CARRIN ELECTRONICS 91527 User Manual

Applicant: Carrin Electronics Co., Ltd.

FCC ID: Q9E-91527

91186 WWVB (CAR021 +CAR014)

Features:

l Weather Forecast with Sunny, Slightly Cloudy, Cloudy, Rainy and Cloud Burst.

l Radio controlled time with manual setting option

l 433MHz RF receiving frequency.

l Maximum three selectable RF channels with wireless Thermo Sensor.

(One Wireless Thermo Sensor Included)

l Transmission range: 100 ft. ( open area ).

l Measuring range:

Indoor temperature : 32°F ~ 122°F (0°C ~ 50°C)

Outdoor temperature : -58°F ~ 158°F (-50°C ~ +70°C)

Indoor Humidity : 20% ~ 90%

l With 10 feet Corded Outdoor Temperature Probe.

l Outdoor Temperature Alert function.

l Max/Min Memory for Outdoor Temperature.

l Low-battery indicator for Outdoor Remote Sensor.

l Perpetual Calendar Up to Year 2069.

l 12/24Hour time display selectable.

l Wall mount or Table Stand Selectable.

l Battery:

Main Unit : DC 1.5 V AA size x 2 pcs

Thermo & Hygro Sensor Unit : DC 1.5 V AAA size x 2 pcs

l Size:

Main Unit : 166 x 95 x 25 mm

Thermo & Hygro Sensor Unit : 98 x 77 x 20 mmMain Unit Appearance

Caution: Changes or modifications to this unit not expressly approved by the party responsible

for compliance could void the user authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause

undesired operation.

The users manual or instruction manual for an unintentional or unintentional radiator
shall caution the user that changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.

Part A- LCD

A1: Weather Forecast A2: Barometric Pressure Trend

A3:. Outdoor Temperature A4: Outdoor Humidity

A5: Outdoor Temperature Trend A6: Indoor Humidity

A7: Indoor Temperature A8: Moon Phase Display

A9: Calendar A10: Radio Controlled Time

Part B- Buttons

B1: “SNOOZE/LIGHT” button B2: “MAX/MIN” button.

B3: ” ALARM ON/OFF” button B4: “MODE” button
B5: “WEATHER” button B6: “ IN °C/°F “ button

B7: “ALERT” button B8: “+ 12/24” button
B9: “- OUT °C/°F ” button B10: “CHANNEL” button

B11: “RESET” button

Part C- Structure

C1: Wall Mount Hole C2: Battery Compartment

C3:. Stand

Thermo & Hygro Sensor Unit Appearance.

D1: Outdoor Temperature D2: Outdoor Humidity

D3: Transmission Indication LED D4: Temperature Probe & Plug
D5: “°C/°F” button D6: Channel Selecting Switch

D7: “TX” button D8: Battery Compartment.

D9: Wall Mount Hole

Set Up:

Ÿ Insert batteries.

Ÿ Use a pin to press the RESET (B11) button

Radio Controlled Clock:

l The clock automatically starts scanning the RF 433MHz signal to register new

Thermo Sensor Unit after new batteries inserted. After registered new channels or

press “CHANNEL” button (B10) to stop scanning, the clock will then scan the

WWVB time signal ( “ ” flashes on the LCD ). Buttons will not function while

scanning for WWVB time signal or Thermo sensor’s signal unless they are well

received or stopped manually.

l The clock automatically scans the time signal at 2.00 a.m. everyday to maintain

accurate timing. For failed reception, scanning stops ( “ ” on the LCD

disappear ) and repeats again at 3.00 a.m. 4.00a.m. and 5.00a.m.

l The clock manually scans the time signal by holding “ - ” button (B9) for 3

seconds. For failed reception, scanning stops. ( “ ” on the LCD disappear ).

l Hold “-” button (B9) for 3 seconds to stop scanning when receiving WWVB time

signal.