Cartadis CM4000 User And Technical Manual

Download

Cartadis CM4000

Multi-Coin Operated

Copy Vending Unit

User's and technical

Manual V5.0

Cartadis CM4000

Multi-Coin Operated

Copy Vending Unit

User's and technical

Manual V5.0

Cartadis is a trade mark of C.M.F. tel: (33) 1 48 77 40 60 - ANG.

User's Manual V5.0 - Cartadis CM4000

! SAFETY #

This CMF product and supplies are manufactured and certified to strict safety regulations, electromagnetic regulations and established environmental standards.

! WARNING ! #

Any unauthorised alteration, which may include the addition of new functions or connection of external devices, may impact the product certification. Please contact your CMF representative for more information.

! Warning markings

All warning instructions marked on or supplied with the product should be followed.

! Electrical supply

This product shall be operated from the type of electrical supply indicated on the product's data plate label. If you are not sure that your electrical supply meets the requirements, please consult your local power company for advice.

To disconnect all electrical power to the product, the disconnect device is the power cord. Remove the plug from the electrical outlet.

Intervention

Any installation, removing or intervention on the Cartadis unit require previously to unplug the copier or the multifunction. If not, damages may occur on the copier or on the multifunction.

! Operator accessible areas

This product has been designed to restrict operator access to safe areas only. Operator access to hazardous ares is restricted with covers or guards which would have to be removed using a tool. Never remove these covers or guards.

! Maintenance

Any operator product maintenance procedure will be described in the user documentation supplied with the product. Do not carry out any maintenance on the product which is not described in the customer documentation.

! Cleaning your product

Before cleaning this product, unplug the product from the electrical outlet. Always use materials specifically designated for this product. The use of other materials may result in poor performance and may create a hazardous situation. Do not use aerosol cleaners, they may be flammable under certain circumstances.

For more information on Environment, Health and safety in relation to this CMF product and supplies, please contact the following customer help lines: Europe : +33 1 48 77 40 60.

The CE mark applied to this product symbolises CMF's declaration of conformity with the following applicable European Union Directives as of the dates indicated:

! January 1, 1995 : Council directive 73/23/EEC, amended by Council Directive 93/ 68/EEC, approximation of the laws of the member states related to low voltage equipment.

! January 1, 1996 : Council directive 89/336/EEC, approximation of the laws of the member states related to electromagnetic compatibility.

A full declaration of conformity, defining the relevant directives and referenced standards, can be obtained from your CMF representative.

! WARNING ! #

In order to allow this equipment to operate in proximity to Industrial, Scientific and Medical (ISM) equipment, the external radiation from the ISM equipment may have to be limited or special mitigation measures taken.

T ABLE OF CONTENTS

USER'S MANUAL

1. INTRODUCTION ......................................................................

2. CM4000 and THE END USERS ................................................

3. CM4000 and THE OPERATOR .................................................

3.1. Menu organization ....................................................

3.2. Statistics ...................................................................

3.3. Price setup ................................................................

3.4. Discount price setup .................................................

3.5. Stactistics printing .....................................................

3.6. Free copies ...............................................................

TECHNICAL MANUAL

4. INSTALLATION ........................................................................

4.1. Mechanical fastening ................................................

4.2. Electrical connection .................................................

4.2.1. Connection for only one paper format

management ...................................................

4.2.2. Connection for several paper format

management ...................................................

4.3. Configuration parameters .........................................

Decimal point ....................................................

Copier pulse filter .............................................

Relay 1 or 2 opening delay ..............................

Copy credit reset ..............................................

Remaining credit reset .....................................

Processing mode of "State B" and "State C"

signals ..............................................................

Accepted coins selection ..................................

Serial number ...................................................

4.4. Installation validation procedure ..............................

5. TROUBLE-SHOOTING ..............................................................

6. TECHNICAL SPECIFICATIONS ................................................

SECTION PAGES

3 5 7

7 11 12 13 14 16

17 17 18

20 21

24 24 24 25 25 25

25 26 26 27

29 31

User's Manual V5.0 - Cartadis CM4000

INTRODUCTION

Thank you for your choosing a Cartadis CM4000 to manage your copy vending. This unit is dedicated to copy vending and thus shall be attached to a photocopier of

any brand. It vends photocopies in an unattended environment against coins, the main features

are:

- depending on the country up to 8 different coins can be accepted (see the list displayed on the front face of the unit), no back change is given,

- the end user can buy one or more copies in a first time and make copies in a second time,

- the number of available copies is displayed,

- the operator can easily set the prices and also select a subset of accepted coins,

- discount prices can be defined when a user credit reaches a certain amount,

- statistics are available to help the operator to manage the cash,

- according to the technical feasibility of the copier different copy formats or types (black and white or colours) can be sold at different prices,

- a free key copy allows the operator to make copies whithout any coin.

User's Manual V5.0 - Cartadis CM4000

Several optional items can complete the unit:

- cash box cover with lock (needed when the coins collection is done on a cash box exchange basis),

- a pedestal allows to mount the unit without mechanical connection to the photocopier,

- a portable printer allows the statistics to be printed out.

The Cartadis CM4000 is available for almost all the countries, in case new coins are issued, the unit can be upgraded at the factory or at your local Cartadis distributor.

The first part is intended to the copier operator and describes how to setup :

- copy sales prices according to their size,

- discount prices. It also explains how to display or to print statistics about the copy turnover. The second part of this manual is intended to the photocopier technician in charge of

the Cartadis CM4000 installation.

CM4000 and THE END USERS

Cartadis CM4000 shows it is ready for work by displaying:

Picture 1

F1: 0 F2: 0

Number of copies available

Shows the paper size selected

The left side of the display shows the type of the copy selected, 4 types are available: F1, F2, F3 and F4. Each one is related to a different format or type and thus a different price (see price setup in the next section).

According to the installation of your copier, it can mean:

F1 A4 size, B&W F2 A3 size, B&W F3 A4 size, colour F4 A3 size, colour

F1 A4 size, B&W F2 A4 size, colour F3 not used F4 not used

F1 A4 size, colour F2 A3 size, colour F3 not used F4 not used

User's Manual V5.0 - Cartadis CM4000

Important note:

The selected type of copy (size, black&white or colour) is managed by the Cartadis CM4000 only if this feature is made available to the unit by the copier. If the copier can print copies in different sizes or colours but does'nt supply status signals then it will not be possible to manage them differently at the CM4000 level. To know your configuration ask the technician who made the installation on your copier.

The CM4000 display can show two kinds of information:

a) copy format selected with the number of available copies (copy credit), b) current money credit.

In standby state the Cartadis CM4000 displays the number of copies available. The display switches automatically to "money credit" for 2 seconds each time a coin is inserted. This feature allows to give a feed back to the user about the coin recognition.

Regular price charging example:

Let a copy price of 0,15€ and A4 paper size selected.

CM4000 is ready

Then 3 coins of 0.10€ are inserted

Updated money credit is displayed

for 2 seconds

A coin of 0.10€ is first inserted

Money credit is displayed

for 2 seconds

The updated money credit is

displayed for 2 seconds and

the copier is enabled.

A coin of 0,05

€ is inserted

F1: 1

After 2 seconds the display switches

back to copy credit

€€

€ 0.45

After 2 seconds the display switches

back to copy credit

From this point 3 copies can be

printed either one by one

or in multi-copy mode.

The copier will be automatically locked

when the copy credit

will be exhausted.

F1: 3

F1: 0

€€

€ 0.10

€€

€ 0.15

CM4000 and THE OPERATOR

3.1 Menu organization

The operator is the person who owns the key of the door and the free key copy. He will be able to:

- set up selling prices of the copies,

- set up several discount price tables if wished,

- display or print statistics.

All these capabilities are available through the software menu. To enter the menu you have to turn the lockable free key copy. In the same way to leave the menu and switch back the CM4000 to user mode you have to remove the lockable free key copy.

Within the software menu three keys allow the operator to move from one function to an other or to enter values.

These three keys are located on the Cartadis CM4000 panel, they are labelled by:

User's Manual V5.0 - Cartadis CM4000

The meaning of keys within the menu is:

Enter in a submenu or move the cursor to the right.

Move to the next menu item or modify the blinking digit.

Leave the current menu or move the cursor to the left.

To enter in the programming menu you must get the free key copy and lock the key. The display shows:

F1: 0

€€

€------

lock the free key copy

Press to enter

at the top of the menu

The sequence of the menu is described at the next page. All the functions are divided in 5 submenus:

Stat:

Statistics submenu, manages the turnover and the number of copies done.

Print:

Issues a print out of the statistics.

Price:

Price submenu, defines the unit price of a copy.

Bonus:

Discount submenu, deals with special discount prices.

Conf:

Configuration submenu, used only at installation time by the technician.

Price

Pr F1 Pr F2 Pr F3 Pr F4

END OF MENU, SEE NEXT PAGE

nbr.F2

Cash

nbr.F3 nbr.F4

Stat

nbr.F1

Fre.F1 Fre.F2 Fre.F3 Fre.F4

turnover

Number of F1 format copies

Number of F2 format copies

Free F1 format copies

Free F2 format copies

Unit Price for F1 format copies

Unit Price for F2 format copies

Unit Price for F3 format copies

Unit Price for F4 format copies

Statistics Printing

Number of F3 format copies

Number of F4 format copies

Free F3 format copies

Free F4 format copies

CM4000 and the Operator

User's Manual V5.0 - Cartadis CM4000

delay

Relay opening delay 2

Copier pulse Filter

delay Relay opening delay 1

Decimal mode

Accepted Coins selection

Price for Bonus 1 (F1 format)

bonus

Pr b1 Nbr.b1 Pr b2 Nbr.b2

Conf

Deci Filtr delayR1

reset

Mode Coin Serial

F2 format signal Mode

delayR2

rest cleared

remaining credit reset

Number of copies for Bonus 1

Price for Bonus 2 (F1 format)

Number of copies for Bonus 2

Copy credit Reset

Serial Number

•

Volts

Memory

Always set up at 0, except other information given by technical departement

Display of the power supply

3.2 Statistics

The Cartadis CM4000 keeps in its memory 9 counters related to the copies made. These counters are not resetable and so are always relative to the date of installation. Since only 5 digits can be displayed at the same time, some counters are displayed in two stages as shown in the following example.

Cash:

turnover

This counter shows the turnover made with copies paid. The maximum value is 99,999.00. Over the maximum value the counter rolls up to 0.

Cash

: 12 934.45

means 12,934.45 €

Nbr.F1 to F4: Number of F1 to F4 format copies These counters show the number of copies paid made with the F1 to F4 formats. Their

respective maximum value is 9 999 999. Over this maximum value, these counters roll up to 0.

Fre.F1 to F4:

Free F1 to F4 format copies

These counters show the number of copies (made with the free key copy) made with the F1 to F4 formats. Their maximum value is 9 999. Over this maximum value, these counters roll up to 0.

CM4000 and the Operator

User's Manual V5.0 - Cartadis CM4000

3.3. Price setup

The Cartadis CM4000 can manage 4 formats (or types) of copies, each format being sold at a different price: Pr.F1,Pr.F2, Pr.F3 and Pr.F4. In most of cases Pr.F1 is the price of an A4 copy format.

According to the copier hardware and how the connection to CM4000 was made by the technician at installation time, it is not always possible to operate with formats F2, F3 and F4. To know if Pr.F1 to Pr.F4 are handled or if only Pr.F1 is available, ask the technician who made the CM4000 installation on your copier.

Pr F1:

Unit Price for F1 format copies

This counter shows the current price of copy made with F1 format. The maximum value is 99.99.

Price modification Once the price is displayed, it is possible to modify it. Pressing first the key allows a cursor to appear under the first digit. It is possible to modify the digit selected by the blinking cursor with the key . The digit to modify scrolls from 0 to 9 at each key in. The key allows an other digit to be selected. The key enters the modified value and returns to the menu.

0.15

select the digit to modify

0.15

0.20

modify the selected digit

Pr F1

means 0,15€

0.15

Example of price displaying

Example of price modification

enter the modified value and return to the menu

ask for cursor modification

Pr F1

Pr F2 to F4: Unit Price for F2 to F4 format copies Pr.F2 to Pr.F4 can be displayed or modified like Pr.F1. (Unit Price for F1 format copies).

In most cases Pr.F2 corresponds to an A3 copy format.

3.4. Discount price setup

The Cartadis CM4000 allows to set up 2 levels of discount prices for the format F1. These prices are entered in a price table:

1 copy Pr.F1

Nbr.b1 copies Pr.b1 Nbr.b2 copies Pr.b2

Number of copies Price

The value Pr.F1 (Unit Price for F1 format copies) is the unitary price for a F1 copy format, this one being in the menu price.

The value Nbr.b1 (Number of copies for Bonus 1) is the number of copies (bonus 1 level) got for the price of bonus 1 (Pr.b1 -

Price for Bonus 1 (F1 format)).

The value Nbr.b2 (

Number of copies for Bonus 2) is the number of copies (bonus 2 level)

got for the price of bonus 2 (Pr.b2 -

Price for Bonus 2 (F1 format)).

The values Nbr.b1 (

Number of copies for Bonus 1), Pr.b1(Price for Bonus 1 (F1 format)),

Nbr.b2 (

Number of copies for Bonus 2) and Pr.b2 (Price for Bonus 2 (F1 format)) are

located in the menu bonus. To display or modify these values you must proceed like for Pr.F1 (Unit Price for F1

format copies -

see page 11). As an example a discount table for F1 format copies could

be:

If no discount prices are requested the value 0 (default factory value) in Pr.b1 (Price

for Bonus 1 (F1 format)

)disables the discount table.

Number of copies Price (

€)

CM4000 and the Operator

1 copy 0.15 8 copies 1.00 20 copies 2.00

User's Manual V5.0 - Cartadis CM4000

Knowing the discount table of the previous page and if Pr.F2 (Unit Price for F2 format

copies

) is set to 0.30€, then the Cartadis CM4000 will compute automatically:

The CM4000 will apply the same way of computation for the F3 to F4 formats.

3.5. Statistics printing

In order to get a print out of all the statistics you have to follow the procedure:

1 copy 0.30 4 copies 1.00 10 copies 2.00

Number of copies Price (

€)

Computed discount table for F2 format

Very important rules for the discount:

The discount price is given to the user only if copies are not made in between the coins insertion.

A discount price is computed by the CM4000 for the F2 to F4 format copies. This computation is based on the ratio F1 Price to the selected format price.

Open the door and plug the printer

cable in the DIN connector

Switch on the printer power

Lock the free key copy

€€

€-----

To enter the menu

To select the print menu

To start printing

Print out example:

CM4000 and the Operator

CM4000 serial number

technical parameters

CM4000 software version

coins recognition identification table

------------------------SERIAL : 119

EURO V1.2

- Statististics CASH : NBR.F1 : NBR.F2 : NBR.F3 : NBR.F4 : FRE.F1 : FRE.F2 : FRE.F3 : FRE.F4 :

- Prices PR.F1 : PR.F2 : PR.F3 : PR.F4 :

- Bonus PR.B1 : NBR.B1 : PR.B2 : NBR.B2 :

- Coins COINS :

- Configuration FILTER : DELAY1 : DELAY2 : RESET : RESET.CL : MODE :

-------------------------

2 561.55

9 365 1 756

124 253

52 12

0.15

0.30

1.00

2.00

1.00 8

2.00

192

1 1 0

OFF

CA400 V1.6 # 8740

User's Manual V5.0 - Cartadis CM4000

DIN Printer connector pinout

The CM4000 is fitted with a lock on the top panel, the two possible positions of the key are:

Example:

3.6. Free copies

unlocked position, the key can be removed and coins have to be inserted to

make copies. locked position, the key stays in the lock and the unit is in free vending mode.

Insert and lock the free key copy

CM4000 shows it is running in

free vending mode

€€

€-----

If copies are made, the number of free copies is displayed and statistics are updated.

F1: 5

Electrical standard Bit rate number of data bits parity stop bits handshake

CTS

RxD

0 Volt

RTS

TxD

: RS232 : 1200 bits/sec : 7 : none : 2 : RTS/CST

INSTALLATION

4.1 Mechanical fastening

The Cartadis CM4000 can be mounted either directly on the copier or on its stand or mounted on the optional CM4000 pedestal.

Four holes on the back side of the Cartadis CM4000 allow to screw it on the copier.

234567890123456

23456789012345678901234567

Copier

copier stand

CM4000

Cartadis

CM4000

User's Manual V5.0 - Cartadis CM4000

ST2 ST1 Relay 1 off on (default configuration)

normally opened contact connected to the Grey wire

on o ff normally closed contact connected to the Grey wire

The optional pedestal allows to mount the Cartadis CM4000 close to the copier without mechanical action on the copier:

23456789012345678901234567

CM4000

Pedestal

If requested an optional strong steel cable is available to secure the CM4000 to the copier.

4.2 Electrical connection

The Cartadis CM4000 must be connected by a photocopier specialist. The CM4000 is "seen" by the photocopier as a key counter and has therefore to be connected like a key counter. The CM4000 has no power pack of its own, it is usually supplied from the +24V power supply of the photocopier. The photocopier can supply the +24V to the CM4000 from two possible locations:

- easiest way: the +24V is available from one pin out of the key counter connector,

- else: the +24V has to be supplied directly from the copier power supply.

The CM4000 electronic board is fitted with 3 jumpers, their meaning is:

Copier

SW1 Cartadis CM4000 power comes from: Downward (default configuration) the Yellow or White wire Upward the red wire or from an external power supply

ST3 ST4 Relay 2 off on (default configuration)

normally opened contact connected to the Purple wire

o n off normally closed contact connected to the Purple wire

Technical

CM4000 Photocopier interface

Count Down

CM4000

Power Supply

Optional +24V Power Supply

(Red*)

Yellow

White

Copier

+24V

Pulse to 0V

ST1 ST2

State B or Format 2 count down

Output signal

5V to 24 V

ST4

ST3

Typical CM4000 connection to photocopier

Grey

Yellow/

Green

To modify the default position of the jumpers you must remove the black plastic coin selector from inside the CM4000 housing. The electronic board is on the back side of the coin selector.

To locate the jumpers on the CM4000 electronic board see next page.

Installation

Dark blue

Green

State C or Format 3 count down

Relay 2

Relay 1

Copier

Enable

Format 2 mode

Ambre

Purple

Light

blue

Pink

Brown

Black

ST5

ST6

ST7

+24

ST9

ST8

SW1

User's Manual V5.0 - Cartadis CM4000

Optional +24V

counter

Printer

CM4000 board (CI4700)

CM4000 jumpers and connectors location

Display

keyboard

External +24V power supply (optional)

free key copy

If a full galvanic insulation between the Cartadis CM4000 and the photocopier is requested either by the end user or by the copier manufacturer, an optional power supply pack is available. Then this power supply has to be connected to the CM4000 internal screw connector (old model) or to the JACK connetor and the switch SW1 has to be moved upward.

Technical

Copier

ST1

ST4

ST5

ST6

ST7

ST8

ST2

ST3

ST9

SW1

Once the copier has been turned off, connect the four wires: YELLOW, WHITE, DARK BLUE, GREY to the "key counter" connector (see diagram page 19).

- Yellow wire = terminal 1 of the counter pulse

- White wire = terminal 2 of the counter pulse

- Grey wire = terminal 1 of copier enable

- Dark blue wire = terminal 2 of copier enable

- Green wire = 0 volt

- Yellow/Green wire = protective earth (PE)

4.2.1 Connection for only one paper format management

In the "One paper format" connection, format is always supposed to be "F1" and the copy price will always be "Pr.F1 (

Unit Price for F1 format copies)".

Only 6 wires need to be connected out of the 12 wires of the cable:

ST1 : Relay R1 : Contact NO ST2 : Relay R1 : Contact NC

ST3 : Relay R2 : Contact NC

ST4 : Relay R2 : Contact NO ST5 : Reserved

ST6 : Opto 2 low current

ST7 : Opto 3 low current ST8 : Reserved

ST9 : Reserved

Jumper meaning

Installation

0Volt Green wire connection:

Yellow/Green wire connection:

- This wire must be connected to the copier frame.

Once all the 6 wires are connected switching the copier on involves CM4000 to also switch on.

Particular case of CANON copiers:

These copiers do not supply +24V to the CCC connector (Card Counter Connector). Connections have to be achieved as follows:

If the 0Volt of your copier is linked to the mechanical frame, then you can connect the CM4000 Green wire to this frame for simplicity.

If the 0 Volt of your copier is not linked to the mechanical frame, which is the case for RICOH's original copiers, then you must connect the CM4000 Green wire to the 0Volt of your copier +24V supply (0Volt is generally available from one of the key counter terminals).

- White wire = +24V, copier power supply

- Yellow wire = pin 4 (0V pulse)

- Grey wire = pin 3

- Dark blue wire = pin 1

- Green wire = copier frame

- Yellow/Green wire = copier frame

Card Counter Connector

In order for the CM4000 to sense the status of the copier, 2 opto-couplors called "StateB" and "StateC" will have to be connected.

4.2.2 Connection for several paper format management

The CM4000 can manage up to 4 formats called "F1", "F2", "F3" and " F4"; each one having its own copy price. F1 to F4 are usually dealing with paper formats or Black and White or colour copies. They can mean for example:

F1 A4 size, W&B F2 A3 size, W&B F3 A4 size, colour F4 A3 size, colour

User's Manual V5.0 - Cartadis CM4000

The "StateB" and "StateC inputs define 4 possible copy formats:

The price of the chosen copy format is deducted from user's credit as soon as a pulse is received between the yellow and white wires.

The relay 1 goes to the state "ON" if the copy credit, in the chosen format copy, is different from 0.

The relay 2 goes to the state "ON" if the copy credit, in the format 2, is different from 0.

The CM4000 "mode" parameter (accessible from menu described on page 10) defines the 2 inputs "StateB" and "StateC" and their role in the format management:

This parameter may be initialized with the following values:

- 0 :

- 1 :

The 2 following tables describe in details the CM4000 behaviour for each of the 2 possible values of the "mode" parameter.

"mode = 0" parameter (default factory setting)

Technical

both "StateB" and "StateC" inputs define the format chosen on the copier. both "StateB" and "StateC" inputs cause the user's credit to be deducted

with respectively P2 and P3 prices.

EtatC

voltage between the

Pink and Light blue wires

0V 5V to 24V 5V to 24V

StateB

voltage between the

Black and Brown wires

5V to 24V

Format

F1 F2 F3 F4

Installation

In this mode, the user credit goes down of:

- one F1 copy, on receipt of a pulse between the Yellow wire and the White wire.

- one F2 copy, on receipt of a pulse between the Black wire and the Brown wire.

- one F3 copy, on receipt of a pulse between the Pink wire and the Light blue wire. The White wire and the Yellow wire are usually connected in parallel to the start

clutch for A4 format paper. As the Black wire and the Brown wire are usually connected in parallel to the start clutch for A3 format paper.

In this mode, the CM4000 is not able to know, before the copy is made, which copy format is selected on the copier. So the CM4000 "relay 1" will be ON as soon as the F1 copy credit is different from 0 and will stay ON whatever the selected format on the copier.

To prevent a F2 format copy from being made if credit is insufficient, the second CM4000 relay called "relay 2" has to be connected. This relay switches ON when the F2 copy credit is different from 0. The usual way to connect this relay is in serial with the A3 cassette sensor, so when the relay is OFF, the copier senses no A3 paper and so this copy format becomes disabled.

Depending on the technology of the cassette or paper sensor, the normally closed or normally opened contact of the "relay 2" can be used (see diagram page 19).

Relay 1 switches ON if the F1 copy credit is different from 0. Relay 2 switches ON if the F2 copy credit is different from 0.

Important note:

Do not connect the Yellow wire and the White wire to the key counter plug.

To be able to use the "mode = 0" of the CM4000, your copier must feature:

- only one pulse is sent whatever the format,

- there is a place where you can connect the state wires to sense the copier status (the polarity of these wires is of no consequence).

On most copiers, it is quite difficult to find a steady signal delivering the A3 mode. In this case, the Black wire and the Brown wire can be connected to an A3 LED terminals (even if it's a multiplexed signal) of the copier panel (if available).

"mode = 1" parameter

User's Manual V5.0 - Cartadis CM4000

4.3. Configuration parameters

In the submenu "conf" several parameters enable to adapt the CM4000 to the specific model of copier you have and to your country. To reach the wished parameter, locate it from the map of page 9.

Deci:

Decimal mode

When its value is ON, money credit is displayed with a decimal point. When its value is OFF, money credit is displayed without a decimal point. The default factory setting is ON.

Filtr: Copier pulse Filter

This parameter represents the minimum duration in milliseconds for the copier count down pulse. This parameter is adjustable between 1 and 99. It is intended to protection against pulses with bouncing at rising and falling edges. For optimal setting of this parameter, you must proceed by trial and error:

- if this parameter is set too high, CM4000 may disregard count down pulses.

- if this parameter is set too low, CM4000 will count more copies than were made.

Adjusting it to 20 milliseconds gives generally good results (default setting).

Filtr 20

to modify the selected digit

enter the modified value and return to the menu

select the digit to modify

Deci On

to modify the value

OFF

to go back to the menu

Technical

Installation

Delay 1, Delay 2: Relay 1 or 2 opening delay

This parameter enables relays 1 or 2 opening to be delayed once copy credit reaches

0. This is adjustable between 0 and 99 seconds and is useful on some copiers which do not accept relay opening upon countdown pulse, and therefore often causes paper to jam or copies not to be fully printed. The default factory setting is 1.

Reset:

Copy credit Reset

This parameter enables the user copy credit to be cleared after a time has elapsed without copies having been made. The value 0 means no reset. It's ajustable from 1 minute to 99 minutes. The default factory for this parameter is 0, so no reset is done.

Rest cleared : remaining credit reset

Once a copy has been made, in case remaining credit is lower than the smallest price (P1 to P4), the CM4000 may cancel this remaining credit.

- If "rest cleared" parameter = OFF, the CM4000 will never cancel the remaining credit.

- If "rest cleared" parameter = ON, the CM4000 will clear the remaining credit in case it is lower than the smallest price.

Example: if "rest cleared" parameter = ON and copy price is 0.15

€

- a user inserts a coin of 0,20€,

- The copy credit is 1 and money credit is 0.20

€ (displayed for few seconds),

- one copy is done, so copy credit is 0 and money credit is cleared to 0.

Mode :

processing mode of "State B" and "State C" signals

This parameter deals with copy formats. It can be set up to "0" or "1":

- 0 :

- 1 :

See page 22 and 23 to choose the right value.

means CM4000 runs in detection mode of copier status (default factory setting), means CM4000 runs in pulse mode.

User's Manual V5.0 - Cartadis CM4000Technical

Coin: Accepted Coins selection (maximum 8 different coins) This parameter deals with accepted coins, with it you can select a subset of the

recognized coins to be accepted. The value 0 means all the coins are accepted, the value 255 means no coin is accepted. Each coin has a, so called, binary weight of : 1, 2, 4, 8, 16, 32, 64 and 128.

For your country see the joined list of recognized coins and their affected binary weight.

To disable a subset of accepted coins, you have to enter a new coin value, this coin value being the sum of the binary weight of the coins to reject.

Example for France binary weight Coin

1 2,00 2 1,00 4 0,50 8 0,20 16 0,10 32 0,05 64 0,02 128 0,01

To disable the 0,01 and 0,02

€ coins, enter the value 192 (weight 128 +64).

S.Nbr:

Serial Number

This value is printed on the statistics print out and so, allows to identify the origin of the copier when several print out are coming from several CM4000. You can enter the value you want for the Serial number. The default factory setting is

192 (coins accepted : 0,05

€, 0,10€, 0,20€, 0,50€, 1€, 2€).

4.4 Installation validation procedure

To check the CM4000 for correct operation, follow the procedure:

- i

To check for coin acceptance without affecting the statistics you have to press the key of the panel, then keeping this key pressed insert a coin. The coin value is displayed, the coin is not stored in the cash box but rejected

Besides, if you wish to quickly clear the copy credit without making any copy, you must press the Reject coin button. Then keeping it pressed, unlock the free key copy. In this case the "Cash" counter is nevertheless affected by the coins inserted.

insert at least one coin of each type to check for acceptance and rejection according to the parameter "coin" (see page 26). Check the money credit after each coin insertion, check the copy credit with each allowed copy format, make a copy of each allowed copy format and check the copy credit after count down, check the "Delay" parameter for correct adjustment doing as follows:

1 - insert enough money to get at least 3 copies, 2 - set the copier for multi copies with 10 copies, strike the key COPY on the

copier,

3 - check the number of copies you got is in accordance with the initial credit.

Installation

User's Manual V5.0 - Cartadis CM4000

Technical

TROUBLE SHOOTING

The user got more copies than he paid in multi copies

Try to reduce the value of the "Delay" parameter. If the problem is still there that means the copier sends the copy pulse at the end of the copier copy cycle. The only solution is to get a pulse earlier in the copy cycle, for example by connecting the yellow and white wires in parallel with the start paper clutch, or the synchronization clutch in case there are several cassettes.

Err 1 or Err 4 The CM4000 is out of order and the coin mechanism has to be replaced.

Err 2

The statistics memory is corrupted, ask to your local dealer, he will give you the procedure to clear this error.

Err 3

This error code is displayed for 10 seconds if the accepted coin doesn't reach the cash box within a certain elapse time. That could mean the coin desk is dirty and need to be cleaned or the cash box is full.

User's Manual V5.0 - Cartadis CM4000

Coins are often rejected

Clean the coin desk:

- open the CM4000 door,

- open the selector door, you have to remove the top plastic part by unscrewing the black screw,

- clean the inner parts corresponding to the coin desk,

- rescrew the top plastic part.

If the coins acceptance has not been improved, contact your local distributor.

Two inner faces of the coin desk to clean

CM4000 coin selector

Top part to remove in order to open the door

Technical

TECHNICAL SPECIFICATIONS

TYPE

FUNCTION

ELECTRONICS

MEMORY

OPERATING CONDITIONS

Moisture Temperature

USE

DIMENSIONS

WEIGHT

POWER SUPPLY

POWER CONSUMPTION

CM4000

Multi-coin operated copy vending unit Very large scale integrated 32 bits microcontroller EEPROM for parameters and statistics backup

20% - 90% RH 10 - 40°C

Indoors only 280mm (W) x 380mm (H) x 100mm (D)

7.5 kg (empty) 24V DC 100 mA idle state

500mA for 0.5 sec. at coin insertion

User's Manual V5.0 - Cartadis CM4000

COUNTER CAPACITIES

User copy credit User money credit

Statistics:

Turnover Format 1 Format 2 Free Format 1 Free Format 2

MANUFACTURER

not limited max 1 000.00

Max 99 999,00 (overflow round up to 0) Max 9 999 999 (overflow round up to 0) Max 9 999 999 (overflow round up to 0) Max 9 999 (overflow round up to 0) Max 9 999 (overflow round up to 0)

C.M.F. Fontenay-sous-Bois FRANCE phone: (33) 1 48 77 40 60

Technical

Cartadis CM4000 User And Technical Manual

Specifications and Main Features

Frequently Asked Questions

User Manual