Last updated: 2011.08.18Last updated: 2011.08.18
Car-Solutions.com
Model : Model : QVLQVL--E65E65--V2 V2 / Product code : / Product code : BMBM--09010901--652652
Video Interface for BMW E65
Specification & InstallationSpecification & Installation
Compatible with BMW 7 Series(E65/66)
www.car-solutions.com
support@car-solutions.com
Contents
Car-Solutions.com
1. Before installation
1.1 Main specification
1.2 Features
1.3 System diagram
1.4 Components
1.5 Exterior
1.6 POWER cable
2. Setup
2.1 DIP switch
2.2 Keypad usage
2.3 Remote control usage
2.4 Factory mode
2.5 OSD (on screen display)
2.6 Parking guide line
2.7 BMW Handle button NAVI setting
2.8 FMTX Frequency Setting
3. Installation
3
4
5
6
7
8
9
11
12
13
14
15
16
17
3.1 Cautions on installation
3.2 CAN Installation
3.3 Installation
4. Troubleshooting
www.car-solutions.com
18
19
20
21
2
1.1 Main specification
Car-Solutions.com
1. Input Spec. (MULTI VIDEO INTERFACE)
-. 1 x Analog R,G,B (Sync on Green)
-. 1 x CVBS(REAR CAMERA) Input. (Rear camera source)
- 3 x A/V (NTST & PAL) Input.
-. 1 x LCD Input (Car system Input)
2. Output Spec.
-. 2 X CVBS OUTPUT (Video Out for installing Headrest monitor)
-. 1 x Audio OUTPUT
-. 1 X LCD OUTPUT(LCD Operation)
3. Electric Power Consumption
- Input Power : 8VDC ~ 24VDC
- Consumption Power : 12WATT, Max
4. Switching Mode (AV source)
- Possible to skip AV source while switching Mode (AV source) by DIP S/W
(Refer to the DIP S/W page)
- By ‘SET’ button of the OSD Keypad
- By Toggle Switch (Option)
- By ‘Menu’ button of the car through CAN
※ This function may not support E65 old version which is without “Menu button”
www.car-solutions.com
3
1.2 Features
Car-Solutions.com
- FMTX Module is added in the product. (No need additional FMTX
Module for Audio)
- Offering OSD Key Pad
(The remote control is not offered anymore)
- Possible to move the displayed position of Navi (Only on RGB mode)
- Changed OSD MENU
www.car-solutions.com
4
1.3 System diagram
Car-Solutions.com
NAVIGATION Input
(Analog RGB)
A/V 1
A/V 2
A/V 3
CVBS IN
(Rear camera)
Car Screen Input
(CAR MAIN BOARD)
OSD Keypad
VIDEO
CIRCUIT
POWER
CIRCUIT
Switch for source toggle
MCU
VIDEO MUX
FMTX
OEM NAVI Button (Can Interface)
DISPLAY
A/V OUT
(Video out 2
Audio L, R1)
Car Installation
OEM LCD
HEADREST
MONITOR
Power Input
(+8VDC ~ +18VDC)
Dip S/W
Rear Camera
www.car-solutions.com
5
1.4 Components
Car-Solutions.com
IR cable (8P) * 1ea
Remote control * 1ea
OR
Ground cable * 1ea
Keypad * 1ea
CAN cable * 1ea
FPC cable * 1ea
FFC cable (50P) * 1ea
MODE cable * 1ea
RGB cable * 1ea
www.car-solutions.com
POWER cable (6P) * 1eaAV cable * 1ea
6
1.5 Exterior
Car-Solutions.com
⑦ ⑧ ⑨
Dimension
Horizontal length 149mm
Vertical length 91mm
Height 19mm
① DIP switch
② LED
③ MODE
④ RBG IN
⑤ A/V(IN/OUT)
⑥ POWER
⑦ KEYPAD
⑧ LCD IN/OUT
⑨ CAN I/F
① ② ③ ④ ⑤ ⑥
www.car-solutions.com
7
1.6 POWER cable
Car-Solutions.com
FILTER
& FUSE BOX
Gray
파란색
주황색
FMTX
I - DRV
검정색
GND
Blue
Orange
Red
Black
990mm
빨강색
회색
990mm
www.car-solutions.com
ACC
LAMP - RV
8
2.1 DIP switch
Car-Solutions.com
※ ON : DOWN / OFF : UP
#PIN FUNCTION DIP S/W Selection
1 RGB INPUT MUTE
2 A/V 1 MUTE
3 A/V 2 MUTE
4 A/V 3 MUTE
5 To select monitor size
6 N.C
7 Rear Mode
8
ON : Skipping RGB Mode
OFF : RGB Display
ON : Skipping A/V 1
OFF : A/V1 Display
ON : Skipping A/V 2
OFF : A/V2 Display
ON : Skipping A/V 3
OFF : A/V3 Display
ON : 6.5” LCD Setting
OFF : 8.8” LCD Setting
ON : External Rear Camera
OFF : OEM Rear Camera
N.C
www.car-solutions.com
9
2.1 DIP switch
Car-Solutions.com
#PIN
Type of monitor
E65 8.8” OFF
E65 6.5” ON
※DIP S/W Use Example
[BMW E65-6.5 Inch]
-. Use Input Mode : A/V3(DVD), Navigation (RGB)
-. Rear Camera : When to be installed on CVBS 4
▷ DIP S/W : 1 OFF
▷ DIP S/W : 2,3 ON
(INPUT MODE SKIP)
▷ DIP S/W : 4 OFF (enable A/V3)
▷ DIP S/W : 5 ON (6.5 Inch)
▷ DIP S/W : 6 OFF
▷ DIP S/W : 7 ON (enable CVBS4)
▷ DIP S/W : 8 OFF
5
[E65 8.8 Inch]
[E65 6.5 Inch]
www.car-solutions.com
10
2.2 Keypad usage
Car-Solutions.com
Select one between the remote controller and the keypad
FACTORY MODE (Interface setting) :
Press these buttons on OSD keypad in the following sequence; UP→DOWN→UP →MENU
KeyKey FunctionFunction
MENU/EXIT Activating OSD menu and Getting back to the previous state after setting mode
SEL/INPUT Making a selection and hanging modes
UP
DOWN
Moving leftward or upward (If you press this button 2 seconds long, you can get access
to HOT KEY function.)
Moving rightward or downward (IF you press this button 2 seconds long, you can reset
all data.)
www.car-solutions.com
11
2.3 Remote control usage
Car-Solutions.com
KeyKey FunctionFunction
POWER & PIP Unavailable
MENU Activating OSD menu
OK Making a selection, changing image display
Moving upward
▲
▼ Moving downward
◀
(If you press this button 2 seconds long, “Hot key” function will
activate/ deactivate.)
Moving leftward
(If you press this button 2 seconds long, you can get access to the
factory mode.)
Moving rightward
▶
What is Hot Key function ?
You can use this function via pressing number “1” button next to the radio button. You can change audio source to the external
AUX with this function. (original function of BMW) Our device let it change to an external video source for driver to use this
function via this button. So, you can change sources (audio<->video) by pressing this button without any other install process.
(If you press this button 2 seconds long, you can reset all the data
about user environment.)
www.car-solutions.com
12
2.4 FACTORY mode
Car-Solutions.com
FACTORY mode : Operated with pressing UP->DOWN->UP->MENU keys on the keypad in sequent or
Press ◀ button 2 seconds long on the remote control.
POSITION
– H-POSITION : moving in horizontal direction
- V-POSITION : moving in vertical direction
FM-TX
- FM-TX USE : Set up for FMTX
- FREQUENCY : FMTX Frequency Setting.
(Refer to the next ‘FMTX frequency setting’ page)
www.car-solutions.com
I-DRV
–To control DVD, Navi by I-DRV (Optional)
Refer to the “BMW Handle button NAVI setting” page.
REAR-CAM
- By Rear Wire : When to install Back-up Cam by rear wire of
power cable (Same with previous version)
- By CAN-BUS : When to install Back-up Cam by CAN wiring.
When the car is in reverse, the CAM is detected automatically.
13
2.5 OSD (on screen display)
Car-Solutions.com
Analog RGB Mode
Analog RGB Mode
Video mode
Video mode
COLOR
-BRIGHTNESS
-CONTRAST
-RED
-GREEN
-BLUE
-COLOR BOX : Selecting one
among 3 color options
-SATURATION
-SHARPNESS
OPTION
-OSD H_POS
: Move of OSD window to Left, Right
-OSD V_POS
: Move of OSD window to Up, Down
- OSD TRANS
: OSD window transparency setting
- SCREEN MODE
: Screen Rate setting (4:3, 16:9)
- INITIAL : Initializing OSD setting
value
www.car-solutions.com
14
2.6 Parking guide line
Car-Solutions.com
Factory Default : DISPLAY - DISABLE
① When the car is in reverse, if
press ‘UP’ key for 2 sec, the
guide line appears on the screen.
② If you need to move the line
position, press ‘SEL’ key on
the above step.
(Use ‘Up’, ‘Down’ Key of Keypad)
③ On step no.2, once press “SEL”
key again, you can move the
line vertically by “UP”, “Down”
keys.
www.car-solutions.com
15
2.7 BMW Handle Button NAVI setting
Car-Solutions.com
Oversea
After implementing FACTORY MODE
(Interface setting), select I-DRV and press the
Sel button of Keypad, and then Navi Setting
window is displayed as shown right.
After selecting the one among RGB, AV1~3,
press the Sel button of keypad.
(It is fine to select any channel, because the
selecting of RGB, AV1~3 is useless. But, the
channel selected on this step will be
exempted on next channel selecting step.)
※This function is not supported at domestic NAVI, but this setting is necessary for implementation of Domestic DMB.
Domestic
When the above steps is finished, the
window is displayed as shown left. ARION,
NET-770, ML-100S, ML-740T are Domestic
DMB model. Select the model you want to
use, after that select the channel of RGB,
AV1~3.
(The channel selected on the above steps
is exempted.)
NET-770 (DMB model) is designated AV1
as shown right.
※When DVD-IR (Black) wire of RGB-IN cable is connected to IR input wire of DMB, able to operate via handle buttons.
www.car-solutions.com
16
2.8 FMTX
Car-Solutions.com
Factory Default : FMTX USE – ON, FREQENCY – 87.5MHz
Frequency Setting
Get the Factory Mode Operated with pressing UP->DOWN-
>UP->MENU keys of the keypad in sequent.
Set “FM-TX USE” to “ON” as shown left. (‘ON’ is Default).
Control the frequency by “UP”, “Down” keys.
At the bottom, you can see present frequency and control it
from 87.5MHZ to 108MHZ. (1MHZ per each time to press)
※If you do not want this function, should set “FM-TX USE” to “OFF”
www.car-solutions.com
17
3.1 Cautions on installation
Car-Solutions.com
Ignition key should be taken off before starting installation, interface power connection must be
the last step in installation.
Power cable should be separated when connecting interface.
Should be no any electronic devices or magnetic pole around installation place.
All steps of installation should be done by well-trained specialist.
Dismantling without manufacturer’s permission can not be guaranteed, (No permission to break
attached label on the board.)
Kindly check all parts are in the box, when receiving the product, if anything missing, inform to the
supplier or manufacturer.
According to our sales policy, any problems caused by user’s mistake, careless can not be
guaranteed.
www.car-solutions.com
18
3.2 CAN Installation
Car-Solutions.com
E65 CAN Wiring Diagram
Orange: CAN HIGH
Green: CAN LOW
www.car-solutions.com
19
3.3 Installation
Car-Solutions.com
1. Connect the FFC cable to FPC cable as
shown above.
3. Connect the LVDS cable of head unit to
FPC cable as shown above.
www.car-solutions.com
2. Connect the FFC cable to the LCD-IN/OUT
connector of the board as shown above.
4. Connect the FPC cable to the connector of
head unit as shown above.
20
4. Troubleshooting
Car-Solutions.com
Q. I can not switch A/V sources
A. Check IR or Ground cable connection. Check LED lamps in the interface, if it is not on, check power cable.
Q. All I got on the screen is black.
A. Check second LED lamp of the interface is on, if not, check A/V sources connected are working well. (Second lamp indicates AV sources
connected works well.) Check interface connection has been done well.
Q. Displayed image color is not proper (too dim or not suitable color)
A. Try to select “INITIAL” in OSD menu, if it does not work, inform to manufacturer.)
Q. I can watch the rear camera on the screen
A. Set the DIP switch #7 as state “ON”.
Q. Unwanted A/V mode is displayed. (A/V source switching order : OEM->RGB->AV1->AV2->AV3)
A. Check DIP Switch Setting.
Q. OEM image is not displayed.
A. Check interface’s LCD In/Out cable connection. If the status keeps on, inform to manufacturer.
Q. Screen only displays white color.
A. Check LCD out cable is connected well, if this status keeps, inform to manufacturer.
Q. After setting PIP function, I got only half OEM image at the right in the screen.
A. This is not an error, just caused by user’s setting mistake, user should set to
“Split Screen” in the OEM menu.
Q. Rear CAM does not appear, when car is in reverse after CAN wiring.
A. Operate “FACTORY MODE” like left picture, then select “UTIL Rear Select” If it is set as “LAMP”, change it to “CAN” by remote or keypad.
※ LAMP : In case of connecting “Rear-C” wire of Power Cable to Rear Lamp in vehicle.
CAN : In case of detecting Rear Cam thru CAN signal. (CAN must be wired)
Q. After moving gear to “P” or “D” from “Reverse”, I can’t get navigation, but half PDC Image in the screen.
A. Once, you starts driving, the screen displays navigation right away, this is not an system error.
www.car-solutions.com
21
Loading...