CARR 110742 Tread Plate User Manual

Part No.’

s 110701

-

110702 / 110711

-

110712 / 110941

-

110942

Carr Pattern Co., Inc.

3” DIA. TREAD PLATE INSTALLATION INSTRUCTIONS

WARNINGS!

WARNINGS!

WARNINGS!WARNINGS!

 FOR SAFE AND PROPER USAGE OF THIS PRODUCT, THE MOUNTING INSTRUCTIONS MUST BE FOLLOWED

CAREFULLY AND COMPLETELY.

 The manufacturer and distributor of this product are in no way responsible for the consumer’s failure to adhere to the warnings

and directions of these instructions in the event of damage to the consumer’s vehicle, other properties and or personal injury.

1. Position each Tread Plate on your side bar or tube bumper in the desired position for
easy entry and exit.

2. When the desired position is obtained, mark the holes on your bar or bumper using
the holes in the Tread Plate as guides.

3. Center punch each marked hole.

4. Using a 3/16” drill bit, drill out the holes.

5. Place the Thread Plate back on the bar or bumper and using the hardware provided,
screw the Tread Plates to your bar or bumper and securely tightened.

6. Now you step is ready for use.

Finishes: Limited Lifetime

Warranty Policy
Structural Warranty: Limited Lifetime
Warranty Conditions:

a. All warranties start from consumer’s date of purchase.
b. A new product will be sent out immediately to replace a warranty claim.
c. The above guidelines apply only to the Original Purchaser.
d. Original proof of purchase must be submitted for all warranty and returns issues.

Warranty Limitations:

a. Warranty coverage extends ONLY to repair or replacement of the CARR product. This warranty

does not cover the cost of labor, transportation, installation or removal of the product.

b. Warranty coverage does not extend to damage caused by: collision, fire, theft, freezing,

vandalism, riot, explosion or object striking the product, or misuse of the product and/or the
vehicle on which the product is being installed.

c. Warranty coverage does not extend to damage caused by: airborne fallout (chemicals, tree sap,

etc.), stones, hail, earthquake, water or flood, windstorm, lightning, the application of chemicals
or sealants subsequent to manufacture.

d. Warranty coverage does not extend to damages caused by: normal wear and tear, abuse,

modification or improper installation of the product.

e. Warranty coverage does not extend to any economic loss or extra expense including (without

limitation), payment for the loss of time or pay, inconvenience, storage, loss of vehicle use,
vehicle rental expense, equipment rental expense, lodging, meals, or other travel costs.

Other Terms:

This warranty gives you specific legal rights and you may also have other rights that vary from
state to state. CARR does not authorize any person to create for it any other obligation or liability
in connection with its products. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE APPLICABLE TO THIS PRODUCT IS LIMITED
IN DURATION TO THE DURATION OF THIS WRITTEN WARRANTY. PERFORMANCE
OF REPAIRS AND NEEDED ADJUSTMENTS IS THE EXCULSIVE REMEDY UNDER THIS
WRITTEN WARRANTY OR ANY IMPLIED WARRANTY. CARR SHALL NOT BE LIABLE
FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM BREACH OF
THIS WRITTEN WARRANTY.*
*Some states do not allow limitations on how long an implied warranty will last or the exclusion or
limitation of incidental or consequential damages, so that above limitations or exclusions may not
apply to you.
Guarantee: Every attempt has been made to manufacture and distribute the finest quality products
available. Our manufactured products are guaranteed to be free of defects due to workmanship or
materials. Distributed products are subject to manufacturer’s warranty only.

CARR ● 27447 Bostik Court ● Temecula CA 92590

Quality and Style that Endures

Should you encounter an unusual,

unforeseen problem, contact our

Technical Help Line

7:00 AM – 3:00 PM Pacific Time

[phone]

Visit our web-site at

www.CARR.com

Carr Pattern Co., Inc.

Materials Furnished:
1 – Aluminum Tread Plate casting
2 – Sheet metal screws
1 – Instruction sheet

Tools Needed:

• Center punch

• Drill Motor

• 3/16” drill bit