Page 1
KSACN0101CAC
KSACN0101AAA
Owner’s Manual
SAFETY CONSIDERATIONS
Installing, starting up, and servicing air- conditioning equipment
can be hazardous due to system pressures, electrical components,
and equipment location (roofs, elevated structures, etc.).
Only trained, qualified installers and service mechanics should
install, start- up, and service this equipment.
Untrained personnel can perform basic maintenance functions
such as cleaning coils. All other operations should be performed
by trained service personnel.
When working on the equipment, observe precautions in the
literature and on tags, stickers, and labels attached to the
equipment.
Follow all safety codes. Wear safety glasses and work gloves.
Keep a quenching cloth and fire extinguisher nearby when
brazing. Use care in handling, rigging, and setting bulky
equipment.
Read these instructions thoroughly and follow all warnings or
cautions included in literature and attached to the unit. Consult
local building codes and National Electrical Code (NEC) for
special requirements. Recognize safety information. This is the
!
!
safety- alert symbol
in instructions or manuals, be alert to the potential for personal
injury. Understand these signal words: DANGER, WARNING,
and CAUTION. These words are used with the safety- alert
symbol. DANGER identifies the most serious hazards which will
result in severe personal injury or death. WARNING signifies
hazards which could result in personal injury or death. CAUTION
is used to identify unsafe practices which may result in minor
personal injury or product and property damage. NOTE is used to
highlight suggestions which will result in enhanced installation,
reliability, or operation.
ELECTRICAL SHOCK HAZARD
Failure to follow this warning could result in personal injury or
death.
Before beginning any modification or installation of this kit, be
sure the main electrical disconnect is in the OFF position.
Ensure power is disconnected to the fan coil unit. On some
systems both the fan coil and the outdoor unit may be on the
same disconnect. Tag the disconnect switch with a suitable
warning label. There may be more than one disconnect.
EQUIPMENT DAMAGE HAZARD
Failure to follow this warning may result in equipment
damage.
Do not install wired controller in an area subjected to excessive
steam, oil or sulfide gas. Doing so may cause the controller to
deform and/or fail.
. When you see this symbol on the unit and
!
!
WARNING
CAUTION
Wired Remote Controller
Ductless Split Systems
Kit Contents: Confirm that all the following parts are included.
No. Description Qty Remarks
1 Wired Remote Controller 1 n/a
Installation and owner’s
2
manual
3 Screws 3
4 Wall plugs 3 For wall mounting
5 Screws 2
6 Plastic screw bars 2
7 Theconnectivewiresgroup 1 24AWG
Field Supplied Components: Prepare the following on site.
Description
Switch Box 1 n/a n/a
Wiring Tube
(insulating sleeve and
tightening screw)
S This manual contains installation procedures for the wire
controller only. Refer to the indoor unit Installation Manual for
connecting the Wire Controller and the Indoor Unit.
S Install the wire joint (5p) to the appointed position of the electric
controlling box.
S The wired controller circuit is a low voltage circuit. Never
connect it with a standard 220V/380V circuit or place it in the
same wiring tube as the circuit. The interval must be more than
11.8- 19.7in. (300~500mm).
S The shield cable must be connected stable to the ground or the
transmission may fail.
S Do not extend the shield cable by cutting. If necessary, use a
Terminal Connection Block to connect.
S After finishing the connection, do not use a Meggar to perform
the installation check to the signal wire.
Qty
1 n/a n/a
1 n/a
M4X20 (for mounting on the wall)
M4X25 (for mounting on the wall)
For fixing on the
switch box
Type Remarks
Page 2
CONTROLLER INDICATOR NAMES AND FUNCTIONS
1. OPERATION MODE INDICATION
Press the MODE button to select the following modes: AUTO,
COOL, DRY, HEAT, FAN ONLY, and AUTO. The HEAT mod e
does not exist on the cooling only model.
2.TIMER
Adjust the ON time or ONLY ON time setting and the ON
indicator displays. Adjust the OFF time or the ONLY OFF time
and the OFF indicator displays. If the ON and OFF timer are both
set, both the ON and OFF indicators display.
3. FOLLOW ME
After the temperature is set, the temperature sensor inside the wire
controller compares the two temperatures. The air temperature
around the wire controller determines the unit’s temperature
setting. This function is available in the COOLING, HEATING,
and AUTO modes.
4. ON/OFF INDICATOR
The icon displays when the indicator is on.
5. FAN SPEED INDICATOR
There are four fan modes: low, middle, high, and auto.
NOTE: Some models do not have the middle fan option.
6. LOCK
Press the “LOCK” button to disable the other buttons. Press again
to enable the other buttons.
7. TEMPERATURE DISPLAY ZONE
The zone displays the set temperature. Press the
buttons to adjust the setting. In the fan mode, the temperature
button does not appear.
YBtemperature
2
Page 3
INSTALLA TION METHOD
When a wired remote controller is needed, add a small 5- way terminal and secure an infrared emitter with gumwater near the receiver on
the switch board. Connect the anode and cathode A and B, and +5V, GND, RUN to , C, D, E to the switch board.
3
Page 4
WIRED CONTROLLER BUTTONS NAMES AND OPERATIONS
1. MODE BUTTON
Press this button to change the operation mode in the following
sequence: AUTO, COOL DRY, HEAT, FAN, and back to AUTO.
Remark: The COOLING ONLY model does not have a HEAT
mode.
2. TIMER ON BUTTON
Press this button to activate the TIMER ON function. With every
press, the time increases 0.5h. After 10h, the time increases in 1h
increments. To cancel, set to ”0.0”.
3. TIMER OFF BUTTON
Press this button to activate the TIMER OFF function. With every
press, the time increases 0.5h. After 10h, the time increases in 1h
increments. To cancel, set to ”0.0“.
4. FOLLOW ME BUTTON/I- FEEL BUTTON
When in the COOL, HEAT or AUTO mode, press this button to
activate the FOLLOW ME function. Press again to deactivate.
5. ELECTRICAL HEATER BUTTON/HEATER BUTTON
Press this button in the HEAT mode to deactivate the electrical
heater function.
6. RESET BUTTON (hidden)
Use a .039 inch (1mm) stick and place in the hole to cancel the
current setting. The wire controller should revert to its original
setting.
7. ON/OFF BUTTON
When the unit is off, press this button and the indicator displays,
the wire controller powers on and sends the setting information to
the indoor PCB. When on, press this button, the indicator turns
off and sends the instruction. If the TIMER ON or TIMER OFF
function has been set, it cancels the setting and sends instructions
to power off the unit.
8. ADJUST BUTTON
Press and hold the button and the temperature increases 2F (1C)
every 0.5 second.
9. ADJUST BUTTON
Press and hold the button and the temperature decreases 2F (1C)
every 0.5 second.
10. SWING BUTTON
Press the START SWING button to start the function and the
button again to stop.
11. ECONOMY OPERATION BUTTON / SLEEP BUTTON
Press this button to operate the indoor unit in the ECONOMY
mode. Press this button again to exit this mode (this button may
be ineffective for some models).
12. FAN SPEED BUTTON
Press this button consecutively and the fan speed will cycle in the
following direction: AUTO, LOW, MEDIUM, HIGH.
Y
B
4
Page 5
13. LOCK BUTTON (hidden)
Press the LOCK button and all the current settings are locked. The
wire controller will not accept any operation except the LOCK
button. Use LOCK when you want to prevent the setting from
being changed. Press the LOCK button again to cancel the LOCK
mode.
USING METHOD
AUTOMATIC OPERATION
Connect power to the unit and the indoor operation lamp flashes.
1. Press the MODE button and select AUTO.
2. Press
”Y” and ”B” , set the temperature you want, generally it
is around 62F (17C)~88F (30C).
3. Press the ON/OFF button and the operation lamp lights. The air
conditioner operates in the AUTO mode and the indoor fan mode
is AUTO and can not be changed. AUTO displays on the LCD.
Press the ON/OFF button again to stop.
4. The ECONOMY operation is valid in the AUTO mode.
COOL/HEAT/FAN MODE OPERATION
1. Press the MODE button, select COOL, HEAT or the FAN
ONLY mo d e.
2. Press the temperature adjust button to select the setting
temperature.
3. Press the FAN SPEED button to select the speeds:
HIGH/MID/LOW/AUTO.
4. Press the ON/OFF” button and the indoor unit operation lamp
lights and operates in the selected mode. Press the ON/OFF button
again and it stops. Remark: When in the FAN mode the
temperature can not be set.
TIMER SETTING
Timer on only
1. Press the TIME ON button and it displays SET on the LCD
along with H and ON to indicate it is waiting for the TIMER ON
setting.
2. Press the TIMER ON button repeatedly to adjust the time
setting.
3. Press this button and hold to increase the time by 0.5h. After
10h, the time increases by 1h.
4. After setting 0.5 second, the wire controller sends the TIMER
ON information and it is finished.
Timer off only
1. Press the TIME OFF button and it displays SET on the LCD
and H and ON to indicate it is waiting for the TIMER ON setting.
2. Press the TIME OFF button repeatedly to adjust the time setting.
3. Press this button and hold and the time increases by 0.5h. After
10h, the time increases by 1h.
4. After setting 0.5 second, the wire controller sends the TIMER
OFF information and it is finished.
TIMER OFF AND TIMER OFF BOTH
1. Set the TIMER ON time as detailed in the corresponding step 1
and 2.
2. Set the TIMER OFF time as described in the corresponding
step1 and 2.
3. The TIMER OFF time must be longer than the TIMER ON
time.
4. .05 seconds after setting, the wire controller sends the
information and the setting is finished.
DRY OPERATION
1. Press the MODE button and select the DRY mode.
2. Press the temperature adjust button to select the setting
temperature.
3. Press the ON/OFF button and the indoor unit operation lamp
lights and it works in the DRY mode. Press the ON/OFF button
again and it stops working.
4. In the DRY mode the ECONOMY o p eration and fan speed are
ineffective.
TECHNICAL INDICATION AND REQUIREMENT
EMC and EMI comply with the CE certification requirements.
CHANGE TIMER
If you need to change the timer’s time, press the corresponding
button to do so. To cancel the timer, change the time to 0.0.
NOTE: The timer’s time is relative and it delayed after the setting
time (for example, setting time is 8:05 A.M). So when the timer is
set, the standard time can be adjusted.
5
Page 6
Copyright 2015 CAC / BDP S 7310 W. Morris St. S Indianapolis, IN 46231
Manufacturer reserves the right to change, at any time, specifica tions and designs without notice and without o bligations .
Edition Date: 02 /15
6
Catalog No: OMKSACN0101 - 01
Replaces: NEW
Loading...