Page 1
®
NEW WORK CEILING FAN
AND LIGHT FIXTURE BAR HANGER
INSTRUCTION SHEET
Individual Cat. No
FN-CFB-HB...............
READ ALL INSTRUCTIONS AND WARNINGS CAREFULLY BEFORE PROCEEDING!
New Work Bar Hanger with NON METALLIC CEILING FAN BOX
WARNING
DISCONNECT THE ELECTRICAL CIRCUIT SUPPLYING POWER
TO THE OUTLET PRIOR TO INSTALLATION.
CAUTION
TO PREVENT INJURY, THE HANGER MUST BE SECURELY
INSTALLED IN ACCORDANCE WITH THESE INSTRUCTIONS
BEFORE MOUNTING OR CONNECTING A CEILING FAN OR
LIGHT FIXTURE.
AFTER INSTALLATION OF THE HANGER, BE SURE TO
FOLLOW ALL MOUNTING INSTRUCTIONS WITH INCLUDED WITH
CEILING FAN OR LIGHT FIXTURES.
—CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY QUESTIONS. —
IMPORTANT SAFETY NOTICE:
INSTALLATION INSTRUCTIONS:
1. Expand the bar hanger to the length of spacing between the wood
ceiling joists. The locating tabs on end-plates are used to position
the hanger.
USE ONLY NON-METALLIC BOX AND SCREWS PROVIDED IN KIT. DO NOT SUBSTITUTE!
D
O NOT EXCEED MAXIMUM WEIGHT RATINGS
FOR 16” SPANS
MAX LIGHT FIXTURE = 50 LBS.
MAX CEILING FAN = 35 LBS.
FOR 24” SPANS
MAX LIGHT FIXTURE = 50 LBS.
MAX CEILING FAN = 35 LBS.
INSTALL THIS BAR HANGER SUPPORT ONLY IN
ACCORDANCE WITH APPLICABLE NATIONAL AND LOCAL
BUILDING AND ELECTRICAL CODES.
CAUTION
Figure 1
TA04770 A Page 1 of 2
END-PLATE
LOCATING
TAB
Page 2
#12-14 X 1" LONG SCREW (4)
OVERLAP
BOX SUPPORT
BRACKET
FAN MOUNTING
SCREWS
SPURS (4)
Figure 2
INSTALLATION INSTRUCTIONS - continued
WARNING
DO NOT USE THE SPURS AS SOLE MEANS OF SUPPORT FOR THE HANGER.
2. Use a hammer to strike the engaging spurs into the wood ceiling joist. This will provide temporary support for
the hanger.
3. Using the holes in the end plates of the hanger as a template, drill (4) 7/64˝ diameter pilot holes 3/8˝ deep
(MAX.). Use the wood screws provided and install securely through holes of the end plates. (See Figure 2).
4. Align and fasten the box support bracket along the hanger where the outlet box is to be mounted on the hanger.
WARNING
THE BOX SUPPORT BRACKET MUST BE POSITIONED WITHIN THE OVERLAP
OF THE TWO CHANNELS (SEE FIGURE 2).
5. Attach the ceiling fan box by aligning the two holes on side of the bottom center with the two holes in the box
support bracket.
• Drive the provided #8-32 x 3/4" fan mounting screws with lockwashers into each of the two holes through
the box fastener (See Figure 2).
WARNING
FAN MOUNTING SCREWS FURNISHED BY THOMAS & BETTS MUST BE USED WITH LOCKWASHERS
FOR CARLON NON-METALLIC CEILING FAN BOXES. DO NOT SUBSTITUTE SCREWS.
WARRANTY: Thomas & Betts sells this product with the understanding that the user will perform all necessary tests to determine the suitability of this product for the user's intended application.
®
Limitations and Exclusions: THE ABOVE WARRANTY IS THE SOLE WARRANTY CONCERNING THIS PRODUCT, AND IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, WHICH ARE SPECIFICALLY DISCLAIMED. LIABILITY
FOR BREACH OF THE ABOVE WARRANTY IS LIMITED TO COST OF REPAIR OR REPLACEMENT OF THE PRODUCT, AND UNDER NO CIRCUMSTANCES WILL THOMAS & BETTS BE
LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Thomas & Betts Corporation
Memphis, Tennessee
© 2014 Thomas & Betts. All Rights Reserved.
www.tnb.com
TA04770
A Page 2 of 2
Loading...