Installation Instructions
TSTATCCPF701
TSTATBBPF701
P374-1100FM
NOTE: Read the entire instruciton manual before starting the installation.
Digital Thermostat
Am
I2:00
M
72
74
COOL
AUTO
HEAT
70
HEAT
COOL
&
HEAT
PUMP
MULTI-STAGE SEVEN DAY PROGRAMMABLE
Form: IM-TSTAT-08
Cancels: Printed in U.S.A.
Catalog No. 13TS-TA34
Table Of Contents
PREPARATION
REMOVE OLD THERMOSTAT
WIRE CONNECTIONS
WIRING DIAGRAMS
CALIBRATION
TEST OPERATION
TROUBLESHOOTING
CAUTION
Replacement Components Division Carrier Corporation 4/01
This device complies with Part 15 of the FCC rules.
Operation is subject to the following 2 conditions:
(1) This device may not cause harmful interference,
and (2) This device must accept any interference
received, including interference that may cause
undesired operation.
Follow Installation Instructions carefully.
DISCONNECT POWER TO THE HEATER AIR CONDITIONER BEFORE REMOVING
THE OLD THERMOSTAT AND INSTALLING
THE NEW THERMOSTAT.
WARNING
2
3
4
5
8
9
10
Page 1
STEP #1
PREPARATION
Proper installation of the thermostat will be
accomplished by following these step
by step instructions. If you are unsure
about any of these steps, call a qualified
technician for assistance.
Assemble tools & recommended
Junction Box or Wall Bracket.
FLATSTAT
‘Mud rings’ or Remodel boxes will
not fit.
EXTENDS
LESS THAN
3/8” FROM
THE WALL.
Flat Blade
Screwdriver
Wire cutter
& Stripper
Make sure your Heater/Air Conditioner
is working properly before beginning
installation of the thermostat.
Carefully unpack the thermostat.
Save the screws, wall anchors, and
instructions.
Turn off the power to the Heating/Air
Conditioning system at the main fuse
panel. Most residential systems have
a separate breaker for disconnecting
power to the furnace.
.366”
WALL
FlatStat
in Standard
J-Box or
supplied
Wall
Bracket
WALL
Page 2
STEP #2
REMOVE & REPLACE OLD THERMOSTAT
Remove the cover of the old thermostat.
If it does not come off easily check for
screws.
Loosen the screws holding the thermostat
base or subbase to the wall, and lift away.
Disconnect the wires from the old
thermostat. Tape the ends of the wires
as you disconnect them, and mark them
with the letter of the terminal for easy
reconnection to the new thermostat.
Keep the old thermostat for reference
purposes, until your new thermostat is
functioning properly.
Remove the white plastic wire connector from the
rear of the thermostat. Install wires as directed.
Press the wired connector on the back of the
thermostat.
Lift Connector straight up
to remove.
For best operation, install
the thermostat in a junction
box that is free from drafts
that originate inside the wall.
Page 3
STEP #3
WIRE CONNECTIONS
If the terminal designations on your old
thermostat do not match those on the
new thermostat, refer to the chart below,
or the wiring diagrams that follow.
Wire from the
old thermostat
terminal marked
G or F Fan G
Y1, Y or C
W1, W or H
C
O/B
Y2
W2
RS+5 RS+5
RS RS
RS G GND
CK1
CK2
Function
Cooling Y1
Heating
PowerRh, R, M, Vr, A R
Common
Rev. Valve
2nd Stage Cool
2nd Stage Heat
Remote Sensor +5vdc
Remote Sensor Signal
Remote Sensor Ground
Dry Contact Switch 1
Dry Contact Switch 2
Install on the
new thermostat
connector marked
W1,O,B
W1,O,B**
* C may not be used on all systems.
** O/B is used if your system is a Heat Pump.
Page 4
C *
Y2
W2
Sample Wiring Diagrams
5 Wire, 1 Stage Cooling, 1 Stage Gas Heat
O
R
W2
Y2
Y1
W1
C
G
Thermostat
* If using electric heat this option must be
selected on during advanced setup.
Residential Gas or Electric Heat *,
Electric Cool, split systems & package
units
24 vac common
fan relay
compressor relay
1st stage heat circuit
24 vac return
L
E
C
G
Y1
O
W1
R
Y2
W2
4 Wire, 1 Stage Cooling, 1 Stage Gas Heat
O
R
W2
Y2
W1
Y1
C
G
Thermostat
* If using electric heat this option must be
selected on during advanced setup.
Page 5
Residential Gas or Electric Heat *,
Electric Cool, split systems & package
units
fan relay
compressor relay
1st stage heat circuit
24 vac return
L
E
C
G
Y1
O
W1
R
Y2
W2
Sample Wiring Diagrams
6 Wire, 1 Stage Cooling, 2 Stage Heat
W2
O
R
W1
Y1
C
G
Y2
Residential & commercial 1 Stage Cooling,
with 2 Stage Gas or Electric Heat*
Thermostat
1st stage heat circuit
2nd stage heat circuit
5 Wire, 1 Stage Cooling, 1 Stage Heat - Heat Pump*
W2
O
R
W1
Y1
C
G
Y2
Thermostat
No auxiliary heat, residential Heat Pumps ,
split systems & package units
compressor relay
* If using residential heat pump, this option
must be selected on during advanced setup.
24 vac common
fan relay
compressor relay
24 vac return
24 vac common
fan relay
reversing valve
24 vac return
L
E
C
G
Y1
O
W1
R
Y2
W2
L
E
C
G
Y1
O
W1
R
Y2
W2
Page 6
Sample Wiring Diagrams
7 Wire, Fan Coil w/ 3 Speed Fan
O
R
W2
Y2
W1
Y1
C
G
Thermostat
Commercial Gas or Electric Heat ***,
Electric Cool, split systems & package units
including Commercial Heat Pumps **
24 vac common
fan relay - low speed
compressor relay
hot water valve
24 vac return
fan relay - med. speed
fan relay - high speed
L
E
C
LOW
Y1
O
W1
R
MED
HI
5 Wire, 1 Stage Cooling, 1 Stage Heat - Heat Pump*
W2
O
R
W1
Y1
C
G
Y2
Thermostat
No auxiliary heat, residential Heat Pumps ,
split systems & package units
compressor relay
* If using residential heat pump, this option
must be selected on during advanced setup.
Page 7
24 vac common
fan relay
reversing valve
24 vac return
L
E
C
G
Y1
O
W1
R
Y2
W2
Sample Wiring Diagram
6 Wire, 1 Stage Cooling, 2 Stage Heat, Heat Pump *
W2
O
R
W1
Y1
C
G
Y2
Most residential split and package heat pumps
with auxiliary heat
Thermostat
24 vac common
fan relay
compressor relay
1st stage heat circuit
24 vac return
2nd stage heat circuit
* The heat pump option must be selected
on during advanced setup.
Calibration
Every thermostat is calibrated before it leaves the factory.
Under normal circumstances there will never be a need to
recalibrate the thermostat again.
To accommodate special needs, the thermostat may be recalibrated
following these steps:
1. While holding the mode button in, press the down arrow button
for 5 seconds. After all the icons in the display appear, release
the buttons.
2. Press the mode button once.
3. Press the up or down buttons until the flashing number
equals the current room temperature.
4. Press the mode button to return to normal operation.
L
E
C
G
Y1
O
W1
R
Y2
W2
Page 8
STEP #4
TEST OPERATION
Turn the power on to the Heating/Air
Conditioning system.
Press the On/Off button repeatedly until
the HEAT icon appears on the display.
Press the Up or Down buttons until the set
temperature is 10 degrees above room
temperature. The furnace should turn on.
Press the On/Off button repeatedly until
the COOL icon appears on the display.
Press the Up or Down buttons until the set
temperature is 10 degrees below room
temperature. The air conditioner should
turn on. NOTE: Most equipment has a
time delay of 5 minutes between cool
cycles. This feature is defeatable on the
thermostat. Consult the Owner's Manual
under Setup, cycles per hour.
Page 9
TROUBLESHOOTING
SYMPTOM: When using 4 wires (R, G, W, Y),
the air conditioning equipment tries
repeatedly to turn on, but cannot. At
times the display dims or disappears.
CAUSE: There is not enough power available
to "power share".
REMEDY: Connect a 270 ohm, 10 watt power
resistor at the furnace as shown below.
For Problem A/C For Problem Heat
R G W Y C
R G W Y C
TR300-10w
TR300-10w
SYMPTOM: The air conditioning does not
attempt to turn on.
CAUSE: The compressor timer lockout may
prevent the air conditioner from
turning on, for a period of time.
REMEDY: Consult the Owner's Manual in
the Setup section to defeat the
cycles per hour and compressor
timeguard.
SYMPTOM: The display is blank.
CAUSE: Lack of proper power.
REMEDY: Make sure power is turned on to
the furnace and 24vac between R & W.
If C is used, 24vac between R & C.
Page 10
TROUBLESHOOTING
SYMPTOM: The air conditioning does not
attempt to turn on.
CAUSE: The cooling setpoint is set too
high.
REMEDY: Consult the Owner's Manual in
the Setup section to lower the
cooling setpoint limit.
SYMPTOM: The heating does not attempt
to turn on.
CAUSE: The heating setpoint is set too
low.
REMEDY: Consult the Owner's Manual in
the Setup section to raise the
heating setpoint limit.
Page 11
TROUBLESHOOTING
SYMPTOM: When controlling a residential heat
pump, and asking for cooling, the heat
comes on.
CAUSE: Heat pump is not selected "on" in the
Advanced Setup.
REMEDY: Select heat pump on during Advanced
Setup programming. Consult the Owner's
Manual.
SYMPTOM: When calling for cooling, both
the heat and cool come on.
CAUSE: The Advanced Setup is configured
to control a heat pump, and the hvac
the thermostat is controlling is a
"conventional" (non heat pump)
system.
REMEDY: Consult the Owner's Manual in
the Advanced Setup section to turn
off the heat pump.
4Z95
Page 12
FlatStat
F
FOR HOME OR OFFICE USE
TSTATCCPF701
TSTATBBPF701
P374-1100FM
Tested to Comply
c
with FCC Standards
C
P/N 88-113
Loading...