CARR 127444 Super Hoop Multi-Mount Step User Manual

Diagram A

Diagram

B

DIAGRAM A & B ARE VIEWED FROM THE DRIVERS SIDE

Super Hoop Multi-Mount Step Installation Instructions

Part No’s: 127441 / 127442 / 127444

SLIDE

Outside Pinch Weld

HEX SHEET METAL SCREW

WAX YOUR STEP ON A

Carr Pattern Co., Inc.

Super Hoop Multi-Mount Step Installation Instructions

Part No’s: 127441 / 127442 / 127444

 Do not over tighten the nuts and bolts or damage to the castings and or stripping of the threads could result.
 FOR SAFE AND PROPER USAGE OF THIS PRODUCT, THE MOUNTING INSTRUCTIONS MUST BE FOLLOWED CAREFULLY AND COMPLETELY.
 The manufacturer and distributor of this product are in no way responsible for the consumer’s failure to adhere to the warnings and directions of these instructions in the

event of damage to the consumer’s vehicle, other properties and or personal injury.

Quality and Style that Endures

Follow the diagram and the written

directions carefully for a proper, safe

installation.

Should you encounter an unusual,

Vehicle Application:

DODGE

‘11-'14 Ram 2500-5500 Reg. Cab
(Diesel only)

REGULAR BASIS TO

MAINTAIN ITS LUSTER

MATERIAL NEEDED:

Drill motor, 11/32” drill bit, 1/8” drill bit,
pencil, flat blade screw driver or 5/16"
socket, center punch, two ½” wrenches,
one 7/16” wrench, 5/32" Allen Wrench and
silicone.

MATERIAL FURNISHED:

Two step castings, four mounting brackets,
instruction page and two hardware packs.
(Not all hardware may be used)

unforeseen problem, contact our

Technical Help Line

WARNINGS!

7:00 AM – 3:00 PM Pacific Time

[phone]

Visit our web-site at

www.CARR.com

Carr Pattern Co., Inc.

1. These steps mount to an extremely strong part of your vehicle, the back side of its rocker

panels. For the proper position of the step, the front edge of the seat while in normal
driving position should be in line with the center of the step. For personal preference or to
avoid any obstruction that may be on the backside of the rocker panel, the step can be
moved towards the front or the rear of the vehicle.

2. Assemble two mounting brackets to a step as shown in Diagram A using the 1/4" hardware

provided and with your 5/32" Allen wrench and 7/16" wrench.

Finishes: Limited Lifetime
Structural Warranty: Limited Lifetime
Warranty Conditions:

a. All warranties start from consumer’s date of purchase.
b. A new product will be sent out immediately to replace

a warranty claim.

c. The above guidelines apply only to the Original

Purchaser.

d. Original proof of purchase must be submitted for all

warranty and returns issues.

Warranty Limitations:

a. Warranty coverage extends ONLY to repair or

replacement of the CARR product. This warranty does
not cover the cost of labor, transportation, installation
or removal of the product.

b. Warranty coverage does not extend to damage caused

by: collision, fire, theft, freezing, vandalism, riot,
explosion or object striking the product, or misuse of
the product and/or the vehicle on which the product is
being installed.

c. Warranty coverage does not extend to damage caused

by: airborne fallout (chemicals, tree sap, etc.), stones,
hail, earthquake, water or flood, windstorm, lightning,
the application of chemicals or sealants subsequent to
manufacture.

d. Warranty coverage does not extend to damages caused

by: normal wear and tear, abuse, modification or
improper installation of the product.

e. Warranty coverage does not extend to any economic

loss or extra expense including (without limitation),
payment for the loss of time or pay, inconvenience,
storage, loss of vehicle use, vehicle rental expense,
equipment rental expense, lodging, meals, or other
travel costs.

Other Terms:

This warranty gives you specific legal rights and you may
also have other rights that vary from state to state. CARR
does not authorize any person to create for it any other
obligation or liability in connection with its products.
ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE APPLICABLE TO THIS
PRODUCT IS LIMITED IN DURATION TO THE
DURATION OF THIS WRITTEN WARRANTY.
PERFORMANCE OF REPAIRS AND NEEDED
ADJUSTMENTS IS THE EXCULSIVE REMEDY
UNDER THIS WRITTEN WARRANTY OR ANY
IMPLIED WARRANTY. CARR SHALL NOT BE
LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES RESULTING FROM BREACH OF THIS
WRITTEN WARRANTY.*
*Some states do not allow limitations on how long an
implied warranty will last or the exclusion or limitation of
incidental or consequential damages, so that above
limitations or exclusions may not apply to you.
Guarantee: Every attempt has been made to manufacture
and distribute the finest quality products available. Our
manufactured products are guaranteed to be free of defects
due to workmanship or materials. Distributed products are
subject to manufacturer’s warranty only.

CARR ● 27447 Bostik Court ● Temecula CA

Warranty Policy

92590

3. Take that assembly and slide it in from the front of the vehicle between the Black

Emissions Tank and the Body Metal as shown in Diagram A.

4. Position the step assembly in the general location as shown in Diagram B. Note: If you

position the front bracket on the Optional Mounting Surface you will not need the Optional
Wedge Washer but your step will be positioned more forward. Check this location to be
sure it is correct for you.

5. Using the Mounting Brackets as a guide, take a pencil and mark the center of each

Mounting Bracket on the Outside Pinch Weld with a vertical line. See Diagram A.

6. Remove your step assembly.

7. Measure 3/8" up from the bottom of the pinch Weld and mark a horizontal line. This will

create a cross-air mark. The distance between the center of each cross-air mark needs to be
17 7/8". If not make the necessary adjustment to correct the dimension.

8. Take your Center Punch and punch the center of each cross-air mark.

9. Take your Drill Motor with a 1/8" drill bit and drill out marked holes.

10. Go back and drill out the 1/8" hole with a 11/32" drill bit. Remove all burrs.

11. Slide the step assembly back into position. With the 5/16" hardware provided, hand tighten

the step to the vehicle.

12. If you are using the Wedge Washer, position it now so that it takes up any slack between

the front Mounting Bracket and the Vehicle Body Metal. See Diagram B.

13. Take the drill motor again and drill out the hole at the top of the front Mounting Bracket.

Drill through the Wedge Washer and Vehicle Body Metal.

14. Take the 1" Hex Sheet Metal screw provided with your 5/16" socket wrench and securely

tighten the screw. NOTE: You will not be able to put a Hex Sheet Metal screw on the
back Mounting Bracket due to interference from the Black Emissions Tank.

15. Go back and securely tighten all the 5/16" hardware.

16. Repeat all of the above for the passenger side of your vehicle.

17. The passenger side will not have the Black Emissions Tank in your way so you will be

able to place the Step Assembly into position easier and you will be able to install the Hex
Sheet Metal screws for back Mounting Bracket.

18. Use silicone on all drilled areas to insure a better weather resistant installation.

19. Your steps are ready for use.