Page 1
SPECIFICATIONS
Printed in U.S.A. B25 0412
Carter-Hoffmann is a trademark
of Carter-Hoffmann LLC.
BB40, BB48, BB60 & BB72
BANQUET CARTERS
for plates 8-3/4” to 10-1/2” in diameter
CONSTRUCTION...Completely welded
double wall cabinet construction with
outer cabinet formed and welded to base.
All seams turned in to eliminate raw
edges.
CABINET MATERIAL...All stainless steel
construction; 20 gauge polished exterior
and 24 gauge interior.
BASE FRAME...12 gauge stainless steel
full depth bolsters with 1”x1” stainless
steel perimeter channel supports.
CASTERS...6” diameter, industrial grade
polyurethane casters. Two swivel and two
rigid. Sealed roller axle bearing and
double ball bearing swivel. Plate
mounted and bolted to base in offset
“wheel ahead” pattern. Two casters fitted
with brakes.
BUMPER...Non-marking gray vinyl
bumper set in heavy duty 3/16” extruded
aluminum frame with reinforced corner
“cut-outs.”
INSULATION...1” thick high density
continuous wrap-around type fiberglass
insulation with 1 1/2” thickness on top.
GASKET...High temperature silicone
gasket.
DOORS...Welded double stainless steel
door. Filled with 1” thick fiberglass
insulation.
HINGES...Concealed, stainless steel
hinge with 5/16” pin.
PUSH HANDLES... Two horizontal full
width stainless steel tubular push handles
with back-up plates. Mounted to each
end of the cabinet.
LATCHES...Flush mounted, heavy-duty
sliding latch(es) with exclusive grip
handle.
SHELVES...Welded, duplex nickel-plated
removable wire shelves.
THERMOMETER...Dial type with remote
sensing bulb and sensing bulb protector.
Mounted to door.
HEATING SYSTEM...Bottom mounted
heater. Stainless steel construction.
Removable without tools. 1600 watt
inconel-sheathed heating element. High
impedance protected, internally cooled
fan motor. Full range thermostat and
power indicating light.
ELECTRICAL CHARACTERISTICS...
Operates on 120 volts, 60 cycle, single
phase, 1650 watts, 13.7 amps. Ten foot
rubber cord with 3 pring grounding plug.
NEMA 5-15P plug.
PERFORMANCE...Capable of heating to
200OF (94OC). Preheat to 160OF (71OC)
in approximately 20 minutes.
ACCESSORIES/OPTIONS...
4 wheel brakes
Alternate electrical configurations
On/Off heater toggle switch
Top mounted transport latch
Locking paddle latch
Lexan thermometer cover
Cold plate
Alternate caster sizes & types
Menu card holder
Plate carriers - specify open “P” type
or covered plate “C” type
CARTER-HOFFMANN
1551 McCormick Ave., Mundelein, IL 60060
(847) 362-5500 • (800) 323-9793 • Fax (847) 367-8981
www.carter-hoffmann.com
Model Plate Capacity* Number Clearance Shelf Overall Dimensions Caster Shipping
Number with “P” with “C” without of
Between Shelves Size Height Depth Width Diameter Weight
carriers carriers carriers
Shelves in mm in mm in mm in mm in mm in mm lbs kgs
BB40 40 40 48 2 16 330 24x22 610x559
46
1
/
4
1175 30
1
/
2
775 32 813 6 152 230 105
# carriers 4 (10P) 4 (10C)
-
BB48 48 48 60 3 13 406
24x22 610x559 54 1372 30
1
/
2
775 32 813 6 152 265 120
# carriers 6 (8P) 6 (8C) -
BB60 60 60 72 2 16 406
32x22 838x559 46
1
/
4
1175 30
1
/
2
775 40
1
/
2
1029 6 152 290 132
# carriers 6 (10P) 6 (10C) -
BB72 72 72 90 3 13 330 32x22 838x559 54 11372 30
1
/
2
775 40
1
/
2
1029 6 152 310 141
# carriers 9 (8P) 9 (8C) -
BB48
shown with optional transport latch
& menu card holder
FOOD SERVICE EQUIPMENT
BANQUET CARTS
CARTER-HOFFMANN
BB48
Front View
Carter-Hoffmann CAD Drawing Scale: 1/4” = 1’
BB40 & BB48
Top View
BB60 & BB72
Top View
BB40
Front View
BB72
Front View
NSF/ANSI 4
BB60
Front View
Specifications subject to
change through product
improvement & innovation.
*Capacity based on common plate depth and combined plate/cover height of 2.5”. Due to the variety of plate thicknesses and depths, as well as plate cover heights; actual
capacity may vary.
Page 2
BB40, BB48, BB60 & BB72
BANQUET CARTERS
FEATURES & BENEFITS
1551 McCormick Avenue, Mundelein, Illinois 60060
Tel. (847)362-5500
.
(800)323-9793
.
Fax (847)367-8981
www.carter-hoffmann.com
Since 1947, Foodservice Equipment That Delivers!
COMPLETELY WELDED
TURNED-IN SEAM
CONSTRUCTION... Adds
rigidity to entire cabinet and
eliminates raw edges for
ease of cleaning and
safety.
REMOVABLE WIRE SHELVES...Welded, duplex
nickel-plated with reinforced shelf clips. Sturdy for
heavy plate loads and removable for cleaning.
WRAP-AROUND
BUMPER...Full perimeter
aluminum bumper with nonmarking gray vinyl insert.
Protects cart and facility
walls from damage.
6” DIAMETER INDUSTRIAL GRADE CASTERS
WITH POLYURETHANE TREAD... Long lasting
and easy rolling for maximum load and minimum
maintenance. Two swivel and two rigid. Swivel
casters fitted with brakes. Mounted to base in offset
wheel-ahead pattern for easy rolling over uneven
surfaces.
HIGH PERFORMANCE REMOVABLE HEATER...
Blower system for fast heat up, recovery and even
heat distribution throughout cabinet. Removable
without tools for easy service and cabinet cleaning.
HEAVY-DUTY STAINLESS
STEEL BASE FRAME... 12
gauge caster bolsters with
perimeter frame for rugged
use and added durability.
DOUBLE WALL
STAINLESS STEEL
CABINET... Strongest, most
durable materials for long
life. High density 1” thick
fiberglass in walls and door,
1 1/2” thick on top for
maximum heat retention.
NSF/ANSI 4
BB48
shown with optional transport latch
OPTIONAL PLATE CARRIERS... ”P” or “C” carriers are
available. “P” type holds 8-3/4” to 10-1/2” diameter open
plates while “C” type holds up to 10-1/2” diameter covered
plates. Specify type, if any, when ordering. Carriers will hold
plates 4-high (8C or 8P) in carts with 13” shelf spacing and
5-high (10C or 10P) in carts with 16” shelf spacing. See
table on front page for types and quantities that will fit in
each cart.
“C” carrier for
covered plates
“P” carrier for
open plates
Loading...