CARR 126334 Super Hoop Multi-Mount Step User Manual

Diagram A

Diagram

B

DIAGRAM

S A, B, C & D

ARE VIEWED FROM THE

PASSENGER

SIDE

Diagram

C

Diagr

a3 D

Super Hoop Multi-Mount Step Installation Instructions

Part No’s: 126331 / 126332 / 126334

WAX YOUR STEP O

N A

Carr Pattern Co., Inc.

Super Hoop Multi-Mount Step Installation Instructions

Part No’s: 126331 / 126332 / 126334

 Do not over tighten the nuts and bolts or damage to the castings and or stripping of the threads could result.
 FOR SAFE AND PROPER USAGE OF THIS PRODUCT, THE MOUNTING INSTRUCTIONS MUST BE FOLLOWED CAREFULLY AND COMPLETELY.
 The manufacturer and distributor of this product are in no way responsible for the consumer’s failure to adhere to the warnings and directions of these instructions in the

event of damage to the consumer’s vehicle, other properties and or personal injury.

Quality and Style that Endures

Follow the diagram and the written

directions carefully for a proper, safe

installation.

Should you encounter an unusual,

Vehicle Application:

CHEVY

‘11-'14 Sierra/Silverado 2500-
3500 All Cabs (Diesel)

REGULAR BASIS TO

MAINTAIN ITS LUSTER

MATERIAL NEEDED:

Drill motor, 11/32” drill bit, 1/8” drill bit,
pencil, flat blade screw driver or 5/16"
socket, center punch, one ½” wrenches,
one 7/16” wrench, 5/32" Allen Wrench,
Loctite and silicone.

MATERIAL FURNISHED:

Two step castings, four mounting brackets,
instruction page and two hardware packs.
(Not all hardware may be used)

unforeseen problem, contact our

WARNINGS!

Technical Help Line

7:00 AM – 3:00 PM Pacific Time

[phone]

Visit our web-site at

www.CARR.com

Carr Pattern Co., Inc.

1. These steps mount to an extremely strong part of your vehicle, the back side of its

rocker panels. For the proper position of the step, the front edge of the seat while in
normal driving position should be in line with the center of the step. For personal
preference or to avoid any obstruction that may be on the backside of the rocker panel,
the step can be moved towards the front or the rear of the vehicle.

2. Take the Mounting Brackets and slide them up along the grooves of the Black

Emissions Tank so that the Mourting Brackets are resting on the inside of the Pinch

Finishes: Limited Lifetime
Structural Warranty: Limited Lifetime
Warranty Conditions:

a. All warranties start from consumer’s date of purchase.
b. A new product will be sent out immediately to replace

a warranty claim.

c. The above guidelines apply only to the Original

Purchaser.

d. Original proof of purchase must be submitted for all

warranty and returns issues.

Warranty Limitations:

a. Warranty coverage extends ONLY to repair or

replacement of the CARR product. This warranty does
not cover the cost of labor, transportation, installation
or removal of the product.

b. Warranty coverage does not extend to damage caused

by: collision, fire, theft, freezing, vandalism, riot,
explosion or object striking the product, or misuse of
the product and/or the vehicle on which the product is
being installed.

c. Warranty coverage does not extend to damage caused

by: airborne fallout (chemicals, tree sap, etc.), stones,
hail, earthquake, water or flood, windstorm, lightning,
the application of chemicals or sealants subsequent to
manufacture.

d. Warranty coverage does not extend to damages caused

by: normal wear and tear, abuse, modification or
improper installation of the product.

e. Warranty coverage does not extend to any economic

loss or extra expense including (without limitation),
payment for the loss of time or pay, inconvenience,
storage, loss of vehicle use, vehicle rental expense,
equipment rental expense, lodging, meals, or other
travel costs.

Other Terms:

This warranty gives you specific legal rights and you may
also have other rights that vary from state to state. CARR
does not authorize any person to create for it any other
obligation or liability in connection with its products.
ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE APPLICABLE TO THIS
PRODUCT IS LIMITED IN DURATION TO THE
DURATION OF THIS WRITTEN WARRANTY.
PERFORMANCE OF REPAIRS AND NEEDED
ADJUSTMENTS IS THE EXCULSIVE REMEDY
UNDER THIS WRITTEN WARRANTY OR ANY
IMPLIED WARRANTY. CARR SHALL NOT BE
LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES RESULTING FROM BREACH OF THIS
WRITTEN WARRANTY.*
*Some states do not allow limitations on how long an
implied warranty will last or the exclusion or limitation of
incidental or consequential damages, so that above
limitations or exclusions may not apply to you.
Guarantee: Every attempt has been made to manufacture
and distribute the finest quality products available. Our
manufactured products are guaranteed to be free of defects
due to workmanship or materials. Distributed products are
subject to manufacturer’s warranty only.

CARR ● 27447 Bostik Court ● Temecula CA

Warranty Policy

92590

weld. See Diagram A.

3. Slide the back Mounting Bracket towards the front of the vehicle as shown in Diagram

B. IMPORTANT: There is a wire harness on the backside of the Body Metal.

Make sure each Mounting Bracket is flat against the Body Metal and not resting
on the wire harness. If the wire harness is between the Mounting Bracket and the
Body Metal, serious damage could occur to your vehicle's electrial system.

4. That the Step Casting witht the 1/4" hardware provided with your 5/32" Allen and

7/16" wrench and securely tighten the Step Casting to the Mounting Brackets.
Diagram C.

5. Position the step assembly in the desired position. Find the center of each Mounting

Bracket and mark two vertical lines on the painted surface of the body metal. Distance
between the two vertical lines need to be 17 7/8". See Diagram C.

6. Move the step assembly to the side for the next step and for drilling out the holes.

7. At each mark vertical line, measure up from the edge of the Pinch Weld 1/2" and mark

another line forming a cross-hair mark. Diagram C.

8. Center punch the center of each cross-hair mark. Drill out the centers with a 1/8" drill

bit and than go back and drill the holes with a 11/32" drill bit. Remove all burrs.
Reposition the step assembly so that the holes in the step and drilled holes line up.

9. Take the 5/16" hardware provided and hand tighten the Mounting Brackets to the

Body Metal. NOTE: We suggest using Loctite when installing these bolts.
IMPORTANT: The holes in the Mounting Brackets are threaded. Make sure you hand
tighten the 5/16 bolts several turns before final tightening. Failure to do this may strip
out the threaded holes. Filing holes larger may be necessary if they don't align. Dia. D.

10. The hex sheet metal screws provided are not necessary for the step where the

Black Emissions Tank is located. The other three steps will use the hex sheet metal
screw. To install the hex sheet metal screws, take a 1/8" drill bit and drill out the top
holes on each Mounting Bracket. Take the sheet metal screws and securely tighten.

11. For all the other Step Castings, follow the same steps above, leaving out all references

to the Black Emissions Tank.

12. Use silicone on all drilled areas to insure a better weather resistant installation.

13. Your steps are ready for use.