Carson 28V, 14V User Manual

PAPA

MANMAN WAILWAIL YELPYELP

SIRENSIREN

WSWS--295295

ONON OFFOFF

Carson

MANUFACTURING COMPANY, INC.

CARSON MANUFACTURING CO., INC.

5451 NORTH RURAL STREET

INDIANAPOLIS, IN 46220

[phone] www.carsonsirens.com

TECHNICAL BULLETIN

TWO TONETWO TONE

P.A. VOLUMEP.A. VOLUME

RADIORADIO

INSTALLATION AND

OPERATING MANUAL

WS-295-53 14V
WS-295-53 28V

WS-295-53 PG (Positive GND)

Sound Hazard - Sound level from siren speaker (>120dBA @ 10 feet) may cause hearing damage.

Do not operate siren without adequate hearing protection for you and anyone in immediate vicinity.

(Ref. OSHA 1910.95 for occupational noise exposure guidelines)

TB0326B Page 1 of 8 10/18/03

WS-295-53 SPECIFICATIONS

INPUT POWER: 11-16 Volts DC, 8 Amps DC per 100W Speaker (WS-295-53 14,PG)
22-32 Volts DC, 4 Amps DC per 100W Speaker (WS-295-53 28)

SIREN MODE
OUTPUT POWER: 15 VDC input, 100W speaker(s) (WS-295-53 14,PG)

30 VDC input, 100W speaker(s) (WS-295-53 28)

One speaker - 105 Watts RMS
Two speakers - 180 Watts RMS
Rating not available for 58W or 80W speakers

AUDIO MODE
OUTPUT POWER: 14 VDC input, 100W speaker(s) (WS-295-53 14,PG)

28 VDC input, 100W speaker(s) (WS-295-53 28)

One speaker - 40 Watts RMS
Two speakers - 80 Watts RMS
Rating not available for 58W or 80W speakers

SIREN
FREQUENCY: 600Hz - 1350Hz Nominal TWO-TONE - 450Hz and 600Hz

CYCLE RATES: WAIL - 14 cycles/min

YELP - 190 cycles/min
TWO-TONE - 1 cycle/min

AUDIO
RESPONSE: 200Hz - 10KHz +/-3db

Harmonic Distortion Less than 3% @ 1KHz (WS-295-53 14,PG)
Harmonic Distortion Less than 7% @ 1KHz (WS-295-53 28)

RADIO INPUT
SENSITIVITY: 0.75VAC Input Min. for 40 Watts RMS Output (1 spkr)

OPERATING
TEMPERATURE: -15° F to +140° F

SIZE: 6" Wide X 2-3/8" High X 6-1/4" Deep
WEIGHT: 4 pounds
NIGHT VISIBILITY: Pilot light in siren pushbutton when power is on
PROTECTION: High Voltage – Siren output stops with input voltage above highest rating

Stops high output power from blowing speaker

Reverse Polarity - Fuse blows when power is wired backwards

Shorted Output – Fuse blows if speaker shorts (a common problem)

NOTICE

Due to continuous product improvements, we must reserve the right to change any specifications and information,
contained in this manual at any time without notice.
Carson Manufacturing Co., Inc. makes no warranty of any kind with regard to this manual, including, but not limited to,
the implied warranties of merchantability and fitness for a particular purpose.
Carson Manufacturing Co., Inc. shall not be liable for errors contained herein or for incidental or consequential
damages in connection with the furnishing, performance, or use of this manual.

TB0326B Page 2 of 8 10/18/03

INSTALLATION

Bolt must not pass through

Proper installation of the unit is essential for years of safe, reliable operation. Please read all instruction before
installing the unit. Failure to follow these instructions can cause serious damage to the unit or vehicle and may void
warranties.

SAFETY PRECAUTIONS

For the safety of the installer, vehicle operator, passengers and the community please observe the following safety
precautions. Failure to follow all safety precautions and instructions may result in property damage, injury or

death.
Qualifications - The installer must have a firm knowledge of basic electricity, vehicle electrical systems and

emergency equipment.
Sound Hazard - Sound level from siren speaker (>120dBA @ 10 feet) may cause hearing damage.

Do not operate siren without adequate hearing protection for you and anyone in immediate vicinity.

(Ref. OSHA 1910.95 for occupational noise exposure guidelines)
Mounting - Mount the unit for easy access by the vehicle operator. DO NOT mount in air bag deployment area.

Assure clearances before drilling in vehicle. To prevent internal damage mounting bolts must not enter case more
than 1/4".
Wiring - Use wiring capable of handling the current required. Make sure all connections are tight. Route wiring to
prevent wear, overheating and interference with air bag deployment. Install and check all wiring before connection to
vehicle battery.
Testing - Test all siren functions after installation to assure proper operation. Test vehicle operation to assure no
damage to vehicle.
Keep These Instructions - Keep these instructions in the vehicle or other safe place for future reference. Advise
the vehicle operator of the location.

MOUNTING

The mounting bracket supplied can be installed above or below the unit. Choose a mounting location convenient to
the operator and away from any air bag deployment areas. Inspect behind mounting area for clearance. Assure
adequate ventilation to prevent overheating. Consider wire routing and access to connections, as well as
microphone bracket placement. Install mounting bracket to vehicle using 1/4" hardware (not supplied).
If mounting in a rack or console, make sure that mounting bolts do not enter case more than 1/4".

May need to set RADIO VOLUME ADJUST inside the unit before final mounting and installation
A microphone clip along with mounting screws (CP3633) holds the microphone in place.

TB0326B Page 3 of 8 10/18/03

CP3571 Mounting Bracket

1/4-20 Bolt
(CP3966)

cover more than 1/4”