Carlo Gavazzi RGC Data sheet

Solid State Relays
1-Phase with Integrated Heatsink
Zero Cross or Instant On Switching

Types RGC Solid State Contactor ‘E’ Connection

• Product width ranging from 17.5mm up to 70mm

• Rated operational voltage: up to 660 VAC

• Rated operational current: up to 85 AAC @ 40°C

• 18000 A

• Control voltages: 3-32 VDC, 20-275 VAC (24-190 VDC)

• Design according to EN/IEC60947-4-2, EN/IEC60947-4-3,
EN/IEC62314, UL508, CSA 22-2 No. 14-13

• Integrated voltage transient protection with varistor

• 100 kA short circuit current rating according to UL508

2

s for the I2t and 1200 Vp blocking voltage

1 2

Product Description

This new range of solid state
contactors presents a unique
opportunity to maximize effi­ciency in panel space and
is an evolution of solid state
switches for which Carlo
Gavazzi is very well known.

The nominal current ratings
are at 40˚C. The smallest

1. RGC..32 models are not VDE approved

2. Germanischer Lloyd approval applicable only to models RGC1....15.KE,

RGC1...20.KE, RGC1..25..KE and RGC1....30.KE

width is 17.5mm and is rated
at 37 AAC. Power and control
teminals allow for safe loop­ing of cables.

Voltage transient protection
is standard across the output
with a varistor. Specifications
are stated at 25°C unless
otherwise noted.

Ordering Key

RGC 1 A 60 A 30 K K E _

Solid state relay
Number of poles
Switching mode
Rated operational voltage
Control voltage
Rated operational current
Connection type for control
Connection type for power
Connection configuration
Option

Ordering Key (Refer to page 2 and 3 for available part numbers)

1 Phase SSR Rated voltage, Control voltage Rated Connection Connection Connection
with heatsink Blocking voltage current at 40˚C

RGC1A: ZC
RGC1B: IO

24-190 VDC 25: 25AAC, 1800A²s M: Pluggable (OTP)
30: 30AAC, 1800A²s spring-loaded
32: 30 AAC, 18000A
32: 37 AAC, 18000A
40: 40AAC, 3200A²s
42: 43AAC, 18000A²s
60: 60AAC, 3200A²s
62: 65AAC, 18000A²s
90: 85AAC, 6600A²s
92: 85AAC, 18000A²s

4

23: 230V +10% - 15%, 800Vp D: 3 or 4-32VDC 15: 20AAC, 525A²s K: Screw K: Screw E: Contactor P: Overtemperature

4

60: 600V +10% -15%, 1200Vp A: 20 - 275VAC, 20: 23AAC, 525A²s G: Box clamp G: Box clamp protection

3

control pow er configuration Option

5

2

s

2

s

3. Refer to Derating Curves

4. ZC = Zero cross switching, IO= Instant ON switching

5. Default control connection for RGC...P is Box Clamp. See Connections Specifications

Specifications are subject to change without notice (22.05.2018) 1

RGC...E

Selection Guide

Rated voltage, Control voltage Connection Rated operational current @ 40oC (I2t value)
Blocking voltage, control/power Product width
Switching mode 20 AAC (525A²s) 23 AAC (525A²s) 25 AAC (1800A²s) 30 AAC (1800A²s)

230V, 800Vp 3-32VDC Screw/Screw RGC1A23D15KKE RGC1A23D20KKE RGC1A23D25KKE RGC1A23D30KKE
ZC Spring/Screw RGC1A23D15MKE RGC1A23D20MKE RGC1A23D25MKE RGC1A23D30MKE

Spring/Screw RGC1A23A15MKE RGC1A23A20MKE RGC1A23A25MKE RGC1A23A30MKE

40 AAC (3200A²s) 43 AAC (18000A²s) 60 AAC (3200A²s) 65 AAC (18000A²s)

3-32VDC Screw/Box RGC1A23D40KGE RGC1A23D42KGE RGC1A23D60KGE RGC1A23D62KGE
20-275VAC, 24-190VDC Screw/Box RGC1A23A40KGE RGC1A23A42KGE RGC1A23A60KGE RGC1A23A62KGE

20 AAC (525A²s) 23 AAC (525A²s) 25 AAC (1800A²s) 30 AAC (1800A²s)

600V, 1200Vp 4-32VDC Screw/Screw RGC1A60D15KKE RGC1A60D20KKE RGC1A60D25KKE RGC1A60D30KKE
ZC Spring/Screw RGC1A60D15MKE RGC1A60D20MKE RGC1A60D25MKE RGC1A60D30MKE

Spring/Screw RGC1A60A15MKE RGC1A60A20MKE RGC1A60A25MKE RGC1A60A30MKE

20-275VAC, 24-190VDC Screw/Screw RGC1A23A15KKE RGC1A23A20KKE RGC1A23A25KKE RGC1A23A30KKE

20-275VAC, 24-190VDC Screw/Screw RGC1A60A15KKE RGC1A60A20KKE RGC1A60A25KKE RGC1A60A30KKE

17.5mm, low depth 17.5mm 17.5mm, low depth 22.5mm

35mm 35mm 70mm 70mm

17.5mm, low depth 17.5mm 17.5mm, low depth 22.5mm

30 AAC (18000A²s) 37 AAC (18000A²s)

4-32VDC Screw/Screw RGC1A60D32KKE -
Spring/Screw RGC1A60D32MKE -
Screw/Box - RGC1A60D32KGE
Spring/Box - RGC1A60D32MGE

40 AAC (3200A²s) 43 AAC (18000A²s) 60 AAC (3200A²s) 65 AAC (18000A²s)

4-32VDC Screw/Box RGC1A60D40KGE RGC1A60D42KGE RGC1A60D60KGE RGC1A60D62KGE
Spring/Box RGC1A60D40MGE RGC1A60D42MGE - RGC1A60D62MGE

Spring/Box RGC1A60A40MGE RGC1A60A42MGE - RGC1A60A62MGE

20 AAC (525A²s) 23 AAC (525A²s) 25 AAC (1800A²s) 30 AAC (1800A²s)

600V, 1200Vp 4-32VDC Screw/Screw RGC1B60D15KKE RGC1B60D20KKE RGC1B60D25KKE RGC1B60D30KKE
IO

40 AAC (3200A²s) 43 AAC (18000A²s) 60 AAC (3200A²s) 65 AAC (18000A²s)

4-32VDC Screw/Box RGC1B60D40KGE RGC1B60D42KGE RGC1B60D60KGE RGC1B60D62KGE

20-275VAC, 24-190VDC Screw/Box RGC1A60A40KGE RGC1A60A42KGE RGC1A60A60KGE RGC1A60A62KGE

17.5mm, low depth 17.5mm, low depth

35mm 35mm 70mm 70mm

17.5mm, low depth 17.5mm 17.5mm, low depth 22.5mm

35mm 35mm 70mm 70mm

2 Specifications are subject to change without notice (22.05.2018)

RGC...E

Selection Guide - RGC..P (Integrated Overtemperature Protection)

Rated voltage, Control voltage Connection Rated operational current @ 40oC (I2t value)
Blocking voltage, control / power Product width
Switching mode 30 AAC (1800A²s)

22.5mm

600V, 1200Vp 5-32VDC Box/Screw RGC1A60D30GKEP
ZC

43 AAC (18000A²s) 65AAC (18000A²s) 85AAC (6600A²s) 85AAC (18000A²s)

5-32VDC Box/Box RGC1A60D42GGEP RGC1A60D62GGEP RGC1A60D90GGEP RGC1A60D92GGEP

20-275VAC, 24-190VDC Box/Screw RGC1A60A30GKEP

35mm 70mm 70mm + fan 70mm + fan

20-275VAC, 24-190VDC Box/Box RGC1A60A42GGEP RGC1A60A62GGEP RGC1A60A90GGEP RGC1A60A92GGEP

Output Voltage Specifications

RGC..23.. RGC..60..

Operational voltage range 24-240 VAC, 42-600 VAC,
+10%, -15% on max +10% -15% on max

Blocking voltage 800Vp 1200 Vp
Internal varistor 275V 625V

General Specifications

Latching voltage
(across L1-T1) 20V

Operational frequency
range 45 to 65Hz

Power factor > 0.5 @ Vrated
Touch Protection IP20
Control input status continuously ON Green LED,

when control input is applied
Pollution degree 2

(non-conductive pollution with
possibilities of condensation)

Rated impulse withstand 6 kV (1.2/50μs) for voltage,
Uimp
Over-voltage category III

(fixed installations)
Isolation
Input to Output RGC... 4000 Vrms

RGC...D..P 2500 Vrms
RGC...A..P 4000 Vrms
Input and Output RGC... 4000 Vrms
to case RGC...D..P 4000 Vrms
RGC...A..P 4000 Vrms
Input to Fan/ Alarm Output
RGC...A..P 2500 Vrms

Specifications are subject to change without notice (22.05.2018) 3

RGC...E

Output Specifications

RGC..15.. RGC..20.. RGC..25.. RGC..30..
Rated operational current

6

RGC..32..KE

RGC..32..GE

AC-51 rating @ Ta=25°C 20 AAC 25.5 AAC 30 AAC 30 AAC 30 AAC 43 AAC
AC-51 rating @ Ta=40°C 20 AAC 23 AAC 25 AAC 30 AAC 30 AAC 37 AAC
AC-53a rating @ Ta=40°C 5 AAC 5 AAC 5 AAC 8 AAC 5 AAC 5 AAC
Number of motor starts per hour

(x:6, Tx:6s, F:50%) at 40˚C

7

30 30 30 30 30 30
Min. operational current 150 mAAC 150 mAAC 250 mAAC 250 mAAC 500 mAAC 500 mAAC
Rep. overload current -

(Motor Rating) PF = 0.4 - 0.5
UL508: T

=40°C, tON=1s, t

AMB

=9s,

OFF

50 cycles 51 AAC 60 AAC 51 AAC 84 AAC 51 AAC 51 AAC

Maximum transient surge current (I

), t=10ms 325 Ap 325 Ap 600 Ap 600 Ap 1900 Ap 1900 Ap

TSM

Maximum off-state leakage current
at rated voltage 3 mAAC 3 mAAC 3 mAAC 3 mAAC 3 mAAC 3 mAAC

I²t for fusing (

t=10ms), Minimum 525 A²s 525 A²s 1800 A²s 1800 A²s 18000 A²s 18000 A²s

Crititcal dv/dt (@ Tj init = 40°C) 1000 V/μs 1000 V/μs 1000 V/μs 1000 V/μs 1000 V/μs 1000 V/μs

RGC..40.. RGC..42.. RGC..60.. RGC..62.. RGC..90.. RGC..92..
Rated operational current

6

AC-51 rating @ Ta=25°C 47 AAC 50 AAC 70 AAC 75 AAC 85 AAC 85 AAC
AC-51 rating @ Ta=40°C 40 AAC 43 AAC 60 AAC 65 AAC 85 AAC 85 AAC
AC-53a rating @ Ta=40°C 13 AAC 16 AAC 14.8 AAC 20 AAC 18 AAC 20 AAC
Number of motor starts per hour

(x:6, Tx:6s, F:50%) at 40˚C

7

30 30 30 30 30 30
Min. operational current 400 mAAC 500 mAAC 400 mAAC 500 mAAC 400 mAAC 500 mAAC
Rep. overload current -

(Motor Rating) PF = 0.4 - 0.5
UL508: T

=40°C, tON=1s, t

AMB

=9s,

OFF

50cycles 126 AAC 126 AAC 126 AAC 168 AAC 168 ACC 168 AAC

Maximum transient surge current (I

), t=10ms 800 Ap 1900 Ap 800 Ap 1900 Ap 1150 Ap 1900 Ap

TSM

Maximum off-state leakage current
at rated voltage 3 mAAC 3 mAAC 3 mAAC 3 mAAC 3 mAAC 3 mAAC

I²t for fusing (

t=10ms), Minimum 3200 A²s 18000 A²s 3200 A²s 18000 A²s 6600 A²s 18000 A²s

Crititcal dv/dt (@ Tj init = 40°C) 1000 V/μs 1000 V/μs 1000 V/μs 1000 V/μs 1000 V/μs 1000 V/μs

6. See Derating Curves

7. Overload profile for AC-53a;
Ie: AC-53a: x-Tx: F-S, where Ie = nominal current (AC-53a AAC), x = overload current factor, Tx = duration of overload current (s), F = duty cycle (%), S = number
of starts per hour. Example; 5A: AC-53a: 6 - 6 : 50 - 30 = max. 30 starts for the RGC..15 with an overload profile of 30A for 6 seconds with a duty cycle of 50%

Overtemperature Alarm Specifications for RGC...P

RGC..D..P RGC..A..P
Output type PNP open collector Potential Free
Normal state Closed Closed
Maximum current rating 50 mADC 50 mADC
Rated voltage (EN61131-2: 2003)
Rated voltage, Us RGC...D9xGGEP 24VDC ± 10% N/A
Fan rating, U

f RGC...A9xGGEP N/A 24VDC ±10%, 50mA nominal

Alarm voltage drop Typical 2.8VDC 1.8VDC
Maximum 4VDC 3.5VDC

Visual Indication Continous Red LED Continous Red LED
Reverse polarity protection 24VDC 24VDC

8. DC supply for alarm signal should be supplied from a Class 2 power source

9. Maximum voltage to be applied between 11+ and 12- (Ua) terminals should be 35VDC maximum with reference to A2-

4 Specifications are subject to change without notice (22.05.2018)

8, 9

, Ua 24VDC -15%, +20% 24VDC -15%, +20%

RGC...E

Input Specifications

RGC..D.. RGC..A..

Control voltage range
24 (-10%) - 190 VDC

RGC..60.. 4 - 32 VDC 20-275 VAC,
24 (-10%) - 190 VDC

RGC...P (Uc) 5 - 32 VDC 20-275 VAC,
24 (-10%) - 190 VDC

Pick-up voltage RGC..23.. 3.0 VDC 20 VAC/DC
RGC..60.. 3.8 VDC
RGC...P 5 VDC 20 VAC/ 24VDC

Drop-out voltage 1 VDC 5 VAC/DC
Maximum Reverse voltage 32 VDC ­Response time pick-up (RGC1A..)

@ 230VAC/110VDC

Response time pick-up (RGC1B..) 350µs @ 24 VDC N/A
Response time drop-out 0.5 cycle
Input current @ 40°C See diagrams below See diagrams below

10. DC control to be supplied by class 2 power source according to UL1310

11. For GL approved models control range for RGC1.23... is 4-32VDC and for RGC1.60... 5-32VDC

RG..A..

10, 11

RGC..23.. 3 - 32 VDC 20 - 275 VAC,

0.5 cycle + 500µs @ 24VDC 2 cycles

+ 500µs @ 24VDC

0.5 cycle + 40ms @ 230VAC/110VDC

RGC1 .. A : input current vs input voltage

RGC1 .. A : input current vs input voltage

40mA

40mA

35mA

35mA

30mA

30mA

25mA

25mA

RGC .. A

20mA

20mA

15mA

15mA

10mA

5mA

0mA

0VAC 50VAC100VAC 150VA C 200VAC 250VA C 300VAC

40mA

40mA

35mA

35mA

30mA

30mA

25mA

25mA

20mA

20mA

15mA

15mA

RGC..A..P
(Active Protection)

RGC..A..P
(Active Protection)

RGC1 .. A : input current vs input voltage

RGC1 .. A : input current vs input voltage

RGC .. A

RGC .. A

RGC..A..P
(Normal Operation)

10mA

5mA

0mA

0VDC 50VDC100VDC150VDC200VDC250VDC

RGC..A..P
(Normal Operation)

Specifications are subject to change without notice (22.05.2018) 5

RGC...E

Input Specifications (cont.)

RG..D..

A1 Characteristics: DC input current vs Input voltage

25.0mA

25.0mA

20.0mA

20.0mA

15.0mA

15.0mA

10.0mA

10.0mA

5.0mA

x: Input currents for all models except RGC1..D90GGEP and RGC1..D92GGEP

20.0mA

20.0mA

15.0mA

15.0mA

10.0mA

10.0mA

RGC..D..P
(Normal Operation)

RGC..D..P
(Active Protection)

2V 4V 6V 8V 10V12V 14V16V 18V20V 22V 24V 26V 28V 30V 32V 34V

RGC..D9xGGEP
(Normal Operation)

A1 Characteristics: DC input current vs Input voltage

IN1 Characteristics: DC input current vs Input voltage

IN1 Characteristics: DC input current vs Input voltage

x

y

x

5.0mA

5.0mA

0.0mA

RGC..D9xGGEP
(Active Protection)

2V 4V 6V 8V 10V 12V 14V 16V 18V 20V 22V 24V 26V 28V 30V 32V 34V

y: input currents valid only for RGC1..D90GGEP and RGC1..D92GGEP

Motor Ratings: HP (UL508) / kW (EN/IEC60947-4-2) @ 40°C

115 VAC 230 VAC 400 VAC 480 VAC 600 VAC

RGC..15
RGC..20 ½HP / 0.18kW 1½HP / 0.37kW 2HP / 0.75kW 3HP / 1.1kW 3HP / 1.5kW
RGC..25
RGC..30 ¾HP / 0.37kW 2HP / 1.1kW 3HP / 1.5kW 5HP / 2.2kW 5HP / 3.7kW
RGC..32
RGC..40 1HP / 0.56kW 3HP / 1.5kW 5HP / 2.2kW 5HP / 3.7kW 7½HP / 4kW
RGC..42 1½HP / 0.56kW 3HP / 1.5kW 5HP / 2.2kW 7½HP / 3.7kW 10HP / 4kW
RGC..60 1½HP / 0.56kW 3HP / 1.5kW 5HP / 3kW 7½HP / 4kW 10HP / 4kW
RGC..62 2HP / 0.75kW 5HP / 1.5kW 7½HP / 4kW 10HP / 4kW 15HP / 5.5kW
RGC..90 2HP / 0.75kW 5HP / 1.5kW 7½HP / 4kW 10HP / 4kW 15HP / 5.5kW
RGC..92 2HP / 0.75kW 5HP / 1.5kW 7½HP / 4kW 10HP / 4kW 15HP / 5.5kW

1

/3HP / 0.18kW 1HP / 0.37kW 2HP / 0.75kW 3HP / 1.1kW 3HP / 1.5kW

1

/3HP / 0.18kW 1HP / 0.37kW 2HP / 0.75kW 3HP / 1.1kW 3HP / 1.5kW

1

/3HP / 0.18kW 1HP / 0.37kW 2HP / 0.75kW 3HP / 1.1kW 3HP / 1.5kW

6 Specifications are subject to change without notice (22.05.2018)

RGC...E

Detailed Over temperature Alarm Procedure (for RGC...P)

ALARM Signal and Fan
(applicable to RGC..D90GGEP)
(applicable to RGC..D92GGEP)

ALARM Signal only

ALARM Signal onlyALARM Signal and FAN

START

START

Is Chip

Is Chip

temperature >

temperature >

115°C ?

115°C ?

Y

Y

FAN: ON

FAN: ON

Chip

Is Chip

temperature <

temperature <

85°C ?

85°C ?

Y

Y

FAN: OFF

FAN: OFF

N

N

N

N

temperature

temperature

limitreached?

limitreached?

SSRoutput: OFF

SSRoutput: OFF
Red LED: ON

Red LED: ON
AlarmSignal: ON

AlarmSignal: ON

Is Chip

temperature <

80°C?

SSR output: ON
Red LED: OFF
Alarm Signal: OFF
FAN: OFF

Chip

Chip

START

START

Chip

Chip

temperature

temperature

limit reached?

limit reached?

SSRoutput: OFF

SSRoutput: OFF
Red LED: ON

Red LED: ON
AlarmSignal: ON

AlarmSignal: ON

N

N

Y

Y

Chip

Chip

temperature <

temperature <

80°C?

80°C?

SSR output: ON

SSR output: ON
Red LED: OFF

Red LED: OFF
Alarm Signal: OFF

Alarm Signal: OFF

N

N

Y

Y

N

N

Y

Y

N

Y

CAUTION

• Alarm condition resets whenever the voltage signal is removed from terminal A1 (+)

• In the case of RGC1A60D9xGGEP, if the voltage signal is not applied across A1(+) and A2 (-) terminals, the overtemperature detection and functionality is
lost (including fan operation and alarm signalling)

• In the case of RGC1A60A9xGGEP it is necessary to supply IN2 and IN3 with 24VDC for fan operation.

• Alarm procedure for RGC1A60A9xGGEP follows ‘Alarm signal only’ flow since fan is continously operating.

• Alarm condition automatically resets ONLY when power semiconductor temperature < 80˚C

• Temperatures indicated are typical figures.

Specifications are subject to change without notice (22.05.2018) 7

RGC...E

Output Power Dissipation

100

90

80

70

60

50

40

PowerDissipationinW

30

20

RGC..15,20

RGC..25,30

RGC..40,60

RGC..90

RGC..32,42,62,92

10

0

0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85

LoadCurrentinAACrms

8 Specifications are subject to change without notice (22.05.2018)

RGC...E

8

10

12

14

16

18

20

22

24

26

28

30

32

34

36

38

40

42

44

0 10 20 30 40 50 60 70 80

LoadCurrentinAACrms

SurroundingAmbientTemperaturein°C

RGC..32.GE

RGC..32.KE

RGC..30

RGC..25

RGC..20

RGC..15

0

10

20

30

40

50

60

70

80

90

0 10 20 30 40 50 60 70 80

LoadCurrentinAACrms

SurroundingAmbientTemperatureinoC

RGC..92
RGC..90

RGC..62

RGC..60

RGC..42

RGC..40

Current Derating (UL508)

RGC...P models max. operating temperature is + 70˚C

Specifications are subject to change without notice (22.05.2018) 9

RGC...E

e

20

e

5mm

0

5

10

15

20

25

30

01020304050607080

Load Current in AAC

Surrounding Ambient Temperature in °C

0mm

5mm

10mm

22.5mm & over

Derating vs. Spacing Curves

RGC.. 15..

25

20

15

nt in AAC

Load Curr

RGC.. 20..

nt in AAC

Load Curr

10

5

0

0 10 20 30 40 50 60 70 80

Surrounding Ambient Temperature in °C

35

30

25

15

10

5

0

0 10 20 30 40 50 60 70 80

Surrounding Ambient Temperature in °C

0mm

5mm

10mm &
over

0mm

10mm

20mm &
over

RGC.. 25.

10 Specifications are subject to change without notice (22.05.2018)

RGC...E

25

n

35

40

45

50

nt in AAC

0mm

10mm &

10

15

20

25

30

0 10 20 30 40 50 60 70 80

Load Curre

Surrounding Ambient Temperature in °C

over

Stand
alone
unit

LoadCurrentinAAC

0mm

5mm

20mm

Standalone

Derating vs. Spacing Curves

RGC.. 30..

35

30

t in AAC

20

Load Curre

15

10

0 10 20 30 40 50 60 70 80

Surrounding Ambient Temperature in °C

0mm

5mm

10mm &
over

Stand
alone unit

RGC.. 32..

RGC.. 40..

40

35

30

25

20

15

10

5

0

0 10 20 30 40 50 60 70 80

SurroundingAmbientTemperaturein°C

0mm

5mm

20mm

Standalone

Specifications are subject to change without notice (22.05.2018) 11

RGC...E

60

65

70

nt in AAC

0mm

30

35

40

45

50

55

0 10 20 30 40 50 60 70 80

Load Curr

e

Surrounding Ambient Temperature in °C

10mm &
over

Stand
alone unit

Derating vs. Spacing Curves

RGC.. 42.

RGC.. 60..

RGC.. 62.

12 Specifications are subject to change without notice (22.05.2018)

7

5

80

85

90

nt in AAC

0mm

50

55

60

65

70

5

0 10 20 30 40 50 60 70

Load Curr

e

Surrounding Ambient Temperature in °C

10mm &
over

Stand
alone unit

RGC...E

Derating vs. Spacing Curves

RGC.. 90GGEP, RGC..92GGEP

Environmental Specifications

Operating temperature12 -40°C to 80°C (-40˚F to +176˚F)
Storage temperature -40°C to 100°C (-40˚F to +212˚F)
EU RoHS compliant Yes
China RoHS compliant Refer to Environmental

Information (page 29)
Impact resistance

(EN50155, EN61373) 15/11 g/ms
Vibration resistance

(2-100Hz, IEC60068-2-6,
EN50155, EN61373) 2g per axis

Weight
RGC..15 approx. 260g
RGC..20 approx. 315g
RGC..25 approx. 260g
RGC..32 approx. 260g
RGC..32..GE approx. 269g

Agency Approvals and Conformances

Conformance IEC/EN 62314
IEC/EN 60947-4-2
IEC/EN 60947-4-3

Relative humidity 95% non-condensing @ 40˚C
UL flammability rating

(housing) UL 94 V0
Glow wire ignition temperature
and Glow wire flammability
index conform to EN 60335-1
requirements

Installation altitude 0 - 1000m. Above 1000m
derate linearly by 1% of FLC
per 100m up to maximum of
2000m

RGC..30 (P) approx. 375g (412g)
RGC..4x (P) approx. 515g (581g)
RGC..6x (P) approx. 972g (1020g)
RGC..9x P approx. 1100g

Agency Approvals UL508 Listed (E172877)
cUL Listed (E172877)
VDE 0660-109
GL

Short Circuit Current Rating 100kA, UL508

13

14

12. Operating temperature range for RGC..P (overtemperature protection) is -30˚C to 70˚C (-22˚F to 158˚F)

13. Applicable to models RGC1...15.KE, RGC1...20.KE, RGC1..25..KE and RGC1...30.KE

14. RGC..32 models are not VDE approved

Specifications are subject to change without notice (22.05.2018) 13

RGC...E

Electromagnetic Compatibility

EMC Immunity EN 60947-4-3
Electrostatic Discharge (ESD)
Immunity IEC/EN 61000-4-2

Air discharge, 8kV Performance Criteria 1
Contact, 4kV Performance Criteria 1

Electrical Fast Transient
(Burst) Immunity IEC/EN 61000-4-4

Output: 2kV, 5kHz Performance Criteria 1
Input: 1kV, 5kHz Performance Criteria 1
Electrical Surge Immunity IEC/EN 61000-4-5

(for RGC...E)
Output, line to line, 1kV Performance Criteria 1
Output, line to earth, 2kV Performance Criteria 1
Input, line to line, 1kV Performance Criteria 2
Input, line to earth, 2kV Performance Criteria 2

EMC Emission EN 60947-4-3
Radio Interference

Voltage Emission (Conducted) IEC/EN 55011

0.15 - 30MHz Class A (industrial) with filters

- see filter information

Electrical Surge Immunity IEC/EN 61000-4-5
(for RGC...EP)

Output, line to line, 1kV Performance Criteria 1
Output, line to earth, 2kV Performance Criteria 1
DC lines, line to line, 500V Performance Criteria 2
DC lines, line to earth, 500V Performance Criteria 2
Signal lines, line to earth, 1kV Performance Criteria 2

Radiated Radio Frequency
Immunity IEC/EN 61000-4-3

10V/m, 80 - 1000 MHz Performance Criteria 1
10V/m, 1.4 - 2 GHz Performance Criteria 1
3V/m, 2 - 2.7 GHz Performance Criteria 1

Conducted Radio Frequency IEC/EN 61000-4-6
Immunity

10V/m, 0.15 - 80 MHz Performance Criteria 1
Voltage Dips Immunity IEC/EN 61000-4-11
0% for 0.5, 1 cycle Performance Criteria 2
40% for 10 cycles Performance Criteria 2
70% for 25 cycles Performance Criteria 2
80% for 250 cycles Performance Criteria 2
Voltage Interruptions Immunity IEC/EN 61000-4-11

0% for 5000ms Performance Criteria 2

Radio Interference
Field Emission (Radiated) IEC/EN 55011

30 - 1000MHz Class A (industrial)

14 Specifications are subject to change without notice (22.05.2018)

RGC...E

Filtering - EN / IEC 55011 Class A compliance (for class B compliance contact us)

Part Number Suggested filter for compliance Maximum Heater current

RGC1A23..15 68nF/ 275 V / X1 20A
RGC1A23..20 68nF/ 275 V / X1 20A
RGC1A23..25, RGC1A23..30 220 nF / 275V / X1 30A
RGC1A23..40 220 nF / 275V / X1 30A

330 nF / 275V / X1 45A
RGC1A23..60 220 nF / 275V / X1 30A

330 nF / 275V / X1 45A
RGC1A23..42, RGC1A23..62 330 nF / 275V / X1 35A

680 nF / 275V / X1 65A
RGC1A60..15 100 nF / 760V / X1 20A
RGC1A60..20 100 nF / 760V / X1 20A
RGC1A60..25, RGC1A60..30 220 nF / 760V / X1 30A
RGC1A60..40 220 nF / 760V / X1 25A

330 nF / 760V / X1 45A
RGC1A60..60 220 nF / 760V / X1 25A

330 nF / 760V / X1 45A
RGC1A60..32, RGC1A60..42, 330 nF / 760V / X1 40A

RGC1A60..62, RGC1A60..9x 680 nF / 760V / X1 65A

Note:

• Control input lines must be installed together to maintain products’ susceptability to Radio Frequency interference.

• Use of AC solid state relays may, according to the application and the load current, cause conducted radio interferences. Use of mains filters may be
necessary for cases where the user must meet E.M.C requirements. The capacitor values given inside the filtering specification tables should be taken only
as indications, the filter attenuation will depend on the final application.

• Performance Criteria 1: No degradation of performance or loss of function is allowed when the product is operated as intended.

• Performance Criteria 2: During the test, degradation of performance or partial loss of function is allowed. However when the test is complete the
product should return operating as intended by itself.

• Performance Criteria 3: Temporary loss of function is allowed, provided the function can be restored by manual operation of the controls.

Filter Connection Diagrams

1 Phase

L1

L2

L3

N

3 Phase

SSR

SSR

SSR

R

d

R

d

R

d

LOAD

R

= 1MΩ, 0.5W

d

Filter has to be connected
across both LOAD and SSR

Specifications are subject to change without notice (22.05.2018) 15

RGC...E

L1

L1

Functional Diagram (Without OTP)

DC control

+

A1

()

A2( )

AC control

A1

()

A2( )

~

-

+
~

-

REGULATION

REGULATION

T1

ZC

IO

T1

ZC

Connection Diagram (Without OTP)

L1

L2/N

Control
input

* depends on system requirements

*

Load

16 Specifications are subject to change without notice (22.05.2018)

Load

Control
input

L1

L2/N

*

Load

L1

L2/N

*

12L1

T1

hc
ti
w
SetatSd

i

lo
SGR

FAULT

CON TRO L

A1

A2

GNDG

N

D

S

U

P

PL

Y

ALAR

M

A

LA

R

M

11 +

12 -

RGC...E

Connection Diagram (with OTP)

DC Control

RGC1...D30GKEP, RGC1...D4xGGEP,
RGC1...D6xGGEP

RGC1...D9xGGEP

Uc: 5 - 32 VDC
Ua: max 35VDC
Alarm Output: max. 50mA

A1, A2: Control voltage
11, 12: Alarm output

Uc: 5 - 32 VDC
Us: 24 VDC
Alarm Output: max. 50mA

Note: Fan is internally
supplied

A1, A2: Supply voltage
IN1: Control voltage
OUT: Alarm output

AC Control

RGC1...A30GKEP, RGC1...A4xGGEP,
RGC1...A6xGGEP

* depends on system requirements

Uc: 24 - 275 VAC
24 - 190 VDC
Ua: max 35VDC
Alarm Output: max. 50mA

A1, A2: Control voltage
11, 12: Alarm output

RGC1...A9xGGEP

Uc: 24 - 275 VAC
24 - 190 VDC
Ua: max. 35 VDC
Alarm Output: max. 50mA
U

f: 24 VDC (needs to be

supplied externally)

A1, A2: Control voltage
11, 12: Alarm output
IN2, IN3: Fan supply

Specifications are subject to change without notice (22.05.2018) 17

RGC...E

17.8

98.5
51

35.5

9.5

17.8

9.5

5

3.2

35.5

45.5

5

3.2

109.5

92

1069890

1069890

43.8

43.8

Terminal Layout and Dimensions

RGC...15KKE, RGC...25KKE, RGC...32KKE

RGC...15MKE, RGC...25MKE, RGC..32MKE

12L1

hctiwS etatS diloS GR

A1 L1

T1A2

ON

A2

A1

T1

1/L1: Supply connection
2/T1: Load connection
A1 (+): Positive control signal
A2 (-): Control ground
: Protective earth

Housing width tolerance +0.5mm, -0mm…as per DIN43880.

All other tolerances ± 0.5mm.

All dimensions in mm.

18 Specifications are subject to change without notice (22.05.2018)

17.8

98.5
51

35.5

9.5

5

3.2

1069890

43.8

17.8

98.5
51

35.5

9.5

17.8

9.5

5

3.2

35.5

45.5

5

3.2

109.5

92

1069890

1069890

43.8

43.8

RGC...E

Terminal Layout and Dimensions (cont).

RGC..32KGE

RGC..32MGE

1/L1: Supply connection
2/T1: Load connection
A1 (+): Positive control signal
A2 (-): Control ground
: Protective earth

12L1

hctiwS etatS diloS GR

A1 L1

T1A2

ON

A2

A1

L11

T12

T1

Housing width tolerance +0.5mm, -0mm…as per DIN43880.

All other tolerances ± 0.5mm.

All dimensions in mm.

Specifications are subject to change without notice (22.05.2018) 19

RGC...E

17.8
136

51

35.5

9.5

17.8

22.5

9.5

5

3.2

136

51

35.5

9.5

5

3.2

35.5

45.5

5

3.2

17.8

147

129.5

1069890

1069890

1069890

43.8

43.8

43.8

Terminal Layout and Dimensions (cont).

RGC...20KKE

RGC...20MKE

12L1

hctiwS etatS diloS GR

A1 L1

T1A2

ON

A2

A1

T1

RGC...30KKE

1/L1: Supply connection
2/T1: Load connection
A1 (+): Positive control signal
A2 (-): Control ground
: Protective earth

Housing width tolerance +0.5mm, -0mm…as per DIN43880.

All other tolerances ± 0.5mm.

All dimensions in mm.

20 Specifications are subject to change without notice (22.05.2018)

22.5

9.5

3.2

5

147

129.5

35.6

136

51

43.7

5

3.2

5

3.2

35.6

147

129.5

27.2

27.2

43.8

106

98

90

106

98

90

43.8

43.8

RGC...E

Terminal Layout and Dimensions (cont.)

RGC...30MKE

12L1

h
c

A1 L1

t

i
w
S

e
ta
t
S

d
i

l
o

T1A2

S

G

R

ON

A2

A1

RGC...40KGE, RGC...42KGE

RGC...40MGE, RGC...42MGE

T1

1/L1: Supply connection
2/T1: Load connection
A1 (+): Positive control signal
A2 (-): Control ground
: Protective earth

Housing width tolerance +0.5mm, -0mm…as per DIN43880.

All other tolerances ± 0.5mm. All dimensions in mm.

Specifications are subject to change without notice (22.05.2018) 21

RGC...E

136

5

69.1

35.6

27.2

3.2
106

98

90

43.8

51

43.7

h
c

t

i
w
S

e
ta
t
S

d
i

l
o
S

G

R

ON

A1 L1

T1A2

A1

A2

12L1

T1

22.5

9.5

3.2

5

147

129.5

35.6

136

51

43.7

5

3.2

5

3.2

35.6

147

129.5

27.2

27.2

43.8

106

98

90

106

98

90

43.8

43.8

Terminal Layout and Dimensions (cont.)

RGC...60KGE, RGC...62KGE

RGC...62MGE

1/L1: Supply connection
2/T1: Load connection
A1 (+): Positive control signal

A2 (-): Control ground
: Protective earth

Housing width tolerance +0.5mm, -0mm…as per DIN43880.

All other tolerances ± 0.5mm.

All dimensions in mm.

22 Specifications are subject to change without notice (22.05.2018)

RGC...E

136

5

69.1

35.6

27.2

3.2

22.5

5

5

163

35.5

78

22.5

9.5

163

78

35.5

17.8

9.5

106

98

90

106

98

90

106

98

90

43.8

51

43.7

12L1

T1

h
c
t

i
w
S

e
t
a

t
S

d
i

l
o
S
G

R

F

AU

L

T

CONTROL

A1

A2

GNDGND

SUPP

L

Y

ALARM

ALARM

11+

12 -

Terminal Layout and Dimensions (cont.)

RGC...30GKEP

12L1

1/L1: Supply connection
2/T1: Load connection
A1 (+): Positive control signal

A2 (-): Control ground
11 + : Alarm output (+)
12 - : Alarm output (-)

: Protective earth

ALARM

11+

h
c
t

i
w
S

e
t
a

t
S

d
i

l
o
S
G

R

ALARM

12 -

CONTROL

F

AU

L

SUPP

L

Y

A1

T

A2

GNDGND

T1

Housing width tolerance +0.5mm, -0mm…as per DIN43880.

All other tolerances ± 0.5mm.

All dimensions in mm.

Specifications are subject to change without notice (22.05.2018) 23

167.8

5

35.6

27.2

69.1

27.2

69.1

27.2

126

98

90

60.5

5

163

43.7

78

5

163

78

43.7

106

98

90

106

98

90

60.5

163

78

43.7

RGC...E

Terminal Layout and Dimensions (cont.)

RGC...40GGEP, RGC...42GGEP

A1A211+

12-

A1A211+

12-

IN3IN2

RGC...60GGEP, RGC...62GGEP

A1A211+

12-

A1A211+

12-

A1A211+

12-

IN3IN2

IN3IN2

IN3IN2

RGC...90GGEP, RGC...92GGEP

ALARM

SUPPLY

CONTROL

A1

OUT

IN

1

hctiwS etatS diloS G

CONTROL

R

FAULT

A2

3

IN

2

IN

FAN -

FAN +

GND

GND

A1A211+

12-

A1A211+

12-

IN3IN2

IN3IN2

RGC...D9xGGEP RGC...A9xGGEP

1/L1: Supply connection
2/T1: Load connection
A1 (+): Positive control signal
(Positive supply in case of RGC1A60D9xGGEP)
A2 (-): Control ground
IN1: Control signal (only for RGC1A60D9xGGEP)
IN2: Fan + supply (only for RGC1A60A9xGGEP)
IN3: Fan - supply (only for RGC1A60A9xGGEP)
11 + : Alarm output (+)
OUT, 12 - : Alarm output (-)
: Protective earth

Housing width tolerance +0.5mm, -0mm…as per DIN43880.

All other tolerances ± 0.5mm. All dimensions in mm.

24 Specifications are subject to change without notice (22.05.2018)

X

X

X

X

X

X

X

X

X

X

X

X

RGC...E

Connection Specifications

POWER CONNECTIONS: 1/L1, 2 /T1
Use 75°C copper (Cu) conductors

Stripping Length (X) 12mm 11mm
Connection type M4 screw with captivated washer M5 screw with box clamp
Rigid (Solid & Stranded)

UL / cUL rated data

X

2 x 2.5..6 mm
2 x 14.. 10 AWG

Flexible with end sleeve 2 x 1.0 ... 2.5mm

2 x 14.. 12 AWG

Flexible without 2 x 1.0 ... 2.5mm
end sleeve 2 x 2.5.. 6mm

2 x 18.. 14 AWG
2 x 14.. 10 AWG

Torque specifications Pozidriv 2 Posidriv 2
UL: 2Nm (17.7lb-in) UL: 2.5Nm (22lb-in)
IEC: 1.5 - 2.0Nm (13.3 - 17.7lb-in)

Aperture for termination lug 12.3mm N/A

Protective Earth (PE) Connection

M5, 1.5Nm (13.3 lb-in)

RGC...KKE ; RG..GKEP. ; RG...MKE RG...KGE ; RG...GGEP ; RG...MGE

2 x 2.5..4mm

2

2 x 18.. 14 AWG

2

1 x 2.5..6 mm
1 x 14.. 10 AWG 1 x 14...3 AWG

2

1 x 1.0..4mm

1 x 18.. 12 AWG 1 x 14.. 6 AWG

2

2

1 x 1.0.. 6mm

1 x 18.. 10 AWG 1 x 12.. 3 AWG

2

2

2

1 x 2.5..25mm2

1 x 2.5..16mm

2

1 x 4.. 25mm2

IEC: 2.5 - 3.0Nm (22-26.6lb-in)

Note: M5 PE screw not provided with SSR. PE connection required when product is intended to be used in Class 1 applications according to EN/IEC 61140.

CONTROL CONNECTIONS: A1(+), A2(-)

Use 60/75°C copper (Cu) conductors

RG...KKE, RG..KGE RG....MKE, RG...MGE

Torque specifications M3, Pozidriv 1
UL: 0.5Nm (4.4lb-in)
IEC: 0.5 - 0.6Nm (4.4 - 5.3lb-in)

Stripping Length (X) 8mm 12 - 13mm
Rigid (Solid & Stranded)

UL/ cUL rated data

2 x 0.5..2.5mm
2 x 18..12 AWG

Flexible with end sleeve
2 x 0.5..2.5mm
2 x 18..12AWG

X

2

1 x 0.5..2.5mm

1 x 18..12 AWG 1 x 24...12 AWG

2

1 x 0.5..2.5mm2

1 x 18..12AWG

2

1 x 0.2...2.5mm2

CONTROL CONNECTIONS: A1(+), A2(-), IN1, IN2, IN3, 11 (+), 12(-), OUT
Use 60/75°C copper (Cu) conductors RG...GGEP
Torque specifications M3, Pozidriv 1

UL: 0.5Nm (4.4lb-in)
IEC: 0.4 - 0.5Nm (3.5 - 4.4lb-in)

Stripping Length (X) 6mm 6mm
Rigid (Solid & Stranded)

UL/ cUL rated data

2 x 1.0..2.5mm
2 x 18..14 AWG

Flexible with end sleeve
2 x 1.0..2.5mm
2 x 18..14 AWG

X

2

1 x 1.0 ..2.5mm

1 x 18..14 AWG

2

1 x 1.0..2.5mm2

1 x 18..14AWG

2

Specifications are subject to change without notice (22.05.2018) 25

RGC...E

Installation Instructions

Y1 = 50mm

RGC RGC

20mm

Y2 =
100mm

X

Mounting on DIN rail

Mounting on DINrail

Dismounting from DIN rail

Dismountingfrom DINrail

20mm

X

X= 20mm

X = Refer to
Derating vs.
Spacing Curves

RGC

50mm

Short Circuit Protection

Protection Co-ordination, Type 1 vs Type 2:

Type 1 protection implies that after a short circuit, the device under test will no longer be in a functioning state. In type 2 co-ordination the device under
test will still be functional after the short circuit. In both cases, however the short circuit has to be interrupted. The fuse between enclosure and supply shall
not open. The door or cover of the enclosure shall not be blown open. There shall be no damage to conductors or terminals and the condcutors shall not
separate from terminals. There shall be no breakage or cracking of insulating bases to the extent that the integrity of the mounting of live parts is impaired.
Discharge of parts or any risk of fire shall not occur.

The product variants listed in the table hereunder are suitable for use on a circuit capable of delivering not more than 100,000A rms Symmetrical Amperes,
600 Volts maximum when protected by fuses. Tests at 100,000A were performed with Class J fuses, fast acting; please refer to the table below for maximum
allowed ampere rating of the fuse. Use fuses only.

Tests with Class J fuses are representative of Class CC fuses.

Co-ordination type 1 (UL508)

Part No. Prospective short Max. fuse size [A] Class Voltage [VAC]
circuit current [kArms]

RGC..15 100 30 J or CC max. 600
RGC..20 100 30 J or CC max. 600
RGC..25 100 30 J or CC max. 600

RGC..30 100 30 J or CC max. 600
RGC..32 100 80 J max. 600
RGC..40 100 40 J max. 600
RGC..42 100 90 J max. 600
RGC..60 100 40 J max. 600
RGC..62 100 90 J max. 600
RGC..90 100 40 J max. 600
RGC..92 100 90 J max. 600

26 Specifications are subject to change without notice (22.05.2018)

RGC...E

Co-ordination type 2 (IEC/EN 60947-4-2/ -4-3)

Part No. Prospective short Mersen (Ferraz Shawmut) Siba Voltage [VAC]

[kArms] size [A] Part number size [A] Part number

RGC..15 10 25 6.9xx CP GRC 14x51 /25 32 50 142 06.32 max. 600

100 25 6.9xx CP GRC 14x51 /25 32 50 142 06.32 max. 600

RGC..20 10 40 6.6xx CP URD 22x58 /40 32 50 142 06.32 max. 600

100 40 6.6xx CP URD 22x58 /40 32 50 142 06.32 max. 600

RGC..25 10 40 6.9xx CP GRC 22x58 /40 32 50 142 06.32 max. 600

100 40 6.6xx CP URD 22x58 /40 32 50 142 06.32 max. 600

RGC..30 10 40 6.9xx CP GRC 22x58 /40 32 50 142 06.32 max. 600

100 40 6.6xx CP URD 22x58 /40 32 50 142 06.32 max. 600

RGC..40 10 63 6.621 CP URGD 27x60 /63 63 50 194 20.63 max. 600

10 70 A70QS70-4 63 50 194 20.63 max. 600

100 63 6.621 CP URQ 27x60 /63 63 50 194 20.63 max. 600

RGC..32 10 63 6.9xx CP URC 14x51 /63 80 50 194 20.80 max. 600

RGC..42 10 70 A70QS70-4 80 50 194 20.80 max. 600

100 63 6.9xx CP URC 14x51 /63 80 50 194 20.80 max. 600

100 70 A70QS70-4 80 50 194 20.80 max. 600

RGC..60 10 80 6.621 CP URQ 27x60 /80 80 50 194 20.80 max. 600

up to 65AAC

100 n/a n/a 80 50 194 20.80 max. 600

RGC..62 10 100 6.9xx CP GRC 22x58 /100 100 50 194 20.100 max. 600

10 100 A70QS100-4 100 50 194 20.100 max. 600

100 100 6.621 CP URGD 27x60 /100 100 50 194 20.100 max. 600

100 100 A70QS100-4 100 50 194 20.100 max. 600

RGC..90 10 100 6.621 CP URQ 27x60 /100 100 50 194 20.100 max. 600

up to 80AAC

10 100 A70QS100-4 100 50 194 20.100 max. 600

100 n/a n/a 100 50 194 20.100 max. 600

RGC..92 10 125 6.621 CP URQ 27x60 /125 125 50 194 20.125 max. 600

10 125 A70QS125-4 125 50 194 20.125 max. 600

100 125 6.621 CP URQ 27x60 /125 125 50 194 20.125 max. 600

100 125 A70QS125-4 125 50 194 20.125 max. 600

circuit current Max fuse Max fuse

Specifications are subject to change without notice (22.05.2018) 27

RGC...E

Type 2 Protection with Miniature Circuit Breakers (M.C.B.s)

Solid State Relay ABB Model no. for ABB Model no. for Wire cross Minimum length of
type Z - type M. C. B. B - type M. C. B. sectional area [mm2] Cu wire conductor [m]

16

(rated current) (rated current)

RGC..15 1 pole
RGC..20 S201 - Z4 (4A) S201 - B2 (2A) 1.0 21.0

2

s) S201 - Z6 UC (6A) S201 - B2 (2A) 1.0 21.0

(525 A

1.5 31.5

RGC..25 1 pole
RGC..30 S201 - Z10 (10A) S201-B4 (4A) 1.0 7.6
(1800 A2s) 1.5 11.4

2.5 19.0

S201 - Z16 (16A) S201-B6 (6A) 1.0 5.2

1.5 7.8

2.5 13.0

4.0 20.8

S201 - Z20 (20A) S201-B10 (10A) 1.5 12.6

2.5 21.0

S201 - Z25 (25A) S201-B13 (13A) 2.5 25.0

4.0 40.0

2 pole
S202 - Z25 (25A) S202-B13 (13A) 2.5 19.0

4.0 30.4

RGC..40 1 pole
(3200 A2s) S201 - Z25 (25A) S201-B13 (13A) 2.5 7.0

4.0 11.2

6.0 16.8

RGC..60 1 pole
(3200 A2s) S201 - Z25 (25A) S201-B13 (13A) 2.5 7.0

4.0 11.2

6.0 16.8

RGC..90 1 pole

2

s) S201 - Z20 (20A) S201-B10 (10A) 1.5 4.2

(6600 A

2.5 7.0

4.0 11.2

S201 - Z32 (32A) S201-B16 (16A) 2.5 13.0

4.0 20.8

6.0 31.2

2 pole
S202 - Z20 (20A) S202-B10 (10A) 1.5 1.8

2.5 3.0

4.0 4.8

S202 - Z32 (32A) S202-B16 (16A) 2.5 5.0

4.0 8.0

6.0 12.0

10.0 20.0

S202 - Z50 (50A) S202-B25 (25A) 4.0 14.8

6.0 22.2

10.0 37.0

RGC..32 1 pole
RGC..42 S201-Z32 (32A) S201-B16 (16A) 2.5 3.0
RGC..62 4.0 4.8
RGC..92 6.0 7.2

2

(18000 A

S201-Z50 (50A) S201-B25 (25A) 4.0 4.8

s)

6.0 7.2

10.0 12.0

16.0 19.2

S201-Z63 (63A) S201-B32 (32A) 6.0 7.2

10.0 12.0

16.0 19.2

16. Between MCB and Load (including return path which goes back to the mains).
Note: A prospective current of 6kA and a 230/400V power supply system is assumed for the above suggested specifications. For cables with different cross
section than those mentioned above please consult Carlo Gavazzi’s Technical Support Group.

28 Specifications are subject to change without notice (22.05.2018)

RG...P19

The declaration in this section is prepared in compliance with People’s Republic of China Electronic Industry Standard SJ/
T11364-2014: Marking for the Restricted Use of Hazardous Substances in Electronic and Electrical Products.

Environmental Information

环境特性

RGC...E

Part Name Toxic or Harardous Substances and Elements

Power Unit Assembly x O O O O O

O: Indicates that said hazardous substance contained in homogeneous materials fot this part are below the limit require­ment of GB/T 26572.

X: Indicates that said hazardous substance contained in one of the homogeneous materials used for this part is above the
limit requirement of GB/T 26572.

Lead

(Pb)

Mercury

(Hg)

Cadmium

(Cd)

Hexavalent

Chromium

(Cr(Vl))

Polybrominated
biphenyls (PBB)

Polybrominated

diphenyl ethers

(PBDE)

零件名称 有毒或有害物质与元素

铅

(Pb)

功率单元 x O O O O O

O:此零件所有材料中含有的该有害物低于GB/T 26572的限定。

X: 此零件某种材料中含有的该有害物高于GB/T 26572的限定。

汞

(Hg)

镉

(Cd)

六价铬

(Cr(Vl))

多溴化联苯

(PBB)

多溴联苯醚

(PBDE)

25

Specifications are subject to change without notice (22.05.2018) 29

RGC...E

Accessories

Control Plugs

Ordering Key

Pack of 10 spring
loaded control plugs

* Refer to ‘Connection Specifications’ section for further details.

RGM25

30 Specifications are subject to change without notice (22.05.2018)