Carrier Access Adit 3000 User Manual

Adit 3000 Series and

Multi-Service Router (MSR) Card

CLI REFERENCE MANUAL

Part Number: 770-0165 BB

Product Release: Adit 3000 Series - 1.6

MSR Card - 2.0

April 2008

Copyright 2008 Turin Networks Inc. All rights reserved.

The information presented in this manual is subject to change without notice and does not represent a commitment on the
part of Turin Networks Inc. The hardware and software described herein are furnished under a license or non-disclosure
agreement. The hardware, software, and manual may be used or copied only in accordance with the terms of this agreement.
It is against the law to reproduce, transmit, transcribe, store in a retrieval system, or translate into any medium - electronic,
mechanical, magnetic, optical, chemical, manual, or otherwise - any part of this manual or software supplied with the Adit
3000 series or MSR products for any purpose other than the purchaser’s personal use without the express written
permission of Turin Networks Inc.

The Turin Networks logo and Adit are registered trademarks of Turin Networks Inc. All other brand or product names are
trademarks or registration trademarks of their respective companies or organizations.

Corporate Contact Information:

Turin Networks
1415 North McDowell Blvd.
Petaluma, CA 94954
Phone: [phone]
Fax: [phone]
www.TurinNetworks.com

Customer Support:

E-mail: [e-mail]
Phone: [phone] or 303-218-5655

Supporting Software Versions:

Adit 3104 - Release 1.6

Adit 3200 - Release 1.6

Adit 3500 - Release 1.6

Multi-Service Router (MSR) Card - Release 2.0

Safety Information

CAUTION! WHEN USING YOUR TELEPHONE EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD

ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK AND INJURY TO PERSONS,
INCLUDING THE FOLLOWING:

z Do not use this product near water for example, near a bathtub, washbowl, kitchen sink or

laundry tub, in a wet basement or near a swimming pool.

z Avoid using a telephone (other than a cordless type) during an electrical storm. There may be

a remote risk of electric shock from lightning.

PREFACE

Preface

z Do not use the telephone to report a gas leak in the vicinity of the leak.

z Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a

fire. They may explode. Check with local codes for possible special disposal instructions.

z Refer to the installation section of this manual for a safe and proper installation procedure. All

wiring external to this equipment should follow the current provision of the National Electrical
Code

NOTE: For Safety and Compliance information for the Multi-Service Router (MSR) card and

Adit 600 platform, please refer to the Adit 600 User Manual.

Preface

Notices

This manual contains important information and warnings that must be followed to ensure safe
operation of the equipment.

DANGER! A DANGER NOTICE INDICATES THE PRESENCE OF A HAZARD THAT CAN OR WILL

CAUSE DEATH OR SEVERE PERSONAL INJURY IF THE HAZARD IS NOT AVOIDED.

CAUTION! A CAUTION NOTICE INDICATES THE POSSIBILITY OF INTERRUPTING NETWORK

SERVICE IF THE HAZARD IS NOT AVOIDED.

WARNING! A WARNING NOTICE INDICATES THE POSSIBILITY OF EQUIPMENT DAMAGE IF THE

HAZARD IS NOT AVOIDED.

NOTE: A Note indicates information to help you understand how to perform a procedure or how the

system works. Notes should be read before performing the required action.

iv Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

Table of Contents

Preface

Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

1 Introduction

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Prompt Identifier. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

User Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

Privileged Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

Configuration Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

Command Syntax Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-5

Command Line Interface Help. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

Shortcuts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

2 User Mode

date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

ping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

show . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

traceroute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-33

TABLE OF CONTENTS

3 Privileged Mode

clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

configure terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

copy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

debug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12

exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12

help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13

history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14

log clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15

no debug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16

ping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17

Table of Contents

4 Global Configuration Mode

reload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18

show . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19

traceroute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-67

upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-67

Commands for Entering Configuration Submodes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

Global Configuration Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4

access-control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4

access-list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

authentication login . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6

clock source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6

controller lcc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7

controller t1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7

date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

delete local-server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10

dial-peer voice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11

dmz-host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12

do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13

dynamic-dns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14

end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16

exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16

help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-17

history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-18

host-filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19

interface ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19

interface multilink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20

interface serial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20

ipsec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-21

ip dhcp pool ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-25

ip domain-name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-25

ip host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-25

key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-26

l2tpc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-26

local-server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-27

log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-28

mail-server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-33

nat-bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-35

network-object . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-35

no commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-36

port-trigger service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-53

pptpc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-53

pptps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-53

radius-client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-54

vi Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

Table of Contents

remote-admin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-54

router ospf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-56

security-default . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-57

security-log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-58

service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-59

snmp-server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-60

static-dns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-62

time-range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-62

username . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-63

vlan (global) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-63

vlan (vlan-id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-64

voice-codec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-64

voice-port (global) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-65

voice-port fxs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-65

voice-port trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-66

voice-service sip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-66

5 Configuration - LCC Controller Mode

description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3

end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4

exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4

history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5

no command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5

shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

6 Configuration - T1 Controller Mode

description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2

do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3

ds0-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4

end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4

exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4

fdl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5

framing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5

history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6

idle-pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6

lbo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7

linecode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8

loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8

loopdetect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9

no commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9

pri-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10

shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11

tdm-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11

threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI vii

Table of Contents

7 Configuration - DHCP Pool Ethernet Mode

8 Configuration - Dial Peer FXS Mode

do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2

end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3

end-address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3

exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3

history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4

lease . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4

no commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5

option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6

relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6

start-address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7

static-lease . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7

subnet-mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8

wins server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8

block-out-caller-id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2

call-wait-caller-id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2

call-waiting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2

calling-party-disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2

codec preference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3

destination-pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3

do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4

end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5

exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5

fax-protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6

history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6

modem-protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7

no commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8

sip-authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10

9 Configuration - Dial Peer Trunk Mode

codec preference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2

destination-pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2

do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3

end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4

exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4

fax-protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4

history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-5

modem-protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-5

no commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-6

prefix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7

sip-authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7

strip-digits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-8

viii Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

Table of Contents

10 Configuration - Dial Peer VoIP Mode

destination-pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2

do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3

end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-4

exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-4

history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-4

no commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-5

prefix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-6

session-target . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-6

strip-digits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-7

user-id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-7

11 Configuration - Ethernet Interface Mode

description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-2

do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-3

end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-4

exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-4

firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-4

full-duplex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-5

half-duplex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-5

history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-6

ip address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-6

ip default-gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-7

ip default-route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-7

ip dhcp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-7

ip mtu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-8

ip ospf authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-9

ip ospf authentication-key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-10

ip ospf cost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-10

ip ospf dead-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-10

ip ospf disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-11

ip ospf hello-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-11

ip ospf message-digest-key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-11

ip ospf priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-12

ip ospf retransmit-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-12

ip ospf transmit-delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-12

ip primary-dns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-13

ip proxy-arp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-13

ip rip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-14

ip route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-15

ip route-mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-15

ip secondary-dns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-16

metric . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-16

no commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-17

release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-23

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI ix

Table of Contents

12 Configuration - Multilink Interface Mode

remote-admin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-23

renew . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-23

schedule-availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-24

shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-24

sip-alg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-24

speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-25

tos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-25

description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-2

do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-3

end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-4

exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-4

firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-4

history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-5

ip address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-5

ip default-route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-6

ip mtu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-6

ip ospf authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-7

ip ospf authentication-key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-8

ip ospf cost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-8

ip ospf dead-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-8

ip ospf disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-9

ip ospf hello-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-9

ip ospf message-digest-key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-9

ip ospf priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-10

ip ospf retransmit-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-10

ip ospf transmit-delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-10

ip primary-dns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-11

ip rip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-11

ip route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-12

ip route-mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-13

ip secondary-dns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-13

metric . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-13

no commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-14

ppp authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-21

ppp encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-21

ppp exec-timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-21

ppp link-fragmentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-22

ppp on-demand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-22

ppp password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-22

ppp qos-interleaving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-23

ppp restart-timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-23

ppp time-btwn-reconnect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-23

x Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

Table of Contents

ppp username . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-24

schedule-availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-24

shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-24

sip-alg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-25

13 Configuration - Serial Interface Mode

description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-2

do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-3

encapsulation ppp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-4

end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-4

exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-4

firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-5

history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-5

ip address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-6

ip default-route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-6

ip mtu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-6

ip ospf authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-7

ip ospf authentication-key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-8

ip ospf cost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-8

ip ospf dead-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-8

ip ospf disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-9

ip ospf hello-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-9

ip ospf message-digest-key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-9

ip ospf priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-10

ip ospf retransmit-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-10

ip ospf transmit-delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-10

ip primary-dns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-11

ip rip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-11

ip route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-12

ip route-mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-13

ip secondary-dns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-13

metric . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-13

multilink-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-14

no commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-14

ppp authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-21

ppp encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-21

ppp exec-timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-21

ppp link-fragmentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-22

ppp on-demand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-22

ppp password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-22

ppp restart-timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-23

ppp time-btwn-reconnect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-23

ppp username . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-23

schedule-availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-24

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI xi

Table of Contents

14 Configuration - IPSec Mode

shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-24

sip-alg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-24

aggressive-mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-2

authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-2

description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-2

do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-3

dpd-delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-4

dpd-enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-4

dpd-timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-4

encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-5

end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-5

exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-5

group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-6

hash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-6

history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-7

ip route metric . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-7

ipsec-conn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-8

ipsec-manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-8

key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-8

lifetime . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-9

local-subnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-9

max-retries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-10

mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-10

net-type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-11

netbios remote-brc-addr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-11

no commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-12

reconnect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-17

rekey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-17

remote-ip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-17

remote-subnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-18

schedule-availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-18

session-key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-19

set-pfs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-19

transform-set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-20

Example of IPSec Connection Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-21

xii Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

Table of Contents

15 Configuration - L2TPC Mode

do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-2

end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-3

exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-3

firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-3

history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-4

host-ip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-4

ip address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-5

ip default-route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-5

ip mtu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-5

ip ospf authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-6

ip ospf authentication-key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-7

ip ospf cost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-7

ip ospf dead-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-7

ip ospf disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-8

ip ospf hello-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-8

ip ospf message-digest-key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-8

ip ospf priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-9

ip ospf retransmit-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-9

ip ospf transmit-delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-9

ip primary-dns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-10

ip rip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-10

ip route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-11

ip route-mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-12

ip secondary-dns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-12

local-secret . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-12

metric . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-13

no commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-13

ppp authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-21

ppp encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-21

ppp exec-timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-21

ppp on-demand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-22

ppp password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-22

ppp restart-timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-22

ppp time-btwn-reconnect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-23

ppp username . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-23

schedule-availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-23

shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-24

sip-alg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-24

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI xiii

Table of Contents

16 Configuration - OSPF Mode

17 Configuration - PPTPC Mode

area commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-2

compatible rfc1583 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-3

do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-4

end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-5

exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-5

history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-5

network area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-6

no commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-7

router-id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-9

Sample Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-10

do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-2

end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-3

exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-3

firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-3

history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-4

host-ip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-4

ip address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-5

ip default-route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-5

ip mtu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-5

ip ospf authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-6

ip ospf authentication-key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-7

ip ospf cost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-7

ip ospf dead-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-7

ip ospf disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-8

ip ospf hello-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-8

ip ospf message-digest-key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-8

ip ospf priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-9

ip ospf retransmit-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-9

ip ospf transmit-delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-9

ip primary-dns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-10

ip rip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-10

ip route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-11

ip route-mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-12

ip secondary-dns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-12

metric . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-12

no commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-13

ppp authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-20

ppp encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-20

ppp exec-timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-21

ppp on-demand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-21

ppp password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-21

xiv Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

Table of Contents

ppp restart-timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-22

ppp time-btwn-reconnect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-22

ppp username . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-22

schedule-availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-23

shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-23

sip-alg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-23

18 Configuration - PPTPS Mode

do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-2

end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-3

end-address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-3

exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-3

history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-4

idle-time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-4

no commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-5

ppp authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-6

ppp encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-6

shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-7

start-address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-7

19 Configuration - RADIUS Mode

authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-2

do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-3

end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-4

exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-4

history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-4

host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-5

key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-5

20 Configuration - VLAN Mode

do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-2

end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-3

exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-3

history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-3

no commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-4

port-dot1q . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-5

port-priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-5

port-protocol-filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-6

pvid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-6

tag-all . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-7

vlan-feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-7

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI xv

Table of Contents

21 Configuration - VLAN Port Mode

22 Configuration - Voice Port Mode

do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-2

end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-3

exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-3

history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-3

no commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-4

port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-4

priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-5

voip-interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-5

digit-map (global) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-2

do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-3

end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-4

exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-4

history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-4

no digit-map (global) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-5

tos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-5

23 Configuration - Voice Port FXS Mode

comfort-noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-2

description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-2

do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-3

echo-cancel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-4

end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-4

exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-4

history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-5

input-gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-5

no commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-6

output-gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-7

per-line-logging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-7

shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-7

signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-8

24 Configuration - Voice Port Trunk Mode

comfort-noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-2

connection lcc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-2

connection t1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-2

description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-3

digit-map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-3

do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-4

echo-cancel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-5

end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-5

exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-5

xvi Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

Table of Contents

history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-6

input-gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-6

isdn switch-type (PRI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-7

no commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-8

output-gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-11

registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-12

signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-14

trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-15

25 Configuration - Voice Service SIP Mode

calling-party-disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-2

conference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-2

do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-3

dtmf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-4

early-media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-4

end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-5

exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-5

fax-protocol-t38 ecs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-6

fax-protocol-t38 redundancy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-6

fax-protocol-t38 signaling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-7

feature-mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-7

gateway-ip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-8

history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-8

no commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-9

outbound-proxy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-11

phone-number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-11

prack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-11

privacy-mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-12

proxy-server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-12

proxy-type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-13

redundancy advance-retries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-13

redundancy advance-timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-14

redundancy filter-incoming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-14

redundancy primary-address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-14

redundancy rollback-timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-15

redundancy secondary-address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-15

redundancy ttl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-16

redundancy type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-16

registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-17

rtp-base-port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-17

session-timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-18

sip-port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-19

transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-19

Index

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI xvii

Table of Contents

xviii Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

CHAPTER

1

Introduction

This Reference Manual covers the Command Line Interface (CLI) for the following products:

z Adit 3000 series (Adit 3104, Adit 3200, and Adit 3500)

z Multi-Service Router (MSR) Card (a service card for the Adit 600 platform)

The chapters are broken down into Modes and Configuration Groups. All commands that are
listed in each group are described in the chapter.

NOTE: Throughout this manual, examples primarily reflect the Adit 3000 series. Where

differences exist for the MSR card, these differences are noted.

In this Chapter

 Overview

 Command Syntax Conventions

 Command Line Interface Help

 Shortcuts

Introduction

Overview

Overview

The Adit 3000/MSR CLI has three command modes, each with access to different command sets. The
following displays the basic flow of the CLI.

1-2 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

Introduction

Overview

Prompt Identifier

When you initiate a CLI session it will open in User mode, which is indicated by the ">" prompt. At any
time you can quickly determine which mode you are in by the prompt.

Command

Access Method Prompt Displayed Exit Method

Mode

User Login adit 3104>

adit 3200>
adit 3500>
adit MSR>

Privileged From User mode, enter the

enable command

Global
Configuration

From Privileged mode, enter
the configure terminal
command.

adit 3104#
adit 3200#
adit 3500#
adit MSR#

adit 3104 (config)#
adit 3200 (config)#
adit 3500 (config)#
adit MSR (config)#

Use the logout command

Use the exit or end command.

Use the exit or end command, or
press Ctrl-z.

User Mode

In User Mode, the operator is allowed to view only limited information (not able to modify
configurations). Editing the configuration requires you to be in Privileged mode.

Privileged Mode

Privileged mode requires a password, and allows the operator to enter the Configuration mode.

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI 1-3

Introduction

Overview

Configuration Mode

z Allows users to configure specific features/functions.

z Use the configure terminal command to enter from Privileged mode.

z Identified by the (config)# prompt.

Note: As the submodes change, the words inside the parentheses are modified.

z To exit Configuration mode, type exit or press Ctrl-Z.

z Configuration mode has various submodes:

Configuration Mode Link to Command Prompt Displayed

Controller LCC controller lcc (config-cont-lcc-{n})#

Controller T1 controller t1 (config-cont-t1-{n})#

DHCP server pool ip dhcp pool ethernet (config-dhcp-eth-{n})#

Dial Peer FXS dial-peer voice pots fxs (config-dpeer-fxs)#

Dial Peer Trunk dial-peer voice pots trunk (config-dpeer-trk)#

Dial Peer VoIP dial-peer voice voip (config-dpeer-voip)#

Ethernet Interface interface ethernet (config-int-eth-{n})#

MLPPP Interface interface multilink (config-int-mlink-{n})#

Serial Interface interface serial (config-int-ser-{n})#

VPN IPSEC ipsec (config-ipsec)#

VPN L2TP Client l2tpc (config-l2tpc)#

OSPF router ospf (config-ospf)#

VPN PPTP Client pptpc (config-pptpc-{n})#

VPN PPTP Server pptps (config-pptps)#

RADIUS radius-client (config-radius)#

VLAN (Global) vlan (global) (config-vlan)#

VLAN (Port) vlan (vlan-id) (config-vlan-{n})#

Voice Port (Global) voice-port (global) (config-vport)#

Voice Port (FXS) voice-port fxs (config-vport-fxs-{n})#

Voice Port (Trunk) voice-port trunk (config-vport-trunk-{n})#

Voice Service SIP voice-service sip (config-voice-serv-sip)#

1-4 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

Introduction

Command Syntax Conventions

Command Syntax Conventions

The conventions used to present command syntax are as follows:

Convention Description

| Vertical bars separate alternative, mutually exclusive elements.

Example: (config)#

[ ] Square brackets indicate an optional element.

Example: (config)#

{ } Braces indicate a required choice.

Example: (config)#

Boldface Boldface indicated commands and keywords that are entered literally as shown. In actual

configuration examples and output (not general command syntax), boldface indicates commands
that are manually input by the user (i.e. show command).

Italics Italics indicates arguments for which you supply values.

clock source {1|2} {none|ds1 1|ds1 2|ds1 3|ds1 4}

event-history priority [error|fatal|info|notice|warning]

clock {1|2} source {none|t1 port}

Command Line Interface Help

During a CLI session, help is available.

Type a ? at a command line, to display help on the command:

Example: #?

? Display all commands

clear Clear command

configure Switch to Configure mode

copy Configures device database

debug Debug the system

end Exit to User mode

exit Exit to User mode

help Display all commands

history Display past entered commands

log Configure logging settings

no Disable a feature

reload Reboot the system

show Show various system information

upgrade Upgrade firmware from a local computer

#copy ?

defaults Restores default configuration

path Enter path to load configuration from

running-config Export current configuration

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI 1-5

Introduction

Shortcuts

Shortcuts

Keystroke Description

 Up Arrow

 

Left and Right Arrow

?

[Tab]

auto complete

Backspace

History

Use the up arrow key to re-display a previously entered command. Select the
up arrow repeatedly, to scroll through all the commands entered starting with
the most recent.

Will move curser one character to the left or right.

The question mark will display help for the current command.

Select the Tab key after entering a partial (but unique) portion of the CLI
command. This will result in the completion of a portion of the command
and will wait for further input.
Example:
(config)#sn [Tab]
(config)#snmp-server

You need only enter enough letters to identify a command as unique. For
example, entering cont t1 1 at the Global configuration prompt provides you
access to the configuration parameters for the specified T1 interface.
Entering controller t1 1 would work as well, but is not necessary.

Erases the character to the left.

The history shows up to a total of 100 commands. The history command will
show only the executed commands for the current mode/context.

[Ctrl+A]

[Ctrl+E]

[Ctrl+U]

[Ctrl+Z]

Moves the curser to the beginning of the command line.

Moves the curser to the end of the command line.

Clears the current displayed command line.

Exits from the current mode.

1-6 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

CHAPTER

2

User Mode

User mode is the first level of commands after logging in. User mode is represented by the >
prompt.

User Mode Commands

•date

•enable

•end

• exit

•help

•history

•ping

• show

• traceroute

User Mode

date

Use the date command to display the current date.

Syntax: > date

Example: adit 3500> date

Wed Jan 12 10:37:51 2007

enable

Use the enable command (at the User mode prompt) to enter the Privileged mode. Note: Once a correct
password has been entered, the prompt changes from ">" to "#".

Supported Platforms:

Syntax: > enable

Example: adit 3500> enable

password: ********

adit 3500#

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

Adit 3104, Adit 3200, Adit 3500, MSR

end

Use the end command to exit the current Configuration mode. Must be used to mark the end of any
configuration file. Note: This command can be entered in any Configuration mode with the same result.

Syntax: > end

Example: Adit 3500> end

Adit 3500 Username:admin
Adit 3500 Password:********

Supported Platforms:

2-2 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

Adit 3104, Adit 3200, Adit 3500, MSR

User Mode

exit

Use the exit command to close your current connection if you are in User mode or Privileged mode. If
the command is entered in a subconfiguration mode (Interface or Routing), this command takes you to
the previous level (example: back to Privileged mode from Interface configuration mode).

Syntax: > exit

Example: Adit 3500> exit

Adit 3500 Username:admin

Adit 3500 Password:********

help

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

Use the help command to display help information. This can also be accomplished with a ?. This
command can be entered in any Configuration mode.

Syntax: > help

or

> ?

Example: Adit 3500> help

? Display all commands

date Display time/date

enable Enter Privileged mode

end Logout from the device

exit Exit from the current level

help Display all commands

history Display past entered commands

ping Ping a remote host

show Show various system information

traceroute Traceroute to a remote host

Supported Platforms:

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI 2-3

Adit 3104, Adit 3200, Adit 3500, MSR

User Mode

history

Use the history command to display commands that have been entered in this session. This command
can be entered in any Configuration mode.

Syntax: > history

Example: Adit 3500> history

date

ping 192.168.1.1 -n 4

show version

show users

show voice-port fxs

ping 192.168.1.1

show version

history

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

2-4 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

User Mode

ping

Use the ping command to send a sequence of ICMP echo request packets to the specified host. If the
host variable is omitted, and you are in User mode, the router prompts you for additional information.
Note: The ping command verifies a connection, and is a very important troubleshooting tool.

Syntax: > ping {address [-i time] [-l size] [-n count]

[-w timeout]|stop}

Field Definition

address IP address of the host to ping.

-i time Specifies the intervals between pings.
Range is 0 - 600000 milliseconds.

-l size Specifies the size of the ping requests packets to be sent. Range 64 -

1518.

-n count Specifies the number of ping requests to be sent.
Range 1-1000. Default is 4.

-w timeout Specifies the time to wait for a response before sending the next ping
request packet. Timeout is given in seconds. Range 1-600000. Default
is 2 seconds.

stop Stop the ping process.

Example: Adit 3500>

ping 192.168.1.1

packet #1 has arrived

packet #2 has arrived

packet #3 has arrived

packet #4 has arrived

4 packets transmitted, 4 packets received

round-trip min/avg/max = 1/3/9 ms

Example: Adit 3500> ping 192.168.1.1 -n 2 -l 500

packet #1 has arrived

packet #2 has arrived

2 packets transmitted, 2 packets received

round-trip min/avg/max = 2/2/2 ms

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI 2-5

User Mode

show

show alarms show ip ospf database

show arp show ip ospf interface

show caclkcd show ip ospf neighbor

show config dynamic-dns show licenses

show controller lcc show log

show controller t1 show mac-address-table

show dhcp-leases show nat-fw

show digit-map show port-trigger

show interface description show route

show interface ethernet show service

show interface multilink show users

show interface serial show version

show interface stats show voice-port fxs

show ip ospf show voice-port trunk

2-6 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

User Mode

show alarms

Use the show alarms command to display the active alarms.

Syntax: > show alarms [t1 port|lcc number]

{alert|all|critical|info|major|minor}

Field Definition

t1 port Display alarms for a specific port.

Adit 3104: Value must be 1.
Adit 3500: Range = 1-4.

lcc number Display alarms for a specific Link Cross-Connect (LCC).

MSR: Range = 1-8.

alert Filter alert alarms (threshold crossing).

all Display all alarms.

critical Filter critical alarms.

info Filter information alarms.

major Filter major alarms.

minor Filter minor alarms.

Example: Adit 3500> show alarms all

Alarm Severity Time

Alarm LOS T1 4 Major Jan 1 00:00:08 2007

Alarm LOS T1 3 Major Jan 1 00:00:08 2007

Alarm PRI T1 2 - Line NOT Ready Major Jan 1 00:00:08 2007

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI 2-7

User Mode

show arp

Use the show arp command to display the ARP (Address Resolution Protocol) table.

Syntax: > show arp {all|address|ethernet port}

Field Definition

all Display entire ARP table.

address Display ARP items of the entered IP address.

ethernet port Display Ethernet ARP items only.

port - Define an Ethernet port number. Range 1 - 2.

Example: adit 3500> show arp ethernet 1

1 192.168.1.1 ether Dynam 00:50:da:59:f0:25 eth_lan

Example: adit 3500> show arp 192.168.1.1

ip=192.168.1.1 flags=Dynam mac=00:50:da:59:f0:25 iface=eth_lan

Example: adit 3500> show arp all

# IP-address HW-type Flags HW-address Iface

1 192.168.1.1 ether Dynam 00:50:da:59:f0:25 eth-1

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

2-8 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

User Mode

show caclkcd

Use the show caclkcd command to display the linux kernel crash dump

Syntax: > show caclkcd

Example: Adit 3500> show caclkcd

---------------- Begin cacLKCD -----------
Jan 1 2003 00:00:44 <3> openrg: unhandled page fault at pc=0x400528c0, lr=0x400
digit-map Show digit-map settings
52890 (bad address=0x30303038, code 245)Show various interfaces
pc : [<400528c0>] lr : [<40052890>] No Show l
r7 : 4006bb9c r6 : 30303038 r5 : 4006bb9c r4 : 4006bc1c
port-trigger
r3 : 30303030 r2 : 4006bc1c r1 : 4006bba5 r0 : 00000000
route Show routing table
Flags: nzCv IRQs on FIQs on Mode USER_32 Segment user Map the configurations to
CLI commands
User-mode stack:(0xbffffbac to 0xc0000000)
service Display services
fba0: 00000001 0036d238 003704d0 0036d238 003704d0their privilages
versio
fbc0: 003704d4 0002e1e0 00000001 003704d0 0002e1a8 00000004 00000005 000281d4
voice-port Show voice-port
fbe0: 4006d24d 4006d24c 4006d24c ffffffff 00000000 00rt Show
fce0: 00024324 00469c08 00000001 00025144 00469c08 00469c08 0009575c 40050458ip address
Ala

rm LOS T1#2
fd00: 002c85a0 000001e3 40e88bc0 00000000 00000000 00000000 0009574c 0036c448
exit
fd60: 0036e270 00000000 00000000 00000004 00000094 bffffdbc 00000004 40033490
fd80: 00000000 00000000 00000000 00000094 0011121c 0000008c bffffdbc 00263674
fda0: 00000bfd 0000008c 0011138c ffffffff ffffffff 00000007 00111c44 feedbabe
fdc0: 00001063 00033bb6 0000004e 00000000 00000023 002c81e8 4006b010 400335dc
fde0: 00000000 00000000 00000000 002c8188 401a430c 002c8188 00000023 002c81e8
fe00: 001df753 00000000 401a4494 4003f960 001df753 001df730 002c8188 001df753
fe20: 001df730 4006b010 401a5ae4 00000023 001df730 00000000 00000000 00000000
fe40: 00000000 00000000 0000009c 00000000 065ca5ac 00000002 0000009c 00000000
fe60: 057aacc3 00000000 00000000 40047924 00000020 401bb254 40032cf0 4002ead4
fe80: 00000020 400054d0 0000009c 00000000 05a4faa0 00000002 400051a8 0000c222
fea0: 00000000 40000ca4 00000000 00000000 00000000 400051a8 0000938c 00000000
fec0: 00000039 00282fac 0000bc4c 4000c848 00000000 40000ca4 bfffff34 bfffff3c
fee0: 00000001 00000704 bfffff3c 00000001 bfffff30 00000000 00000000 4006b010
ff00: 00000000 40051048 bfffff34 401bb458 0001f828 401967e4 00000000 00000000
ff20: 0001145c 00000000 40196814 00000000 00011474 bfffffd2 00000000 bfffffde
ff40: bfffffe5 00000000 00000010 00000097 00000006 00001000 00000011 00000064
ff60: 00000003 00008034 00000004 00000020 00000005 00000006 00000007 40000000
ff80: 00000008 00000000 00000009 0001145c 0000000b 00000000 0000000c 00000000
ffa0: 0000000d 00000000 0000000e 00000000 0000000f bfffffce 00000000 00000000
ffc0: 00000000 00000000 00000000 00007635 62002f62 696e2f6f 70656e72 6700484f
ffe0: 4d453d2f 00544552 4d3d6c69 6e757800 2f62696e 2f6f7065 6e726700 00000000

---------------- End cacLKCD -----------

Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI 2-9

User Mode

show config dynamic-dns

Use the show config dynamic-dns command to display the dynamic DNS configuration.

Syntax: > show config dynamic-dns

Example: Adit 3500> show config dynamic-dns

dynamic-dns username admin hostname Host1

dynamic-dns interface eth-2

no dynamic-dns offline enable

no dynamic-dns wildcard enable

no dynamic-dns backup-mx enable

no dynamic-dns mail-exchanger

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

show controller lcc

Use the show controller lcc command to display the settings for a Link Cross Connect on the MSR
card.

Syntax: > show controller lcc number

Field Definition

number Link Cross Connect number, 1-8.

Example: Adit MSR> show controller lcc 1

Settings for interface LCC 1

---------------------------

Name : LinkCC 1

Device Name : LinkCC 1

Status : Operational

Network : WAN

Connection Type : Link Cross Connect

Connection : Data

Alarm Reporting : Enabled

Supported Platforms: MSR

2-10 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

User Mode

show controller t1

Use the show controller t1 command to display the performance statistics of the DS1.

Syntax: > show controller t1 port

Field Definition

port DS1 (T1) interface.

Adit 3104 range = 1
Adit 3500 range 1-4

Example: Adit 3500> show controller t1 1

Settings for interface T1 1

---------------------------

Interface name : T1 1

Transmit status : Up

Receive status : Up

Framing : ESF

Clock source : Clock Reference 1

Line Code : B8ZS

Loop Detection : OFF

FDL Type : NONE

Line Length : DSX-1 equalization for 0-133ft

Status : Connected

Performance Threshold Settings 15 min 1 day

------ -----

unavailable seconds (uas): 0 0

severely errored seconds (ses): 0 0

errored seconds (es): 0 0

severely errored frame seconds (sefs): 0 0

line errored seconds (les): 0 0

controlled slip seconds (css): 0 0

bursty errored seconds (bes): 0 0

degraded minutes (dm): 0 0

line code violations (lcv): 0 0

path code violations (pcv): 0 0

Supported Platforms: Adit 3104, Adit 3200, Adit 3500

Not supported on the MSR

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI 2-11

User Mode

show dhcp-leases

Use the show dhcp-leases command to display the DHCP lease table.

Syntax: > show dhcp-leases

Example: Adit 3500> show dhcp-leases

Ethernet 1

Hostname : new-host IP:192.168.1.10 MAC:00:00:ff:ff:00:00
Type:static Expires-In:0

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

show digit-map

Use the show digit-map command to display the Digit Map settings.

Syntax: > show digit-map

Example: Adit 3500> show digit-map

Index Pattern

---------------------------------------------------------------

1 [2-9]11

2 [0-1][2-9]11

3 0[#T]

4 00

5 *xx

6 011x.[#T]

7 [0-1]xxxxxxx[#T]

8 [0-1][2-9]xxxxxxxxx

9 [2-9]xxxxxxxxx

10 [2-9]xxxxxx[#T]

Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR

2-12 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

User Mode

show interface description

Use the show interface description command to display interface information.

Syntax: > show interface description

Example: Adit 3500> show interface description

Device State IP/Mask Dependencies

T1 1 running None

T1 2 running None

T1 3 up None

T1 4 up None

Serial 1 up 0.0.0.0/255.255.255.255 T1 1

Ethernet 2 disabled 0.0.0.0/0.0.0.0 None

Ethernet 1 running 192.168.1.1/255.255.255.0 None

IPsec 0 disabled 0.0.0.0/0.0.0.0 Serial 1

IPsec 1 running 192.168.1.1/255.255.255.0 Ethernet 1

Example: Adit MSR> show interface description

Device State IP/Mask Dependencies

LinkCC 1 running None

LinkCC 2 running None

LinkCC 3 down None

LinkCC 4 down None

LinkCC 5 down None

LinkCC 6 down None

LinkCC 7 down None

LinkCC 8 down None

Ethernet 2 up DHCP Unassigned None

Ethernet 1 running 192.168.1.1/255.255.255.0 None

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI 2-13

User Mode

show interface ethernet

Use the show interface ethernet command to display the Ethernet interface information.

Syntax: > show interface ethernet port

Field Definition

port Ethernet port number. Range = 1-2.

Example: Adit 3500> show interface ethernet 1

Device=Ethernet 1 State=running IP/Mask=192.168.1.1/255.255.255.0

Dependency=None

Status: Connected; Link: 10T-HD

Tx (Packets/Bytes/Dropped/Errors)=(1620/1643674/0/0)

Rx (Packets/Bytes/Dropped/Errors)=(1636/143050/0/0)

Broadcasts (Tx/Rx)=(0/0) Multicasts=0 Collisions=0

Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR

show interface multilink

Use the show interface multilink command to display the multilink configuration information.

Syntax: > show interface multilink port

Field Definition

port Multilink port number.

Adit 3104, Adit 3200, Adit 3500: Value must be 1.
MSR: Range is 1-8

Example: Adit 3500> show interface multilink 1

Device=mlink-1 State=down IP/Mask=Unnumbered

Dependency=t1-1,t1-3

Status: Disconnected

Example: Adit MSR> show interface multilink 1

Device=mlink-1 State=down IP/Mask=Unnumbered

Dependency=LCC1,LCC2

Status: Disconnected

Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR

2-14 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

User Mode

show interface serial

Use the show interface serial command to display the configuration of the serial interface.

Syntax: > show interface serial port

Field Definition

port Serial interface.

Adit 3104: Value must be 1.
Adit 3500: Range = 1-4.
MSR: Range = 1-8.

Example: Adit 3500> show interface serial 3

Device=Serial 1 State=up IP/Mask=0.0.0.0/255.255.255.255

Dependency=T1 1

Status: Reconnecting...

Tx (Packets/Bytes/Dropped/Errors)=(3332/39984/0/0)

Rx (Packets/Bytes/Dropped/Errors)=(0/0/0/0)

Example: Adit MSR> show interface serial 3

Device=Serial 1 State=up IP/Mask=0.0.0.0/255.255.255.255

Dependency=LCC1

Status: Reconnecting...

Tx (Packets/Bytes/Dropped/Errors)=(3332/39984/0/0)

Rx (Packets/Bytes/Dropped/Errors)=(0/0/0/0)

Supported Platforms: Adit 3104, Adit 3500, MSR

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI 2-15

User Mode

show interface stats

Use the show interface stats command to display the interface statistics.

Syntax: > show interface stats

Example: Adit 3500> show interface stats

Device=T1 1 State=up Dependency=None Status: Connecting (Alarm Condition)

Device=T1 2 State=up Dependency=None Status: Connecting (Alarm Condition)

Device=T1 3 State=running Dependency=None Status: Connected

Device=T1 4 State=running Dependency=None Status: Connected

Device=Serial 1 State=down IP/Mask=0.0.0.0/255.255.255.255 Dependency=T1 1 Status: Disconnected

Device=Ethernet 2 State=disabled IP/Mask=192.168.2.10/255.255.255.0 Dependency=None

Device=Ethernet 1 State=running IP/Mask=192.168.1.35/255.255.255.0 Dependency=None Status: Connected; Link: 10T-HD

Tx (Packets/Bytes/Dropped/Errors)=(2362/2498024/0/0)

Rx (Packets/Bytes/Dropped/Errors)=(2211/210493/0/0)

Broadcasts (Tx/Rx)=(0/0) Multicasts=0 Collisions=0

Device=IPsec 0 State=disabled IP/Mask=0.0.0.0/0.0.0.0 Dependency=Serial 1

Device=IPsec 1 State=running IP/Mask=192.168.1.35/255.255.255.0 Dependency=Ethernet 1Status: Connected

Tx (Packets/Bytes/Dropped/Errors)=(0/0/0/0)

Rx (Packets/Bytes/Dropped/Errors)=(0/0/0/0)

Example: Adit MSR> show interface stats

Device=LinkCC 1 State=running

Dependency=None

Status: Operational

Device=LinkCC 2 State=running

Dependency=None

Status: Operational

Device=LinkCC 3 State=down

Dependency=None

Status: Unassigned

Device=LinkCC 4 State=down

Dependency=None

Status: Unassigned

Device=LinkCC 5 State=down

Dependency=None

Status: Unassigned

Device=LinkCC 6 State=down

Dependency=None

Status: Unassigned

Device=LinkCC 7 State=down

Dependency=None

2-16 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

User Mode

Status: Unassigned

Device=LinkCC 8 State=down

Dependency=None

Status: Unassigned

Device=Ethernet 2 State=up IP/Mask=DHCP Unassigned

Dependency=None

Status: DHCP IP Address Released; Link: Down

Tx (Packets/Bytes/Dropped/Errors)=(0/0/0/0)

Rx (Packets/Bytes/Dropped/Errors)=(0/0/0/0)

Broadcasts (Tx/Rx)=(0/0) Multicasts=0 Collisions=0

Device=Ethernet 1 State=running IP/Mask=10.0.0.3/255.255.255.0

Dependency=None

Status: Connected; Link: 10T-HD

Tx (Packets/Bytes/Dropped/Errors)=(1509/1577037/0/0)

Rx (Packets/Bytes/Dropped/Errors)=(1540/119409/0/0)

Broadcasts (Tx/Rx)=(0/0) Multicasts=0 Collisions=0

Supported Platforms:Adit 3104, Adit 3200, Adit 3500, MSR

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI 2-17

User Mode

show ip ospf

Use the show ip ospf command to display the general OSPF routing process information.

Syntax: > show ip ospf

Example: adit 3500> show ip ospf

Routing Process "ospf 0" with ID 192.168.1.1

Process uptime is 28 minutes

Process bound to VRF default

Conforms to RFC2328, and RFC1583Compatibility flag is disabled

Supports only single TOS(TOS0) routes

Supports opaque LSA

Supports Graceful Restart

SPF schedule delay 5 secs, Hold time between two SPFs 10 secs

Refreshtimer 10 secs

Number of incoming current DD exchange neighbors 0/5

Number of outgoing current DD exchange neighbors 0/5

Number of external LSA 0. Checksum 0x000000

Number of opaque AS LSA 0. Checksum 0x000000

Number of router LSA 0

Router LSA database is unlimited.

Number of network LSA 0

Network LSA database is unlimited.

Number of non-default summary LSA 0

Summary LSA database is unlimited.

Number of asbr summary LSA 0

ASBR Summary LSA database is unlimited.

Number of non-default external LSA 0

External LSA database is unlimited.

Number of LSA originated 0

Number of LSA received 0

Number of areas attached to this router: 0

Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR

2-18 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

User Mode

show ip ospf database

Use the show ip ospf database command to display information related to the OSPF database for
a specific router. The various forms of this command deliver information on defined OSPF link
state advertisements.

Syntax: > show ip ospf database {setting}

Syntax: > show ip ospf database {adv-router address|self-originate}

Syntax: > show ip ospf database network link-state-id

Syntax: > show ip ospf database router {link-state-id|adv-router

address|self-originate}

Syntax: > show ip ospf database summary [link-state-id] [adv-router

address|self-originate]

Field Definition

adv-router address Displays all the LSAs of the specified router. If no IP address is

entered, the local router information will be displayed (same as self­originate).

link-state-id Portion of the Internet environment that is being described by the

advertisement. The value entered depends on the advertisement's LS
type. It must be entered in the form of an IP address. When the link
state advertisement is describing a network, the link-state-id can take
one of two forms:

1. The network's IP address (as in type 3 summary link advertisements
and in autonomous system external link advertisements).

2. A derived address obtained from the link state ID. (Note that
masking a network links advertisement's link state ID with the
network's subnet mask yields the network's IP address.)
When the link state advertisement is describing a router, the link state
ID is always the described router's OSPF router ID.
When an autonomous system external advertisement (LS Type = 5) is
describing a default route, its link state ID is set to Default Destination
(0.0.0.0).

network Displays information only about the network LSAs.

router Displays information only about the Router LSAs.

self-originate Displays only self-originated LSAs (from the local router).

summary Displays information on.ly about the summary LSAs.

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI 2-19

User Mode

Example: adit 3500> show ip ospf database

Router Link States (Area 0.0.0.1)

Link ID ADV Router Age Seq# CkSum Link count

192.168.3.1 192.168.3.1 313 0x800000c1 0x4978 1

192.168.3.255 192.168.3.255 568 0x8000003a 0xa6c0 1

Net Link States (Area 0.0.0.1)

Link ID ADV Router Age Seq# CkSum

192.168.3.251 192.168.3.255 388 0x80000003 0xbcec

Example: adit 3500> show ip ospf database self-originate

Router Link States (Area 0.0.0.1)

Link ID ADV Router Age Seq# CkSum Link count

192.168.3.255 192.168.3.255 420 0x8000003a 0xa6c0 1

Net Link States (Area 0.0.0.1)

Link ID ADV Router Age Seq# CkSum

192.168.3.251 192.168.3.255 240 0x80000003 0xbcec

Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR

2-20 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

User Mode

show ip ospf interface

Use the show ip ospf interface command to display OSPF related interface information.

Syntax: > show ip ospf interface {ethernet port|serial port|multilink

port}

Field Definition

ethernet port Display information on the Ethernet interface.

port = 1 or 2

serial port Display information on the serial interface.

Adit 3104: Value must be 1.
Adit 3500: Range = 1-4.
MSR: Range = 1-8.

multilink port Display information on the Multilink interface.

Adit 3104, Adit 3500, MSR: Value must be 1

Example: adit 3500> show ip ospf interface ethernet 1

Ethernet 1 is up, line protocol is up

Internet Address 192.168.254.202, Mask 255.255.255.0, Area 0.0.0.0

AS 201, Router ID 192.168.99.1, Network Type BROADCAST, Cost: 10

Transmit Delay is 1 sec, State OTHER, Priority 1

Designated Router id 192.168.254.10, Interface address 192.168.254.10

Backup Designated router id 192.168.254.28, Interface addr 192.168.254.28

Timer intervals configured, Hello 10, Dead 60, Wait 40, Retransmit 5

Hello due in 0:00:05

Neighbor Count is 8, Adjacent neighbor count is 2

Adjacent with neighbor 192.168.254.28 (Backup Designated Router)

Adjacent with neighbor 192.168.254.10 (Designated Router)

Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI 2-21

User Mode

show ip ospf neighbor

Use the show ip ospf neighbor command to display OSPF neighbor information.

Syntax: > show ip ospf neighbor [interface address|neighbor-id|detail]

Field Definition

interface address Optional parameter. Enter interface IP address to define display.

neighbor-id Optional parameter. Enter neighbor IP address to define display.

detail Optional parameter. Enable display of detailed information.

Example: adit 3500> show ip ospf neighbor

ID Pri State Dead Time Address Interface

10.199.199.137 1 FULL/DR 0:00:31 192.168.80.37 Ethernet1

172.16.48.1 1 FULL/DROTHER 0:00:33 172.16.48.1 Fddi0

172.16.48.200 1 FULL/DROTHER 0:00:33 172.16.48.200 Fddi0

10.199.199.137 5 FULL/DR 0:00:33 172.16.48.189 Fddi0

Example: adit 3500> show ip ospf neighbor 10.199.199.137

Neighbor 10.199.199.137, interface address 192.168.80.37

In the area 0.0.0.0 via interface Ethernet0

Neighbor priority is 1, State is FULL

Options 2

Dead timer due in 0:00:32

Link State retransmission due in 0:00:04

Neighbor 10.199.199.137, interface address 172.16.48.189

In the area 0.0.0.0 via interface Fddi0

Neighbor priority is 5, State is FULL

Options 2

Dead timer due in 0:00:32

Link State retransmission due in 0:00:03

Example: adit 3500> show ip ospf neighbor detail

Neighbor 192.168.5.2, interface address 10.225.200.28

In the area 0 via interface GigabitEthernet1/0/0

Neighbor priority is 1, State is FULL, 6 state changes

DR is 10.225.200.28 BDR is 10.225.200.30

Options is 0x42

LLS Options is 0x1 (LR), last OOB-Resync 00:03:08 ago

Dead timer due in 00:00:36

Neighbor is up for 00:09:46

Index 1/1, retransmission queue length 0, number of retransmission 1

First 0x0(0)/0x0(0) Next 0x0(0)/0x0(0)

Last retransmission scan length is 1, maximum is 1

Last retransmission scan time is 0 msec, maximum is 0 msec

Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR

2-22 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

User Mode

show licenses

Use the show licenses command to display all enabled feature keys.

Syntax: > show licenses

Example: Adit 3500> show licenses

VPN license = No

SIP license = Yes

MGCP license = No

G729A license = Yes

Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR

show log

Use the show log command to display the current events on the system.

Syntax: > show log {firewall|pri|sip|system|t1 port|lcc number}

{severity}

Field Definition

firewall Filter firewall alarms

pri Display PRI logs. Note: This is not supported on the Adit 3104.

sip Display SIP logs.

system Filter general system alarms

t1 port Display event log for a specific T1 port.

Adit 3104: Value must be 1.
Adit 3500: Range = 1-4.

lcc number Display event log for a specific Link Cross-Connect (LCC).

MSR: Range = 1-8.

severity alert - Filter alert alarms (threshold crossing)

all - Display all alarms
critical - Filter critical alarms (service affecting)
info - Filter informational alarms
major - Filter major alarms (service affecting)
minor - Filter minor alarms (non-service affecting)

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI 2-23

User Mode

Example: Adit 3500> show log t1 1 minor

System Log Message Jan 1 00:00:08 2003 kern.err T1 ALARM: Alarm LOS T1#1 Major received
System Log Message Jan 1 00:00:04 2003 kern.err T1 ALARM: Alarm LOS T1#1 Major received
System Log Message Jan 1 01:19:13 2003 kern.err T1 ALARM: Alarm LOS T1#1 Major received
System Log Message Jan 1 00:57:12 2003 kern.err T1 ALARM: Alarm LOS T1#1 Major received
System Log Message Jan 1 00:56:52 2003 kern.err T1 ALARM: Alarm LOS T1#1 Major received
System Log Message Jan 1 00:56:34 2003 kern.err T1 ALARM: Alarm LOS T1#1 Major received
System Log Message Jan 1 00:56:09 2003 kern.err T1 ALARM: Alarm LOS T1#1 Major received
System Log Message Jan 1 00:00:04 2003 kern.err T1 ALARM: Alarm LOS T1#1 Major received

Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR

show mac-address-table

Use the show mac-address-table command to display the current MAC addresses (LAN\WAN).

Syntax: > show mac-address-table

Example: Adit 3500> show mac-address-table

Ethernet 1 mac= 00:00:00:ff:ff:ff

Ethernet 2 mac= 00:00:00:ff:ff:fd

Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR

2-24 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

User Mode

show nat-fw

Use the show nat-fw command to display the current NAT and firewall connection table.

Syntax: > show nat-fw

Example: Adit 3500> show nat-fw

Number Content

1 TCP 11.0.0.4 36104<--> 172.15.16.1 36104[31.0.0.6 5516 ]
TIME_WAIT/TIME_WAIT ttl 0 sec bytes 1320 pkts 7 ppp100 Outgoing BY FTP

2 TCP 11.0.0.4 36103<--> 172.15.16.1 36103[31.0.0.6 21 ]
TIME_WAIT/TIME_WAIT ttl 0 sec bytes 1182 pkts 20 FTP child: Yes ppp100 Outgoing

3 TCP 11.0.0.4 36102<--> 172.15.16.1 36102[31.0.0.6 5515 ]
TIME_WAIT/TIME_WAIT ttl 0 sec bytes 1320 pkts 7 ppp100 Outgoing BY FTP

4 TCP 11.0.0.4 36101<--> 172.15.16.1 36101[31.0.0.6 21 ]
TIME_WAIT/TIME_WAIT ttl 0 sec bytes 1182 pkts 20 FTP child: Yes ppp100 Outgoing

5 UDP 172.15.16.2 28015<--> 172.15.16.2 28015[*.*.*.* *]
ttl 79 sec bytes 0 pkts 0 ppp100 Outgoing CLONABLE UNINIT BY SIP

6 UDP 172.15.16.2 28014<--> 172.15.16.2 28014[*.*.*.* *]
ttl 79 sec bytes 0 pkts 0 ppp100 Outgoing CLONABLE UNINIT BY SIP

7 UDP 172.15.16.2 28013<--> 172.15.16.2 28013[*.*.*.* *]
ttl 77 sec bytes 0 pkts 0 ppp100 Outgoing CLONABLE UNINIT BY SIP

8 UDP 172.15.16.2 28012<--> 172.15.16.2 28012[*.*.*.* *]
ttl 77 sec bytes 0 pkts 0 ppp100 Outgoing CLONABLE UNINIT BY SIP

9 UDP 172.15.16.2 28011<--> 172.15.16.2 28011[*.*.*.* *]
ttl 75 sec bytes 0 pkts 0 ppp100 Outgoing CLONABLE UNINIT BY SIP

10 UDP 172.15.16.2 28010<--> 172.15.16.2 28010[*.*.*.* *]
ttl 75 sec bytes 0 pkts 0 ppp100 Outgoing CLONABLE UNINIT BY SIP

Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI 2-25

User Mode

show port-trigger

Use the show port-trigger command to display all port triggering information.

Syntax: > show port-trigger

Example: Adit 3500> show port-trigger

Service ID:134217730 Enable Service Name:L2TP
Trigger protocol: UDP port: src_start=0 src_end=0 dst_start=1701 dst_end=1701

Service ID:16777223 Enable Service Name:TFTP
Trigger protocol: UDP port: src_start=1024 src_end=65535 dst_start=69 dst_end=69

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

show route

Use the show route command to display the routing table.

Syntax: > show route

Example: Adit 3500> show route

Destination Gateway Flags Metric Interface

192.168.1.0/24 * U 50 Ethernet 1

192.168.1.0/24 * U 51 IPsec 1

Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR

2-26 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

User Mode

show service

Use the show service command to displays all services.

Syntax: > show service

Example: Adit 3500> show service

Group: Basic Web Utilities
Service ID:16777216 Service Name:All Traffic
Trigger protocol: NO PROTOCOL port: src_start=0 src_end=0 dst_start=0 dst_end=0

Service ID:16777217 Service Name:DNS
Trigger protocol: TCP port: src_start=53 src_end=53 dst_start=53 dst_end=53

Service ID:16777217 Service Name:DNS
Trigger protocol: TCP port: src_start=1024 src_end=65535 dst_start=53 dst_end=53

Service ID:16777217 Service Name:DNS
Trigger protocol: UDP port: src_start=53 src_end=53 dst_start=53 dst_end=53

Service ID:16777217 Service Name:DNS
Trigger protocol: UDP port: src_start=1024 src_end=65535 dst_start=53 dst_end=53

Service ID:16777218 Service Name:FTP
Trigger protocol: TCP port: src_start=0 src_end=0 dst_start=21 dst_end=21

Service ID:16777219 Service Name:HTTP

.

.

.

Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI 2-27

User Mode

show users

Use the show users command to displays all users on this system.

Syntax: > show users

Example: Adit 3500> show users

Provisioned User List

User-1 : admin Access: ADMIN <-

User-2 : pauljones Access: ADMIN

Active CLI Users

User-1 : admin Access:ADMIN Authen:Config from IP:192.168.1.1

User-2 : admin Access:ADMIN Authen:Config from Console

Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR

show version

Use the show version command to displays the version for the hardware, software and firmware.
The Admin level user will be provided with more information than Manager and Monitor levels.
Software features are listed along with enabled status.

Syntax: > show version

Example: Adit 3500> show version

Application Version: 1.4.0

Compilation Time: Thu Jul 20 2006 13:48:42

FPGA Version: 1.0.0

Board Version: 1 003-1215-0100

IXP400 Software Release: 1_4 SQA4_1

MSP:

82530 - 60 channels

Image File Name: TGW_v5_03_cdma.axf

API Version : 2.1.0

Source IP Addr : 192.168.1.1

Voice Slot 1 : FXS Card Present: Rev 5.00 VIP

Vendor: Turin Networks

CLEI Code: IPMHX00LRA

Product Features:

SIP enabled.

G729A enabled.

2-28 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

User Mode

Example: Adit MSR> show version

Application Version: 2.0.0.5

Compilation Time: Thu Jan 31 2008 13:48:42

FPGA Version: 0.04

Boot Version: 1.14

Board Version: 0 003-1756-0001

Flash Size: 32M bytes

Memory Size: 64M bytes

IXP400 Software Release: 1_4 SQA4_1

MSP:

82610 - 100 channels

Image File Name: TGW_v5_05.axf

API Version : 2.1.0

Source IP Addr : 10.10.4.202

MSR Card Slot: 5

CLEI Code: SITRAANBAA

Product Features:

VPN enabled.

SIP enabled.

Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI 2-29

User Mode

show voice-port fxs

Use the show voice-port fxs command to display the FXS interface information.

Syntax: > show voice-port fxs

Example: Adit 3500> show voice-port fxs

Registration Address: 172.32.1.15

SIP Proxy: Yes

Proxy Address: 172.32.1.18

* Line UID PhoneStatus RegisStatus RX/TX/Lost(Pkts) Jitter Overflow

----------------------------------------------------------------------------

Y 1 3035550001 Idle Registered

Y 2 3035550002 Idle Registered

Y 3 3035550003 Idle Registered

Y 4 3035550004 Idle Registered

Example: Adit MSR> show voice-port fxs

Registration Address: 172.32.1.15

SIP Proxy: Yes

Proxy Address: 172.32.1.18

* Line UID PhoneStatus RegisStatus RX/TX/Lost(Pkts) Jitter Overflow CrossConnect

------------------------------------------------------------------------------------------

Y 1 3035550001 Idle Registered Connected

Y 2 3035550002 Idle Registered Connected

Y 3 3035550003 Idle Registered Connected

Y 4 3035550004 Idle Registered Connected

Y 5 3035550005 Idle Registered Connected

Y 6 3035550006 Idle Registered Connected

Y 7 3035550007 Idle Registered Connected

Y 8 3035550008 Idle Registered Connected

.

.

.

Supported Platforms: Adit 3104, Adit 3500, MSR

2-30 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

User Mode

show voice-port trunk

Use the show voice-port trunk command to display the voice trunk statistics.

Syntax: > show voice-port trunk port

Field Definition

port Adit 3500: DS1 (T1) interface. Value must be 1.

MSR: Link Cross Connect (LCC). Range = 1-8.

Example: Adit 3500> show voice-port trunk 1

trunk-1 t1-1 does not exist

******************************* CAS 2 *************************************

Channel no Internal Call Id Q931 Connection Id Tdm TimeSlot Call State

-------------------------------------------------------------------------------

1 -1 -1 -1 INACTIVE

2 -1 -1 -1 INACTIVE

3 -1 -1 -1 INACTIVE

4 -1 -1 -1 INACTIVE

5 -1 -1 -1 INACTIVE

6 -1 -1 -1 INACTIVE

7 -1 -1 -1 INACTIVE

8 -1 -1 -1 INACTIVE

9 -1 -1 -1 INACTIVE

10 -1 -1 -1 INACTIVE

11 -1 -1 -1 INACTIVE

12 -1 -1 -1 INACTIVE

13 -1 -1 -1 INACTIVE

14 -1 -1 -1 INACTIVE

15 -1 -1 -1 INACTIVE

16 -1 -1 -1 INACTIVE

17 -1 -1 -1 INACTIVE

18 -1 -1 -1 INACTIVE

19 -1 -1 -1 INACTIVE

20 -1 -1 -1 INACTIVE

21 -1 -1 -1 INACTIVE

22 -1 -1 -1 INACTIVE

23 -1 -1 -1 INACTIVE

24 -1 -1 -1 INACTIVE

trunk-1 t1-3 does not exist

trunk-1 t1-4 does not exist

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI 2-31

User Mode

Example: Adit MSR> show voice-port trunk 1

******************************* PRI 1 ***************************************

Channel no Internal Call Id Q931 Connection Id Tdm TimeSlot Call State

-------------------------------------------------------------------------------

1 -1 -1 -1 INACTIVE

2 -1 -1 -1 INACTIVE

3 -1 -1 -1 INACTIVE

4 -1 -1 -1 INACTIVE

5 -1 -1 -1 INACTIVE

6 -1 -1 -1 INACTIVE

7 -1 -1 -1 INACTIVE

8 -1 -1 -1 INACTIVE

9 -1 -1 -1 INACTIVE

10 -1 -1 -1 INACTIVE

11 -1 -1 -1 INACTIVE

12 -1 -1 -1 INACTIVE

13 -1 -1 -1 INACTIVE

14 -1 -1 -1 INACTIVE

15 -1 -1 -1 INACTIVE

16 -1 -1 -1 INACTIVE

17 -1 -1 -1 INACTIVE

18 -1 -1 -1 INACTIVE

19 -1 -1 -1 INACTIVE

20 -1 -1 -1 INACTIVE

21 -1 -1 -1 INACTIVE

22 -1 -1 -1 INACTIVE

23 -1 -1 -1 INACTIVE

trunk 1 LCC#2 does not exist

trunk 1 LCC#3 does not exist

trunk 1 LCC#4 does not exist

trunk 1 LCC#5 does not exist

trunk 1 LCC#6 does not exist

trunk 1 LCC#7 does not exist

trunk 1 LCC#8 does not exist

Supported Platforms: Adit 3500, MSR

2-32 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

User Mode

traceroute

Use the traceroute command to trace a route to a remote host.

Syntax: > traceroute

Syntax: > traceroute {address|hostname|stop}

Field Definition

address IP address of the remote host.

hostname Host name of the remote host.

stop Stop the traceroute process.

Example: Adit 3500> traceroute to 192.168.1.200

(192.168.1.200), 10 hops max

1 192.168.1.200 (192.168.1.200) 10.500 ms 1.013 ms 0.926 ms

Traceroute: Destination Reached

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI 2-33

User Mode

2-34 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

CHAPTER

Privileged Mode

The Privileged Mode allows the operator access to the configuration modes.

This Mode is entered with the > enable command from the Basic mode.

The Privileged Mode is represented by the # prompt.

Privileged Mode Commands

3

• clear

• configure terminal

• copy

•date

• debug

•end

• exit

•help

•history

• log clear

• no debug

•ping

•reload

• show

• traceroute

• upgrade

Privileged Mode

clear

clear arp

Use the clear arp command to clear the ARP (Address Resolution Protocol) table.

Syntax: # clear arp {all|ethernet port|address}

Example: adit 3500# clear arp ethernet 1

Field Definition

all Display entire ARP table.

ethernet port Display Ethernet ARP items only.

port - Define an Ethernet port number. Range 1 - 2.

address Enter IP address for specific ARP information on this address.

arp entries removed on eth-1 interface

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

clear caclkcd

Use the clear arp command to clear the linux kernel crash dump.

Syntax: # clear caclkcd

Example: adit 3500# clear caclkcd

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

clear ip ospf process

Use the clear ip ospf process command to restart the OSPF process with the LSA databases and
counters reinitialized.

Syntax: # clear ip ospf process

Example: adit 3500# clear ip ospf process

Supported Platforms:

3-2 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

Adit 3104, Adit 3200, Adit 3500, MSR

Privileged Mode

configure terminal

Use the configure terminal command to enter the configuration mode.

Syntax: # configure terminal

Example: adit 3500# configure terminal

adit 3500 (config)#

copy

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

copy defaults

Use the copy defaults command to restore default setting.

Syntax: # copy defaults running-config

Example: adit 3500# copy defaults running-config

Going to reboot!
Restarting system.

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

copy path

Use the copy path command to load a configuration saved on your computer to the Adit system.
Note: A TFTP server must be running on your computer.

Syntax: # copy path {source-path} running-config

Field Definition

source-path Enter the source path, in the form tftp://address/filename

address - Enter IP address of the TFTP server.
filename - Enter the name of the configuration file to load onto the

system.

Example: adit 3500# copy path tftp://192.168.1.100/a3500_config running-

config

adit 3500#Configuration restore: Success

WARNING: A reload is needed for changes to take effect.

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI 3-3

Privileged Mode

Example: Adit MSR#copy path tftp://192.168.1.100/MSR_config running-

config

Adit MSR#Configuration restore: Success.

WARNING: A reload is needed for changes to take effect.

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

copy running-config

Use the copy running-config command to save the current configuration on the Adit.
Note: The TFTP server must be running on the destination device.

Syntax: # copy running-config path {destination-path}

Field Definition

destination-path Enter the destination path, in the form tftp://address/filename to the

location where the configuration file is to be saved.

address - Enter IP address of the TFTP server.
filename - Enter a name for this new configuration file.

Example: adit 3500# copy running-config path tftp://192.168.1.100/

a3500_config

adit 3500# Configuration save: Success

Example: Adit MSR#copy running-config path tftp://192.168.1.100/

testconfig

Adit MSR#Configuration save: Success

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

date

Use the date command to display the current date.

Syntax: # date

Example: Adit 3500# date

Wed Jan 12 10:37:51 2007

Supported Platforms:

3-4 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

Adit 3104, Adit 3200, Adit 3500, MSR

Privileged Mode

debug

debug portmon all

Use the debug portmon all command allows the user to monitor all traffic of a specific type. All
traffic can be displayed, or a specific traffic type can be defined. Note: Immediately after this
command is issued, any traffic that falls into the filter parameter will be displayed. To turn the
monitoring off, you must issue a no debug portmon command. See no debug portmon command
on page 3-16.

Syntax: # debug portmon all [all|arp address|bootp address|control

|data|dns address|icmp address|ip address|link|mgcp address|
rip address|sip address|stp|tcp {address|address:port|port}|
udp {address|address:port|port}]

Field Definition

Filters all traffic of the following type.

all Allows all traffic.

arp Displays all Address Resolution Protocol traffic.

address = IP address of the interface.

bootp Displays BootP related traffic.

address = IP address of the interface.

control Displays control related traffic.

data Displays data related traffic.

dns Displays Domain Naming Service related traffic.

address = IP address of the interface.

icmp Displays Internet Control Message Protocol related traffic.

address = IP address of the interface.

ip Displays Internet Protocol related traffic Note: Requires an IP address.

address = IP address of the interface.

link Displays link related traffic.

mgcp Displays Media Gateway Control Protocol related traffic.

address = IP address of the interface.

rip Displays Routing Information Protocol related traffic.

address = IP address of the interface.

sip Displays Session Initiation Protocol related traffic.

address = IP address of the interface.

stp Displays Spanning Tree Protocol related traffic.

tcp Displays Transmission Control Protocol related traffic.

address = IP address of the interface.
address:port = IP address
port = Port of the interface

udp Displays User Datagram Protocol related traffic.

address = IP address of the interface.
address:port = IP address:port of the interface.
port = Port of the interface

Example: adit 3500# debug portmon all rip 192.168.1.20

Supported Platforms:

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI 3-5

Adit 3104, Adit 3200, Adit 3500, MSR

Privileged Mode

debug portmon {rx|tx|both}

Use the debug portmon {rx|tx|both} command allows the user to monitor specific direction of
traffic.
Note: Immediately after this command is issued, any traffic that falls into the filter parameter will
be displayed. To turn the monitoring off, you must issue a no debug portmon command. See no
debug portmon command on page 3-16.

Syntax: # debug portmon {rx|tx|both}

Example: adit 3500# debug portmon both

Field Definition

both Display both receive and transmit information.

rx Display the receive direction.

tx Display the transmit direction.

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

debug portmon detail

Use the debug portmon detail command allows the user to configure the portmon to display brief
information or detailed. See no debug portmon command on page 3-16.

Syntax: # debug portmon detail {off|on}

Field Definition

off Disables detail packet display

on Enable detailed packet display

Example: adit 3500# debug portmon detail on

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

3-6 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

Privileged Mode

debug portmon ethernet

Use the debug portmon ethernet command allows the user to monitor specific Ethernet traffic.
Note: Immediately after this command is issued, any traffic that falls into the filter parameter will

be displayed. To turn the monitoring off, you must issue a no debug portmon command. See no
debug portmon command on page 3-16.

Syntax: # debug portmon ethernet {1|2|both} [all|arp address|bootp

address|control|data|dns address|icmp address|ip address|link|
mgcp address|rip address|sip address|stp|tcp {address|
address:port|port}|udp {address|address:port|port}]

Field Definition

ethernet Display Ethernet traffic.

1 or 2 - Define Ethernet port
both - Both Ethernet ports

Filters all traffic of the following type.

all Allows all traffic.

arp Displays all Address Resolution Protocol traffic.

address = IP address of the interface.

bootp Displays BootP related traffic.

address = IP address of the interface.

control Displays control related traffic.

data Displays data related traffic.

dns Displays Domain Naming Service related traffic.

address = IP address of the interface.

icmp Displays Internet Control Message Protocol related traffic.

address = IP address of the interface.

ip Displays Internet Protocol related traffic Note: Requires an IP address.

address = IP address of the interface.

link Displays link related traffic.

mgcp Displays Media Gateway Control Protocol related traffic.

address = IP address of the interface.

rip Displays Routing Information Protocol related traffic.

address = IP address of the interface.

sip Displays Session Initiation Protocol related traffic.

address = IP address of the interface.

stp Displays Spanning Tree Protocol related traffic.

tcp Displays Transmission Control Protocol related traffic.

address = IP address of the interface.
address:port = IP address
port = Port of the interface

udp Displays User Datagram Protocol related traffic.

address = IP address of the interface.
address:port = IP address:port of the interface.
port = Port of the interface

Example: adit 3500# debug portmon ethernet 1 all

Supported Platforms:

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI 3-7

Adit 3104, Adit 3200, Adit 3500, MSR

Privileged Mode

debug portmon management

Use the debug portmon management command allows the user to configure management trace
suppression. See no debug portmon command on page 3-16.

Syntax: # debug portmon management {hush|off}

Example: adit 3500# debug portmon management hush

Field Definition

hush hush - Enable suppression of management traffic trace

off off - Disable suppression of management traffic trace

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

3-8 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

Privileged Mode

debug portmon multilink

Use the debug portmon multilink command allows the user to monitor the multilink traffic. All
traffic can be displayed, or a specific traffic type can be defined.
Note: Immediately after this command is issued, any traffic that falls into the filter parameter will
be displayed. To turn the monitoring off, you must issue a no debug portmon command. See no
debug portmon command on page 3-16

Syntax: # debug portmon multilink port {all|arp address|bootp

address|control|data|dns address|icmp address|ip address
|link|mgcp address|rip address|sip address|stp|tcp {address|
address:port|port}|udp {address|address:port|port}}

Field Definition

port Enter multilink port. Range 1.

all Allows all traffic.

arp Displays all Address Resolution Protocol traffic.

address = IP address of the interface.

bootp Displays BootP related traffic.

address = IP address of the interface.

control Displays control related traffic.

data Displays data related traffic.

dns Displays Domain Naming Service related traffic.

address = IP address of the interface.

icmp Displays Internet Control Message Protocol related traffic.

address = IP address of the interface.

ip Displays Internet Protocol related traffic Note: Requires an IP address.

address = IP address of the interface.

link Displays link related traffic.

mgcp Displays Media Gateway Control Protocol related traffic.

address = IP address of the interface.

rip Displays Routing Information Protocol related traffic.

address = IP address of the interface.

sip Displays Session Initiation Protocol related traffic.

address = IP address of the interface.

stp Displays Spanning Tree Protocol related traffic.

tcp Displays Transmission Control Protocol related traffic.

address = IP address of the interface.
address:port = IP address
port = Port of the interface

udp Displays User Datagram Protocol related traffic.

address = IP address of the interface.
address:port = IP address:port of the interface.
port = Port of the interface

Example: adit 3500# debug portmon multilink 1 mgcp 192.168.1.140

Supported Platforms:

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI 3-9

Adit 3104, Adit 3200, Adit 3500, MSR

Privileged Mode

debug portmon raw

Use the debug portmon raw command allows the user to display raw data related traffic. See no
debug portmon command on page 3-16.

Syntax: # debug portmon raw {off|on}

Example: adit 3500# debug portmon raw off

Field Definition

off Disable display of packet hex data

on Enables display of packet hex data

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

3-10 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

Privileged Mode

debug portmon serial

Use the debug portmon serial command allows the user to monitor traffic on a serial interface.

Note: Immediately after this command is issued, any traffic that falls into the filter parameter will

be displayed. To turn the monitoring off, you must issue a no debug portmon command. See no
debug portmon command on page 3-16.

Syntax: # debug portmon serial port {all|arp address|bootp

address|control|data|dns address|icmp address|ip address
|link|mgcp address|rip address|sip address|stp|tcp {address|
address:port|port}|udp {address|address:port|port}}

Field Definition

port Displays specific port traffic.

Adit 3104: Value must be 1.
Adit 3500: Range = 1-4.
MSR: Range = 1-8.

all Allows all traffic.

arp Displays all Address Resolution Protocol traffic.

address = IP address of the interface.

bootp Displays BootP related traffic.

address = IP address of the interface.

control Displays control related traffic.

data Displays data related traffic.

dns Displays Domain Naming Service related traffic.

address = IP address of the interface.

icmp Displays Internet Control Message Protocol related traffic.

address = IP address of the interface.

ip Displays Internet Protocol related traffic Note: Requires an IP address.

address = IP address of the interface.

link Displays link related traffic.

mgcp Displays Media Gateway Control Protocol related traffic.

address = IP address of the interface.

rip Displays Routing Information Protocol related traffic.

address = IP address of the interface.

sip Displays Session Initiation Protocol related traffic.

address = IP address of the interface.

stp Displays Spanning Tree Protocol related traffic.

tcp Displays Transmission Control Protocol related traffic.

address = IP address of the interface.
address:port = IP address
port = Port of the interface

Example: adit 3500# debug portmon 1 rip

Supported Platforms:

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI 3-11

Adit 3104, Adit 3200, Adit 3500, MSR

Privileged Mode

debug trace

Use the debug trace command allows the user to configure trace settings.
Note: Immediately after this command is issued, any trace that falls into the filter parameter will be

displayed. To turn the monitoring off, you must issue a no debug trace command. See no debug
trace command on page 3-16.

Syntax: # debug trace {cas|pri|sip} {enable|tx|rx}

Example: adit 3500# debug trace cas enable

Field Definition

cas Enable Channel Associated Signaling (CAS) tracing.

Note: Not supported on the Adit 3104.

pri Enable Primary Rate Interface (PRI) tracing.

Note: Not supported on the Adit 3104.

sip Enable Session Initiation Protocol (SIP) tracing.

enable Enable the trace.

tx Enable trace in the transmit direction.

rx Enable trace in the receive direction.

end

exit

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

Use the end command to exit the current configuration mode, and must be used to mark the end of any
configuration file. Note: This command can be entered in any Configuration mode with the same result.

Syntax: # end

Example: adit 3500# end

Username:

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

Use the exit command to close your current connection if you are in the User mode, or Privileged mode.
If the command is entered in a subconfiguration mode (Interface or Routing ), this command takes you
to the next higher level (example: back to Privileged mode from Interface configuration mode).

Syntax: # exit

Example: adit 3500# exit

adit 3500>

Supported Platforms:

3-12 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

Adit 3104, Adit 3200, Adit 3500, MSR

Privileged Mode

help

Use the help command to display the help information for this command. Note: This can also be
accomplished with a ?. This command can be entered in any configuration mode.

Syntax: # help

or

Syntax: # ?

Example: adit 3500# help

? Display all commands

clear Clear command

configure Switch to Configure mode

copy Configures device database

date Display time/date

debug Debug the system

end Exit to User mode

exit Exit to User mode

help Display all commands

history Display past entered commands

log Configure logging settings

no Disable a feature

ping Ping a remote host

reload Reboot the system

show Show various system information

traceroute Traceroute to a remote host

upgrade Upgrade firmware from a local computer

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI 3-13

Privileged Mode

history

Use the history command to display commands that have been entered in this session. This command
can be entered in any configuration mode.

Syntax: # history

Example: adit 3500# history

debug trace sip rx

no debug trace

no debug trace rx

no debug trace sip

no debug trace

no debug trace sip

debug trace

date

end

enable

configure terminal

history

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

3-14 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

Privileged Mode

log clear

Use the log clear command to clear the history of the log.

Syntax: # log clear {all|firewall|pri|sip|system|t1|lcc}

Field Definition

all Clear the entire event log.

firewall Clear firewall event log.

pri Clear PRI event log.

Note: Not supported on the Adit 3104.

sip Clear SIP event log.

system Clear system event log.

t1 Clear T1 event log.

(Adit 3104, Adit 3200, Adit 3500 only.)

lcc Clear Link Cross-Connect (LCC) event log.

(MSR only.)

Example: adit 3500# log clear firewall

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI 3-15

Privileged Mode

no debug

no debug portmon

Use the no debug portmon command to stop the Packet Monitor (portmon) process. To configure
a debug command, see the debug command on page 3-5.

Syntax: # no debug portmon

Example: adit 3500# no debug portmon

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

no debug trace

Use the no debug trace command to stop the trace process. To configure a debug trace, see the
debug trace command on page 3-12.

Syntax: # no debug trace {cas|pri|sip}

Field Definition

cas Remove trace CAS functions.

Note: Not supported on the Adit 3104.

pri Remove trace PRI functions.

Note: Not supported on the Adit 3104.

sip Remove trace SIP functions.

Example: adit 3500# no debug trace sip

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

3-16 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

Privileged Mode

ping

Use the ping command to send a sequence of ICMP echo request packets to the specified host. If the
host variable is omitted, and you are in Privileged mode, the router prompts you for additional
information. Note: The ping command verifies a connection and is a very important troubleshooting
tool.

Syntax: # ping {address [-i time] [-l size] [-n count]

[-w timeout]|stop}

Field Definition

address IP address of the host to ping.

-i time Specifies the intervals between pings.
Range is 0 - 600000 milliseconds.

-l size Specifies the size of the ping requests packets to be sent.
Range 64 - 1518.

-n count Specifies the number of ping requests to be sent.
Range 1-1000. Default is 4.

-w timeout Specifies the time to wait for a response before sending the next ping
request packet. Timeout is given in seconds. Range 1-600000. Default
is 2 seconds.

stop Stop the ping process.

Example: Adit 3500#

packet #1 has arrived

packet #2 has arrived

packet #3 has arrived

packet #4 has arrived

4 packets transmitted, 4 packets received

round-trip min/avg/max = 1/3/9 ms

Example: Adit 3500# ping 192.168.1.1 -n 2 -l 500

packet #1 has arrived

packet #2 has arrived

2 packets transmitted, 2 packets received

round-trip min/avg/max = 2/2/2 ms

Supported Platforms:

ping 192.168.1.1

Adit 3104, Adit 3200, Adit 3500, MSR

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI 3-17

Privileged Mode

reload

Use the reload command to reset the system.

CAUTION! THIS IS A SERVICE AFFECTING COMMAND.

Syntax: # reload

Example: adit 3500# reload

Going to reboot!
Restarting system.

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

3-18 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

Privileged Mode

show

For maneuverability through these commands, all command names in blue or italics are hyperlinked.

show alarms show dhcp-leases

show arp show digit-map

show caclkcd show interface description

show config access-control show interface ethernet

show config access-list show interface multilink

show config controller t1 show interface serial

show config dmz-host show ip ospf

show config host-filter show ip ospf database

show config interface ethernet show ip ospf interface

show config interface multilink show ip ospf neighbor

show config interface serial show ipsec

show config ip dhcp ethernet show l2tpc

show config local-server show licenses

show config nat-bypass show log

show config network-object show mac-address-table

show config port-trigger show nat-fw

show config remote-admin show port-trigger

show config security-default show pptpc

show config security-log show pptps

show config service show route

show config static-dns show running-config

show config time-range show service

show config voice-port fxs show users

show config voice-port trunk show version

show controller lcc show voice-port fxs

show controller t1 show voice-port trunk

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI 3-19

Privileged Mode

show alarms

Use the show alarms command to display the active alarms.

Syntax: # show alarms [t1 port|lcc number]

{alert|all|critical|info|major|minor}

Field Definition

t1 port Display alarms for a specific port.

Adit 3104: Value must be 1.
Adit 3500: Range = 1-4.

lcc number Display alarms for a specific Link Cross-Connect (LCC).

MSR: Range = 1-8.

alert Filter alert alarms (threshold crossing).

all Display all alarms.

critical Filter critical alarms.

info Filter information alarms.

major Filter major alarms.

minor Filter minor alarms.

Example: adit 3500# show alarms major

Alarm Severity Time

Alarm LOS T1 4 Major Jan 1 00:00:08 2006

Alarm LOS T1 3 Major Jan 1 00:00:08 2006

Alarm PRI T1 2 - Line NOT Ready Major Jan 1 00:00:07 2006

Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR

3-20 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

Privileged Mode

show arp

Use the show arp command to display the ARP (Address Resolution Protocol) table.

Syntax: # show arp {all|address|ethernet port}

Field Definition

all Display entire ARP table.

address Display ARP items of the entered IP address.

ethernet port Display Ethernet ARP items only.

port - Define an Ethernet port number. Range 1 - 2.

Example: adit 3500# show arp ethernet 1

1 192.168.1.1 ether Dynam 00:50:da:59:f0:25 eth_lan

Example: adit 3500# show arp 192.168.1.1

ip=192.168.1.1 flags=Dynam mac=00:50:da:59:f0:25 iface=eth_lan

Example: adit 3500# show arp all

# IP-address HW-type Flags HW-address Iface

1 192.168.1.1 ether Dynam 00:50:da:59:f0:25 eth-1

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI 3-21

Privileged Mode

show caclkcd

Use the show caclkcd command to display the linux kernel crash dump

Syntax: # show caclkcd

Example: adit 3500# show caclkcd

---------------- Begin cacLKCD -----------
Jan 1 2003 00:00:44 <3> openrg: unhandled page fault at pc=0x400528c0, lr=0x400
digit-map Show digit-map settings
52890 (bad address=0x30303038, code 245)Show various interfaces
pc : [<400528c0>] lr : [<40052890>] No Show l
r7 : 4006bb9c r6 : 30303038 r5 : 4006bb9c r4 : 4006bc1c
port-trigger
r3 : 30303030 r2 : 4006bc1c r1 : 4006bba5 r0 : 00000000
route Show routing table
Flags: nzCv IRQs on FIQs on Mode USER_32 Segment user Map the configurations to

CLI commands
User-mode stack:(0xbffffbac to 0xc0000000)
service Display services
fba0: 00000001 0036d238 003704d0 0036d238 003704d0their privilages
versio
fbc0: 003704d4 0002e1e0 00000001 003704d0 0002e1a8 00000004 00000005 000281d4
voice-port Show voice-port
fbe0: 4006d24d 4006d24c 4006d24c ffffffff 00000000 00rt Show
fce0: 00024324 00469c08 00000001 00025144 00469c08 00469c08 0009575c 40050458ip address
Ala

rm LOS T1#2
fd00: 002c85a0 000001e3 40e88bc0 00000000 00000000 00000000 0009574c 0036c448
exit
fd60: 0036e270 00000000 00000000 00000004 00000094 bffffdbc 00000004 40033490
fd80: 00000000 00000000 00000000 00000094 0011121c 0000008c bffffdbc 00263674
fda0: 00000bfd 0000008c 0011138c ffffffff ffffffff 00000007 00111c44 feedbabe
fdc0: 00001063 00033bb6 0000004e 00000000 00000023 002c81e8 4006b010 400335dc
fde0: 00000000 00000000 00000000 002c8188 401a430c 002c8188 00000023 002c81e8
fe00: 001df753 00000000 401a4494 4003f960 001df753 001df730 002c8188 001df753
fe20: 001df730 4006b010 401a5ae4 00000023 001df730 00000000 00000000 00000000
fe40: 00000000 00000000 0000009c 00000000 065ca5ac 00000002 0000009c 00000000
fe60: 057aacc3 00000000 00000000 40047924 00000020 401bb254 40032cf0 4002ead4
fe80: 00000020 400054d0 0000009c 00000000 05a4faa0 00000002 400051a8 0000c222
fea0: 00000000 40000ca4 00000000 00000000 00000000 400051a8 0000938c 00000000
fec0: 00000039 00282fac 0000bc4c 4000c848 00000000 40000ca4 bfffff34 bfffff3c
fee0: 00000001 00000704 bfffff3c 00000001 bfffff30 00000000 00000000 4006b010
ff00: 00000000 40051048 bfffff34 401bb458 0001f828 401967e4 00000000 00000000
ff20: 0001145c 00000000 40196814 00000000 00011474 bfffffd2 00000000 bfffffde
ff40: bfffffe5 00000000 00000010 00000097 00000006 00001000 00000011 00000064
ff60: 00000003 00008034 00000004 00000020 00000005 00000006 00000007 40000000
ff80: 00000008 00000000 00000009 0001145c 0000000b 00000000 0000000c 00000000
ffa0: 0000000d 00000000 0000000e 00000000 0000000f bfffffce 00000000 00000000
ffc0: 00000000 00000000 00000000 00007635 62002f62 696e2f6f 70656e72 6700484f
ffe0: 4d453d2f 00544552 4d3d6c69 6e757800 2f62696e 2f6f7065 6e726700 00000000

---------------- End cacLKCD -----------

Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR

3-22 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

Privileged Mode

show config access-control

Use the show config access-control command to display all access control filters.

Syntax: # show config access-control

Example: adit 3500# show config access-control

access-control id 1 apply-to lan time-range always service 1 enable

Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR

show config access-list

Use the show config access-list command to display all access lists.

Syntax: # show config access-list

Example: adit 3500# show config access-list

access-list rule 0 apply eth-lan direction in operation accept time-range 0
src-host 0.0.0.0-255.255.255.255 dst-host 0.0.0.0-255.255.255.255 service
50331673 frag none log none (enable)

Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI 3-23

Privileged Mode

show config controller t1

Use the show config controller t1 command to display the T1 information.

Syntax: # show config controller t1 port

Example: adit 3500# show config controller t1 1

controller t1 1

description T1 1

lbo short 133

fdl none

framing esf

linecode b8zs

loopdetect none

loopback none

idle-pattern 0x7f

no pri-group

no tdm-group

ds0-group timeslots 1-24

threshold daily ses 0

threshold daily sefs 0

threshold daily uas 0

threshold daily css 0

threshold daily les 0

threshold daily bes 0

threshold daily dm 0

threshold daily lcv 0

threshold daily pcv 0

threshold daily es 0

threshold min15 ses 0

threshold min15 sefs 0

threshold min15 uas 0

threshold min15 css 0

threshold min15 les 0

threshold min15 bes 0

threshold min15 dm 0

threshold min15 lcv 0

threshold min15 pcv 0

threshold min15 es 0

no shutdown

Field Definition

port T1 port to display.

Adit 3104: Value must be 1.
Adit 3500: Range 1 - 4.

Supported Platforms: Adit 3104, Adit 3200, Adit 3500

3-24 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

Privileged Mode

show config dmz-host

Use the show config dmz-host command to display the DMZ information.

Syntax: # show config dmz-host

Example: adit 3500# show config dmz-host

dmz-host 192.168.1.200 enable

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

show config host-filter

Use the show config host-filter command to display the IP and host name filters.

Syntax: # show config host-filter

Example: adit 3500# show config host-filter

host-filter id test ip-address 192.168.1.110 apply-to lan
time-range always

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI 3-25

Privileged Mode

show config interface ethernet

Use the show config interface ethernet command to display the Ethernet port information.

Syntax: # show config interface ethernet port

Example: adit 3500# show config interface ethernet 1

Field Definition

port Ethernet port to display. Range 1 - 2

Interface Ethernet 1

ip address 192.168.1.1 mask 255.255.255.0

description Ethernet 1

no tos ip

tos ip value 0x0

no ip dhcp auto-provision

no ip primary-dns

no ip secondary-dns

ip route-mode route

no ip default-route

no ip proxy-arp

no ip rip

ip rip receive-version 1or2

ip rip send-version 2-bcast

no firewall

metric 50

no shutdown

speed auto

full-duplex

remote-admin enable

no schedule-availability

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

3-26 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

Privileged Mode

show config interface multilink

Use the show config interface multilink command to display the Multilink port information.

Syntax: # show config interface multilink port

Field Definition

port Multilink port to display.

Adit 3104, Adit 3200, Adit 3500: Value must be 1.
MSR: Range = 1-8.

Example: adit 3500# show config interface multilink 1

Interface Multilink 1

ip address unnumbered

description Multilink 1

ip mtu auto

no ip primary-dns

no ip secondary-dns

ip route-mode napt

ip default-route enable

no ip rip

ip rip receive-version none

ip rip send-version none

no sip-alg

firewall enable

metric 0

no shutdown

no ppp authentication

no ppp encryption

no ppp username

ppp restart-timer 3

ppp time-btwn-reconnect 30

no ppp on-demand

ppp link-fragmentation 1600

no ppp qos-interleaving

no schedule-availability

Supported Platforms:

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI 3-27

Adit 3104, Adit 3200, Adit 3500, MSR

Privileged Mode

show config interface serial

Use the show config interface serial command to display serial interface information.

Syntax: # show config interface serial port

Example: adit 3500# show config interface serial 1

Field Definition

port Serial interface to display.

Adit 3104: Value must be 1.
Adit 3500: Range = 1-4.
MSR: Range = 1-8.

interface serial 1

encapsulation ppp

no ppp authentication

no ppp encryption

no ppp username

ppp restart-timer 3

ppp time-btwn-reconnect 30

no ppp on-demand

ip address unnumbered

description Serial 1

ip mtu auto

no ip primary-dns

no ip secondary-dns

ip route-mode napt

ip default-route enable

no ip rip

ip rip receive-version none

ip rip send-version none

no sip-alg

firewall enable

metric 0

no shutdown

no schedule-availability

Supported Platforms:

3-28 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

Adit 3104, Adit 3200, Adit 3500, MSR

Privileged Mode

show config ip dhcp ethernet

Use the show config ip dhcp ethernet command to display the DHCP Pool.

Syntax: # show config ip dhcp ethernet port

Field Definition

port Ethernet port to display. Range 1 - 2

Example: adit 3500# show config ip dhcp ethernet 1

ip dhcp pool ethernet 1

no relay

start-address 192.168.1.1

end-address 192.168.1.244

subnet-mask 255.255.255.0

lease 60

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

show config local-server

Use the show config local-server command to display the local server configuration.

Syntax: # show config local-server

Example: adit 3500# show config local-server

local-server id 0 hostname LocalHost1 time-range 0 fwd-port 160
service 16777216 enable

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI 3-29

Privileged Mode

show config nat-bypass

Use the show config nat-bypass command to display the NAT Bypass entries.

Syntax: # show config nat-bypass

Example: adit 3500# show config nat-bypass

nat-bypass ip-address 192.168.1.120 mask 255.255.255.0

nat-bypass ip-address 192.168.1.120 mask 255.255.255.0 enable

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

show config network-object

Use the show config network-object command to display the network object configuration.

Syntax: # show config network-object

Example: adit 3500# show config network-object

network-object id 0 description NetworkObject1 ip-address

192.168.1.200

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

show config port-trigger

Use the show config port-trigger command to display the port trigger information.

Syntax: # show config port-trigger

Example: adit 3500# show config port-trigger

port-trigger service 134217730 enable

port-trigger service 16777223 enable

Supported Platforms:

3-30 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

Adit 3104, Adit 3200, Adit 3500, MSR

Privileged Mode

show config remote-admin

Use the show config remote-admin command to display the remote admin configuration.

Syntax: # show config remote-admin

Example: adit 3500# show config remote-admin

remote-admin telnet primary-port port 23

remote-admin telnet secondary-port port 8023

remote-admin telnet primary-secure-port port 992

remote-admin web primary-port port 80

remote-admin web secondary-port port 8080

remote-admin web primary-secure-port port 443

remote-admin web secondary-secure-port port 8443

no remote-admin snmp

no remote-admin icmp

no remote-admin udp

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

show config security-default

Use the show config security-default command to display the security settings.

Syntax: # show config security-default

Example: adit 3500# show config security-default

security-default typical

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

show config security-log

Use the show config security-log command to display the security log.

Syntax: # show config security-log

Example: adit 3500# show config security-log

security-log accept-in-connects enable

security-log rem-admin-attempts enable

security-log prevent-log-overrun enable

Supported Platforms:

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI 3-31

Adit 3104, Adit 3200, Adit 3500, MSR

Privileged Mode

show config service

Use the show config service command display the current defined services.

Syntax: # show config service

Example: adit 3500# show config service

service id 4 name service1 description test

protocol tcp server-src-port 1-1 server-dst-port 4-4

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

show config static-dns

Use the show config static-dns command to display the static DNS entries.

Syntax: # show config static-dns

Example: adit 3500# show config static-dns

static-dns hostname test1 ip-address 10.10.2.2

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

show config time-range

Use the show config time-range command to display the time range configuration.

Syntax: # show config time-range

Example: adit 3500# show config time-range

time-range id 0 name Schedule1 inactive time-segment 0 sun time-range

00:00-00:30

Supported Platforms:

3-32 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

Adit 3104, Adit 3200, Adit 3500, MSR

Privileged Mode

show config voice-port fxs

Use the show config voice-port fxs command to display the FXS port information.

Syntax: # show config voice-port fxs [port]

Field Definition

port FXS port to display.

Adit 3104: Range = 1 - 24.
Adit 3500: Range = 1 - 4.
MSR: Range = 1 - 48.

Example: adit 3500# show config voice-port fxs 1

voice-port fxs
no digit-map
dial-timeout 5

voice-port fxs 1
description Line 1
no comfort-noise
echo-cancel enable
input-gain 0
output-gain 0
signal loop-start
no per-line-logging
no shutdown

Supported Platforms:

Adit 3104, Adit 3500, MSR

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI 3-33

Privileged Mode

show config voice-port trunk

Use the show config voice-port trunk command display the Trunk port information.

Syntax: # show config voice-port trunk port

Example: adit 3500# show config voice-port trunk 1

Field Definition

port Trunk port to display. Value must be 1.

Voice-port Trunk 1
description Trunk 1
trunk 000000005
no comfort-noise
connection t1 2
no echo-cancel
input-gain 0
output-gain 0
isdn switch-type pri-ni2
no digit-map
no registration enable

Example: adit MSR# show config voice-port trunk 1

Voice-port Trunk 1
description Trunk 1
trunk 000000005
no comfort-noise
echo-cancel enable
input-gain 0
output-gain 0
isdn switch-type pri-ni2
no digit-map
no registration enable

Supported Platforms:

Adit 3500, MSR

3-34 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

Privileged Mode

show controller lcc

Use the show controller lcc command to display the settings for a Link Cross Connect on the MSR
card.

Syntax: # show controller lcc number

Field Definition

number Link Cross Connect number, 1-8.

Example: Adit MSR> show controller lcc 1

Settings for interface LCC 1

---------------------------

Name : LinkCC 1
Device Name : LinkCC 1
Status : Operational
Network : WAN
Connection Type : Link Cross Connect
Connection : Data
Alarm Reporting : Enabled

Supported Platforms: MSR

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI 3-35

Privileged Mode

show controller t1

Use the show controller t1 command displays the T1 configuration and performance information.

Syntax: # show controller t1 port

Example: adit 3500# show controller t1 1

Settings for interface T1 1

---------------------------

Interface name : T1 1

Transmit status : Up

Receive status : Up

Framing : ESF

Clock source : Clock Reference 1

Line Code : B8ZS

Loop Detection : OFF

FDL Type : NONE

Line Length : DSX-1 equalization for 0-133ft

Status : Connected

Field Definition

port DS1 (T1) interface.

Adit 3104 Range = 1
Adit 3500 Range 1 - 4

Performance Threshold Settings 15 min 1 day

------ -----

unavailable seconds (uas): 0 0

severely errored seconds (ses): 0 0

errored seconds (es): 0 0

severely errored frame seconds (sefs): 0 0

line errored seconds (les): 0 0

controlled slip seconds (css): 0 0

bursty errored seconds (bes): 0 0

degraded minutes (dm): 0 0

line code violations (lcv): 0 0

path code violations (pcv): 0 0

Supported Platforms: Adit 3104, Adit 3200, Adit 3500

3-36 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

Privileged Mode

show dhcp-leases

Use the show dhcp-leases command to display the DHCP lease table.

Syntax: # show dhcp-leases

Example: Adit 3500# show dhcp-leases

Ethernet 1

Hostname : new-host IP:192.168.1.10 MAC:00:00:ff:ff:00:00
Type:static Expires-In:0

Supported Platforms:

Adit 3104, Adit 3200, Adit 3500, MSR

show digit-map

Use the show digit-map command to display the Digit Map patterns.

Syntax: # show digit-map

Example: adit 3500# show digit-map

Index Pattern

---------------------------------------------------------------

1 [2-9]11

2 [0-1][2-9]11

3 0[#T]

4 00

5 *xx

6 011x.[#T]

7 [0-1]xxxxxxx[#T]

8 [0-1][2-9]xxxxxxxxx

9 [2-9]xxxxxxxxx

10 [2-9]xxxxxx[#T]

Supported Platforms:

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI 3-37

Adit 3104, Adit 3500, MSR

Privileged Mode

show interface description

Use the show interface description command to display the interface information.

Syntax: # show interface description

Example: adit 3500# show interface description

Device State IP/Mask Dependencies

T1 1 running None

T1 2 running None

T1 3 up None

T1 4 up None

Serial 1 up 0.0.0.0/255.255.255.255 T1 1

Ethernet 2 disabled 0.0.0.0/0.0.0.0 None

Ethernet 1 running 192.168.1.1/255.255.255.0 None

IPsec 0 disabled 0.0.0.0/0.0.0.0 Serial 1

IPsec 1 running 192.168.1.1/255.255.255.0 Ethernet 1

Example: Adit MSR# show interface description

Device State IP/Mask Dependencies

LinkCC 1 running None

LinkCC 2 down None

LinkCC 3 down None

LinkCC 4 down None

LinkCC 5 down None

LinkCC 6 down None

LinkCC 7 down None

LinkCC 8 down None

Serial 1 up 0.0.0.0/255.255.255.255 LinkCC 1

Ethernet 2 up 194.168.1.1/255.255.0.0 None

Ethernet 1 running 192.168.1.1/255.255.255.0 None

IPsec 0 disabled 0.0.0.0/0.0.0.0 Serial 1

IPsec 1 running 192.168.1.1/255.255.255.0 Ethernet 1

Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR

3-38 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

Privileged Mode

show interface ethernet

Use the show interface ethernet command to display the Ethernet interface information.

Syntax: # show interface ethernet port

Field Definition

port Port number range 1-2.

Example: adit 3500# show interface ethernet 1

Device=Ethernet 1 State=running IP/Mask=192.168.1.1/255.255.255.0

Dependency=None

Status: Connected; Link: 10T-HD

Tx (Packets/Bytes/Dropped/Errors)=(1910/1451643/0/0)

Rx (Packets/Bytes/Dropped/Errors)=(2239/136636/0/0)

Broadcasts (Tx/Rx)=(0/0) Multicasts=0 Collisions=0

Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR

show interface multilink

Use the show interface multilink command to display the configuration of the Multilink.

Syntax: # show interface multilink port

Field Definition

port Multilink port number.

Adit 3104, Adit 3200, Adit 3500: Value must be 1.
MSR: Range is 1-8.

Example: adit 3500# show interface multilink 1

Device=mlink-1 State=down IP/Mask=Unnumbered

Dependency=t1-1,t1-4

Status: Disconnected

Example: adit MSR# show interface multilink 1

Device=mlink-1 State=down IP/Mask=Unnumbered

Dependency=LCC1,LCC3

Status: Disconnected

Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI 3-39

Privileged Mode

show interface serial

Use the show interface serial command to display the configuration of the serial interface.

Syntax: # show interface serial port

Example: adit 3500# show interface serial 1

Device=Serial 1 State=up IP/Mask=0.0.0.0/255.255.255.255

Dependency=T1 1

Status: Reconnecting...

Tx (Packets/Bytes/Dropped/Errors)=(556/6672/0/0)

Rx (Packets/Bytes/Dropped/Errors)=(0/0/0/0)

Field Definition

port Serial interface.

Adit 3104: Value must be 1.
Adit 3500: Range = 1-4.
MSR: Range = 1-8.

Example: adit MSR# show interface serial 3

Device=Serial 1 State=up IP/Mask=0.0.0.0/255.255.255.255

Dependency=LCC1

Status: Reconnecting...

Tx (Packets/Bytes/Dropped/Errors)=(3332/39984/0/0)

Rx (Packets/Bytes/Dropped/Errors)=(0/0/0/0)

Supported Platforms: Adit 3104, Adit 3500, MSR

3-40 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

Privileged Mode

show ip ospf

Use the show ip ospf command to display the general OSPF routing process information.

Syntax: # show ip ospf

Example: adit 3500# show ip ospf

Routing Process "ospf 0" with ID 192.168.1.1

Process uptime is 28 minutes

Process bound to VRF default

Conforms to RFC2328, and RFC1583Compatibility flag is disabled

Supports only single TOS(TOS0) routes

Supports opaque LSA

Supports Graceful Restart

SPF schedule delay 5 secs, Hold time between two SPFs 10 secs

Refreshtimer 10 secs

Number of incomming current DD exchange neighbors 0/5

Number of outgoing current DD exchange neighbors 0/5

Number of external LSA 0. Checksum 0x000000

Number of opaque AS LSA 0. Checksum 0x000000

Number of router LSA 0

Router LSA database is unlimited.

Number of network LSA 0

Network LSA database is unlimited.

Number of non-default summary LSA 0

Summary LSA database is unlimited.

Number of asbr summary LSA 0

ASBR Summary LSA database is unlimited.

Number of non-default external LSA 0

External LSA database is unlimited.

Number of LSA originated 0

Number of LSA received 0

Number of areas attached to this router: 0

Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR

Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI 3-41

Privileged Mode

show ip ospf database

Use the show ip ospf database command to display information related to the OSPF database for
a specific router. The various forms of this command deliver information on defined OSPF link
state advertisements.

Syntax: # show ip ospf database {setting}

Syntax: # show ip ospf database {adv-router address|self-originate}

Syntax: # show ip ospf database network link-state-id

Syntax: # show ip ospf database router {link-state-id|adv-router

Syntax: # show ip ospf database summary [link-state-id] [adv-router

address|self-originate}

address|self-originate]

Field Definition

adv-router address Displays all the LSAs of the specified router. If no IP address is

entered, the local router information will be displayed (same as self­originate).

link-state-id Portion of the Internet environment that is being described by the

advertisement. The value entered depends on the advertisement's LS
type. It must be entered in the form of an IP address. When the link
state advertisement is describing a network, the link-state-id can take
one of two forms:

1. The network's IP address (as in type 3 summary link advertisements
and in autonomous system external link advertisements).

2. A derived address obtained from the link state ID. (Note that
masking a network links advertisement's link state ID with the
network's subnet mask yields the network's IP address.)
When the link state advertisement is describing a router, the link state
ID is always the described router's OSPF router ID.
When an autonomous system external advertisement (LS Type = 5) is
describing a default route, its link state ID is set to Default Destination
(0.0.0.0).

network Displays information only about the network LSAs.

router Displays information only about the Router LSAs.

self-originate Displays only self-originated LSAs (from the local router).

summary Displays information on.ly about the summary LSAs.

3-42 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI