CARR 104504 Hoop II Multi-Mount Step User Manual
Ho
op II Multi
-
Mount Step Installation Instructions
tightening.
Carr Pattern Co., Inc.
Part No’s: 104501, 104502 & 104504
Do not over tighten the nuts and bolts or damage to the castings
and or stripping of the threads could result.
FOR SAFE AND PROPER USAGE OF THIS PRODUCT, THE
MOUNTING INSTRUCTIONS MUST BE FOLLOWED
CAREFULLY AND COMPLETELY.
The manufacturer and distributor of this product are in no way
responsible for the consumer’s failure to adhere to the warnings
and directions of these instructions in the event of damage to the
consumer’s vehicle, other properties and or personal injury.
WARNINGS!
Materials Furnished:
Two step castings, four steel mounting brackets,
instruction sheet and two hardware packs (Important!
Not all of the parts in these hardware packs may be
needed for proper installation).
Tools Needed:
One - Phillips screwdriver, two – 1/2” open or box
wrenches, pencil, center punch, drill motor, sharp 1/8”
drill bit, sharp 5/16” drill bit,
1. These steps mount to an extremely strong part of your vehicle, the
back side of its rocker panels. For the proper position of the step,
the front edge of the seat while in normal driving position should be
in line with the center of the step. For personal preference or to
avoid any obstruction that may be on the backside of the rocker
panel, the step can be moved towards the front or the rear of the
vehicle.
2. Assemble the steel mounting brackets to the step as shown in the
drawing, but only hand tighten.
3. When positioning the assembled step against the back side of the
rocker panel, be sure to avoid all bumps and screws to ensure that
the step is against a flat surface. Take a pencil and mark a vertical
line that lines up with the front edge of the seat, on the outside
painted surface of the pinch weld. (See diagram). Disassemble the
brackets from the step.
4. Measure 4 1/8” on each side of the marked vertical line and mark
two more lines on that same surface. The dimension between the
two outside marked lines should be 8 1/4”.
5. Measure 3/8” from the edge of the pinch weld where you marked
the other vertical lines and mark two horizontal lines, creating a
cross hair. NOTE: DOUBLE CHECK DIMENSIONS BEFORE
DRILLING! (Warning: when drilling holes leave at least 1/8” of
metal between the hole and the edge of the pinch weld).
6. Take a center punch and punch the center where the two sets of
lines cross.
7. Take a 1/8” drill bit and drill out the centered punched holes.
8. Enlarge the 1/8” hole with a 5/16” drill bit.
9. After drilling make sure that all the burrs are removed.
10. Now you will need to bend the tab on the back of each bracket as
shown on the diagram to conform to the body metal of your vehicle.
11. Once the tabs are bent to the correct angle, use the 5/16” x 5/8” hex
bolts with the 5/16” hex nuts and 5/16” washers to securely tighten
the brackets on the vehicle.
12. Using the top ¼” hole at the top of each steel mounting bracket,
take a 1/8” drill bit and drill holes into the body metal. Take the
5/8” sheet metal screws provided and securely tighten. (Drilling at
an angle may be necessary due to interference or for proper
alignment). Place the step back into the brackets and securely
tighten.
13. We advise putting silicone sealer around the areas where the steel
mounting brackets contact the body metal.
14. After one month of use, go back and give all hardware a final
Quality and Style that Endures
Follow the diagram and the
written directions carefully for a
proper, safe installation.
Should you encounter an
unusual, unforeseen problem,
contact our Technical Help Line
7:00 AM – 3:00 PM Pacific Time
(951) 719-1068
Visit our web-site at
www.CARR.com
Finishes: Limited Lifetime
Structural Warranty: Limited Lifetime
Warranty Conditions:
a. All warranties start from consumer’s date of purchase.
b. A new product will be sent out immediately to replace a warranty
claim.
c. The above guidelines apply only to the Original Purchaser.
d. Original proof of purchase must be submitted for all warranty and
returns issues.
Warranty Limitations:
a. Warranty coverage extends ONLY to repair or replacement of the
CARR product. This warranty does not cover the cost of labor,
transportation, installation or removal of the product.
b. Warranty coverage does not extend to damage caused by: collision,
fire, theft, freezing, vandalism, riot, explosion or object striking the
product, or misuse of the product and/or the vehicle on which the
product is being installed.
c. Warranty coverage does not extend to damage caused by: airborne
fallout (chemicals, tree sap, etc.), stones, hail, earthquake, water or
flood, windstorm, lightning, the application of chemicals or sealants
subsequent to manufacture.
d. Warranty coverage does not extend to damages caused by: normal
wear and tear, abuse, modification or improper installation of the
product.
e. Warranty coverage does not extend to any economic loss or extra
expense including (without limitation), payment for the loss of time
or pay, inconvenience, storage, loss of vehicle use, vehicle rental
expense, equipment rental expense, lodging, meals, or other travel
costs.
Other Terms:
This warranty gives you specific legal rights and you may also have
other rights that vary from state to state. CARR does not authorize any
person to create for it any other obligation or liability in connection
with its products. ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE APPLICABLE TO THIS PRODUCT IS LIMITED IN
DURATION TO THE DURATION OF THIS WRITTEN
WARRANTY. PERFORMANCE OF REPAIRS AND NEEDED
ADJUSTMENTS IS THE EXCULSIVE REMEDY UNDER THIS
WRITTEN WARRANTY OR ANY IMPLIED WARRANTY. CARR
SHALL NOT BE LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES RESULTING FROM BREACH OF
THIS WRITTEN WARRANTY.*
*Some states do not allow limitations on how long an implied warranty
will last or the exclusion or limitation of incidental or consequential
damages, so that above limitations or exclusions may not apply to you.
Guarantee: Every attempt has been made to manufacture and
distribute the finest quality products available. Our manufactured
products are guaranteed to be free of defects due to workmanship or
materials. Distributed products are subject to manufacturer’s warranty
only.
CARR ● 27447 Bostik Court ● Temecula CA 92590
Warranty Policy
This st
ep fits the following vehicles:
pinch weld
pinch weld
Hoop II Multi
-
Mount Step Installation I
nstructions
Part No’s: 104501, 104502 & 104504
WAX YOUR STEP ON A REGULAR BASIS TO MAINTAIN ITS LUSTER
TOYOTA JEEP
‘05-’14 Tacoma all cabs all doors/Prerunner/4Runner ’02-’14 KJ Liberty (CAUTION: Ground
’00-’14 Toyota Tundra clearance problem on stock vehicle)
’01-’07 Toyota Sequoia 08-10 Commander
’07-’14 FJ Cruiser
DODGE – Sprinter Van - 02-06
Diagrams below show passenger side of vehicle
Front door step view Rear door step view
Pinch Weld
Bend Tab
Bend Tab
Main Bolts
Mark vertical
center line on the
outside painted
surface of the
Main Bolts
Mark vertical
center line on the
outside painted
surface of the
Loading...