Carlo Gavazzi RGC2P, RGC3P Catalog Page
Solid State Relays
3-Phase with Integrated Heatsink
Proportional Switching Controllers
Types RGC2P, RGC3P
• 2-pole and 3-pole analog switching solid state
contactors
• Rated operational voltage: up to 600VAC
• Rated operational current: up to 75AAC
• Control inputs: 0-20mA, 4-20mA, 12-20mA, 0-5V, 1-5V, 0-10V
• Local setting through external potentiometer
• Switching modes: phase angle or distributed full
cycles (1, 4 or 16 full cycles)
• Soft start feature with selectable ramp time up to 5 seconds
• Integrated varistor protection on output
• Monitoring for SSR and load malfunction
• EMR alarm output for alarm indication
• 100kA short circuit current rating according to UL508
• DIN or panel mount
• RoHS compliant
Product Description
This series gives the possibility to
control output power of 3-phase
loads with an analog control
input. The RGC2P is a 2-phase
switching product whilst the
RGC3P switches all 3 phases.
Input types cover a wide range of
current and voltage ranges. Local
setting by an external
potentiometer is also possible.
Switching modes cover phase
angle control, distributed full
cycle control and soft start for
limiting inrush current of loads
having a high temperature
coefficient, such as short wave
infrared heaters.
Detection of mains loss, load
loss, SSR short circuit and overtemperature is integrated in
some models. Alarm condition is
signalled through an EMR output
and is visually indicated by the
alarm LED. Additional LEDs
indicate input and load status.
Specifications are at a
surrounding temperature of 25°C
unless otherwise specified.
Ordering Key
Solid state relay
Number of switched poles
Type of switching
Rated operational voltage
Control input
Rated operational current
Switching mode
External supply
Integrated fan
Monitoring features
Ordering Key (Refer to page 4 for valid part numbers)
SSR with
heatsink
RGC2:
2-pole
switching +
1-pole direct
RGC3:
3-pole
switching
FC = Full Cycle
OTP = Over Temperature Protection
EMR = Electromechanical Relay
1. Input types I and V require an external supply Us
2. Refer to Derating Curves
Type of
switching
P: Proportional 60:
Rated voltage
(Ue), Blocking
voltage
180 - 660VAC,
1200Vp
Control
1
input
AA:
4-20mADC
I:
0-20mADC
4-20mADC
12-20mADC
V:
0-5VDC
1-5VDC
0-10VDC
Rated
current/ pole
@
40°C
20: 20AAC
25: 25AAC
30: 30AAC
40: 40AAC
65: 65AAC
75: 75AAC
RGC 3 P 60 V 65 C1 D F M
Switching
2
mode
E: Phase Angle
C1: 1 FC ON,
1FC OFF @
50% input
C4: 4 FC ON,
4FC OFF @
50% input
C16: 16 FC ON,
16FC OFF @
50% input
S: Soft Start
S16: Soft Start +
mode C16
External
supply (Us)
D: 24VAC/DC
A: 90 - 250VAC
Features
P: Integrated
over
temperature
protection
(OTP), mains
loss with EMR
alarm output
F: Integrated fan
M: Monitoring
for Mains loss,
Load loss, SSR
short circuit,
open circuit and
OTP with EMR
alarm output
Specifications are subject to change without notice (18.02.2014) 1
RGC2P, RGC3P
General Specifications
RGC..AA.. RGC..I.. RGC..V..
Latching voltage (across each pole L-T) 20V
Operational frequency range 45 to 65Hz
Power factor > 0.7 @ rated voltage
Output Power 0 to 100%
Touch Protection IP20
CE marking Yes
Pollution degree 2 (non-conductive pollution with possibilities of condensation)
Over-voltage category III (fixed installations)
LED status indication
Control ON Green Green Green
Supply ON n/a Green Green
Load ON n/a Yellow Yellow
Alarm ON Green, flashing
Isolation
Input & Output to Case 4000Vrms 4000Vrms 4000Vrms
Input to Output 2500Vrms 2500Vrms 2500Vrms
External supply to input
Us to A1, A2, A3, A4, A5, Uf, 11, 12, 14, C1, C2 n/a 1500Vrms 1500Vrms
External supply & input to EMR
Us, A1, A2, A3, A4, A5, Uf, C1, C2 to 11, 12, 14 n/a 1500Vrms 1500Vrms
<4mA, flashing 0.5s ON, 0.5s OFF Full intensity Full intensity
>4mA, intensity varies with input
Flashing 0.5s ON, 0.5sOFF Flashing 0.5s ON, 0.5sOFF
N according to load status ON accordingto load status
3
O
Red, flashing
3
Red, flashing
3
3: Refer to LED Indications
Output Voltage Specifications
Operational voltage range
Line to line voltage, L1/L2/L3 180-660 VAC
Permissible voltage unbalance 10% between L1/L2/L3
Blocking voltage 1200Vp
Leakage current @ rated voltage 5mAAC per pole
Internal Varistors
(across each pole) Yes
Specifications are subject to change without notice (18.02.2014) 5
Loading...