HP Filter, LP Filter, Crossover,
Adjustable Limiting and Adjustable Delay via
ON Media DSP Tools Module
i
i
Rev 04.08.021 - 4 –
SPECIFICATIONS with Basic input module
PERFORMANCE:
•••• THD: <0.5% @ rated power, 0.2% 1/8 rated power at1 kHz
•••• IMD DIM30 Method: <0.2%
•••• Dynamic Headroom: 1.5dB
•••• Power Bandwidth: 40 Hz to 20 kHz, 4 and 8 ohm loads
•••• Frequency Response: 30 Hz to 20 kHz +0.5, -3dB(4 and 8 ohm loads)
•••• Signal-to-Noise: 94dB (typical), A-weighted, referred to rated power
•••• CMRR: 75dB at 1kHz
•••• Slew Rate: 7V/µSec
•••• Sensitivity for rated power (includes EFX Inputs): 0dBu or 0.775 V
•••• Input Impedance (includes EFX Inputs): 50kΩ balanced
•••• Input Overload (includes EFX Inputs): 20 dBu
•••• Protection: Thermal, Short Circuit, Over-current & Over Voltage, self-resetting
•••• Stability: Unconditionally stable into reactive loads
•••• Duty Cycle: Continuous operation with dynamic signal at 1/3rd power
POWER REQUIREMENTS:
•••• Mains Voltage (output power rated at nominal voltage): 100VAC, 50-60Hz ±20%
230VAC, 50Hz ±20%
rms
120VAC, 60Hz ±20%
• Power Consumption (See Appendix A)
REGULATORY COMPLIANCE:
•••• Proposed ETL/C Mark to: UL6500, 2
•••• CE Certification to: EN55103-1 & EN55103-2
nd
Edition
PHYSICAL:
•••• Cooling Method: Convection
•••• Operating Environment: -10
•••• Storage Environment: -45
•••• Dimensions: 3.5” H (2U) x 19.0” W x 16” D
89mm x 483mm x 438mm
•••• Net Weight: CV1501 – 27.4lbs / 12.4kg
CV2501 – 32.7lbs / 14.9kg
•••• Shipping Weight: CV1501 – 32.9lbs. / 15.0kg
CV2501 – 38.2lbs. / 17.4kg
o
C to 55oC, up to 85% RH
o
C to 70oC, up to 93% RH
Rev 04.08.021 - 5 –
CV1502 CV2502
Power Output Power Output
• 150W per channel into 4 ohm and 8 ohm loads, • 250W per channel into 4 ohm and 8 ohm loads,
autoformer coupled, 40Hz to 20kHz ±3dB autoformer coupled, 40Hz to 20kHz ±3dB
with < 0.5% THD at full power with < 0.5% THD at full power
• 150W per channel, transformer coupled @ 25V, • 250W per channel, transformer coupled @ 25V,
35V, 50V, 70V and 100V, 40Hz to 18kHz ± 3dB 35V, 50V, 70V and 100V, 40Hz to 18kHz ± 3dB
with < 0.5% THD at full power
• 300W parallel mono at 4 Ohms, 300W parallel • 500W parallel mono at 4 Ohms, 500W parallel
and bridged mono at 8 and 16 Ohms, 50V, 70V, and bridged mono at 8 and 16 Ohms, 50V, 70V,
100V, 140V and 200V with no more than 0.5% THD 100V, 140V and 200V with no more than 0.5% THD
Common Features
• Convection Cooling
• 5-segment LED level display, per channel,
including signal present and clip indicators
• 3 LED display, per channel, of Power, Protect and
Thermal Overload
• Standby LED indicates the amplifier is in Standby
Mode
• Data LED (used with Computer Control module)
• Level controls can be covered with a cap
(supplied) to prevent tampering
• Remote control of output level via Euro Style
connector
• Unbalanced Effects Loop (send/receive) via Euro
Style Connector
• Standard Dual Input Module with line level inputs
via Euro Style connectors and XLR jacks,
connected in parallel
• Switched Clip Limiters
Rev 04.08.021 - 6 –
• 26Hz High Pass Filters
• Switched 80Hz and 120Hz (12db/Octave cut)
High Pass Filters
• Terminals for Sequencing Power ON/OFF
• Speaker Outputs via large gauge Euro Style
connectors
• Power Switch, 3 positions On, Off, Standby
• AC Line Cord (Detachable IEC Type)
• Optional Accessories:
− Four Input Mixer Module with zone assignment
− Paging Modules with variable ducking
− Expanded Mic/Line Level Input Module
ON Media
− Computer Control & Monitoring via
Control Module
− DSP control of 28 Band Graphic EQ, 5 Band
Parametric EQ, HP Filter, LP Filter, Crossover,
Adjustable Limiting and Adjustable Delay via
ON Media DSP Tools Module
i
i
SPECIFICATIONS with Basic input module
PERFORMANCE:
• THD: 0.5% at rated power, 0.2% at 1/8 rated power at 1kHz
•••• IMD DIM30 Method: <0.2%
•••• Dynamic Headroom: 1.5dB
•••• Power Bandwidth: 40 Hz to @20 kHz +0.5, -3 dB
•••• Frequency Response: 26 Hz to 20 kHz, 4 and 8 ohm loads
•••• Signal-to-Noise 94dB (typical), A-Weighted, referred to rated power
•••• Crosstalk: -60dB, full bandwidth
•••• CMRR: 75dB at 1kHz
•••• Slew Rate: 7V/µSec
•••• Sensitivity for rated power (includes EFX Inputs): 0dB or 0.775V
•••• Input Impedance (includes EFX Inputs): 50k balanced
•••• Input Overload (includes EFX Inputs): 20dBu
•••• Protection: Thermal, Short Circuit, and Over-current & Over Voltage
•••• Stability: Unconditionally stable into reactive loads
•••• Duty Cycle: Continuous operation at 1/3 rated power
POWER REQUIREMENTS:
•
• Mains Voltage (output power rated at nominal voltage): 100VAC, 50-60Hz ±20%
••
rms
120VAC, 60Hz ±20%
230VAC, 50Hz ±20%
• Power Consumption (See Appendix A)
REGULATORY COMPLIANCE:
•••• Proposed ETL/C Mark to: UL6500, 2
•••• CE Certification to: EN55103-1 & EN55103-2
nd
Edition
PHYSICAL:
•••• Cooling Method: Convection
•••• Operating Environment: -10
•••• Storage Environment: -45
•••• Dimensions: 3.5” H (2U) x 19.0” W x 17.25” D
89mm x 483mm x 438mm
•••• Net Weight: CV1502 – 35.1lbs / 15.9kg
CV2502 – 42.5lbs / 19.3kg
•••• Shipping Weight: CV1502 – 41.0lbs. / 18.0kg
CV2502 – 48.0lbs. / 22.0kg
o
C to 55oC, up to 85% RH
o
C to 70oC, up to 93% RH
Rev 04.08.021 - 7 –
CV4002
Power Output
• 400W per channel into 4 ohm and 8 ohm loads, autoformer coupled,
40Hz to 20kHz ±3dBwith < 0.5% THD at full power
• 400W per channel, transformer coupled @ 25V, 35V, 50V, 70V and 100V,
40Hz to 18kHz ±3dB with < 0.5% THD at full power
• 800W in parallel mono at 4 Ohms, 800W parallel and bridged mono at 8 and 16 Ohms,
50V, 70V, 100V, 140V and 200V, with no more than 0.5% THD
Common Features
• Convection Cooling
• 5-segment LED level display, per channel,
including signal present and clip indicators
• 3 LED display, per channel, of Power, Protect and
Thermal Overload
• Standby LED indicates the amplifier is in Standby
Mode
• Data LED (used with Computer Control Module)
• Level controls can be covered with a cap
(supplied) to prevent tampering
• Remote control of output level via Euro Style
connector
• Unbalanced Effects Loop (send/receive) via Euro
Style Connector
• Standard Dual Input Module with line level inputs
via Euro Style connectors and XLR jacks,
connected in parallel
• Switched Clip Limiters
• 26Hz High Pass Filters
• Switched 80Hz and 120Hz (12db/Octave cut)
High Pass Filters
• Terminals for Sequencing Power ON/OFF
• Speaker Outputs via large gauge Euro Style
connectors
• Power Switch, 3 positions On, Off, Standby
• AC Line Cord (Detachable IEC Type)
• Optional Accessories:
− Four Input Mixer Module with zone assignment
− Paging Modules with variable ducking
− Expanded Mic/Line Level Input Module
− Computer Control & Monitoring via ION Media
Control Module
− DSP control of 28 Band Graphic EQ, 5 Band
Parametric EQ, HP Filter, LP Filter, Crossover,
Adjustable Limiting and Adjustable Delay via
ON Media DSP Tools Module
i
Rev 04.08.021 - 8 –
SPECIFICATIONS with Basic input module
PERFORMANCE:
• THD: 0.5% at rated power, 0.2% at 1/8 rated power at 1kHz
•••• IMD DIM30 Method: <0.2%
•••• Dynamic Headroom: 1.5dB
•••• Power Bandwidth: 40 Hz to 20 kHz 4 and 8 ohm loads
•••• Frequency Response: 26 Hz to 20 kHz +0.5, -3 dB 4 and 8 ohm loads
•••• Signal-to-Noise 94dB (typical), A-Weighted, referred to rated power
•••• Crosstalk: -60dB, full bandwidth
•••• CMRR: 75dB @ 1kHz
•••• Slew Rate: 7V/µSec
•••• Sensitivity for rated power (includes EFX Inputs): 0dB or 0.775V
•••• Input Impedance (includes EFX Inputs): 50k balanced
•••• Input Overload (includes EFX Inputs): 20dBu
•••• Protection: Thermal, Short Circuit, and Over-current & Over Voltage
•••• Stability: Unconditionally stable into reactive loads
•••• Duty Cycle: Continuous operation at 1/3 rated power
POWER REQUIREMENTS:
•
• Mains Voltage (output power rated at nominal voltage): 100VAC, 50-60Hz ±20%
••
230VAC, 50Hz ±20%
120VAC, 60Hz ±20%
rms
• Power Consumption (See Appendix A)
REGULATORY COMPLIANCE:
•••• Proposed ETL/C Mark to: UL6500, 2
•••• CE Certification to: EN55103-1 & EN55103-2
PHYSICAL:
•••• Cooling Method: Convection
•••• Operating Environment: -10
•••• Storage Environment: -45
•••• Dimensions: 5.25” H (2U) x 19.0” W x 17.25” D
133mm x 483mm x 438mm
•••• Net Weight: CV4002 – 54.0lbs. / 24.5kg
•••• Shipping Weight: CV4002 – 60.0lbs. / 27.3kg
Rev 04.08.021 - 9 –
o
C to 55oC, up to 85% RH
o
C to 70oC, up to 93% RH
nd
Edition
Loading...