CARR 125004 No-Drill Super Hoop Step User Manual
No-Drill Super Hoop Step Mounting Instructions
Exploded View of Clip Installation
WAX YOUR STEP ON A
Body Metal
See the other side of th
i
s
installations
Carr Pattern Co., Inc.
CARR
● 27447 Bostik Court ● Temecula CA 92590
Part No’s: 125001, 125002 & 125004
Quality and Style that Endures
Follow the diagram and the written
directions carefully for a proper,
safe installation.
Should you encounter an unusual,
unforeseen problem, contact our
Technical Help Line
7:00 AM – 3:00 PM Pacific Time
(951) 719-1068
Visit our web-site at
www.CARR.com
Carr Pattern Co., Inc.
Vehicle Application:
FORD
‘99-‘14 Super Duty all cabs/all doors/all series
MATERIAL NEEDED:
Two 7/16” wrenches, two 1/2” wrenches.
MATERIAL FURNISHED:
Two step castings, four zinc plated steel brackets, one hardware pack and an
instruction sheet.
Clip
Do not over tighten the nuts and bolts or
damage to the castings and or stripping of the
threads could result.
FOR SAFE AND PROPER USAGE OF THIS
PRODUCT, THE MOUNTING
INSTRUCTIONS MUST BE FOLLOWED
CAREFULLY AND COMPLETELY.
The manufacturer and distributor of this product
are in no way responsible for the consumer’s
failure to adhere to the warnings and directions
of these instructions in the event of damage to
the consumer’s vehicle, other properties and or
personal injury.
REFER TO DIAGRAM “A” WIRE
HARNESS. STEP “8” ON THIS PAGE
MUST BE FOLLOWED, IF NOT
ELECTRICAL DAMAGE TO YOUR
VEHICLE MAY OCCUR.
Finishes: Limited Lifetime
Structural Warranty: Limited Lifetime
Warranty Conditions:
a. All warranties start from consumer’s date of purchase.
b. A new product will be sent out immediately to replace a warranty claim.
c. The above guidelines apply only to the Original Purchaser.
d. Original proof of purchase must be submitted for all warranty and returns issues.
Warranty Limitations:
a. Warranty coverage extends ONLY to repair or replacement of the CARR product. This warranty does not cover the cost of labor, transportation, installation or removal of the product.
b. Warranty coverage does not extend to damage caused by: collision, fire, theft, freezing, vandalism, riot, explosion or object striking the product, or misuse of the product and/or the vehicle on
which the product is being installed.
c. Warranty coverage does not extend to damage caused by: airborne fallout (chemicals, tree sap, etc.), stones, hail, earthquake, water or flood, windstorm, lightning, the application of chemicals or
sealants subsequent to manufacture.
d. Warranty coverage does not extend to damages caused by: normal wear and tear, abuse, modification or improper installation of the product.
e. Warranty coverage does not extend to any economic loss or extra expense including (without limitation), payment for the loss of time or pay, inconvenience, storage, loss of vehicle use, vehicle
rental expense, equipment rental expense, lodging, meals, or other travel costs.
Other Terms:
This warranty gives you specific legal rights and you may also have other rights that vary from state to state. CARR does not authorize any person to create for it any other obligation or liability in
connection with its products. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE APPLICABLE TO THIS PRODUCT IS LIMITED IN
DURATION TO THE DURATION OF THIS WRITTEN WARRANTY. PERFORMANCE OF REPAIRS AND NEEDED ADJUSTMENTS IS THE EXCULSIVE REMEDY UNDER THIS
WRITTEN WARRANTY OR ANY IMPLIED WARRANTY. CARR SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM BREACH OF
THIS WRITTEN WARRANTY.*
*Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages, so that above limitations or exclusions may not
apply to you.
Guarantee: Every attempt has been made to manufacture and distribute the finest quality products available. Our manufactured products are guaranteed to be free of defects due to workmanship or
materials. Distributed products are subject to manufacturer’s warranty only.
WARNINGS!
Instruction for vehicles
Warranty Policy
REGULAR BASIS TO
MAINTAIN ITS LUSTER
DIAGRAM FOR:
Super Hoop Multi-Mount Step Installation Instructions
DIAGRAM FOR:
DIAGRAM FOR:
Clip
Clip
Truck Brace
Truck Brace
Part No’s:125001, 125002 & 125004
Front door ALL CABS.
Clip
Body Metal
Front of the vehicle
1. Place the steel brackets on the step casting the
same way as shown on the diagram.
2. Securely tighten the steel brackets to the step
casting with the ¼” hardware provided.
3. Install the clips as shown here by pushing the clips
to the side. (A larger view of the clips installation is
available on the reverse side of this sheet).
4. Take the 5/16” hardware that is provided and bolt the
step and bracket assembly to the truck under the
front door using the holes in the truck as indicated on
the diagram.
5. Repeat the same procedure for the passenger side
of your vehicle.
Drivers side shown here
Rear door EXTENDED CAB.
Body Metal
Front of the vehicle
Front of the vehicle
Body Metal
1. Place the steel brackets on the step casting the
same way as shown on the diagram.
2. Securely tighten the steel brackets to the step
casting with the ¼” hardware provided.
3. Install the clips as shown here by pushing the clips to
the side. (A larger view of the clips installation is
available on the reverse side of this sheet).
4. Take the 5/16” hardware that is provided and bolt the
step and bracket assembly to the truck under the
rear door using the holes in the truck as indicated on
the diagram.
5. Repeat the same procedure for the passenger side
of your vehicle only reverse how the steel brackets
bolt to the step casting.
1. Place the steel brackets on the step casting the
same way as shown on the diagram.
2. Securely tighten the steel brackets to the step
casting with the ¼” hardware provided.
3. Install the clips as shown here by pushing the clips
to the side.. (A larger view of the clips installation is
available on the reverse side of this sheet).
4. Take the 5/16” hardware that is provided and bolt
the step and bracket assembly to the truck under
the rear door using the holes in the truck as
indicated on the diagram.
5. Repeat the same procedure for the passenger side
of your vehicle only reverse how the steel brackets
bolt to the step casting.
Drivers side shown here
Rear door CREW CAB.
Drivers side shown here
Loading...