Carrom 425.00, 435.00, 425.01, 435.01 Owner's Manual

SIGNATURE STICK HOCKEY

For leg assy only

For ped assy only

ITEM

DESCRIPTION

QUANTITY

3 BOLT ⅜-16 X 1 ½ ” LG HEX HEAD (#09.744.24)

16 4 WASHER 3/8 USS BLACK (#09.755.41)

16 5 LEG (#01.744.50)

4 6 LEG LEVELER (#10.755.15)

4 7 PUCK (#744.60.30) – PKG OF 2

2 8 DOME (#05.744.54)

1

10

CABLE CLAMP (#05.744.10)

3

11

SCORER BOX (#425.00.80)

1

12

BLACK FLAT WASHER - #10 (#09.770.28)

1

13

ACORN NUT (#09.744.15)

1

14

PEDESTAL BASE (#05.744.85)

1

15

BOLT – ¼ -20 X 1-1/2” HEX HEAD (#09.770.31)

4

16

FENDER WASHER – ¼ (#09.744.41)

4

17

CORNER COVER (#05.425.55)

4

18

DRINK HOLDER (#05.425.56)

4

19

DOUBLE HEADED SCREW (#09.325.09)

8

20

LEG LEVELER INSERT

(#425.00.65/set of 4) (05.325.01/for 1)

4
21

CHROME TUBE (#10.425.20)

2

22

MOUNTING FLANGE (#05.325.02)

4

23

SCREW - #8 X ½ PAN HEAD BLACK (#09.744.11)

8

For leg assy only

P.O. BOX 649 • Ludington, MI 49431 • 231-845-1263 • www.carrom.com

Congratulations on the purchase of your SIGNATURE GAME. Game set up should be near to where you will play the game. Select a clear, level floor.

TOOLS REQUIRED: Adjustable Wrench, Phillips Screwdriver

NOTE: Game requires (4) “AA” batteries (not

included) for electronic scorer to work properly.
Weak batteries may cause erratic scoring.
Game can be played with or without electronic
scorer.

FIGURE A For PEDESTAL assembly,
place the PEDESTAL where you would
like the game to be. Two people should
lift and set the Game Assembly on top of
the PEDESTAL BASE (item #14).
Position to line up with (4) threaded
inserts in bottom of Game Assembly.
Install (4) ¼ -20 x 1½ LG HEX HEAD

BOLTS (item #15) and (4) ¼” FENDER

WASHERS (item #16). (SKIP TO ELECTRONIC SCORE BOX ASSY)

FIGURE B For LEG assembly set dome aside and using two people, flip game

on its’ side. Using a rubber mallet or hammer, tap leg leveler inserts (item #20)
evenly to distribute the
pressure onto bottom of
legs. Attach the four
LEGS (item #5) to the
cabinet finger tight, one
side at a time, turning
game as needed, using
(16) ⅜”-16 x 1 ½ ” HEX
HEAD MACHINE BOLTS
(item #3) & (16)
WASHERS (item #4).
Screw the (4) LEG
LEVELERS (item #6) into
the insert in the bottom of
the legs. Make certain
they are fully screwed in prior to turning the game upright. After turning the game
upright tighten all leg bolts. Using a Phillips screwdriver, screw in the (8)
DOUBLE HEADED SCREWS (item #19) into the holes indicated in Figure B.
Install the CHROME TUBE (item #21) with the MOUNTING FLANGES (item #22)
and (2) #8 SCREWS (item #23). First mark the location for the screws 9” up on
the inside of the legs. Place the MOUNTING FLANGES on the ends of the
CHROME TUBES then align the flange screw holes with your marks. Using a
Phillips screwdriver, screw in the screws. Repeat this for both ends.

ELECTRONIC SCORE BOX ASSY: Attach SCORER BOX (item #11) to DOME
(item #8) after removing dome’s protective film. Slip SCREW projecting from top
of SCORER BOX through the hole on top of the DOME and secure with ACORN
NUT (item #13) and WASHER (item #12). Attach (3) CABLE CLAMPS (item #10)
with adhesive pads to the DOME opposite the large hole in the DOME and
secure the UPPER CABLE (part of score box item #11) to the CLAMPS. Connect
the UPPER and LOWER CABLES. Whenever dome removal is necessary,
always disconnect the (2) cables first to prevent damaging the DOME or
SCORER. CAUTION: The DOME scratches easily. Clean using glass cleaner
and a soft cloth only!

FIGURE C Attach (4) CORNER
COVERS (item #17) to each corner of
cabinet by sliding down over top edge
of cabinet first. Then attach the
CORNER COVER to the cabinet by
carefully engaging the (2) DOUBLE
HEADED SCREWS (item #19) on the
corners of the cabinet with the slots on
the inside of the corners. The (4)
DRINK HOLDERS (item #18) attach to
the CORNER COVERS by holding
them at the top of the CORNER
COVER and sliding them downward
until snug. DO NOT PUSH ON OVERLY TIGHT!

GAME FEATURES & PLAY

Game will operate with (4) “AA” batteries. Insert (4) “AA” batteries into the battery
holder. A piece of tape may be required to keep batteries from being jarred out
during heavy game play. First period will commence each time RESET BUTTON
is depressed. Game play consists of (3) two-minute periods and (1) one minute
overtime period in the event of a tie. Game play will end in overtime with a player
scoring. The period lights will flash at the END OF THE PERIOD and at the END
OF THE GAME. FINAL SCORE will flash the game winner. Electronic scoring will
turn off automatically after end of third period. Face-off with PUCK (item #7) and
HAVE FUN PLAYING!

TROUBLE SHOOTING & REPAIR

Puck will not fall through PUCK TROUGH:

1. Check Puck Trough channel for dirt and/or blockages.

2. Inspect for any binding of the switch wire within the slot. Wire should move freely within
the slot. If any binding occurs bend wire slightly to adjust.

GEAR MECHANISM hard to turn:

1. Stripping of gear teeth can cause binding. Although the game is equipped with a slip
clutch, gear tooth damage may occur after numerous game plays. Remove the gear
mechanism and inspect teeth for damage. If gear or clutch are worn, replace mechanism.

2. A worn gear housing will cause binding or sloppy action. If this occurs, replace
mechanism.

3. If gears are not turning freely, unplug the score unit, remove the dome, remove the
player(s) that are not turning freely, protect the playfield with a cloth & spray some dry
silicone lubricant spray into gearbox that player(s) were plugged into. Lastly, rotate rod(s) a
few times.

PLAYER Travel:

1. Player rubs on edge of slot. Check alignment of guide strip. Adjust if necessary by
repositioning.

2. Check for wear of guide strip or gear mechanism. If so, replace.

3. Check for debris or blockage in guide strip.

ELECTRONIC SCORING:

1. If goal is scored and not registered, check the switch wire actuator. When puck passes
the wire a score should occur. If not, bend wire to adjust.

2. If unit does not power up or score properly, check batteries.

3. Check connections. In-line cable connector, score switch terminals, and connector inside
score housing. Although the unit was inspected in assembly, loosening of connections may
occur during shipping..

SHOULD PLAYER GEAR REPLACEMENT EVER BE NECESSARY – PLEASE
FOLLOW THE PROCEDURE LISTED BELOW!

• Remove the DOME and carefully place it next to the game being careful not to
scratch it.

• Remove all players from the game by firmly pulling straight up on the player

• Carefully lift the play surface from the game

• Remove the gear from the rod by unscrewing the gear halves, which connect

the gear to the rod.
ASSEMBLY IS THE REVERSE OF THE ABOVE.

Visit www.carrom.com to register your product(s) to receive the latest updates, special offers and other product related information.

CAUTION – This is not a toy and is intended for use by or under the supervision of ADULTS!

PRODUCT REGISTRATION

07.425.20 | 8/15