model : PI P-RGB-HE-STD-V5 / pr oduct code : PI P-RG-0810-861
www.car-solutions.com
support@car-solutions.com
model : PI P-RGB-HE-STD-V5 / pr oduct code : PI P-RG-0810-861
Video Interface for
Merecedes-Benz W211
User Guide
1.1 Features
www.car-solutions.com
support@car-solutions.com
-. POP(Picture On Picture) Function (Only available on navigation mode)
-. Auto detection for NTSC & PAL&SECOM signals.
-. Parking Guide Line function added
-. “Sync On Green” supported (Auto detection)
-. Able to change modes via mode switch
-. Able to change modes via using the original buttons
(Soldering point will be different depending on car models)
-. OSD Menu added (Controlled by Remote control)
2
1.2 Main Specification
www.car-solutions.com
support@car-solutions.com
1. Input Spec. (MULTI VIDEO INTERFACE)
-. 3 x AV Input (External video source).
-. 1 x CVBS (REAR CAMERA) Input (Rear camera source)
-. 1 x Analog RGB Input (Car commander original monitor output)
-. 1 x Analog RGB Input (Navigation System output)-OPTION
2. Output Spec.
-. 2 X CVBS OUTPUT (Video Out for installing Headrest monitor)
-. 1 x Audio OUTPUT
-. 1 X LCD OUTPUT(LCD Operation)
-. 4 X Audio Select Output
3. Power Spec.
- Input Power : 8VDC ~ 24VDC
- Consumption Power : 5WATT, Max
4. Switch Input mode
- NAVI/CVBS1,2 Original MUTE Function : Possible to mute each input by operating Dip S/W
- Possible to switch Input mode with remote control or toggle switch.
- Rear View Camera mode : When to sense rear gear power, be switched to Rear view
camera mode
(Impossible to switch to rear mode with Toggle S/W or the remote control)
3
1. 3 Syst em Di agr am
www.car-solutions.com
support@car-solutions.com
Navi gat i on I nput
( Anal og RGB)
AV 1
AV 2
AV 3
CVBS
(Rear
Camer a)
CAR SCREEN I NPUT
( CAR MAI N BOARD)
Remot e Cont r ol
VI DEO
CI RCUI T
POWER
CI RCUI T
MCU
Swi t ch f or sour ce t oggl e & REAR SENSE
DI SPLAY
VI DEO MUX
CVBS OUT
AUDI O OUT
CAR
I nst al l at i on
OEM LCD
HEADREST
MONI TOR
Power I nput
( +8VDC~+24VDC)
DI P S/W
4
1.4 Components
www.car-solutions.com
support@car-solutions.com
IR cable (3P) * 1ea
(HIRCAB0001)
MODE cable * 1ea
(HARETC0001)
GROUND cable (14P) * 1ea
(HGROUN0002)
Sub-board * 1ea
(QCPASS0063)
FFC cable (30P) * 1ea
(FFCABL0003)
POWER cable (10P) * 1ea
(HPOWER0005)
RGB cable * 1ea
(HNAVIC0002)
AV cable * 1ea
(HAVCAB0002)
REMOTE CONTROL * 1ea
(REMOTE0001)
5
1.4 Exterior
www.car-solutions.com
support@car-solutions.com
LED
DIP S/W
MODE
LCD IN/OUTTEST(IR)
Dimension
Horizontal length 150mm
Vertical length 95mm
Height 21mm
Power/CAN
RGB(IN) AV (IN/OUT)
6
1.5 Wiring diagram
www.car-solutions.com
support@car-solutions.com
* Power cable
FILTER
& FUSE BOX
ACC
GND
REAR-C
SAFE-N.C
CAN(H)-N.C
CAN(L)-N.C
NAVI Sel
AV1-Sel
AV2-Sel
AV3-Sel
1m
7
2.1 DIP switch
www.car-solutions.com
support@car-solutions.com
※ ON : DOWN, OFF : UP
※DIP S/W Use Example
-. Use Input Mode : AV1, Navigation (RGB), Main
-. Rear Camera : When to be installed on CVBS 4
▷ DIP S/W : 1 OFF
▷ DIP S/W : 2 OFF
▷ DIP S/W : 3 ON
▷ DIP S/W : 4 ON
▷ DIP S/W : 5 OFF
▷ DIP S/W : 6 OFF
▷ DIP S/W : 7 ON (enable CVBS4)
▷ DIP S/W : 8 OFF
※ Please make sure to disconnect the power cable of the interface and reconnect
the power cable again to apply the dip switch setting whenever changing DIP switch.
Otherwise, DIP switch setting will not be applied.
8
2.2 Remote controller
www.car-solutions.com
support@car-solutions.com
Dimension : 85 * 40 * 8 (mm)
*FACTORY MODE (Interface setting)
: Operated with pressing ▲ -> ▼ -> ▲ ->MENU buttons of the remote in sequence.
(Example : PIP implementation)
9
2.3 OSD (On Screen Display)
www.car-solutions.com
support@car-solutions.com
Analog RGB
Video
IMAGE
-
BRIGHTNESS
-
CONTRAST
-
SATURATION
-
HUE
-
SHARPNESS
-
USER IMAGE : To choose a option
among 4 prepared color shade.
Analog RGB
Video
OSD
-
LANGUAGE : To change the language
displaying on navigation, DVD, CMMB
OSD menu (select 1 among English or
Chinese)
-
TRANS : Transparency control of the OSD
background
-
H_POSITION : Horizontal movement of
the OSD window
-
V_POSITION : Vertical movement of the
OSD window
Analog RGB
Video
UTIL
-
FACTORY RESET : To reset all the
values about navigation, DVD screen
to factory default.
(NOT available for reset of the
position value of images, only for
functions inside OSD menu)
10
2.3 OSD (On Screen Display)
www.car-solutions.com
support@car-solutions.com
· Factory Mode
- Operated with pressing ▲ -> ▼ -> ▲ ->MENU buttons of the remote in sequence.
PARK
- PARK ENABLE
- H-POSITION
- V-POSITION
UTIL
-
BUTTON : Car Model Setting for using Navi button
(Refer to the next page for details)
-
FACTORY RESET : Initializing
11
2.3 OSD (On Screen Display)
www.car-solutions.com
support@car-solutions.com
※ This setting needed with wire soldering, if want to use Navi button for switching AV
sources. (Refer to the next page for further details.)
12
2.4 Parking guide line
www.car-solutions.com
support@car-solutions.com
* Factory Default : DISPLAY - DISABLE
①
① When the car gear is in reverse, Enter to
the Factory mode by ▲ → ▼ → ▲
→MENU button of remote control.
Then, the left image will be displayed on
the screen.
②
② Set “PARK ENABLE” to “ON” on the park
mode, then the line will be displayed as
shown left.
* If you would like to remove this line, just
select “Off” on the above process.
13
2.4 Parking guide line
www.car-solutions.com
support@car-solutions.com
③
④
③ Can move the line with H-Position
on the factory mode.
④ Can move the line with V-Position
on the factory mode.
14
3.1 Cautions on installation
www.car-solutions.com
support@car-solutions.com
Ignition key should be taken off before starting installation, interface power connection must be the last step
in installation.
Power cable should be separated when connecting interface.
Should be no any electronic devices or magnetic pole around installation place.
All steps of installation should be done by well-trained specialist.
Dismantling without manufacturer’s permission can not be guaranteed, (No permission to break attached
label on the board.)
Kindly check all parts are in the box, when receiving the product, if anything missing, inform to the supplier or
manufacturer.
According to our sales policy, any problems caused by user’s mistake, careless can not be guaranteed.
It may not work on a camera with 12V
15
3.2 Installation diagram
www.car-solutions.com
support@car-solutions.com
※ Please make sure that the installation
MONITOR
Offered
FFC
should be carefully conducted to avoid
from the damage of a monitor by
ESD(Electrostatic discharge) and
misalignment while connecting the
module of a monitor with cables.
•
If want to use Navi button, Solder
gray wire of offered LCD cable to
appointed point inside Head Unit.
- Applicable models : Cayenne
05~08 year, W164US, W211, Pheaton)
Original
FFC
Control Box
AV3-SEL
AV2-SEL
AV1-SEL
NAVI SEL
CAN(L)
CAN(H)
SAFE
REAE-C
GND
ACC
LED
DIP S/W MODE LCD IN/OUT
TEST
PIP RGB Hi-End
POWER/CAN
R DATA (r ed) G DATA (gr een) B DATA (bl ue)
RGB(IN)
SYNC ( whi t e)
GND (bl ack)
A/V(IN/OUT)
N. C
N. C
R
E
A
R
C
Y
E
L
L
O
W
A
A
V
V
2
1
Y
E
R
L
E
L
O
D
W
A
A
V
V
/
3
O
U
T
AUDIO R
W
V
I
H
D
I
T
E
E
O
AUDIO L
16
3.3 Soldering Point
www.car-solutions.com
support@car-solutions.com
◎Solder the gray wire on Ground cable which is
connecting sub board with main board to the Head
Unit as shown above.
*Soldering point: 5th Pin from right
*Original button : NAVI
17
4. Troubleshooting
www.car-solutions.com
support@car-solutions.com
Q. I can not switch A/V sources.
A. Check IR or Ground cable connection. Check LED lamps in the interface, if it is not on, check power cable.
Q. All I got on the screen is black.
A. Check second LED lamp of the interface is on, if not, check A/V sources connected are working well.
(Second lamp indicates AV sources connected works well.) Check interface connection has been done well.
Q. Displayed image color is not proper. (too dim or not suitable color)
A. Try to select “INITIAL” in OSD menu, if it does not work, inform the manufacturer.)
Q. Rear camera image does NOT appear.
A. Set DIP switch #7 in “ON”
Q. Unwanted A/V mode is displayed. (A/V source switching order : OEM->RGB->AV1->AV2->AV3)
A. Check DIP Switch Setting.
Q. OEM image is not displayed.
A. Check interface’s LCD In/Out cable connection. If the status keeps on, inform the manufacturer.
Q. Screen only displays white like left picture.
A. Check LCD out cable is connected well, if this status keeps, inform the manufacturer.
18
Loading...