Car Show CS-MUST10 Ford Mustang Installation Manual
Installation Guide
NOTICE OF INTENDED INSTALLATION AND USE
THE AUXILIARY VIDEO DISPLAY IS DISABLED WHEN THE VEHICLE’S PARKING BRAKE IS NOT
ENGAGED
THE INSTALLER OF THIS PRODUCT MUST INSURE THE VIDEO DISABLE CONNECTION IS
WORKING PROPERLY PRIOR TO DELIVERY OF THE VEHICLE.
IMPROPER INSTALLATION COULD DISTRACT THE DRIVER OR INTERFERE WITH SAFE OPERATION
OF THE VEHICLE, WHICH COULD RESULT IN SERIOUS INJURY OR DEATH, AND COULD ALSO
VIOLATE STATE AND/OR FEDERAL LAW.
CARSHOW ELECTRONICS DISCLAIMS ANY LIABILITY FOR ANY BODILY INJURY OR PROPERTY
DAMAGE THAT MAY RESULT FROM ANY IMPROPER OR UNINTENDED INSTALLATION AND/OR USE.
STOP
Damage to the vehicle may occur
Do not proceed until process has been completed
CAUTION
CAUTION
Process must be carefully observed in order to
reduce the risk of damage to the accessory or
vehicle
CRITICAL
Process must be carefully observed in order to
ensure a quality installation
TOOLS and EQUIPMENT
Specific tools and equipment recommended for this
process
SAFETY RISK
Observe safe practices, this process can be
dangerous and there is a risk of personal injury
TESTING and TROUBLESHOOTING
Content specific testing and troubleshooting points
CS-MUST10 Ford Mustang
NOTE: CarShow System is only compatible with vehicles equipped with Single-Disc SYNC systems
CarShow Copyright 2013 All Rights Reserved
Multi-Media Navigation System Installation Guide Rev A
CarShow Installation Guide - Ford Mustang
PREPARING FOR THE INSTALLATION
Before you start, please read these critical steps below
STEP
1
BEFORE YOU START THE
INSTALLATION,
READ THIS GUIDE!
CHECK THE BATTERY
Test the battery voltage to make sure it’s fully charged to
a minimum of 12.8 VDC
This only takes seconds and can save hours of
troubleshooting later.
TURN THE VEHICLE
OFF
Keep the Vehicle Off during the installation to avoid
setting various Vehicle Fault sensors
Keep the Vehicle OFF during the
installation
Failure to follow this may cause the AIRBAG FAULT
SENSOR to become enabled. Dealer Service
Departments charge a significant fee to reset the Fault
Sensor.
Disconnect Negative Battery Terminal Before
Starting!!
Tools Required For Installation:
Panel pry/removal tool
Various size Phillips screw drivers
7mm Socket
T10 Torx
CarShow Copyright 2013 All Rights Reserved
Installation Guide CS-MUST-IG Rev A
Page 2
CarShow Installation Guide - Ford Mustang
REMOVE CENTER CONSOLE COMPONENTS
STEP
2
Remove Shifter Trim Bezel
Carefully remove shift knob trim with panel pry tool
CAUTION
Remove Center Console
Carefully remove back of center console with panel pry
tool and pull straight up as shown at right.
Be sure to disconnect all harnesses.
CAUTION
REMOVE THE FACTORY RADIO/SYNC DISPLAY
You will need to remove multiple interior trim components prior to removing the factory radio.
The following steps will help guide you through this process.
STEP
3
OEM Radio
OEM radio shown at right
CarShow Copyright 2013 All Rights Reserved
Installation Guide CS-MUST-IG Rev A
Page 3
CarShow Installation Guide - Ford Mustang
Remove Radio Mounting Bolts
Remove 7mm bolt on beneath climate controls on right
hand side
Remove Radio Mounting Bolts
Remove 7mm bolt on beneath climate controls on left
hand side
Remove Radio Panel
Use your panel pry-tool to carefully remove radio dash
panel starting with top.
Use extreme caution to not break plastic.
Remove Radio Panel
Then, carefully remove right hand side portion of radio
panel.
Use extreme caution to not break plastic.
Unplug harness
Carefully unplug data harness from back of radio panel
CAUTION
CAUTION
CAUTION
CarShow Copyright 2013 All Rights Reserved
Installation Guide CS-MUST-IG Rev A
Page 4
CarShow Installation Guide - Ford Mustang
Remove OEM Sync Display
Remove 4 x 7mm bolts to remove Sync display
Remove SYNC Display
Carefully remove/unplug OEM SYNC display
**NOTE: Harness is extremely short so use
caution!!**
Unplug harness
Carefully unplug data harness from back of Sync
display.
Remove Right SYNC Display Bracket
Carefully remove 2 x phillips screws from right hand
side mounting bracket
Remove Left SYNC Display Bracket
Carefully remove 2 x phillips screws from left hand side
mounting bracket.
Set SYNC display aside as it will be re-installed later.
CAUTION
CAUTION
CarShow Copyright 2013 All Rights Reserved
Installation Guide CS-MUST-IG Rev A
Page 5
Loading...