Car Solutions
release date :
model : QVI-LVTX-1CH-V6 / product code : LVTX-
2012.03.30
1CH-1201-003
Car Video Interface for
Volkswagen with RCD550
Manual
2
Contents
Car Solutions
1. Before installation
2. SETUP
1.1 Main specification
1.2 Features
1.3 System diagram
1.4 Components
1.5 Exterior
2.1 DIP switch
2.2 Remote control
2.3 Original buttons in car
2.4 OSD implementation 11
2.5 OSD (on screen display) 12
2.6 FACTORY mode 13
2.7 Rear view parking guide line
2.8 Touch calibration
2.9 Remote controller button
2.10 DVD, DTV model selection
8
9
14
15
3
4
5
6
7
10
16
18
3. Troubleshooting
19
3
1.1 Main specification
Car Solutions
1. Input Spec. (MULTI VIDEO INTERFACE)
- 1 x Analog R, G, B, C sync
- 1 x CVBS(REAR CAMERA) Input. (Rear camera source)
- 3 x A/V (NTST & PAL) Input.
- 1 x LCD Input (Car system Input)
2. Output Spec.
- 2 X CVBS OUTPUT (Video Out for installing Headrest monitor)
- 1 x Audio OUTPUT
- 1 X LCD OUTPUT(LCD Operation)
3. Power Spec.
- Input Power : 8VDC ~ 18VDC
- Consumption Power : 4WATT (in maximum level)
4. Mode change
- Input Video skip : able to skip each input source via adjusting DIP switch
- Control by using the remote control
- Able to change a mode to another mode by using the mode switch
- A
ble to change modes and control DVD, DTV via touching the screen
- Able to change modes via using the original buttons(navigation)
4
1.2 Features
Car Solutions
DVD, DTV and navigation are controlled via touching screen
DVD, DTV are controlled via registering values of the buttons on the remote controller
(only for models including remote controller)
Control of position of the DVD, navigation image
Mode change via mode switch
5
1.3 System diagram
Car Solutions
RGB Touch Input
Remote Control
Switch for source toggle
OEM Button (Can Signal)
A/V1
A/V2
A/V3
MCU
LCD
In/Out
VIDEO
CIRCUIT
POWER
CIRCUIT
VIDEO MUX
TOUCH
A/V
OUT
HEADREST
MONITOR
RGB Input
CVBS
(Rear Camera)
DVD
DTV
NAVI
Power Input
(+8VDC~+18VDC)
DIP S/W
1.4 Components
6
Car Solutions
TOUCH OUT cable * 1ea
IR cable *
(HIRCAB0002)
MODE cable *
(HARETC0001)
RGB cable *
(HNAVIC0004)
POWER cable (24P) * 1ea
(HAVCAB0002)
1ea
1ea
1ea
(HPOWER0011) (HARETC0002)
(HTOUCH0004)
REAR CAMERA POWER cable * 1ea
LVDS cable* 1ea
(HLVDSC0018)
Remote control *
(REMOTE0001)
AV cable * 1ea
SUB BOARD* 1EA
(QCPASS0284)
FFC cable(SMALL)*1ea
(FFCABL0013)
1ea
FFC
cable(BIG)*1ea
(FFCABL0012)
7
1.5 Exterior
Car Solutions
⑦ ⑥ ⑤
- SUB BOARD -
Dimension
① ② ③ ④
Horizontal length
Vertical length 91mm
Height
① LED
② POWER/CAN/RGB
③ Rear camera
④ AV(IN/OUT)
⑤ LVDS OUT
⑥ TOUCH OUT TO NAVI
⑦ DIP S/W
27mm
147mm
⑧
⑩
⑧ FROM LCD PANEL
⑨ TO CAR SYSTEM
⑩ LVDS INPUT
⑪ TOUCH OUT
⑫ TOUCH IN
⑪
⑫
⑨
2.1 DIP switch
8
Car Solutions
#PIN function DIP S/W selection
1
2
RGB INPUT skip
A/V 1 skip
ON : Skipping RGB Mode
OFF : RGB Display
ON : Skipping A/V 1
OFF : A/V1 Display
3
4
5
A/V 2 skip
A/V 3 skip
ON : Skipping A/V 2
OFF : A/V2 Display
ON : Skipping A/V 3
OFF : A/V3 Display
N.C
※ ON : DOWN, OFF : UP
※ DIP S/W usage
- Input mode to intend to use
: A/V3(DVD), Navigation (RGB)
- Rear view camera : installation on CVBS4
- When the original navigation is NOT installed
▷ DIP S/W : 1
▷ DIP S/W : 2,3
▷ DIP S/W : 4
▷ DIP S/W : 7
OFF
ON (input mode skip)
OFF (A/V3 available)
ON (CVBS4 available)
6
7
8
Rear Mode
ON : External Rear Camera
OFF : OEM Rear Camera
N.C
9
2.2 Remote control
Car Solutions
Key
POWER & PIP
MENU
OK
▲
▼
◀
▶
Function
Not for use
OSD implementation
Making a selection
Move upward
Move downward
Move leftward, press 2 seconds long-Factory
mode implementation
Move rightward, press 2 seconds long-Factory
Mode implementation-Factory mode Reset
10
2.3 Original buttons in car
Car Solutions
Mode change
If there is the “receiver” button in car and
CAN wire is connected, driver can change
modes with the “receiver” button.
Press long : mode change
Press short : return to main image
※ Connect the 9 pin of the original power cable to Can-High,
the 10 pin of the original power cable to Can-Low
11
Car Solutions
2.4 OSD implementation
OSD implementation - DVD
To implement DVD OSD menu, installer must install DVD system on AV1 and connect “IR-AV1” cable among power cables with remote
sensor cable of DVD.
>
OSD implementation - DTV, NAVI
DVD, DTV, navigation menu is available in English or Chinese. After implementing OSD menu with pushing “MENU” button on remote
controller, choose the language that you want to use. In DTV case, connect remote control cable to “IR-AV2” of power cable.
>>>
As shown above, if you touch the screen on mode ”AV2”, you can
see the menu as shown left. And then if you do NOT touch anything
on the screen 5 seconds or more long; or if you touch the screen
except the menu, the menu will disappear.(left picture)
Here is a picture of the mode change menu. If you select the
channel which you want, then the channel will be changed to
that.(right picture)
First of all, if you touch the screen on mode ”AV1”,
you can see the menu as shown left. And then if
you do NOT touch anything on the screen 5
seconds or more long; or if you touch the screen
except the menu, the menu will disappear.
At that time, if you choose “INPUT”, you can get
out of the menu and see the mode change men
u.(left picture)
Here is a picture of the mode change menu. If
you select the channel which you want, then the
channel will be changed to that.(right picture)
12
Car Solutions
2.5 OSD (on screen display)
OSD menu: Press ”MENU” button on the remote controller.
Analog RGB
Video
IMAGE
- BRIGHTNESS
- CONTRAST
- SATURATION
- HUE
- SHARPNESS
- USER IMAGE : To choose a option
among 4 prepared color shade.
Analog RGB
Video
OSD
- LANGUAGE : To change the language
displaying on navigation, DVD, DTV OSD
menu (select 1 among English or Chinese)
- TRANS : Transparency control of the OSD
background
- H_POSITION : Horizontal movement of the
OSD window
- V_POSITION : Vertical movement of the
OSD window
Analog RGB
Video
UTIL
- FACTORY RESET : To reset all the
values about navigation, DVD screen to
factory default. (NOT available for reset
of the position value of images, only for
functions inside OSD menu)
13
2.6 Factory mode
Car Solutions
Factory mode: press ◀ button 2 seconds long.
IMAGE
- H-POSITION : Control over horizontal movement of screen
- V-POSITION : Control over vertical movement of the screen
- NAVI MODEL : DEFAULT, KD900(WVGA), MD7000(WVGA),MYVI(WVGA),PAPAGO(WVGA)
- AVOUT SELECT : DEFAULT, AV1, AV2, AV3
PARK
- PARK ENABLE : Setup of rear view parking guide line
- PARK SETUP : Control over position of rear view parking guide line (Refer to
page14.)
- SAFE ENABLE : To select whether to use SAFE function(NOT to allow watch video
while driving) or
UTIL
- CALIBRATION : Touch calibration (Refer to page15.)
- IR MEMORY : To register value of buttons on the remote controller (Refer to
page16~17.)
- DVD TYPE : Setup for the type of DVD (Refer to page18.)
- DTV TYPE : Setup for the type of DTV (Refer to page18.)
- TOUCH ENABLE : Set up touch
- F
not
enable.
ACTORY RESET : To reset all the value in factory mode
14
2.7 Rear view parking guide line
Car Solutions
Factory mode: press ◀ button 2 seconds long.
① Register the value needed on the “PARK ENABLE” as “ON” in the PARK
section as shown left. (default – ON)
② If you get rear gear after setup, parking guide line will appear on screen as
shown left. Now that you push “OK” button, you can see “H-POS” on the left
of screen. Then adjust horizontal position of the guide line.
③ After adjusting horizontal position, press “OK” on the remote controller.
Then you can see “V-POS” on the left of screen. At that time you can adjust
vertical position of the guide line.
15
Car Solutions
2.8 Touch calibration
① First of all, press ◀ button on remote controller 2
seconds long. Then you can access to the FACTORY mode.
② Register “YES” when the CALIBRATION option is
selected as shown above.
>>>
③ Then you can see “touch calibration” on
screen about 2 seconds long as shown above.
After the word “touch calibration” disappear,
touch calibration function will implement. (Just
touch “┼” shape on screen.)
If you succeed, you can see “success”. If not, you
will see “failure”.
2.9.1 Remote controller button
16
Car Solutions
Registering value of remote controller buttons?
When you want to control DVD and DTV via touch screen (using OSD menu) with other models besides already
registered option-SANYO and NECVOX, you can register value of DVD and DTV’ s remote controller which you have.
Then you can control DVD and DTV via touch screen.
① First of all, press ◀ button on remote controller 2
seconds long. Then you can access to the FACTORY
mode. And go to IR MEMORY, UTIL.
There are two options in IR MEMORY as shown above;
DTV and DVD.
Then you select AV source that you want to set among
them.
>>>
② This is a window for register of DVD’ s remote
controller button value. At the moment just select a
menu that you want to save.
(Select “DTV in options of IR MEMORY” if you want to
save values of DTV’ s remote controller. And follow the
instruction below.)
Instruction>
a. Select “POWER” in OSD menu, then press “OK” on
remote controller. (as shown above)
b. If the marked area flickers as shown above, press
“POWER” button on the remote controller of DVD that
you want to use. (continued in the next page)
17
2.9.2 Remote controller button
Car Solutions
Instruction> continued…
c. The values that you registered will appear as green
text in the marked area on pressing the button. And the
values will be saved automatically.
d. Register remain buttons’ value in OSD menu like the
above-mentioned.
>>>
③ After register, select “INPUT” in OSD menu and
press “OK”. Then you can see confirmation window as
shown above. At the moment, if you choose “YES”, all
the values that you entered will be saved.
If you select “NO”, the values won’t be saved.
(If data is saved, DVD TYPE and DTV TYPE will be
changed to “USER” automatically.)
If you see “SUCCESS” on screen, the data is saved
clearly and you can control DVD via touch screen. BUT,
you MUST change the option in
DVD(DTV)/UTIL/FACTORY to “USER”. (Refer to page18.)
18
Car Solutions
2.10 DVD, DTV model selection
Factory Default : DVD TYPE – NECVOX/SANYO (For Chinese DVD)
DTV TYPE – CMMB (For Chinese DTV)
DVD TYPE
DTV TYPE
UTIL – DVD/DTV TYPE
If DVD/DTV type that you want to use is not NECVOX or SANYO, you have to register values of the remote controller
that you want to use in the “IR MEMORY” section and set the “DVD TYPE”/”DTV TYPE” to “USER”.
Unless you do this process after saving the data, you can NOT control DVD/DTV via touch screen.
DVD TYPE : NEC/SANYO, DV-108, SANYO-1, SANYO-2, USER
DTV TYPE : PIONEER/PANASONIC, USER, CMMB
※ If you enter data in ”IR MEMORY” section in FACTORY mode, “DVD TYPE”/ “DTV TYPE” will
automatically
be saved to “USER”.
19
Car Solutions
3. Troubleshooting
Q. I can not switch A/V sources.
A. Check IR or Ground cable connection. Check LED lamps in the interface, if it is not on, check power cable.
Q. All I got on the screen is black.
A. Check second LED lamp of the interface is on, if not, check A/V sources connected are working well.
(Second lamp indicates AV sources connected works well.) Check interface connection has been done well.
Q. Displayed image color is not proper. (too dim or not suitable color)
A. Try to select “INITIAL” in OSD menu, if it does not work, inform the manufacturer.)
Q. Rear camera image does NOT appear.
A. Set DIP switch #7 in “ON”
Q. Unwanted A/V mode is displayed. (A/V source switching order : OEM->RGB->AV1->AV2->AV3)
A. Check DIP Switch Setting.
Q. OEM image is not displayed.
A. Check interface’s LCD In/Out cable connection. If the status keeps on, inform the manufacturer.
Q. Screen only displays white like left picture.
A. Check LCD out cable is connected well, if this status keeps, inform the manufacturer.
Loading...