Carrier Access Adit 3200 User Manual

Adit 3200

QUICK START GUIDE

Part Number: 002-0246-0010
Product Release: 1.6
September 2007

Copyright 2007 Carrier Access Corporation. All rights reserved.
The information presented in this manual is subject to change without notice and does not represent a commitment on the

part of Carrier Access Corporation. The hardware and software described herein are furnished under a license or non­disclosure agreement. The hardware, software, and manual may be used or copied only in accordance with the terms of this
agreement. It is against the law to reproduce, transmit, transcribe, store in a retrieval system, or translate into any medium

- electronic, mechanical, magnetic, optical, chemical, manual, or otherwise - any part of this manual or software supplied
with the Adit 3200 for any purpose other than the purchaser’s personal use without the express written permission of
Carrier Access Corporation.

The Carrier Access Logo and Adit are registered trademarks of Carrier Access Corporation. All other brand or product
names are trademarks or registration trademarks of their respective companies or organizations.

Contact Information:
Carrier Access Corporation

5395 Pearl Parkway
Boulder, CO 80301-2490
Corporate Phone: [phone]
Fax: [phone]
www.carrieraccess.com

Customer Support Direct: [phone]
E-mail: [e-mail]

QUICK START GUIDE

Quick Start

In this Guide

 Unpacking and Inspection
 Installation Environment
 User Safety
 Installation

- Compliant Installation

- Wall Mounting

- Rack Mounting (Optional Feature)

- Adit 3104, 3200, 3300 and 3400 Battery Backup

 Chassis Overview
 Interface Connectors
 Reset Button
 Alarm/Status LEDs
 Web-Based Management
 Setting up a CLI Connection
 Log in
 Key Enabled Software Features
 Basic Configuration

- Setup Adit 3200 for access via Web-Browser

- Restore Factory Defaults

- Modify Default Admin User

- Configure Ethernet WAN Interface

- Configure Serial 1 as WAN

Quick Start

Unpacking and Inspection

Unpacking and Inspection

WARNING! OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES.

1. Inspect containers for damage during shipment. Report any damage to the freight carrier for
possible insurance claims.

2. Compare packing list with office records. Report any discrepancies to the office.

3. Open shipping containers, be careful not to damage contents.

4. Inspect contents and report any damage.

5. If equipment must be returned for any reason, carefully repack equipment in the original
shipping container with original packing materials if possible.

6. If equipment is to be installed later, replace equipment in original shipping container and store
in a safe place until ready to install.

Electrostatic Discharge (ESD) Precautions

ESD can damage processors, circuit cards, and other electronic components. Always
observe the following precautions before installing a system component.

1. Do not remove a component from its protective packaging until ready to
install it.

2. Wear a wrist grounding strap and attach it to a metal part of the system unit
before handling components. If a wrist strap is not available, maintain contact with the system
unit throughout any procedure requiring ESD protection.

WARNING! INTEGRATED CIRCUITS (ICS) ARE EXTREMELY SUSCEPTIBLE TO ELECTROSTATIC

DISCHARGE. UNLESS YOU ARE A QUALIFIED SERVICE TECHNICIAN WHO USES TOOLS AND
TECHNIQUES THAT CONFORM TO ACCEPTED INDUSTRY PRACTICES, DO NOT HANDLE ICS.

The ESD warning label appears on packages and storage bags that contain static-sensitive products and
components.

Installation Environment

The environment in which you are installing the Adit 3000 must meet the following conditions:

z Operating temperature range: 32° to 104° F (0° to 40° C)
z Storage temperature range: -40° to 158° F (-40° to 70° C)
z Maximum operating altitude: 10,000 ft. (3,048 m)
z Maximum non-operating altitude: 40,000 ft. (12,192 m)
z Relative humidity (non-condensing) range: 0 to 95%

WARNING! THE ADIT 3000 IS DESIGNED FOR WALL AND RACK MOUNTING ONLY. IT IS NOT

DESIGNED FOR DESKTOP USE.

4 Adit 3200 - Release 1.6

Quick Start

User Safety

User Safety

CAUTION! WHEN USING YOUR TELEPHONE EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD

ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE
INCLUDING THE FOLLOWING:

z Do not use this product near water for example, near a bathtub, washbowl, kitchen sink or

laundry tub, in a wet basement or near a swimming pool.

z Avoid using a telephone (other than a cordless type) during an electrical storm. There may be

a remote risk of electric shock from lightning.

z Do not use the telephone to report a gas leak in the vicinity of the leak.
z Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a

fire. They may explode. Check with local codes for possible special disposal instructions.

z Refer to the installation section of this manual for a safe and proper installation procedure. All

wiring external to this equipment should follow the current provision of the National Electrical
Code.

, ELECTRIC SHOCK AND INJURY TO PERSONS,

Installation

The following are instructions for a compliant installation of the Adit 3200. Please note the following
warnings, before installing the unit.

For wall and rack mount instructions, use the links listed below to the appropriate section:

z Wall Mounting
z Rack Mounting (Optional Feature)

WARNING! OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES. SEE

Electrostatic Discharge (ESD) Precautions ON PAGE 4 FOR DETAILED INFORMATION.

WARNING! THE T1 NETWORK INTERFACES ARE CERTIFIED WITH THE FCC AND INDUSTRY

ANADA FOR DIRECT CONNECTION TO PUBLIC COMMUNICATION NETWORKS. SECONDARY

C

LIGHTNING SURGE AND AC POWER CROSS PROTECTION IS PROVIDED. UTILIZE LISTED PRIMARY
PROTECTORS WITH A NOMINAL 230V BREAKDOWN RATING TO ENSURE VOLTAGE COORDINATION
WITH SECONDARY PROTECTION. THE INSTALLER IS REQUIRED TO FOLLOW LOCAL OR NATIONAL

ELECTRIC CODES FOR COMMUNICATION CIRCUITS.

Adit 3200 - Release 1.6 5

Quick Start

Installation

Compliant Installation

NOTE: It is important the DS1/E1 Network Interface Cables are secured separately from the

power and Signal Cables.

1. Inspect the unit.

2. Mount the unit, see Wall Mounting on page 7, or Rack Mounting (Optional Feature) on page 8
for detailed instructions.

3. Ground the unit. See Grounding the Unit on page 12.

WARNING! THE SEPARATE PROTECTIVE EARTHING TERMINAL PROVIDED ON THIS PRODUCT

SHALL BE PERMANENTLY CONNECTED TO EARTH. SEE Grounding the Unit ON PAGE 12.

4. Connect DS1 (T1) and Ethernet connectors as needed.

5. Connect RS-232 connector and open Terminal Emulator software on your PC. Note: With this
connected first, the boot process can be monitored.

6. Connect Power to the unit.

7. Monitor the boot process on your PC, when complete the status light should be green.

8. For any software enabled features, enter the key command. See the key command in the Adit
3000 CLI Reference Manual, for detailed information.

9. To verify use the show version command.

10. Now you can proceed to provisioning the unit. See Basic Configuration on page 22 for
information.

6 Adit 3200 - Release 1.6

Quick Start

Mounting Bracket

Leave adequate space
at the front/back for
access to connectors

Back of unit

Front of unit

Installation

Wall Mounting

Before beginning the mounting process, verify that the installation area is a stable environment, clean
and free from extremes of temperature, shock, vibration and EMI. See Installation Environment on
page 4.

The Adit 3000 is delivered with mounting brackets that can easily be attached for quick and easy wall
mounting, as shown in the illustration above.

To install the unit to the wall:

1. Attach the wall mount brackets to the Adit 3000, with wall attachment flange pointing away

from the unit, as shown above. Attach with 4 screws provided (2 for each bracket).

2. Mount the unit to the wall using appropriate mounting screws (not included). Note: it is

acceptable to mount on drywall with suitable anchor-type mounting screws.

NOTE: The Adit 3000 must be mounted with the brackets on the top and bottom, as shown

above.

Adit 3200 - Release 1.6 7

Quick Start

23 in rack

19 in rack

Front

Front

screws

screws

screws

screws

Rack Mount Tray

Rack Mount Tray

Mounting Ear

Mounting EarMounting Ear

Mounting Ear

Mounting Ear

Rack Mounting Tray

Installation

Rack Mounting (Optional Feature)

NOTE: Rack mounting kits are available for both 19 and 23 inch racks. 1 Rack Unit (RU) of

spacing is required above the Adit 3000 in the Rack Mount Unit.

To rack mount the Adit 3000, follow the instructions below:

1. Attach bracket ears to Rack Mounting Tray using four #10-32 x 1/4” screws on each side. The
Mounting Ears can be used for both a 19 or 23 inch rack. The drawing below shows a top view
of the 2 versions.

8 Adit 3200 - Release 1.6

2. Attach the Rack Mounting Tray assembly (with mounting ears attached) to rack, using four
#10-32 x 1/4” screws (two on each mounting ear).

3. Remove wall mount and screws, if attached, from Adit 3000 unit.
Note: Adit 3000 and wall mounting bracket are not assembled from the factory.

Quick Start

Tray Slide

screws

screws

Installation

4. Place the Adit on the Tray Slide and attach with 4 screws removed in step 2.

5. Slide the assembled piece (Adit 3000 and Tray Slide) onto the installed Rack Mounting Tray.

6. Secure the Tray Slide to the Rack Mounting Tray with the attached screws on the Tray Slide.

Adit 3200 - Release 1.6 9

Quick Start

Installation

Adit 3104, 3200, 3300 and 3400 Battery Backup

The Adit 3104, 3200, 3300 and 3400 Battery Backup (P/N 730-0132), is a wall-mount battery backup
unit to provide up to 8 hours battery backup.

Please see the Battery Backup User Manual for product information and installation instructions, which
is provided with unit.

Note: This is an optional feature.

10 Adit 3200 - Release 1.6

Quick Start

(1) 10/100Base-T
Ethernet (WAN)

(4) 10/100Base-T
Ethernet (LAN)

Alarm
Status

Reset

RS-232
Management
Port

Power/Battery/Status

Ground

Back

Front

(1) DS1/E1 (WAN)
(E1-future)

Chassis Overview

Chassis Overview

Adit 3200 - Release 1.6 11

Quick Start

Chassis
Ground

Interface Connectors

Interface Connectors

The following are the Adit 3200 interface connectors:

Front of Adit

z (1) DS1 WAN port (RJ-48C). Note: E1 will be in a future release.
z (1) 10/100Base-T WAN port (RJ-45)
z (4) 10/100Base-T switched LAN ports (RJ-45)

Back of Adit

z RS-232 craft port connector for local management
z Power input connector
z Ground connector

Grounding the Unit

WARNING! THE ADIT 3200 IS REQUIRED TO BE PERMANENTLY GROUNDED FOR THE

PROTECTION OF USERS AND SERVICE PERSONNEL.

Chassis ground is located on the back of the unit.
To ground the unit:

1. Connect a minimum 14 AWG ground
wire with a #8 ring tongue terminal (not
included) to the chassis ground on the
back of the unit. Secure with the 8-32
screw and lock washer provided.

2. Connect the opposite end of the ground
wire to a suitable earth grounding point
such as a building grounding electrode,
metal water pipe, or metal building
structure that is in compliance with article 250 of NEC.

12 Adit 3200 - Release 1.6

Quick Start

PIN 10 , ORANGE
PIN 5, BLACK

Interface Connectors

Power

The Adit 3000 is powered by a limited -48 VDC Power source. The
following options are available:

z AC/DC Converter
z Battery Backup module

AC/DC Converter

An AC/DC Converter generates 48VDC from any worldwide AC power source.

To connect AC power:

1. Plug power connector from AC/DC converter into rear of Adit 3000.

2. Connect AC/DC converter to wall outlet.

3. A green light should appear on the Status LED on the front of the unit.

CAUTION! INCORRECT WIRING OF CORD MAY CAUSE EXTERNAL FUSE FAILURE.

WARNING! POSSIBLE SHOCK HAZARD EXISTS, PLEASE FOLLOW INSTRUCTIONS CAREFULLY.

To connect -48 VDC power:

1. Wire appropriate connector to open end of the DC Power cable.

Orange = -48 Black = Ground (+)

2. Plug the DC power connector in the -48 VDC input power connector.

3. Apply power to connector from -48 VDC power source.

4. A green light should appear on the Status LED on the front of the unit.

WARNING! EXTERNAL FUSE PROTECTION IS REQUIRED ON THE 48VDC INPUT WHEN

CONNECTED TO A DC POWER SOURCE NOT SUPPLIED BY CARRIER ACCESS.

Fuse Recommendations, or equivalent:

Recommended Fuse AMP Rating
Littelfuse 48101.5 1.5 Amp
Bussman GMC-1.5A 1.5 Amp

Battery Connection

The Adit 3000 Battery connection is provided for Battery Backup. See Adit 3104, 3200, 3300 and 3400
Battery Backup on page 8 for additional information.

Adit 3200 - Release 1.6 13

Quick Start

15

69

Interface Connectors

RS-232 Craft Port (Female DB-9)

The RS-232 craft port connector (female) is for connection to an external PC or Hayes-compatible
modem for local or remote configuration, management, and performance monitoring using the Adit
3000 Command Line Interface (CLI).

The RS-232 craft port connects via a female DB-9 connector on the Adit

3000.

The pinouts are as follows:

Pin Number Direction Description

1 Outbound Carrier Detect

2 Outbound Receive Data

3 Inbound Transmit Data

4 Inbound Data Terminal Ready

5 N/A Signal Ground

6 Outbound Data Set Ready

7 Inbound Request to Send

8 Outbound Clear to Send

9 N/C Not connected

14 Adit 3200 - Release 1.6

Quick Start

18

Interface Connectors

DS1/E1 Connection Ports

Each DS1/E1 connection port is equipped with a standard RJ-48C (female) on the
Adit 3000 unit. Note: E1 will be available in a future release.

The pinouts are as follows:

DS1/E1 RJ-48C

The pinouts are as follows:
Note: This is a hub pinout, you will need a straight cable to connect to a PC.

Pin Name Description

1 Receive Ring Receive from DS1 network
2 Receive Tip Receive from DS1 network
3 N/C Not connected
4 Transmit Ring To DS1 network
5 Transmit Tip To DS1 network
6-8 N/C Not connected

The LEDs are as follows (left LED only):

State Description

Off Off line
Green Normal
Red Loss of Signal (LOS)
Yellow Bipolar Violation (BPV)
Flashing Green Loopback active
Flashing Yellow Yellow Alarm (Remote Alarm Indication)
Flashing Red (Slow) Loss of Frame (LOF) or Alarm Indication Signal (AIS)
Flashing Red (Fast) Self-test Failure

Adit 3200 - Release 1.6 15

Quick Start

18

8 1

Reset Button

10/100Base-TX Ethernet

The 10/100Base-TX Ethernet (female) ports provide connectivity for Router
WAN and/or LAN ports and for management connection via Telnet and/or
SNMP to a Network Management System.

Ethernet (RJ-45)

The pinouts are as follows:

Pin Name Description

1 Receive + Receive from network
2 Receive - Receive from network
3 Transmit + Transmit to network
4-5 N/C Not connected
6 Transmit - Transmit to network
7-8 N/C Not connected

The LEDs are as follows:

LED State Description

Left LED The left LED shall show Link Status.

Right LED The right LED shall indicate Link Speed.

Reset Button

The system can be reset by pressing the reset button located on the front panel.

Off Link Down
Green Link Up

Flashing Green Traffic on Link
Yellow Collision status

Off 10 Mbit/sec, down or not connected
Green 100 Mbit/sec

16 Adit 3200 - Release 1.6

Quick Start

Alarm/Status LEDs

Alarm/Status LEDs

LED State Description

Critical Off No critical alarms present

Red Critical alarms present. Critical alarms include:

user-configured manor environmental inputs.

Major Off No major alarms present

Red Major alarm present. Major alarms include:

user-configured manor environmental inputs, DS1 short, DS1 open, DS1
facility alarm, DS1 RAI, DS1 AIS, DS1 LOF, DS1 LOS, WAN fault,
Ethernet fault and dead card alarms.

Minor Off No minor alarms present

Red Minor alarms present. Minor alarms include:

user-configured minor environmental inputs, DS1 excessive line code
violations.

Status Off No power to system

Green Application running, no detected system problems.

Green Flashing Power-On Self Test (POST) successful. System booted. Loading

Application.

Green/Yellow Flashing alternate colors. Application Self Test in Process.

Yellow Yellow while booting. If this stays a steady yellow the Power-On Self Test

(POST) failed.

Yellow Flashing Power-On Self Test (POST) In Process.

Red System Failure

Adit 3200 - Release 1.6 17

Quick Start

Web-Based Management

Web-Based Management

The web-based management interface allows you to control various system parameters. The interface
is accessed through a web browser.

To access the management console:

NOTE: The following assumes that you have connected the PC to the LAN port of the Adit

3200.

1. Launch a web browser on your PC in the LAN to which the Adit 3000’s LAN port is connected.
Note: If connection to the 3000 is to be through an Ethernet or T1 WAN, the remote admin
WAN access must be enabled with the following command sequence:

Command Description

Username: admin
Password: ********

Adit 3200> enable Enter the Privileged mode.

Password: ******** Enter password for the Privileged mode.

#configure terminal Enter the Configuration mode.

(config)# remote-admin web

primary-port enable

Log into the system (username and password).

Enable remote web admin.

2. Type the Adit 3000’s IP address or name in the address bar.
Example: http://192.168.1.1.

z Default IP address is http://192.168.1.1

Note: to display the current IP address of the systems, use the following CLI command:

#show interface ethernet 1 (LAN)
#show interface ethernet 2 (Eth WAN)

3. Login to the unit.
Enter User Name and Password. Note: these setting should be changed from the default settings
after the initial login.

z Default user name is admin
z Default password is admin 123

NOTE: After a few minutes of inactivity, the session will automatically timeout and the

operator will be required to log in to continue the session.

WARNING! IF YOUR USER NAME AND PASSWORD ARE SET TO THE DEFAULT SETTING, IT IS

RECOMMENDED THAT YOU MODIFY THEM FOR SECURITY PURPOSES.

18 Adit 3200 - Release 1.6

Quick Start

Setting up a CLI Connection

Setting up a CLI Connection

A CLI connection will require the LAN or WAN IP address of the unit. Note: If the WAN IP address
is used, the remote admin WAN access must be enabled with the following command sequence:

Command Description

Username: admin
Password: ********

Adit 3200> enable Enter the Privileged mode.

Password: ******** Enter password for the Privileged mode.

#configure terminal Enter the Configuration mode.

(config)# remote-admin web

primary-port enable

Log into the system (username and password).

Enable remote web admin.

NOTE: For Adit 3200 CLI commands see the Adit 3000 CLI Reference Manual. This is a

separate document and can be found on the CD that is provided with the product, or on the
Carrier Access customer website.

To connect with CLI, set up the connection:

z If connecting via the Ethernet 100Base-TX connection, use a Telnet TCP/IP program to access

the CLI. This requires an IP address of the unit.
Note: to display the current IP address of the unit, use the ifconfig command.

z If connecting via RS-232, the port settings should be set to:

Bits per second: 115200 Data bits: 8
Parity: None Stop bits: 1
Flow control: None

z Set your Terminal Emulation to: VT100

NOTE: When using Tera Term (Telnet program) TCP/IP, CLI commands will not be

recognized until the following setup is completed.

z In Tera Term go to Setup/Terminal
z Set the New-line/Transmit value CR+LF

Adit 3200 - Release 1.6 19

Quick Start

Log in

Log in

After successful connection, via telnet or HyperTerm, the user must login. Default Logins are:

After successful login the prompt will be displayed as follows:

NOTE: It is recommended that you change your password from the default.

Login: admin
Password: admin123

Adit 3200>

20 Adit 3200 - Release 1.6

Quick Start

Key Enabled Software Features

Key Enabled Software Features

The Adit 3200 has additional features that are not provided on the base system. These features can be
purchased with the product or added later as needed. These features are enabled via a Software Key
(example: G.729). The number of keyed features may expand with the development of the product,
therefore to see a list of current keyed features, or to purchase a key, contact Carrier Access Customer
Service or Sales.

To enter a software key, use the following CLI command:

Syntax:

Example: (config)# key cxusdfutkj3diosn412C

NOTE: Keys may only be entered through the CLI (not through the GUI).

The Key Enabled Software Features are displayed on the Advanced/Technical Information window.

(config)# key {key-code}

This information is also displayed with the following CLI command:

Adit 3200> show version

Application Version: 1.5.1
Compilation Time: Thu Jun 14 2007 18:43:10
FPGA Version: 2.00
Board Version: 0 003-1129-0020
IXP400 Software Release: 1_4 SQA4_1
Voice Slot 1 : FXS Card Present: Rev 1.00 CLEI Code:IPU3AARBAA
Voice Slot 2 : -- EMPTY -­Voice Slot 3 : -- EMPTY -­Vendor: Carrier Access
CLEI Code: IPMP200JRA

Product Features:
VPN enabled.
MGCP enabled.
SIP enabled.

Adit 3200 - Release 1.6 21

Quick Start

Basic Configuration

Basic Configuration

The following configuration is divided into logical sections, where each section configures an additional
function. The first must be configured before the second and so forth, however, you may stop at any
section and not add the following feature.

NOTE: The order in which commands are entered can affect the successful provisioning of

the Adit 3200.

z Setup Adit 3200 for access via Web-Browser
z Restore Factory Defaults
z Modify Default Admin User
z Configure Ethernet WAN Interface
z Configure Serial 1 as WAN

Setup Adit 3200 for access via Web-Browser

The following steps will configure the Adit 3200 to allow access to the Web Browser for configuration,
through one of the 4 10/100Base-T LAN connections.

Note: for LAN access, no additional configuration is required to access the Adit using the web browser.
To configure the WAN access:

1. Connect to the CLI via the DB-9 RS-232. See Setting up a CLI Connection on page 19.

2. Enable the remote admin WAN access with the following command sequence:

Command Description

Username: admin
Password: ********

Adit 3200> enable Enter the Privileged mode.

Password: ******** Enter password for the Privileged mode.

#configure terminal Enter the Configuration mode.

(config)# remote-admin web

primary-port enable

Log into the system (username and password).

Enable remote web admin.

22 Adit 3200 - Release 1.6

Quick Start

Basic Configuration

Restore Factory Defaults

If the unit is not out-of-the-box, you may want to verify that the unit is set to defaults. Note: This will
reset the IP address back to the default setting of 192.168.1.1.

In the web-browser:

z Select Advanced from the Navigation bar
z Select Restore Defaults

z Select OK to restore defaults

Adit 3200 - Release 1.6 23

Quick Start

Basic Configuration

Modify Default Admin User

For security purposes it is recommended that the Administrator User be changed from the default
settings.

Modify the Administrator User in the web-browser:

z Select Advanced from the Navigation bar
z Select Users icon

z Select Administrator, to open the profile.

24 Adit 3200 - Release 1.6

Quick Start

Basic Configuration

z Modify the User information, and select OK to save. It is important to note that you need to

have a minimum of one user with Administrative Privileges. For users with other access
levels, add a New User.
Note: For security purposes, the password should be changed.

z You will be required to login again, if you have modified the User Profile that you are logged

in with.

Adit 3200 - Release 1.6 25

Quick Start

Basic Configuration

Configure Ethernet WAN Interface

In the web-browser:

1. Select Network Connections from the Navigation bar.

2. It is recommended that you disable/delete the Serial1 port.

3. Select (click) Ethernet 2 (WAN Ethernet) connection to configure.

4. Select the Enable button, to configure the WAN Ethernet up (or in-service).

5. Select the Settings button.

26 Adit 3200 - Release 1.6

Quick Start

Basic Configuration

6. Set Internet Protocol to Obtain an IP Address Automatically, from the pulldown menu. This

will enable the Adit 3200 as a DHCP Client. Leave the other fields to their default settings.

7. Select Apply to apply the new settings.

Adit 3200 - Release 1.6 27

Quick Start

Basic Configuration

Configure Serial 1 as WAN

In the web-browser:

1. Select Network Connections from the Navigation bar.

2. Select Serial 1.

3. Select Settings button.

4. Set Network to WAN.

5. Select Apply to apply the new settings.

28 Adit 3200 - Release 1.6