Carrier TSTTCCPB101, TSTATCCPB101 User Manual
TSTATCCPB101 PROGRAMMABLE
Carrier
Heating & Cooling
AUTO
72
DIGITAL THERMOSTAT
USER INFORMATION MANUAL FOR THE OPERATION AND
MAINTENANCE OF YOUR NEW THERMOSTAT
PROGRAMMABLE DIGITAL
THERMOSTAT
Dual Setpoint
COOL
Single Day Programmable
74
HEAT
72
4 Time periods
Very Easy to Program
Easy To Read Display
Thermoglow Backlight
No Batteries Required
Heat Pump & Heat Cool
Auto Changeover
Locking Keypad
Meets California Title 24 Residential
NOTE TO INSTALLER: THIS MANUAL MUST BE LEFT WITH THE EQUIPMENT USER.
Table Of Contents
FRONT PANEL
DISPLAY
QUICK START Set the clock and go
BASIC OPERATION
PROGRAMMING 4 Time Periods
ADVANCED SETUP
ABOUT ADVANCED OPERATION
WARRANTY
CAUTION
Follow Installation Instructions before proceeding.
2
3
4
5
7
10
14
17
SET THERMOSTAT TO MODE “OFF” PRIOR TO
CHANGING SETTINGS IN SETUP OR RESTORING
FACTORY DEFAULTS.
Residential Light Commercial Systems Carrier Corporation 04/01
TSTATCCPB101
Page 1
Front Panel
1
3
4
1
Liquid Crystal Display
AUTO
72
COOL
74
HEAT
2
72
5
with Thermoglow
2
Up/Down Buttons
3
4
5
Mode Button
Fan Button
Heat or Cool Indicator
Heat = Red, Cool = Green
Page 2
Display
1
AUTO
COOL
1
3
88
2
HEAT
1
88
3
1
1
Mode Indicators
Selects the operation mode of the equipment.
HEAT - indicates the heat mode.
COOL - indicates the air conditioning mode.
AUTO - indicates the system will automatically
changeover between heat and cool modes
as the temperature varies.
OFF
Fan On
4
88
AUTO - auto blinks to indicate the stored
program is enabled to run. When program
mode is entered the letters (pr) blink for two
seconds on the screen.
OFF - indicates the entire system is turned off.
Page 6.
2
Room Temperature Display
Indicates the current room temperature.
3
Desired Set Temperature
Indicates desired room temperature(s). Page 7.
4
Fan Operation Indication
Fan On - indicates constant, continuous fan
operation.
When Fan On is not lit - indicates the fan will
only operate when necessary to heat or
to cool. Page 7.
Page 3
Quick Start Set the Clock and Go
MODE
FAN
Hours
Press the Mode button.
While holding the Mode,
press the Fan button
for 2 seconds to enter Setup
screens.
i2
a
00
Minutes
am/pm
During Setup & Programming:
Pressing the Mode button
selects different flashing items.
(Represented in dark black)
Pressing the Up and Down
buttons will modify the flashing
selection.
To adjust the
Press
MODE
clock use
buttons.
Press both Mode and
Fan buttons as
above to return to
normal operation.
MODE
FAN
The thermostat is preprogrammed from the
factory to operate 1 or 2 Stage equipment* without
the need for further programming. To optimize the
installation of this thermostat follow the instructions
in the Advanced Setup section.
* The thermostat is not preprogrammed from the
factory to operate electric heat or heat pump systems.
To control these systems, follow the steps in the
Advanced Setup section, pages 12 & 13.
Page 4
Basic Operation
Select Mode
The HEAT setting indicates the
temperature the room has to
reach before the furnace will
turn on to heat the room.
The COOL setting indicates the
temperature the room has to
reach before the air conditioner
will turn on to cool the room.
72
72
HEAT
74
COOL
72
MODE
MODE
AUTO will automatically select
heat or cool based on room
temperature demand.
AUTO - auto blinks to indicate the
stored program is enabled to run.
When program mode is entered
the letters (pr) blink for two
seconds on the screen.
OFF indicates both heating
and air conditioning
systems are turned off.
AUTO
72
AUTO
72
72
OFF
COOL
74
HEAT
72
MODE
COOL
74
HEAT
72
MODE
Page 5
Loading...